This patch adds delay P0 to P1/P2/P3 quirk for U2/U2/U3, and some special
platforms can configure that if it is needed.

[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch adds request P1/P2/P3 quirk for U2/U2/U3, and some special
platforms can configure that if it is needed.

[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch adds P3 in U2 SS inactive quirk, and some special platforms can
configure that if it is needed.

[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch adds u2exit lfps quirk, and some special platforms can configure
that if it is needed.

[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

When parameter DWC_USB3_LPM_ERRATA_ENABLE is enabled in Andvanced
Configuration of coreConsultant, it supports of xHCI BESL Errata Dated
10/19/2011 is enabled in host mode. In device mode it adds the capability
to send NYET response threshold based on the BESL value received in the LPM
token, and the threhold is configurable for each soc platform.

This patch adds an entry that soc platform is able to define the lpm
capacity with their own device tree or bus glue layer.

[ balbi@ti.com : added devicetree documentation, spelled threshold
		completely, made sure threshold is only applied to
		proper core revisions. ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch adds disscramble quirk, and it only needs to be enabled at fpga
board on some vendor platforms.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch initializes platform data at pci glue layer, and SoCs x86-based
platform vendor is able to define their flags in platform data at bus glue
layer. Then do some independent behaviors at dwc3 core level.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Some chip vendor is on pre-silicon phase, which needs to use the simulation
board. It should have the same product and vendor id with the true soc, but
might have some minor different configurations.

Below thread discussion proposes to find a method to distinguish between
simulation board and soc.

http://marc.info/?l=linux-usb&m=141194772206369&w=2

In Andvanced Configuration of coreConsultant, there is the parameter of
DWC_USB_EN_FPGA. This bit has the function we need. And it would response as 7
bit of GHWPARAMS6 register. So it's able to check this functional bit to confirm
if works on FPGA board.
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

It enables hibernation if the function is set in coreConsultant.
Suggested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch adds support of the PHY framework for ChipIdea drivers.
Changes are done in both the ChipIdea common code and in the drivers
accessing the PHY. This is done by adding a new PHY member in
ChipIdea's structures and by taking care of it in the code.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch modify the generic code handling PHYs to allow them to be
supplied from the drivers. This adds checks to ensure no PHY was already
there when looking for one in the generic code. This also makes sure we
do not modify its state in the generic HCD functions, it was provided by
the driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch adds support of the PHY framework in OTG and keeps the USB
PHY compatibility. Here the only modification is to add PHY member in
the OTG structure, along with the USB PHY one.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch prepares the introduction of the generic PHY support in the
USB OTG common functions. The USB PHY member of the OTG structure is
renamed to 'usb_phy' and modifications are done in all drivers accessing
it. Renaming this pointer will allow to keep the compatibility for USB
PHY drivers.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Before using the PHY framework instead of the USB PHY one, we need to
move the OTG state into another place, since it won't be available when
USB PHY isn't used. This patch moves the OTG state into the OTG
structure, and makes all the needed modifications in the drivers
using the OTG state.

[ balbi@ti.com : fix build regressions with phy-tahvo.c, musb_dsps.c,
		phy-isp1301-omap, and chipidea's debug.c ]
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

drivers/usb/gadget/udc/r8a66597-udc.c:1849:1-3: WARNING: PTR_ERR_OR_ZERO can be used

 Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR

Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Added failure check for usb_assign_descriptors call in bind function.
Acked-By: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Pavitrakumar Managutte <pavitra1729@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

In commit 0ec8fd70 ("USB: musb: fix possible panic while resuming")
musb_resume() became musb_resume_early() in order to enable the clocks
early on resume. This piece of the resume code was removed later in
commit 03491761 ("usb: musb: move clock handling to glue layer").
In between the function was renamed from musb_resume_early() to
musb_resume_noirq() by commit commit 48fea965 ("USB: Rework musb
suspend()/resume_early()").

