If the controller has no PCIe module attached, accessing of the device
configuration space causes a data bus error. Avoid this by checking the
status of the PCIe link in advance, and indicate an error if the link
is down.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4293/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

2ec8663f9c03a96f2c328c7c483603c31d62ad37 (lmo) rsp.
497e5ff0 (kernel.org) [MIPS: Malta: Move
PIIX4 PCI fixup to where it belongs.] attempted to move this PCI fixup
but really only added it at it's new location without deleting the old
instance.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The ath79 platform code allows to run a single kernel image on various
SoCs which are based on the 24Kc and 74Kc cores.  The current code
explicitely disables the DSP ASE, but that is available in the 74Kc core.

Remove the override in order to let the kernel to detect the availability
of the DSP ASE at runtime.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4222/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The current implementation of synchronise_count_{master,slave} blocks
slave CPUs in early boot until all of them come up. This no longer
works because blocking a CPU with interrupts off after notifying the
CPU to be online causes problems with the current kernel.

Specifically, after the workqueue changes
(commit a08489c5 "Pull workqueue changes from Tejun Heo")
the CPU_ONLINE notification callback workqueue_cpu_up_callback()
will hang on wait_for_completion(&idle_rebind.done), if the slave
CPUs are blocked for synchronize_count_slave().

The changes are to update synchronize_count_{master,slave}() to handle
one CPU at a time and to call synchronise_count_master() in __cpu_up()
so that the CPU_ONLINE notification goes out only after the COP0 COUNT
register is synchronized.

[ralf@linux-mips.org: This matter only to those few platforms which are
using the cp0 counter as their clocksource which are XLP, XLR and MIPS'
CMP solution.]
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4216/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

BCM6338 and BCM6348 have a message control register width of 8 bits, instead
of 16-bits like what the SPI driver assumes right now. Also the SPI message
type shift value of 14 is actually 6 for these SoCs.
This resulted in transmit FIFO corruption because we were writing 16-bits
to an 8-bits wide register, thus spanning on the first byte of the transmit
FIFO, which had already been filed in bcm63xx_spi_fill_txrx_fifo().

Fix this by passing the message control register width and message type
shift through platform data back to the SPI driver so that it can use
it properly.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: grant.likely@secretlab.ca
Cc: spi-devel-general@lists.sourceforge.net
Cc: jonas.gorski@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/3983/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

In case a series of R_MIPS_HI16 relocations was not followed by an
R_MIPS_LO16 relocation we were leaking the hi16 relocation chain.
Handle that error and return an error.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The relocation code was essentially taken from the 2.4 modutils which
perform relocation in userspace.  In 2.6 relocation of multiple modules
may be performed in parallel by the in-kernel loader so the global
variable mips_hi16_list won't fly anymore.  Fix race by moving it into
mod_arch_specific.

[ralf@linux-mips.org: folded in Tony's followup fix.  Thanks Tony!]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Tony Wu <tung7970@gmail.com>
Cc:  linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/4189/

Commit 6f5d2e970452b5c86906adcb8e7ad246f535ba39 (lmo) /
477c4b07 (kernel.org) [[MIPS: VPE: Free
relocation chain on error.] fixed the same issue in the vpe loader in 2009
but back then the same bug in module.c went unfixed.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Akhilesh Kumar <akhilesh.lxr@gmail.com>

Without this udelay(1) PCI idsel does not work correctly on the
"singleboard" (T-Mobile Surfbox) for the MiniPCI device. The result is
that PCI configuration fails and the MiniPCI card is not detected
correctly. Instead of

PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fffffff]
pci_bus 0000:00: root bus resource [io  0x1000-0xffff]
pci 0000:00:03.0: BAR 0: assigned [mem 0x40000000-0x4000ffff]
pci 0000:00:00.0: BAR 0: assigned [mem 0x40010000-0x40010fff]
pci 0000:00:00.1: BAR 0: assigned [mem 0x40011000-0x40011fff]

We see only the CardBus device:

PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fffffff]
pci_bus 0000:00: root bus resource [io  0x1000-0xffff]
pci 0000:00:00.0: BAR 0: assigned [mem 0x40000000-0x40000fff]
pci 0000:00:00.1: BAR 0: assigned [mem 0x40001000-0x40001fff]

Later the device driver shows this error:

ath5k 0000:00:03.0: cannot remap PCI memory region
ath5k: probe of 0000:00:03.0 failed with error -5

I assume that the logic chip which usually supresses the signal to the CardBus
card has some settling time and without the delay it would still let the
Cardbus interfere with the response from the MiniPCI card.

