- 29 Mar, 2017 40 commits
-
-
Jisheng Zhang authored
RGMII_RXID and RGMII_TX_ID share the same GMAC CTRL setting as RGMII or RGMII_ID. Signed-off-by:
Jisheng Zhang <jszhang@marvell.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Philippe Reynes authored
The ethtool api {get|set}_settings is deprecated. We move this driver to new api {get|set}_link_ksettings. Signed-off-by:Philippe Reynes <tremyfr@gmail.com> Reviewed-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linuxDavid S. Miller authored
Or Gerlitz says: ==================== mlx5e-pedit 2017-03-28 This series adds support for offloading modifications of packet headers using ConnectX-5 HW header re-write as an action applied during packet steering. The offloaded SW mechanism is TC's pedit action. The offloading is supported for E-Switch steering of VF traffic in the SRIOV switchdev mode and for NIC (non eswitch) RX. One use-case for this offload on virtual networks, is when the hypervisor implements flow based router such as Open-Stack's DVR, where L2 headers of guest packets re-written with routers' MAC addresses and the IP TTL is decremented. Another use case (which can be applied in parallel with routing) is stateless NAT where guest L3/L4 headers are re-written. The series is built as follows: the 1st six patches are preperations which don't yet add new functionality, patches 7-8 add the FW APIs (data-structures and commands) for header re-write, and patch nine allows offloading driver to access pedit keys. The 10th patch is somehow the core of the series, where we translate from the pedit way to represent set of header modification elements to the FW API for that same matter. Once a set of HW modification is established, we register it with the FW and get a modify header ID. When this ID is used with an action during packet steering, the HW applies the header modification on the packet. Patches 11 and 12 implement the above logic as an offload for pedit action for the NIC and E-Switch use-cases. I'd like to thanks Elijah Shakkour <elijahs@mellanox.com> for implementing and helping me testing this functionality on HW simulator, before it could be done with FW. ==================== Signed-off-by: -
David Ahern authored
A recent commit skips nexthops in a route if the device has been deleted. Update lfib_nlmsg_size accordingly. Reported-by:
Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by:
David Ahern <dsa@cumulusnetworks.com> Acked-by:
Robert Shearman <rshearma@brocade.com> Signed-off-by:
-
Florian Fainelli authored
mdio-boardinfo contains code that is helpful for platforms to register specific MDIO bus devices independent of how CONFIG_MDIO_DEVICE or CONFIG_PHYLIB will be selected (modular or built-in). In order to make that possible, let's do the following: - descend into drivers/net/phy/ unconditionally - make mdiobus_setup_mdiodev_from_board_info() take a callback argument which allows us not to expose the internal MDIO board info list and mutex, yet maintain the logic within the same file - relocate the code that creates a MDIO device into drivers/net/phy/mdio_bus.c - build mdio-boardinfo.o into the kernel as soon as MDIO_DEVICE is defined (y or m) Fixes: 90eff909 ("net: phy: Allow splitting MDIO bus/device support from PHYs") Fixes: 648ea013 ("net: phy: Allow pre-declaration of MDIO devices") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Tested-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
David S. Miller authored
Andrew Lunn says: ==================== break include loop and dsa devlink support These two patches add very basic support for devlink to DSA, in preparation for playing with dpipe. The first patch is needed to break an include loop between netdevice.h, dsa.h and devlink.h. We need to remove dsa.h from netdevice.h. As a result, some files fail to compile, because they require includes pulled in via dsa.h. So this patch adds a number of includes in various places. The majority is within the network subsystem, but cifs also needs a few fixes. 0-day has been chewing on this for over a day now, and not found any breakage. But Arnd's randconfig might uncover something. ==================== Signed-off-by: -
Andrew Lunn authored
Register the switch and its ports with devlink. Signed-off-by:
-
Andrew Lunn authored
There is an include loop between netdevice.h, dsa.h, devlink.h because of NETDEV_ALIGN, making it impossible to use devlink structures in dsa.h. Break this loop by taking dsa.h out of netdevice.h, add a forward declaration of dsa_switch_tree and netdev_set_default_ethtool_ops() function, which is what netdevice.h requires. No longer having dsa.h in netdevice.h means the includes in dsa.h no longer get included. This breaks a few other files which depend on these includes. Add these directly in the affected file. Signed-off-by:
-
David S. Miller authored
David Ahern says: ==================== netconf: Add support for RTM_DELNETCONF netconf notifications are sent as devices register but not when they are deleted leaving userspace caches out of sync. Add support for RTM_DELNETCONF to ipv4, ipv6 and mpls. MPLS is missing RTM_NEWNETCONF as devices are created, so add it as well. ==================== Signed-off-by: -
David Ahern authored
Send netconf notifications for MPLS when the device registers and unregisters. Signed-off-by:
-
David Ahern authored
Refactor mpls_netconf_notify_devconf to take the event as an input arg. Signed-off-by:
