This patch changes the initial delay before the startup of a newly
scheduled isochronous stream.  Currently the stream doesn't start
for at least 5 ms (40 microframes).  This value is just an estimate;
it has no real justification.

Instead, we can start the stream as soon as possible after the
scheduling computations are complete.  Essentially this requires
nothing more than reading the frame counter after the stream is
scheduled, instead of before.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch continues the scheduling changes in ehci-hcd by adding a
table to store the bandwidth allocation below each TT.  This will
speed up the scheduling code, as it will no longer need to read
through the entire schedule to compute the bandwidth currently in use.

Properly speaking, the FS/LS budget calculations should be done in
terms of full-speed bytes per microframe, as described in the USB-2
spec.  However the driver currently uses microseconds per microframe,
and the scheduling code isn't robust enough at this point to change
over.  For the time being, we leave the calculations as they are.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 476e4bf9.

Manjunath is no longer at Linaro, the email address bounces.  Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.

I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>

This reverts commit 056ca85d.

Manjunath is no longer at Linaro, the email address bounces.  Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.

I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>

This reverts commit 19d33943.

Manjunath is no longer at Linaro, the email address bounces.  Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.

I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>

This reverts commit 86a63f10.

Manjunath is no longer at Linaro, the email address bounces.  Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.

I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>

This reverts commit 018258b4.

Manjunath is no longer at Linaro, the email address bounces.  Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.

I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>

This reverts commit fea0896f.

Manjunath is no longer at Linaro, the email address bounces.  Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.

I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>

This reverts commit 36a87587.

Manjunath is no longer at Linaro, the email address bounces.  Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.

I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>

Signed-off-by: Matthias Beyer <mail@beyermatthias.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Matthias Beyer <mail@beyermatthias.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

including:

- removing of trailing whitespace
- removing spaces before array indexing (foo [] to foo[])
- reindention of a switch-case block
- spaces to tabs
Signed-off-by: Matthias Beyer <mail@beyermatthias.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure to return errors from tiocmget rather than rely on
uninitialised stack data.

Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Export usb_serial_generic_write_start which is needed when implementing
a custom resume function while still relying on the generic write
implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add memory-flags parameter to usb_serial_generic_write_start which is
called from write, resume and completion handler, all with different
allocation requirements.

Note that by using the memory flag to determine when called from the
completion handler, everything will work as before even if the
completion handler is run with interrupts enabled (as suggested).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Clean up some comments, drop excessive comments and fix-up style.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The DECLARE_BITMAP macro should be used for declaring this bitmap.
This commit converts the busmap from a struct to a simple (static)
bitmap, using the DECLARE_BITMAP macro from linux/types.h.

Please review, as I'm new to kernel development, I don't know if this
has any hidden side effects!

Suggested by joe@perches.com
Signed-off-by: Matthias Beyer <mail@beyermatthias.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently, Samsung is using 'EXYNOS' as the name of Samsung SoCs.
Thus, ehci-exynos is preferred than ehci-s5p.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The non-DT for EXYNOS SoCs is not supported from v3.11.
Thus, there is no need to support non-DT for Exynos EHCI driver.

The 'include/linux/platform_data/usb-ehci-s5p.h' file has been
used for non-DT support. Thus, the 'usb-ehci-s5p.h' file can
be removed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since commit ca914350 "ARM: EXYNOS: Remove unused board files",
s5p_device_ehci is not used anymore. Thus, s5p_device_ehci can
be removed. Also, unnecessary S5P_DEV_USB_EHCI option is removed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For improved scheduling of transfers through a Transaction Translator,
ehci-hcd will need to store a bunch of information associated with the
FS/LS bus on the downstream side of the TT.  This patch adds a pointer
for such HCD-private data to the usb_tt structure.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch significantly changes the scheduling code in ehci-hcd.
Instead of calculating the current bandwidth utilization by trudging
through the schedule and adding up the times used by the existing
transfers, we will now maintain a table holding the time used for each
of 64 microframes.  This will drastically speed up the bandwidth
computations.