What I cannot explain is why this behaviour shows up now and not in earlier
kernel versions before. Maybe older PCI code was slower?
Signed-off-by: Bruno Randolf <br1@einfach.org>
Cc: linux-mips@linux-mips.org
Cc: manuel.lauss@googlemail.com
Cc: florian@openwrt.org
Patchwork: https://patchwork.linux-mips.org/patch/4087/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

It is needed in order to get rid of the following errors:

arch/mips/ath79/clock.c:353:13: error: redefinition of 'clk_get'
include/linux/clk.h:281:27: note: previous definition of 'clk_get' was here
arch/mips/ath79/clock.c:377:5: error: redefinition of 'clk_enable'
include/linux/clk.h:295:19: note: previous definition of 'clk_enable' was here
arch/mips/ath79/clock.c:383:6: error: redefinition of 'clk_disable'
include/linux/clk.h:300:20: note: previous definition of 'clk_disable' was here
arch/mips/ath79/clock.c:388:15: error: redefinition of 'clk_get_rate'
include/linux/clk.h:302:29: note: previous definition of 'clk_get_rate' was here
arch/mips/ath79/clock.c:394:6: error: redefinition of 'clk_put'
include/linux/clk.h:291:20: note: previous definition of 'clk_put' was here
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4170/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The currently assigned IRQ number to the OHCI controller is incorrect for
the AR7240 SoC, and that leads to the following error message from the
OHCI driver:

ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ath79-ohci ath79-ohci: Atheros built-in OHCI controller
ath79-ohci ath79-ohci: new USB bus registered, assigned bus number 1
ath79-ohci ath79-ohci: irq 14, io mem 0x1b000000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usb 1-1: new full-speed USB device number 2 using ath79-ohci
ath79-ohci ath79-ohci: Unlink after no-IRQ?  Controller is probably using the wrong IRQ.

Fix this by using the correct IRQ number.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4168/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The AR724[12] SoCs have more GPIO lines than the AR7240.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Cc: linux-mips@linux-mips.org
Patchwork: https://http://patchwork.linux-mips.org/patch/4167/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Since 3.6.0-rc1,  We are getting many messages like:

WARNING: at kernel/irq/irqdomain.c:444 irq_domain_associate_many+0x23c/0x260()
Modules linked in:
Call Trace:
[<ffffffff814cb698>] dump_stack+0x8/0x34
[<ffffffff81133d00>] warn_slowpath_common+0x78/0xa8
[<ffffffff81187e44>] irq_domain_associate_many+0x23c/0x260
[<ffffffff81187f38>] irq_create_mapping+0xd0/0x220
[<ffffffff81188104>] irq_create_of_mapping+0x7c/0x158
[<ffffffff813e5f08>] irq_of_parse_and_map+0x28/0x40
.
.
.

Both the CIU and GPIO interrupt domains were somewhat screwed up.

For the CIU domain, we need to call irq_domain_associate() for each of
the preassigned irq numbers.  For the GPIO domain, we were applying
the register bit offset in octeon_irq_gpio_xlat, but it should be done
in octeon_irq_gpio_map instead.

Also: Reserve all 8 'core' irqs for the 'core' irq_chip so that they
don't get used by the other domains.  Remove unused OCTEON_IRQ_*
symbols.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4190/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Following a report of a crash during an automount expire I found that
the locking in fs/autofs4/expire.c:get_next_positive_subdir() was wrong.
Not only is the locking wrong but the function is more complex than it
needs to be.

