This reverts commit 71130f29.

In commit 71130f29 ("vxlan: fix tos value before xmit") we want to
make sure the tos value are filtered by RT_TOS() based on RFC1349.

       0     1     2     3     4     5     6     7
    +-----+-----+-----+-----+-----+-----+-----+-----+
    |   PRECEDENCE    |          TOS          | MBZ |
    +-----+-----+-----+-----+-----+-----+-----+-----+

But RFC1349 has been obsoleted by RFC2474. The new DSCP field defined like

       0     1     2     3     4     5     6     7
    +-----+-----+-----+-----+-----+-----+-----+-----+
    |          DS FIELD, DSCP           | ECN FIELD |
    +-----+-----+-----+-----+-----+-----+-----+-----+

So with

IPTOS_TOS_MASK          0x1E
RT_TOS(tos)		((tos)&IPTOS_TOS_MASK)

the first 3 bits DSCP info will get lost.

To take all the DSCP info in xmit, we should revert the patch and just push
all tos bits to ip_tunnel_ecn_encap(), which will handling ECN field later.

Fixes: 71130f29 ("vxlan: fix tos value before xmit")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The way we define the phase (the difference between the time of the
signal's rising edge, and the closest integer multiple of the period),
it doesn't make sense to have a phase value equal or larger than 1
period.

So deny these settings coming from the user.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The wrappers in include/linux/pci-dma-compat.h should go away.

The patch has been generated with the coccinelle script below and has been
hand modified to replace GFP_ with a correct flag.
It has been compile tested.

When memory is allocated in 'fst_add_one()', GFP_KERNEL can be used
because it is a probe function and no lock is acquired.

@@
@@
-    PCI_DMA_BIDIRECTIONAL
+    DMA_BIDIRECTIONAL

@@
@@
-    PCI_DMA_TODEVICE
+    DMA_TO_DEVICE

@@
@@
-    PCI_DMA_FROMDEVICE
+    DMA_FROM_DEVICE

@@
@@
-    PCI_DMA_NONE
+    DMA_NONE

@@
expression e1, e2, e3;
@@
-    pci_alloc_consistent(e1, e2, e3)
+    dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3;
@@
-    pci_zalloc_consistent(e1, e2, e3)
+    dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3, e4;
@@
-    pci_free_consistent(e1, e2, e3, e4)
+    dma_free_coherent(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_map_single(e1, e2, e3, e4)
+    dma_map_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_single(e1, e2, e3, e4)
+    dma_unmap_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4, e5;
@@
-    pci_map_page(e1, e2, e3, e4, e5)
+    dma_map_page(&e1->dev, e2, e3, e4, e5)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_page(e1, e2, e3, e4)
+    dma_unmap_page(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_map_sg(e1, e2, e3, e4)
+    dma_map_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_sg(e1, e2, e3, e4)
+    dma_unmap_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+    dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_single_for_device(e1, e2, e3, e4)
+    dma_sync_single_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+    dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+    dma_sync_sg_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2;
@@
-    pci_dma_mapping_error(e1, e2)
+    dma_mapping_error(&e1->dev, e2)

@@
expression e1, e2;
@@
-    pci_set_dma_mask(e1, e2)
+    dma_set_mask(&e1->dev, e2)

@@
expression e1, e2;
@@
-    pci_set_consistent_dma_mask(e1, e2)
+    dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

The wrappers in include/linux/pci-dma-compat.h should go away.

The patch has been generated with the coccinelle script below and has been
hand modified to replace GFP_ with a correct flag.
It has been compile tested.

When memory is allocated in 'wanxl_pci_init_one()', GFP_KERNEL can be used
because it is a probe function and no lock is acquired.
Moreover, just a few lines above, GFP_KERNEL is already used.