-
David Ahern authored
Send RTM_DELNETCONF notifications when a device is deleted. The message only needs the device index, so modify inet6_netconf_fill_devconf to skip devconf references if it is NULL. Allows a userspace cache to remove entries as devices are deleted. Signed-off-by:
-
David Ahern authored
Refactor inet6_netconf_notify_devconf to take the event as an input arg. Signed-off-by:
-
David Ahern authored
Send RTM_DELNETCONF notifications when a device is deleted. The message only needs the device index, so modify inet_netconf_fill_devconf to skip devconf references if it is NULL. Allows a userspace cache to remove entries as devices are deleted. Signed-off-by:
-
David Ahern authored
Refactor inet_netconf_notify_devconf to take the event as an input arg. Signed-off-by:
-
David Ahern authored
Signed-off-by:
-
Prasad Kanneganti authored
Refactor interrupt moderation code for flexibility because parameters are different for 10G and 25G cards. Currently parameters (for 10G only) come from macros compiled-in to the PF and VF drivers; fix it so that parameters suitable for the card (10G or 25G) come from the NIC firmware via response to a command. Also bump up driver version to 1.5.1 to match newer NIC firmware version. Signed-off-by:
Prasad Kanneganti <prasad.kanneganti@cavium.com> Signed-off-by:
Felix Manlunas <felix.manlunas@cavium.com> Signed-off-by:
Derek Chickles <derek.chickles@cavium.com> Signed-off-by:
-
Vivien Didelot authored
I do not hold the copyright of the DSA core and drivers source files, since these changes have been written as an initiative of my day job. Fix this. Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by:
-
Vivien Didelot authored
Set the trunk member of the mv88e6xxx_atu_entry structure regardless its value, so that uninitialized structures gets the correct boolean value. Note that no mainline code is affected by the current behavior. Signed-off-by:
-
Vlad Yasevich authored
This patch adds support for NETDEV_RESEND_IGMP event similar to how it works for IPv4. Signed-off-by:
Vladislav Yasevich <vyasevic@redhat.com> Signed-off-by:
-
David S. Miller authored
Vivien Didelot says: ==================== net: dsa: fix chip definitions The definitions of some of the mv88e6xxx_ops and mv88e6xxx_info structures are misordered and erroneous for 88E6191 and 88E6391. This patch series cleans that up. ==================== Signed-off-by: -
Vivien Didelot authored
We don't support 88E6391 anywhere in the code, so remove the unused mv88e6391_ops structure. Signed-off-by:
-
Vivien Didelot authored
The mv88e6xxx_info structure for the 88E6191 chip was pointing the mv88e6391_ops definition instead of mv88e6191_ops. Fix this. Signed-off-by:
-
Vivien Didelot authored
The related mv88e6xxx_ops structure was misplaced. Reorder it correctly to fix this. Signed-off-by:
-
Vivien Didelot authored
The related mv88e6xxx_ops and mv88e6xxx_info structure were misplaced. Reorder them correctly to fix this. Signed-off-by:
-
David S. Miller authored
Yuval Mintz says: ==================== qed: load/unload mfw series This series correct the unload flow and greatly enhances its initialization flow in regard to interactions between driver and management firmware. Patch #1 makes sure unloading is done under management-firmware's 'criticial section' protection. Patches #2 - #4 move driver into using a newer scheme for loading in regard to the MFW; This newer scheme would help cleaning the device in case a previous instance has dirtied it [preboot, PDA, etc.]. Patches #5 - #6 let driver inform management-firmware on number of resources which are dependent on the non-management firmware used. Patch #7 then uses a new resource [BDQ] instead of some set value. ==================== Signed-off-by: -
Mintz, Yuval authored
Until now, qed used some port-defined value as BDQ index for both iSCSI and FCoE. As management firmware now treats BDQ as a resource and tells each PF its BDQ-range, start using a valure from that range instead. Signed-off-by:
Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by:
-
Tomer Tayar authored
Management firmware is used as an arbiter between the various PFs in matters of resources, but some of the resources that need to be divided are dependent on the non-management firmware used, so management firmware first needs to be told how many resources there are before trying to divide them. As part of the initialization sequence, driver would first inform the management firmware of the available resources under a dedicated resource lock, and afterwards request for various resources which might be based on the previous set values. Signed-off-by:
Tomer Tayar <Tomer.Tayar@cavium.com> Signed-off-by:
-
Tomer Tayar authored
Global locking can't properly be used to synchronize between different PFs in all scenarios, as those instances might reside in different logical partitions [e.g., when a PF is assigned via PDA to some VM]. The management firmware provides a generic infrastructure for device locks. For each 'resource', it's guaranteed it could be acquired by at most a single PF at any given time [or by management firmware]. This patch adds the necessary logic in qed for utilizing said infrastructure, implementing lock/unlock internal APIs. Signed-off-by:
-
Mintz, Yuval authored