The function is meant to calculate (and dget) the next entry in the list
of directories contained in the root of an autofs mount point (an autofs
indirect mount to be precise). The main problem was that the d_lock of
the owner of the list was not being taken when walking the list, which
lead to list corruption under load. The only other lock that needs to
be taken is against the next dentry candidate so it can be checked for
usability.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull VFIO fix from Alex Williamson:
 "Just a trivial patch to include vfio.h in the installed headers so we
  can complete userspace integration into QEMU."

* tag 'vfio-for-v3.6-rc1' of git://github.com/awilliam/linux-vfio:
  vfio: Include vfio.h in installed headers

Pull fuse updates from Miklos Szeredi.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: verify all ioctl retry iov elements
  fuse: add missing INIT flag descriptions
  fuse: add missing INIT flags
  fuse: update attributes on aio_read
  fuse: invalidate inode mapping if mtime changes
  fuse: add FUSE_AUTO_INVAL_DATA init flag

Merge tag 'stable/for-linus-3.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

Pull Xen fix from Konrad Rzeszutek Wilk:
 "Way back in v3.5 we added a mechanism to populate back pages that were
  released (they overlapped with MMIO regions), but neglected to reserve
  the proper amount of virtual space for extend_brk to work properly.

  Coincidentally some other commit aligned the _brk space to larger area
  so I didn't trigger this until it was run on a machine with more than
  2GB of MMIO space."

 * On machines with large MMIO/PCI E820 spaces we fail to boot b/c
   we failed to pre-allocate large enough virtual space for extend_brk.

* tag 'stable/for-linus-3.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/p2m: Reserve 8MB of _brk space for P2M leafs when populating back.

Pull SuperH fixes from Paul Mundt.

* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
  sh: intc: Handle domain association for sparseirq pre-allocated vectors.
  sh: sh7269: Fix LCD pinmux
  sh: dma: fix request_irq usage

Moved to djbw@fb.com

Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Dan Williams <djbw@fb.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When dumping "Code: " sections from an oops, the trapping instruction
%rip points to can be a string copy

  2b:*  f3 a5                   rep movsl %ds:(%rsi),%es:(%rdi)

and the line contain a bunch of ":".  Current "cut" selects only the and
the second field output looks funnily overlaid this:

  2b:*  f3 a5                   rep movsl %ds     <-- trapping instruction:(%rsi),%es:(%rdi

Fix this by selecting the remaining fields too.

Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-kbuild@vger.kernel.org
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull two slave-dmaengine fixes from Vinod Koul:
 "One fixes the correct use of clock API in imx driver and the other
  enables clock for tegra driver, which is used for other tegra driver
  conversion to dmanegine in -next."

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dma: tegra: enable/disable dma clock
  dma: imx-dma: Fix kernel crash due to missing clock conversion

Pull more drm fixes from Dave Airlie:
 "Just some intel and nouveau ones this time, intel has more edp panel
  fixes for macbooks and nouveau has a suspend/resume regression fix in
  there."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/i915: Apply post-sync write for pipe control invalidates
  drm/i915: reorder edp disabling to fix ivb MacBook Air
  drm/nv86/fifo: suspend fix
  drm/nouveau: disable copy engine on NVAF
  nouveau: fixup scanout enable in nvc0_pm
  drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
  drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate
  drm/i915: ensure i2c adapter is all set before adding it
  drm/i915: ignore eDP bpc settings from vbt
  drm/i915: Fix blank panel at reopening lid
  drm/nve0/fifo: add support for the flip completion swmthd

Pull two sparc fixes from David S. Miller.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Be less verbose during vmemmap population.
  sparc64: do not clobber personality flags in sys_sparc64_personality()

* 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6:
  drm/nv86/fifo: suspend fix
  drm/nouveau: disable copy engine on NVAF
  nouveau: fixup scanout enable in nvc0_pm
  drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
  drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate
  drm/nve0/fifo: add support for the flip completion swmthd

Daniel Vetter writes:

"A few important fixers:
- fix various lvds backlight issues, regressed in 3.6 (Takashi Iwai)
- make the retina mbp work (ignore bogus edp bpc value in vbt)
- fix a gmbus regression introduced in (iirc) 3.4 (Jani Nikula)
- fix an edp panel power sequence regression, fixes the new macbook air
- apply the tlb invalidate w/a

Otherwise we still have another gmbus regression (patches are awaiting
tested-bys) and there's something odd going with some rare systems not
entering rc6 often enough (and hence blowing through too much power).  It
seems to be a timing-related issue and can be mitigated by frobbing the
magic tuning parameters. We're still working on that one. Also, we still
have some fallout from the hw context support, but you can only hit that
with mesa master."

* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
  drm/i915: Apply post-sync write for pipe control invalidates
  drm/i915: reorder edp disabling to fix ivb MacBook Air
  drm/i915: ensure i2c adapter is all set before adding it
  drm/i915: ignore eDP bpc settings from vbt
  drm/i915: Fix blank panel at reopening lid

On a 2-node machine with 256GB of ram we get 512 lines of
console output, which is just too much.

This mimicks Yinghai Lu's x86 commit c2b91e2e
(x86_64/mm: check and print vmemmap allocation continuous) except that
we aren't ever going to get contiguous block pointers in between calls
so just print when the virtual address or node changes.

This decreases the output by an order of 16.

Also demote this to KERN_DEBUG.
Signed-off-by: David S. Miller <davem@davemloft.net>

When invalidating the TLBs it is documentated as requiring a post-sync
write. Failure to do so seems to result in a GPU hang.

Exposure to this hang on IVB seems to be a result of removing the extra
stalls required for SNB pipecontrol workarounds:

commit 6c6cf5aa
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Fri Jul 20 18:02:28 2012 +0100

    drm/i915: Only apply the SNB pipe control w/a to gen6

Note: Manually switch the pipe_control cmd to 4 dwords to avoid a
(silent) functional conflict with -next. This way will get a loud (but
conflict with next (since the scratch_addr has been deleted there).

Reported-and-tested-by: yex.tian@intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=53322Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: added note about merge conflict with -next.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

eDP is tons of fun. It turns out that at least the new MacBook Air 5,1
model absolutely doesn't like the new force vdd dance we've introduced
in

commit 6cb49835
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Sun May 20 17:14:50 2012 +0200

    drm/i915: enable vdd when switching off the eDP panel

But that patch also tried to fix some neat edp sequence issue with the
force_vdd timings. Closer inspection reveals that we've raised
force_vdd only to do the aux channel communication dp_sink_dpms. If we
move the edp_panel_off below that, we don't need any force_vdd for the
disable sequence, which makes the Air happy.

Unfortunately the reporter of the original bug that the above commit
fixed is travelling, so we can't test whether this regresses things.
But my theory is that since we don't check for any power-off ->
force_vdd-on delays in edp_panel_vdd_on, this was the actual
root-cause of this failure. With that force_vdd dance completely
eliminated, I'm hopeful the original bug stays fixed, too.

For reference the old bug, which hopefully doesn't get broken by this:

https://bugzilla.kernel.org/show_bug.cgi?id=43163

In any case, regression fixers win over plain bugfixes, so this needs
to go in asap.

v2: The crucial pieces seems to be to clear the force_vdd flag
uncoditionally, too, in edp_panel_off. Looks like this is left behind
by the firmware somehow.

v3: The Apple firmware seems to switch off the panel on it's own, hence
we still need to keep force_vdd on, but properly clear it when switching
the panel off.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=45671Tested-by: Roberto Romer <sildurin@gmail.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Tested-by: Keith Packard <keithp@keithp.com>
Cc: stable@vger.kernel.org
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Pull s390 patches from Martin Schwidefsky:
 "Included are bug fixes and a patch to enable system call filtering
  with BPF."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/compat: fix mmap compat system calls
  s390/compat: fix compat wrappers for process_vm system calls
  s390: do not clobber personality flags in sys_32_personality()
  s390/seccomp: add support for system call filtering using BPF
  s390/sclp_sdias: Add missing break and "fall through"
  s390/mm: remove MAX_PHYSADDR_BITS define