In addition, it eliminates a theoretical bug.  An isochronous endpoint
may have bandwidth reserved even at times when it has no transfers
listed in the schedule.  The table will keep track of the reserved
bandwidth, whereas adding up entries in the schedule would miss it.

As a corollary, we can keep bandwidth reserved for endpoints even
when they aren't in active use.  Eventually the bandwidth will be
reserved when a new alternate setting is installed; for now the
endpoint's reservation takes place when its first URB is submitted.

A drawback of this approach is that transfers with an interval larger
than 64 microframes will have to be charged for bandwidth as though
the interval was 64.  In practice this shouldn't matter much;
transfers with longer intervals tend to be rather short anyway (things
like hubs or HID devices).

Another minor drawback is that we will keep track of two different
period and phase values: the actual ones and the ones used for
bandwidth allocation (which are limited to 64).  This adds only a
small amount of overhead: 3 bytes for each endpoint.

The patch also adds a new debugfs file named "bandwidth" to display
the information stored in the new table.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch begins the process of unifying the scheduling parameters
that ehci-hcd uses for interrupt and isochronous transfers.  It
creates an ehci_per_sched structure, which will be stored in both
ehci_qh and ehci_iso_stream structures, and will contain the common
scheduling information needed for both.

Initially we merely create the new structure and move some existing
fields into it.  Later patches will add more fields and utilize these
structures in improved scheduling algorithms.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ehci-hcd is inconsistent in the sentinel values it uses to indicate
that no frame number has been assigned for a periodic transfer.  Some
places it uses NO_FRAME (defined as 65535), other places it uses -1,
and elsewhere it uses 9999.

This patch defines a value for NO_FRAME which can fit in a 16-bit
signed integer, and changes the code to use it everywhere.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ehci-hcd uses a value of 0 in an endpoint's toggle flag to indicate
that the endpoint has been reset (and therefore the Data Toggle bit
needs to be cleared in the endpoint's QH overlay region).

The toggle flag should be set to 0 only when ehci_endpoint_reset()
succeeds.  This patch moves the usb_settoggle() call into the
appropriate branch of the "if" statement.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The scheduling code in ehci-hcd contains an error.  For full-speed
isochronous-OUT transfers, the EHCI spec forbids scheduling
Start-Split transactions in H-microframe 7, but the driver allows it
anyway.  This patch adds a check to prevent it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Although the bandwidth statistics maintained by ehci-hcd show up only
in the /sys/kernel/debug/usb/devices file, they ought to be calculated
correctly.  The calculation for full-speed isochronous endpoints is
wrong; it mistakenly yields bytes per microframe instead of bytes per
frame.  The "interval" value, which is in frames, should not be
converted to microframes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The check_intr_schedule() routine in ehci-hcd looks at the wrong
microframes when checking to see if a full-speed or low-speed
interrupt endpoint will fit in the periodic schedule.  If the
Start-Split transaction is scheduled for microframe N then the
Complete-Split transactions get scheduled for microframes N+2, N+3, and
N+4.  However the code considers N+1, N+2, and N+3 instead.

This patch fixes the limits on the "for" loop and also improves the
use of whitespace.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Host controller drivers use the NS_TO_US macro to convert transaction
times, which are computed in nanoseconds, to microseconds for
scheduling.  Periodic scheduling requires worst-case estimates, but
the macro does its conversion using round-to-nearest.  This patch
changes it to use round-up, giving a correct worst-case value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb_wait_anchor_empty_timeout() should wait till the completion handler
has run. Both the zd1211rw driver and the uas driver (in its task mgmt) depend
on the completion handler having completed when usb_wait_anchor_empty_timeout()
returns, as they read state set by the completion handler after an
usb_wait_anchor_empty_timeout() call.

But __usb_hcd_giveback_urb() calls usb_unanchor_urb before calling the
completion handler. This is necessary as the completion handler may
re-submit and re-anchor the urb. But this introduces a race where the state
these drivers want to read has not been set yet by the completion handler
(this race is easily triggered with the uas task mgmt code).