@@
@@
-    PCI_DMA_BIDIRECTIONAL
+    DMA_BIDIRECTIONAL

@@
@@
-    PCI_DMA_TODEVICE
+    DMA_TO_DEVICE

@@
@@
-    PCI_DMA_FROMDEVICE
+    DMA_FROM_DEVICE

@@
@@
-    PCI_DMA_NONE
+    DMA_NONE

@@
expression e1, e2, e3;
@@
-    pci_alloc_consistent(e1, e2, e3)
+    dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3;
@@
-    pci_zalloc_consistent(e1, e2, e3)
+    dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3, e4;
@@
-    pci_free_consistent(e1, e2, e3, e4)
+    dma_free_coherent(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_map_single(e1, e2, e3, e4)
+    dma_map_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_single(e1, e2, e3, e4)
+    dma_unmap_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4, e5;
@@
-    pci_map_page(e1, e2, e3, e4, e5)
+    dma_map_page(&e1->dev, e2, e3, e4, e5)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_page(e1, e2, e3, e4)
+    dma_unmap_page(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_map_sg(e1, e2, e3, e4)
+    dma_map_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_sg(e1, e2, e3, e4)
+    dma_unmap_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+    dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_single_for_device(e1, e2, e3, e4)
+    dma_sync_single_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+    dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+    dma_sync_sg_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2;
@@
-    pci_dma_mapping_error(e1, e2)
+    dma_mapping_error(&e1->dev, e2)

@@
expression e1, e2;
@@
-    pci_set_dma_mask(e1, e2)
+    dma_set_mask(&e1->dev, e2)

@@
expression e1, e2;
@@
-    pci_set_consistent_dma_mask(e1, e2)
+    dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the accelerated networking SRIOV VF device has lost carrier
use the synthetic network device which is available as backup
path. This is a rare case since if VF link goes down, normally
the VMBus device will also loose external connectivity as well.
But if the communication is between two VM's on the same host
the VMBus device will still work.
Reported-by: "Shah, Ashish N" <ashish.n.shah@intel.com>
Fixes: 0c195567 ("netvsc: transparent VF management")
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix smatch warning:

drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c:2419
 alloc_channel() warn: passing zero to 'ERR_PTR'

setup_dpcon() should return ERR_PTR(err) instead of zero in error
handling case.

Fixes: d7f5a9d8 ("dpaa2-eth: defer probe on object allocate")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I just recently noticed that ethernet does not work anymore since v5.5
on the GARDENA smart Gateway, which is based on the AT91SAM9G25.
Debugging showed that the "GEM bits" in the NCFGR register are now
unconditionally accessed, which is incorrect for the !macb_is_gem()
case.

This patch adds the macb_is_gem() checks back to the code
(in macb_mac_config() & macb_mac_link_up()), so that the GEM register
bits are not accessed in this case any more.

Fixes: 7897b071 ("net: macb: convert to phylink")
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Reto Schneider <reto.schneider@husqvarnagroup.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for net:

1) Flush the cleanup xtables worker to make sure destructors
   have completed, from Florian Westphal.

2) iifgroup is matching erroneously, also from Florian.

3) Add selftest for meta interface matching, from Florian Westphal.

4) Move nf_ct_offload_timeout() to header, from Roi Dayan.

5) Call nf_ct_offload_timeout() from flow_offload_add() to
   make sure garbage collection does not evict offloaded flow,
   from Roi Dayan.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

A dead lock was triggered on thunderx driver:

        CPU0                    CPU1
        ----                    ----
   [01] lock(&(&nic->rx_mode_wq_lock)->rlock);
                           [11] lock(&(&mc->mca_lock)->rlock);
                           [12] lock(&(&nic->rx_mode_wq_lock)->rlock);
   [02] <Interrupt> lock(&(&mc->mca_lock)->rlock);

The path for each is:

  [01] worker_thread() -> process_one_work() -> nicvf_set_rx_mode_task()
  [02] mld_ifc_timer_expire()
  [11] ipv6_add_dev() -> ipv6_dev_mc_inc() -> igmp6_group_added() ->
  [12] dev_mc_add() -> __dev_set_rx_mode() -> nicvf_set_rx_mode()

To fix it, it needs to disable bh on [1], so that the timer on [2]
wouldn't be triggered until rx_mode_wq_lock is released. So change
to use spin_lock_bh() instead of spin_lock().

