The Armadillo 800 EVA panel module has a backlight enable signal
connected to GPIO 61. Report this in the backlight DT node.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Commit 22ceeee1 ("pwm-backlight: Add
power supply support") added a mandatory power supply for the PWM
backlight. Add a fixed 5V regulator and reference it for the backlight
power supply.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The koelsch board uses has an SH ethernet controller which uses a Micrel
phy. Select MICREL_PHY for koelsch if SH_ETH is enabled to make use of the
Micrel-specific phy driver rather than relying on the generic phy driver.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Linux 3.13-rc3

Conflicts:
	drivers/pinctrl/sh-pfc/pfc-r8a7740.c
	drivers/pinctrl/sh-pfc/pfc-sh7372.c

This is a commit from the for-next branch of Linus Walleij's pin control tre
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl.git

It is the oldest commit in that branch that provides the dependencies
needed for SoC changes to the usage of sh-pfc.

When CONFIG_COMMON_CLOCK is enabled, call rcar_gen2_clocks_init() in the
timer init function to initialize the common clock framework before
initializing the clock sources. This will take care of clock
initialization when the r8a779[01] boards will be switched to
multiplatform kernels.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add macros usable by device tree sources to reference r8a7791 clocks by
index.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add macros usable by device tree sources to reference r8a7790 clocks by
index.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Prepare the clock at probe time, as there is no other appropriate place
in the driver where we're allowed to sleep.

Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

The PCI sub-system is not enabled by default on ARM and on certain
Renesas devices the build does not select it. This means that there
are configurations that do not allow the AHB-PCI bridge used for the
USB sub-systems to be built.

For the R8A7790, R8A7791 and EMEV-2 select MIGHT_HAVE_PCI to allow the
PCI drivers to be built. Also select MIGHT_HAVE_PCI for the multi-config
where there may be many Reneasas devices selected.
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Turn clk_enable() and clk_disable() calls into clk_prepare_enable() and
clk_disable_unprepare() to get ready for the migration to the common
clock framework.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The break timer accesses hardware registers and thus requires the port
to be enabled. It currently ensures this by enabling the port at the
beginning of the timer handler, and disabling it at the end. However,
the enable/disable operations call the runtime PM sync functions, which
are not allowed in atomic context. The current situation is thus broken.

This change relies on non-atomic code to enable/disable the port. The
break timer will only be started from the IRQ handler, which already
runs with the port enabled. We just need to ensure that the port won't
be disabled with the timer running, and that's easily done by just
cancelling the timer in the port disable function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

MSTP clocks are gate clocks controlled through a register that handles
up to 32 clocks. The register is often sparsely populated.

Those clocks are found on Renesas ARM SoCs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>

DIV6 clocks are divider gate clocks controlled through a single
register. The divider is expressed on 6 bits, hence the name, and can
take values from 1/1 to 1/64.

Those clocks are found on Renesas ARM SoCs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>

The R-Car Gen2 SoCs (R8A7790 and R8A7791) have several clocks that are
too custom to be supported in a generic driver. Those clocks can be
divided in two categories:

- Fixed rate clocks with multiplier and divisor set according to boot
  mode configuration

- Custom divider clocks with SoC-specific divider values

This driver supports both.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>

On non-DT platforms IRQ controllers associated with the GPIOs have a
fixed IRQ base value known at compile time. The sh-pfc driver translates
GPIO number to IRQ numbers using a hardcoded table. This mechanism
breaks on DT platforms, as the IRQ base values are dynamic in that case.

Fix this by specifying IRQs associated with GPIOs in IRQ resources,
populated automatically from the device tree. When IRQ resources are
specified the driver requires one IRQ resource per GPIO able to generate
an interrupt, and uses the translation table to compute the IRQ resource
offset instead of the IRQ number.

Cc: devicetree@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

There's more than one window, name the field windows.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes catching duplicate entries easier. Merge the two IRQ9 entries
found after sorting.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The external IRQ15 input multiplexed on GPIO 0 is missing. Add it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

0 is a valid GPIO value, use -1 to terminate the gpios array in IRQ
lists.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Some indices take positive values only, make them unsigned.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

ops->pin_config_get() is only used in one specific path that will only be taken
for generic pinconf drivers (ops->is_generic == true) when dumping the pinconf
by using debugfs.

By removing the check in pinconf_check_ops(), let's stop pressuring people to
write a pin_config_get() function that will never be used and so will probably
never be tested.

Removing the check in pinconf_pins_show() allows driver to not implement
pin_config_get() but still get a dump of the pinconf in debugfs by implementing
pin_config_dbg_show().

Finally, not implementing pin_config_get() now results in returning -ENOTSUPP
instead of -EINVAL. While this doesn't have any real impact for now, this feels
more right.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

When passing a not initialized config parameter, at91_pinconf_get() would return
a bogus value. Fix that by initializing it to zero before using it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The board has 7 buttons connected to GPIOs, add a corresponding
gpio-keys device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Use the %zu and %pad printk specifiers to print size_t and dma_addr_t
variables, and cast pointers to uintptr_t instead of unsigned int where
applicable. This fixes warnings on platforms where pointers and/or
dma_addr_t have a different size than int.

Cc: linux-serial@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

HPB-DMAC has 2 channel for USB Func (= D0/D1)
D0 is used as Tx, D1 is used as Rx on this patch
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

If the system has been started in non-secure mode, then the ARM generic
timer is not configurable during the kernel initialisation. Currently
the only thing we can check for is if the timer has been correctly
configured during the boot process.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add support for R8A7791 Ether clock.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

<linux/platform_data/camera-rcar.h> is needed on BockW,
not setup-r8a7778.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch support FSI-AK4648 with simple audio card
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>