I've considered adding an anchor_count to struct urb, which would be
incremented on anchor and decremented on unanchor, and then only actually
do the anchor / unanchor on 0 -> 1 and 1 -> 0 transtions, combined with
moving the unanchor call in hcd_giveback_urb to after calling the completion
handler. But this will only work if urb's are only re-anchored to the same
anchor as they were anchored to before the completion handler ran.

And at least one driver re-anchors to another anchor from the completion
handler (rtlwifi).

So I have come up with this patch instead, which adds the ability to
suspend wakeups of usb_wait_anchor_empty_timeout() waiters to the usb_anchor
functionality, and uses this in __usb_hcd_giveback_urb() to delay wake-ups
until the completion handler has run.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

And do so in a way which ensures that any fields added in the future will
also get properly zero-ed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When devm_usb_get_phy() fails, usb_put_hcd() should be called
to prevent memory leak.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Allows MSM EHCI controller to be specified via device tree.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use struct usb_hcd::phy to hold USB PHY instance.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These aren't necessary after switch and if blocks.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixing the below dump:

root@freescale ~$ modprobe g_serial
g_serial gadget: Gadget Serial v2.4
g_serial gadget: g_serial ready
BUG: sleeping function called from invalid context at /home/b29397/work/projects/upstream/usb/usb/drivers/base/power/runtime.c:952
in_atomic(): 1, irqs_disabled(): 128, pid: 805, name: modprobe
2 locks held by modprobe/805:
 #0:  (udc_lock){+.+.+.}, at: [<7f000a74>] usb_gadget_probe_driver+0x44/0xb4 [udc_core]
 #1:  (&(&ci->lock)->rlock){......}, at: [<7f033488>] ci_udc_start+0x94/0x110 [ci_hdrc]
irq event stamp: 3878
hardirqs last  enabled at (3877): [<806b6720>] _raw_spin_unlock_irqrestore+0x40/0x6c
hardirqs last disabled at (3878): [<806b6474>] _raw_spin_lock_irqsave+0x2c/0xa8
softirqs last  enabled at (3872): [<8002ec0c>] __do_softirq+0x1c8/0x2e8
softirqs last disabled at (3857): [<8002f180>] irq_exit+0xbc/0x110
CPU: 0 PID: 805 Comm: modprobe Not tainted 3.11.0-next-20130910+ #85
[<80016b94>] (unwind_backtrace+0x0/0xf8) from [<80012e0c>] (show_stack+0x20/0x24)
[<80012e0c>] (show_stack+0x20/0x24) from [<806af554>] (dump_stack+0x9c/0xc4)
[<806af554>] (dump_stack+0x9c/0xc4) from [<8005940c>] (__might_sleep+0xf4/0x134)
[<8005940c>] (__might_sleep+0xf4/0x134) from [<803a04a4>] (__pm_runtime_resume+0x94/0xa0)
[<803a04a4>] (__pm_runtime_resume+0x94/0xa0) from [<7f0334a4>] (ci_udc_start+0xb0/0x110 [ci_hdrc])
[<7f0334a4>] (ci_udc_start+0xb0/0x110 [ci_hdrc]) from [<7f0009b4>] (udc_bind_to_driver+0x5c/0xd8 [udc_core])
[<7f0009b4>] (udc_bind_to_driver+0x5c/0xd8 [udc_core]) from [<7f000ab0>] (usb_gadget_probe_driver+0x80/0xb4 [udc_core])
[<7f000ab0>] (usb_gadget_probe_driver+0x80/0xb4 [udc_core]) from [<7f008618>] (usb_composite_probe+0xac/0xd8 [libcomposite])
[<7f008618>] (usb_composite_probe+0xac/0xd8 [libcomposite]) from [<7f04b168>] (init+0x8c/0xb4 [g_serial])
[<7f04b168>] (init+0x8c/0xb4 [g_serial]) from [<800088e8>] (do_one_initcall+0x108/0x16c)
[<800088e8>] (do_one_initcall+0x108/0x16c) from [<8008e518>] (load_module+0x1b00/0x20a4)
[<8008e518>] (load_module+0x1b00/0x20a4) from [<8008eba8>] (SyS_init_module+0xec/0x100)
[<8008eba8>] (SyS_init_module+0xec/0x100) from [<8000ec40>] (ret_fast_syscall+0x0/0x48)
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

After configuration, the host also possible sends bus reset
at any time, at such situation, it will trigger below spinlock
recursion dump. This commit unlocks the spinlock before calling
gadget's disconnect.