Thanks to Paolo for helping with this.

v1->v2:
  - post to netdev.
Reported-by: Rafael P. <rparrazo@redhat.com>
Tested-by: Dean Nelson <dnelson@redhat.com>
Fixes: 469998c8 ("net: thunderx: prevent concurrent data re-writing by nicvf_set_rx_mode")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stefano Brivio says:

====================
Support PMTU discovery with bridged UDP tunnels

Currently, PMTU discovery for UDP tunnels only works if packets are
routed to the encapsulating interfaces, not bridged.

This results from the fact that we generally don't have valid routes
to the senders we can use to relay ICMP and ICMPv6 errors, and makes
PMTU discovery completely non-functional for VXLAN and GENEVE ports of
both regular bridges and Open vSwitch instances.

If the sender is local, and packets are forwarded to the port by a
regular bridge, all it takes is to generate a corresponding route
exception on the encapsulating device. The bridge then finds the route
exception carrying the PMTU value estimate as it forwards frames, and
relays ICMP messages back to the socket of the local sender. Patch 1/6
fixes this case.

If the sender resides on another node, we actually need to reply to
IP and IPv6 packets ourselves and send these ICMP or ICMPv6 errors
back, using the same encapsulating device. Patch 2/6, based on an
original idea by Florian Westphal, adds the needed functionality,
while patches 3/6 and 4/6 add matching support for VXLAN and GENEVE.

Finally, 5/6 and 6/6 introduce selftests for all combinations of
inner and outer IP versions, covering both VXLAN and GENEVE, with
both regular bridges and Open vSwitch instances.

v2: Add helper to check for any bridge port, skip oif check for PMTU
    routes for bridge ports only, split IPv4 and IPv6 helpers and
    functions (all suggested by David Ahern)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The new tests check that IP and IPv6 packets exceeding the local PMTU
estimate, forwarded by an Open vSwitch instance from another node,
result in the correct route exceptions being created, and that
communication with end-to-end fragmentation, over GENEVE and VXLAN
Open vSwitch ports, is now possible as a result of PMTU discovery.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The new tests check that IP and IPv6 packets exceeding the local PMTU
estimate, both locally generated and forwarded by a bridge from
another node, result in the correct route exceptions being created,
and that communication with end-to-end fragmentation over VXLAN and
GENEVE tunnels is now possible as a result of PMTU discovery.

Part of the existing setup functions aren't generic enough to simply
add a namespace and a bridge to the existing routing setup. This
rework is in progress and we can easily shrink this once more generic
topology functions are available.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the interface is a bridge or Open vSwitch port, and we can't
forward a packet because it exceeds the local PMTU estimate,
trigger an ICMP or ICMPv6 reply to the sender, using the same
interface to forward it back.

If metadata collection is enabled, set destination and source
addresses for the flow as if we were receiving the packet, so that
Open vSwitch can match the ICMP error against the existing
association.

v2: Use netif_is_any_bridge_port() (David Ahern)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the interface is a bridge or Open vSwitch port, and we can't
forward a packet because it exceeds the local PMTU estimate,
trigger an ICMP or ICMPv6 reply to the sender, using the same
interface to forward it back.

If metadata collection is enabled, reverse destination and source
addresses, so that Open vSwitch is able to match this packet against
the existing, reverse flow.

v2: Use netif_is_any_bridge_port() (David Ahern)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's currently possible to bridge Ethernet tunnels carrying IP
packets directly to external interfaces without assigning them
addresses and routes on the bridged network itself: this is the case
for UDP tunnels bridged with a standard bridge or by Open vSwitch.

PMTU discovery is currently broken with those configurations, because
the encapsulation effectively decreases the MTU of the link, and
while we are able to account for this using PMTU discovery on the
lower layer, we don't have a way to relay ICMP or ICMPv6 messages
needed by the sender, because we don't have valid routes to it.

On the other hand, as a tunnel endpoint, we can't fragment packets
as a general approach: this is for instance clearly forbidden for
VXLAN by RFC 7348, section 4.3:

   VTEPs MUST NOT fragment VXLAN packets.  Intermediate routers may
   fragment encapsulated VXLAN packets due to the larger frame size.
   The destination VTEP MAY silently discard such VXLAN fragments.