Now I see that first musb_core is resumed followed by phy and glue
layer and I ask myself is this really what we intend to do? This kind
of revoked the purpose of the first commit (0ec8fd70).
Because of this and because it looks wrong to resume (core) before the
glue layer I push it to the ->resume callback.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch moves calls to phy enable/disable out of spinlock protected
blocks in device suspend/resume to fix incorrect caller context. Phy
related functions must not be called from atomic context. To protect
device internal state from a race during suspend, a call to
s3c_hsotg_core_disconnect() is added under a spinlock, what prevents any
further activity on the usb bus.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch moves udc initialization from pullup() method to
s3c_hsotg_udc_start(), so that method ends with hardware fully
initialized and left in soft-disconnected state. After this change, the
pullup() method simply clears soft-disconnect start() when called with
is_on=1. For completeness, a call to s3c_hsotg_core_disconnect() has
been added when pullup() method is called with is_on=0, what puts the
udc hardware back to soft-disconnected state.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch moves phy enable/disable calls from pullup() method to
udc_start/stop functions. This solves the issue related to limited caller
context for PHY functions, because they cannot be called from non-sleeping
context. This is also a preparation for using soft-disconnect feature of
udc controller in pullup() method.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch changes s3c_hsotg_core_init function to leave hardware in
soft disconnect mode, so the moment of coupling the hardware to the usb
bus can be later controlled by the separate functions for enabling and
disabling soft disconnect mode. This patch is a preparation to rework
pullup() method.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch removes duplicated code and sets last_rst variable in the
function which does the hardware reset.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Sanity check on resource happening with devm_ioremap_resource().
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Sanity check on resource happening with devm_ioremap_resource().
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Sanity check on resource happening with devm_ioremap_resource().
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Sanity check on resource happening with devm_ioremap_resource().
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Sanity check on resource happening with devm_ioremap_resource().
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The OMAP2+ MUSB glue layer still uses a bare number for the DEVCTL.B-Device bit
in one place, while there's #define MUSB_DEVCTL_BDEVICE for that.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

that call is completely unnecessary because
usb_del_gadget_udc() already makes sure the
gadget driver is properly unregistered from
the UDC.
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>

that call is completely unnecessary because
usb_del_gadget_udc() already makes sure the
gadget driver is properly unregistered from
the UDC.
Signed-off-by: Felipe Balbi <balbi@ti.com>

that call is completely unnecessary because
usb_del_gadget_udc() already makes sure the
gadget driver is properly unregistered from
the UDC.
Signed-off-by: Felipe Balbi <balbi@ti.com>

that call is completely unnecessary because
usb_del_gadget_udc() already makes sure the
gadget driver is properly unregistered from
the UDC.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

As the udc clock controls both the output signals and the internal IP,
it must be enabled before any UDC register is touched.

The bug is revealed when the clock framework disables the clock for a
couple of milliseconds during the boot sequence, and the endpoint
configuration is lost. The bug is hidden when clock framework is not
used, because no "unused clocks disable" occurs.

This patch fixes the wrong behaviour by ensuring that :
 - whenever a UDC register is read or written, the clock is enabled
 - reworks the endpoints programming to have it done under running clock
 - reworks suspend/resume to ensure the same thing
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Use devm_* helpers in the probe function to simplify the error path and
the remove path.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add documentation for device-tree binding of arm PXA 27x udc (usb
device) driver.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: devicetree@vger.kernel.org
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

No functional changes, just adding a prefix
which should have been there from the start.
Signed-off-by: Felipe Balbi <balbi@ti.com>

now that no UDC driver relies on the extra
'driver' argument to ->udc_stop(), we can
safely remove it.

This commit is based on previous work by
Robert Baldyga <r.baldyga@samsung.com> which
can be found at [1]; however that patch turned
out to have a high probability of regressing
many UDC drivers because of a blind search & replace
s/driver/$udc->driver/ which caused the 'driver'
argument to stop_activity() to be a valid non-NULL
pointer when it should be NULL, thus causing UDCs
to mistakenly call gadget driver's ->disconnect()
callback.

[1] http://markmail.org/message/x5zneg4xea4zntabAcked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Currently, we're printing gadget driver name when
registering and UDC name when unregistering. Standardize
on always printing gadget driver name.
Signed-off-by: Felipe Balbi <balbi@ti.com>

now that we provide generic register/unregister
debugging messages from udc-core, we can remove
the same messages from this driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>

now that we provide generic register/unregister
debugging messages from udc-core, we can remove
the same messages from this driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>