BUG: spinlock recursion on CPU#0, swapper/0/0
 lock: 0xbf128014, .magic: dead4ead, .owner: swapper/0/0, .owner_cpu: 0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.11.0-next-20130910+ #106
[<80014e20>] (unwind_backtrace+0x0/0xec) from [<80011a6c>] (show_stack+0x10/0x14)
[<80011a6c>] (show_stack+0x10/0x14) from [<805c143c>] (dump_stack+0x94/0xbc)
[<805c143c>] (dump_stack+0x94/0xbc) from [<80282cf8>] (do_raw_spin_lock+0x16c/0x18c)
[<80282cf8>] (do_raw_spin_lock+0x16c/0x18c) from [<805c77e0>] (_raw_spin_lock_irqsave+0x50/0x5c)
[<805c77e0>] (_raw_spin_lock_irqsave+0x50/0x5c) from [<803cff88>] (ep_disable+0x24/0x110)
[<803cff88>] (ep_disable+0x24/0x110) from [<7f015d50>] (gserial_disconnect+0xa0/0x15c [u_serial])
[<7f015d50>] (gserial_disconnect+0xa0/0x15c [u_serial]) from [<7f01c06c>] (acm_disable+0xc/0x30 [usb_f_acm])
[<7f01c06c>] (acm_disable+0xc/0x30 [usb_f_acm]) from [<7f001478>] (reset_config.isra.10+0x34/0x5c [libcomposite])
[<7f001478>] (reset_config.isra.10+0x34/0x5c [libcomposite]) from [<7f0014d4>] (composite_disconnect+0x34/0x5c [libcomposite])
[<7f0014d4>] (composite_disconnect+0x34/0x5c [libcomposite]) from [<803d1024>] (udc_irq+0x770/0xce4)
[<803d1024>] (udc_irq+0x770/0xce4) from [<803cdcc0>] (ci_irq+0x98/0x164)
[<803cdcc0>] (ci_irq+0x98/0x164) from [<8007edfc>] (handle_irq_event_percpu+0x50/0x17c)
[<8007edfc>] (handle_irq_event_percpu+0x50/0x17c) from [<8007ef64>] (handle_irq_event+0x3c/0x5c)
[<8007ef64>] (handle_irq_event+0x3c/0x5c) from [<80081e98>] (handle_fasteoi_irq+0x98/0x168)
[<80081e98>] (handle_fasteoi_irq+0x98/0x168) from [<8007e598>] (generic_handle_irq+0x28/0x3c)
[<8007e598>] (generic_handle_irq+0x28/0x3c) from [<8000edf4>] (handle_IRQ+0x4c/0xb4)
[<8000edf4>] (handle_IRQ+0x4c/0xb4) from [<800085bc>] (gic_handle_irq+0x28/0x5c)
[<800085bc>] (gic_handle_irq+0x28/0x5c) from [<800125c0>] (__irq_svc+0x40/0x54)
Exception stack(0x8083bf68 to 0x8083bfb0)
bf60:                   81533b80 00000000 00096234 8001d760 8088e12c 00000000
bf80: 8083a000 8083a000 8084290c 805cb414 808428ac 8083a000 00000001 8083bfb0
bfa0: 8000f138 8000f13c 60000013 ffffffff
[<800125c0>] (__irq_svc+0x40/0x54) from [<8000f13c>] (arch_cpu_idle+0x30/0x3c)
[<8000f13c>] (arch_cpu_idle+0x30/0x3c) from [<8005eb94>] (cpu_startup_entry+0xf4/0x148)
[<8005eb94>] (cpu_startup_entry+0xf4/0x148) from [<807f1a2c>] (start_kernel+0x2c4/0x318)
BUG: spinlock lockup suspected on CPU#0, swapper/0/0
 lock: 0xbf128014, .magic: dead4ead, .owner: swapper/0/0, .owner_cpu: 0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.11.0-next-20130910+ #106
[<80014e20>] (unwind_backtrace+0x0/0xec) from [<80011a6c>] (show_stack+0x10/0x14)
[<80011a6c>] (show_stack+0x10/0x14) from [<805c143c>] (dump_stack+0x94/0xbc)