The same paragraph recommends that the MTU over the physical network
accomodates for encapsulations, but this isn't a practical option for
complex topologies, especially for typical Open vSwitch use cases.

Further, it states that:

   Other techniques like Path MTU discovery (see [RFC1191] and
   [RFC1981]) MAY be used to address this requirement as well.

Now, PMTU discovery already works for routed interfaces, we get
route exceptions created by the encapsulation device as they receive
ICMP Fragmentation Needed and ICMPv6 Packet Too Big messages, and
we already rebuild those messages with the appropriate MTU and route
them back to the sender.

Add the missing bits for bridged cases:

- checks in skb_tunnel_check_pmtu() to understand if it's appropriate
  to trigger a reply according to RFC 1122 section 3.2.2 for ICMP and
  RFC 4443 section 2.4 for ICMPv6. This function is already called by
  UDP tunnels

- a new function generating those ICMP or ICMPv6 replies. We can't
  reuse icmp_send() and icmp6_send() as we don't see the sender as a
  valid destination. This doesn't need to be generic, as we don't
  cover any other type of ICMP errors given that we only provide an
  encapsulation function to the sender

While at it, make the MTU check in skb_tunnel_check_pmtu() accurate:
we might receive GSO buffers here, and the passed headroom already
includes the inner MAC length, so we don't have to account for it
a second time (that would imply three MAC headers on the wire, but
there are just two).

This issue became visible while bridging IPv6 packets with 4500 bytes
of payload over GENEVE using IPv4 with a PMTU of 4000. Given the 50
bytes of encapsulation headroom, we would advertise MTU as 3950, and
we would reject fragmented IPv6 datagrams of 3958 bytes size on the
wire. We're exclusively dealing with network MTU here, though, so we
could get Ethernet frames up to 3964 octets in that case.

v2:
- moved skb_tunnel_check_pmtu() to ip_tunnel_core.c (David Ahern)
- split IPv4/IPv6 functions (David Ahern)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, processes sending traffic to a local bridge with an
encapsulation device as a port don't get ICMP errors if they exceed
the PMTU of the encapsulated link.

David Ahern suggested this as a hack, but it actually looks like
the correct solution: when we update the PMTU for a given destination
by means of updating or creating a route exception, the encapsulation
might trigger this because of PMTU discovery happening either on the
encapsulation device itself, or its lower layer. This happens on
bridged encapsulations only.

The output interface shouldn't matter, because we already have a
valid destination. Drop the output interface restriction from the
associated route lookup.

For UDP tunnels, we will now have a route exception created for the
encapsulation itself, with a MTU value reflecting its headroom, which
allows a bridge forwarding IP packets originated locally to deliver
errors back to the sending socket.

The behaviour is now consistent with IPv6 and verified with selftests
pmtu_ipv{4,6}_br_{geneve,vxlan}{4,6}_exception introduced later in
this series.

v2:
- reset output interface only for bridge ports (David Ahern)
- add and use netif_is_any_bridge_port() helper (David Ahern)
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for v5.9

Second set of patches for v5.9. mt76 has most of patches this time.
Otherwise it's just smaller fixes and cleanups to other drivers.

There was a major conflict in mt76 driver between wireless-drivers and
wireless-drivers-next. I solved that by merging the former to the
latter.

Major changes:

rtw88

* add support for ieee80211_ops::change_interface

* add support for enabling and disabling beacon

* add debugfs file for testing h2c

mt76

* ARP filter offload for 7663

* runtime power management for 7663

* testmode support for mfg calibration

* support for more channels
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use netdev_<level> in place of VELOCITY_PRT.
Use pr_<level> in place of printk(KERN_<LEVEL>.