Pull drm fixes from Dave Airlie:
 "Radeon and intel fixes mostly, one fix to the mgag200 driver to not
  hang on certain server variants."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (32 commits)
  drm/radeon: fix typo in function header comment
  drm/radeon/kms: implement timestamp userspace query (v2)
  drm/radeon/kms: add MSAA texture support for r600-evergreen
  drm/radeon/kms: reorder code in r600_check_texture_resource
  drm/radeon: fence virtual address and free it once idle v4
  drm/radeon: fix some missing parens in asic macros
  drm/radeon: add some new SI pci ids
  drm/radeon: fix ordering in pll picking on dce4+
  drm/radeon: do not reenable crtc after moving vram start address
  drm/radeon: fix bank tiling parameters on cayman
  drm/radeon: fix bank tiling parameters on evergreen
  drm/radeon: fix bank tiling parameters on SI
  drm/radeon: properly handle crtc powergating
  drm/radeon: properly handle SS overrides on TN (v2)
  drm/radeon/dce4+: set a more reasonable cursor watermark
  drm/radeon: fix handling for ddc type 5 on combios
  drm/mgag200: fix G200ER pll picking algorithm
  drm/edid: Fix potential memory leak in edid_load()
  drm/udl: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(.. [1]
  drm/radeon/kms: allow "invalid" DB formats as a means to disable DB
  ...

Commit 72121572 ("GPIO: gpio-pxa: fix devicetree functions") added an
"xlate" function pointer to the irq_domain_ops, but this function is nor
declared or defined anywhere when CONFIG_OF is disabled, causing the
build error:

  drivers/gpio/gpio-pxa.c:532:11: error: 'irq_domain_xlate_twocell' undeclared here (not in a function)

Extending the DT-only code section to cover the irq_domain_ops and the
pxa_gpio_dt_ids solves this problem and makes it clearer which code is
actually used without DT.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This fix is a backport from the reworked nouveau driver.  It masks off the
engines we're not expecting to use before attempting a channel kickoff.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

The copy engine exhibits random memory corruption in at least one case, the
GeForce 320M (nv50, 0xaf) in the MacBookAir3,1.

This patch omits creating the engine for the specific chipset, falling back
to M2MF, which kills the symptoms.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Fixes screen being black after changing performance level.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: stable@vger.kernel.org [3.5+]
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

At least partially fixes DP output detection on W530.  Not sure if more
issues remain, or if my adaptor is just behaving weirdly (it does that
sometimes).

In any case, this patch is necessary.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Christoph Bumiller <e0425955@student.tuwien.ac.at>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org

Alex Deucher writes:
This is the current set of radeon fixes for 3.6.  Nothing too major.

Highlights:
- various display fixes
- some SI fixes
- new SI pci ids
- major VM fix
- CS checker support for MSAA

I've tested on a number of cards across generations and noticed no problems.

* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: fix typo in function header comment
  drm/radeon/kms: implement timestamp userspace query (v2)
  drm/radeon/kms: add MSAA texture support for r600-evergreen
  drm/radeon/kms: reorder code in r600_check_texture_resource
  drm/radeon: fence virtual address and free it once idle v4
  drm/radeon: fix some missing parens in asic macros
  drm/radeon: add some new SI pci ids
  drm/radeon: fix ordering in pll picking on dce4+
  drm/radeon: do not reenable crtc after moving vram start address
  drm/radeon: fix bank tiling parameters on cayman
  drm/radeon: fix bank tiling parameters on evergreen
  drm/radeon: fix bank tiling parameters on SI
  drm/radeon: properly handle crtc powergating
  drm/radeon: properly handle SS overrides on TN (v2)
  drm/radeon/dce4+: set a more reasonable cursor watermark
  drm/radeon: fix handling for ddc type 5 on combios

i2c_add_adapter() may do i2c transfers on the bus to detect supported
devices. Therefore the adapter needs to be all set before adding it. This
was not the case for the bit-banging fallback, resulting in an oops if the
device detection GMBUS transfers timed out. Fix the issue by calling
i2c_add_adapter() only after intel_gpio_setup().

LKML-Reference: <5021F00B.7000503@ionic.de>
Tested-by: Mihai Moldovan <ionic@ionic.de>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: Dmitrii Cherkasov <DCherkasov@luxsoft.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>