[<805c143c>] (dump_stack+0x94/0xbc) from [<80282c94>] (do_raw_spin_lock+0x108/0x18c)
[<80282c94>] (do_raw_spin_lock+0x108/0x18c) from [<805c77e0>] (_raw_spin_lock_irqsave+0x50/0x5c)
[<805c77e0>] (_raw_spin_lock_irqsave+0x50/0x5c) from [<803cff88>] (ep_disable+0x24/0x110)
[<803cff88>] (ep_disable+0x24/0x110) from [<7f015d50>] (gserial_disconnect+0xa0/0x15c [u_serial])
[<7f015d50>] (gserial_disconnect+0xa0/0x15c [u_serial]) from [<7f01c06c>] (acm_disable+0xc/0x30 [usb_f_acm])
[<7f01c06c>] (acm_disable+0xc/0x30 [usb_f_acm]) from [<7f001478>] (reset_config.isra.10+0x34/0x5c [libcomposite])
[<7f001478>] (reset_config.isra.10+0x34/0x5c [libcomposite]) from [<7f0014d4>] (composite_disconnect+0x34/0x5c [libcomposite])
[<7f0014d4>] (composite_disconnect+0x34/0x5c [libcomposite]) from [<803d1024>] (udc_irq+0x770/0xce4)
[<803d1024>] (udc_irq+0x770/0xce4) from [<803cdcc0>] (ci_irq+0x98/0x164)
[<803cdcc0>] (ci_irq+0x98/0x164) from [<8007edfc>] (handle_irq_event_percpu+0x50/0x17c)
[<8007edfc>] (handle_irq_event_percpu+0x50/0x17c) from [<8007ef64>] (handle_irq_event+0x3c/0x5c)
[<8007ef64>] (handle_irq_event+0x3c/0x5c) from [<80081e98>] (handle_fasteoi_irq+0x98/0x168)
[<80081e98>] (handle_fasteoi_irq+0x98/0x168) from [<8007e598>] (generic_handle_irq+0x28/0x3c)
[<8007e598>] (generic_handle_irq+0x28/0x3c) from [<8000edf4>] (handle_IRQ+0x4c/0xb4)
[<8000edf4>] (handle_IRQ+0x4c/0xb4) from [<800085bc>] (gic_handle_irq+0x28/0x5c)
[<800085bc>] (gic_handle_irq+0x28/0x5c) from [<800125c0>] (__irq_svc+0x40/0x54)
Exception stack(0x8083bf68 to 0x8083bfb0)
bf60:                   81533b80 00000000 00096234 8001d760 8088e12c 00000000
bf80: 8083a000 8083a000 8084290c 805cb414 808428ac 8083a000 00000001 8083bfb0
bfa0: 8000f138 8000f13c 60000013 ffffffff
[<800125c0>] (__irq_svc+0x40/0x54) from [<8000f13c>] (arch_cpu_idle+0x30/0x3c)
[<8000f13c>] (arch_cpu_idle+0x30/0x3c) from [<8005eb94>] (cpu_startup_entry+0xf4/0x148)
[<8005eb94>] (cpu_startup_entry+0xf4/0x148) from [<807f1a2c>] (start_kernel+0x2c4/0x318)
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

"old_rdtodo" and "size" are short type.  They are type promoted to int
and the condition is never true.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In addition to the error statuses -ETIMEDOUT and -EPIPE, uhci_hub_control()
needs to return the length of copied buffer when appropriate, so that the
returned status of ->hub_control() in rh_call_control() in the USB core
HCD can be properly handled.

This patch also removes the OK() macro to make the code more readable.
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch proposes to remove the use of the IRQF_DISABLED flag

It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>