Miscellanea:

o Add pr_fmt to prefix pr_<level> output with "via-velocity: "
o Remove now unused functions and macros
o Realign some logging lines
o Remove devname where pr_<level> is also used
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Luo bin says:

====================
hinic: mailbox channel enhancement

add support to generate mailbox random id for VF to ensure that
the mailbox message from VF is valid and PF should check whether
the cmd from VF is supported before passing it to hw.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

PF should check whether the cmd from VF is supported and its content
is right before passing it to hw.
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

add support to generate mailbox random id of VF to ensure that
mailbox messages PF received are from the correct VF.
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mt76 driver had major conflicts within mt7615 directory. To make it easier for
every merge wireless-drivers to wireless-drivers-next and solve those
conflicts.

   drivers/net/ethernet/sfc/ef100_nic.c:835:3: error: 'const struct efx_nic_type' has no member named 'filter_rfs_expire_one'
     835 |  .filter_rfs_expire_one = efx_mcdi_filter_rfs_expire_one,
         |   ^~~~~~~~~~~~~~~~~~~~~
>> drivers/net/ethernet/sfc/ef100_nic.c:835:27: error: initialization of 'void (*)(struct efx_nic *, u32)' {aka 'void (*)(struct efx_nic *, unsigned int)'} from incompatible pointer type 'bool (*)(struct efx_nic *, u32,  unsigned int)' {aka '_Bool (*)(struct efx_nic *, unsigned int,  unsigned int)'} [-Werror=incompatible-pointer-types]
     835 |  .filter_rfs_expire_one = efx_mcdi_filter_rfs_expire_one,
         |                           ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf-next 2020-08-04

The following pull-request contains BPF updates for your *net-next* tree.

We've added 73 non-merge commits during the last 9 day(s) which contain
a total of 135 files changed, 4603 insertions(+), 1013 deletions(-).

The main changes are:

1) Implement bpf_link support for XDP. Also add LINK_DETACH operation for the BPF
   syscall allowing processes with BPF link FD to force-detach, from Andrii Nakryiko.

2) Add BPF iterator for map elements and to iterate all BPF programs for efficient
   in-kernel inspection, from Yonghong Song and Alexei Starovoitov.

3) Separate bpf_get_{stack,stackid}() helpers for perf events in BPF to avoid
   unwinder errors, from Song Liu.

4) Allow cgroup local storage map to be shared between programs on the same
   cgroup. Also extend BPF selftests with coverage, from YiFei Zhu.

5) Add BPF exception tables to ARM64 JIT in order to be able to JIT BPF_PROBE_MEM
   load instructions, from Jean-Philippe Brucker.

6) Follow-up fixes on BPF socket lookup in combination with reuseport group
   handling. Also add related BPF selftests, from Jakub Sitnicki.

7) Allow to use socket storage in BPF_PROG_TYPE_CGROUP_SOCK-typed programs for
   socket create/release as well as bind functions, from Stanislav Fomichev.

8) Fix an info leak in xsk_getsockopt() when retrieving XDP stats via old struct
   xdp_statistics, from Peilin Ye.

9) Fix PT_REGS_RC{,_CORE}() macros in libbpf for MIPS arch, from Jerry Crunchtime.

10) Extend BPF kernel test infra with skb->family and skb->{local,remote}_ip{4,6}
    fields and allow user space to specify skb->dev via ifindex, from Dmitry Yakunin.

11) Fix a bpftool segfault due to missing program type name and make it more robust
    to prevent them in future gaps, from Quentin Monnet.

12) Consolidate cgroup helper functions across selftests and fix a v6 localhost
    resolver issue, from John Fastabend.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2020-08-03

This patchset introduces some updates to mlx5 driver.

1) Jakub converts mlx5 to use the new udp tunnel infrastructure.
   Starting with a hack to allow drivers to request a static configuration
   of the default vxlan port, and then a patch that converts mlx5.

2) Parav implements change_carrier ndo for VF eswitch representors,
   to speedup link state control of representors netdevices.

3) Alex Vesker, makes a simple update to software steering to fix an issue
   with push vlan action sequence

4) Leon removes a redundant dump stack on error flow.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Edward Cree says:

====================
sfc: driver for EF100 family NICs, part 2

This series implements the data path and various other functionality
 for Xilinx/Solarflare EF100 NICs.