During HW initialization, driver would set various registers to their needed values - but it assumes all registers start at their reset-value, so there's no need to re-configure a register's default value. This assumption might be incorrect, e.g., in case of preboot driver running and initializing the driver prior to our driver. To overcome this, we now ask management firmware to initiate a PF-flr early during the initialization sequence. That would return everything in the PF's scope back to default and prevent previous configurations from still being applied. Signed-off-by:
-
Tomer Tayar authored
Management firmware is used as an arbiter between the various PFs in regard to loading - it causes the various PFs to load/unload sequentially and informs each of its appropriate rule in the init. But the existing flow is too weak to handle some scenarios where PFs aren't properly cleaned prior to loading. The significant scenarios falling under this criteria: a. Preboot drivers in some environment can't properly unload. b. Unexpected driver replacement [kdump, PDA]. Modern management firmware supports a more intricate loading flow, where the driver has the ability to overcome previous limitations. This moves qed into using this newer scheme. Notice new scheme is backward compatible, so new drivers would still be able to load properly on top of older management firmwares and vice versa. Signed-off-by:
-
Mintz, Yuval authored
We'll soon need additional information, so start by changing the infrastructure to receive the initializing variables via a parameter struct. Signed-off-by:
-
Tomer Tayar authored
Management firmware is used as arbiter between different PFs which are loading/unloading, but in order to use the synchronization it offers the contending configurations need to be applied either between their LOAD_REQ <-> LOAD_DONE or UNLOAD_REQ <-> UNLOAD_DONE management firmware commands. Existing HW stop flow utilizes 2 different functions: qed_hw_stop() and qed_hw_reset() which don't abide this requirement; Most of the closure is doing outside the scope of the unload request. This patch removes qed_hw_reset() and places the relevant stop functionality underneath the management firmware protection. Signed-off-by:
-
David S. Miller authored
Parthasarathy Bhuvaragan says: ==================== tipc: subscription refcount simplifications The first patch makes the subscription refcount cleanup lockless and the second updates the subscription refcount policy. ==================== Signed-off-by: -
Ying Xue authored
When a new subscription object is inserted into name_seq->subscriptions list, it's under name_seq->lock protection; when a subscription is deleted from the list, it's also under the same lock protection; similarly, when accessing a subscription by going through subscriptions list, the entire process is also protected by the name_seq->lock. Therefore, if subscription refcount is increased before it's inserted into subscriptions list, and its refcount is decreased after it's deleted from the list, it will be unnecessary to hold refcount at all before accessing subscription object which is obtained by going through subscriptions list under name_seq->lock protection. Signed-off-by:
Ying Xue <ying.xue@windriver.com> Reviewed-by:
Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
-
Ying Xue authored
After a subscription object is created, it's inserted into its subscriber subscrp_list list under subscriber lock protection, similarly, before it's destroyed, it should be first removed from its subscriber->subscrp_list. Since the subscription list is accessed with subscriber lock, all the subscriptions are valid during the lock duration. Hence in tipc_subscrb_subscrp_delete(), we remove subscription get/put and the extra subscriber unlock/lock. After this change, the subscriptions refcount cleanup is very simple and does not access any lock. Acked-by:
Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Signed-off-by:
-
Arnd Bergmann authored
A driver must not access the two fields directly but should instead use the helper functions to set the values and keep a consistent internal state: ethernet/stmicro/stmmac/stmmac_main.c: In function 'stmmac_dvr_probe': ethernet/stmicro/stmmac/stmmac_main.c:4083:8: error: 'struct net_device' has no member named 'real_num_rx_queues'; did you mean 'real_num_tx_queues'? Fixes: a8f5102a ("net: stmmac: TX and RX queue priority configuration") Signed-off-by:
-
Bjorn Andersson authored
With the RPM driver transitioned to RPMSG we can reuse the SMD-RPM driver ontop of GLINK for 8996, without any modifications. Acked-by:
Andy Gross <andy.gross@linaro.org> Signed-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by:
-
Bjorn Andersson authored
Remove the standalone SMD implementation as we have transitioned the client drivers to use the RPMSG based one. Also remove all dependencies on QCOM_SMD from Kconfig files, in order to keep them selectable in the absence of the removed symbol. Acked-by:
-
Bjorn Andersson authored
By moving these client drivers to use RPMSG instead of the direct SMD API we can reuse them ontop of the newly added GLINK wire-protocol support found in the 820 and 835 Qualcomm platforms. As the new (RPMSG-based) and old SMD implementations are mutually exclusive we have to change all client drivers in one commit, to make sure we have a working system before and after this transition. Acked-by:
Kalle Valo <kvalo@codeaurora.org> Acked-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