Changed from v2:
 * Improved error handling of design params (patch #3)
 * Removed 'inline' from .c file in patch #4
 * Don't report common stats to ethtool -S (patch #8)

Changed from v1:
 * Fixed build errors on CONFIG_RFS_ACCEL=n (patch #5) and 32-bit
   (patch #8)
 * Dropped patch #10 (ethtool ops) as it's buggy and will need a
   bigger rework to fix.
====================
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We don't yet have a .sriov_configure() to create them, though.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We'll need it later, for VF representors.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Self-tests for event and interrupt reception and NVRAM.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MAC stats work much the same as on EF10, with a periodic DMA to a region
 specified via an MCDI.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bring down the TX and RX queues at ifdown, so that we can then fini the
 EVQs (otherwise the MC would return EBUSY because they're still in use).
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Includes RSS spreading.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Includes checksum offload and TSO, so declare those in our netdev features.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Several parts of the EF100 architecture are parameterised (to allow
 varying capabilities on FPGAs according to resource constraints), and
 these parameters are exposed to the driver through a TLV-encoded
 region of the BAR.
For the most part we either don't care about these values at all or
 just need to sanity-check them against the driver's assumptions, but
 there are a number of TSO limits which we record so that we will be
 able to check against them in the TX path when handling GSO skbs.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the future, EF100 is planned to have a credit-based scheme for
 handling unsolicited events, which drivers will need to use in order
 to function correctly.  However, current EF100 hardware does not yet
 generate unsolicited events and the credit scheme has not yet been
 implemented in firmware.  To prevent compatibility problems later if
 the current driver is used with future firmware which does implement
 it, we check for the corresponding capability flag (which that
 future firmware will set), and if found, we refuse to probe.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Early in EF100 development there was a different format of event
 descriptor; if the NIC is somehow running the very old firmware
 which will use that format, fail the probe.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver calls napi_schedule_irqoff() from a context where, in RT,
hardirqs are not disabled, since the IRQ handler is force-threaded.

In the call path of this function, __raise_softirq_irqoff() is modifying
its per-CPU mask of pending softirqs that must be processed, using
or_softirq_pending(). The or_softirq_pending() function is not atomic,
but since interrupts are supposed to be disabled, nobody should be
preempting it, and the operation should be safe.

Nonetheless, when running with hardirqs on, as in the PREEMPT_RT case,
it isn't safe, and the pending softirqs mask can get corrupted,
resulting in softirqs being lost and never processed.

To have common code that works with PREEMPT_RT and with mainline Linux,
we can use plain napi_schedule() instead. The difference is that
napi_schedule() (via __napi_schedule) also calls local_irq_save, which
disables hardirqs if they aren't already. But, since they already are
disabled in non-RT, this means that in practice we don't see any
measurable difference in throughput or latency with this patch.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver calls napi_schedule_irqoff() from a context where, in RT,
hardirqs are not disabled, since the IRQ handler is force-threaded.

In the call path of this function, __raise_softirq_irqoff() is modifying
its per-CPU mask of pending softirqs that must be processed, using
or_softirq_pending(). The or_softirq_pending() function is not atomic,
but since interrupts are supposed to be disabled, nobody should be
preempting it, and the operation should be safe.

Nonetheless, when running with hardirqs on, as in the PREEMPT_RT case,
it isn't safe, and the pending softirqs mask can get corrupted,
resulting in softirqs being lost and never processed.

To have common code that works with PREEMPT_RT and with mainline Linux,
we can use plain napi_schedule() instead. The difference is that
napi_schedule() (via __napi_schedule) also calls local_irq_save, which
disables hardirqs if they aren't already. But, since they already are
disabled in non-RT, this means that in practice we don't see any
measurable difference in throughput or latency with this patch.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: loop: Preparatory changes for 802.1Q data path
Florian Fainelli says:

====================
These patches are all meant to help pave the way for a 802.1Q data path
added to the mockup driver, making it more useful than just testing for
configuration. Sending those out now since there is no real need to
wait.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>