- 25 Jun, 2019 4 commits
-
-
Paolo Valente authored
Until the base value for request service times gets finally computed for a bfq_queue, the inject limit for that queue does depend on the think-time state (short|long) of the queue. A timely update of the think time then guarantees a quicker activation or deactivation of the injection. Fortunately, the think time of a bfq_queue is updated in the same code path as the inject limit; but after the inject limit. This commits moves the update of the think time before the update of the inject limit. For coherence, it moves the update of the seek time too. Reported-by:
Srivatsa S. Bhat (VMware) <srivatsa@csail.mit.edu> Tested-by:
Paolo Valente <paolo.valente@linaro.org> Signed-off-by:
Jens Axboe <axboe@kernel.dk>
-
Paolo Valente authored
I/O injection gets reduced if it increases the request service times of the victim queue beyond a certain threshold. The threshold, in its turn, is computed as a function of the base service time enjoyed by the queue when it undergoes no injection. As a consequence, for injection to work properly, the above base value has to be accurate. In this respect, such a value may vary over time. For example, it varies if the size or the spatial locality of the I/O requests in the queue change. It is then important to update this value whenever possible. This commit performs this update. Reported-by:
-
Paolo Valente authored
One of the cases where the parameters for injection may be updated is when there are no more in-flight I/O requests. The number of in-flight requests is stored in the field bfqd->rq_in_driver of the descriptor bfqd of the device. So, the controlled condition is bfqd->rq_in_driver == 0. Unfortunately, this is wrong because, the instruction that checks this condition is in the code path that handles the completion of a request, and, in particular, the instruction is executed before bfqd->rq_in_driver is decremented in such a code path. This commit fixes this issue by just replacing 0 with 1 in the comparison. Reported-by:
-
Paolo Valente authored
Until the base value of the request service times gets finally computed for a bfq_queue, the inject limit does depend on the think-time state (short|long). The limit must be 0 or 1 if the think time is deemed, respectively, as short or long. However, such a check and possible limit update is performed only periodically, once per second. So, to make the injection mechanism much more reactive, this commit performs the update also every time the think-time state changes. In addition, in the following special case, this commit lets the inject limit of a bfq_queue bfqq remain equal to 1 even if bfqq's think time is short: bfqq's I/O is synchronized with that of some other queue, i.e., bfqq may receive new I/O only after the I/O of the other queue is completed. Keeping the inject limit to 1 allows the blocking I/O to be served while bfqq is in service. And this is very convenient both for bfqq and for the total throughput, as explained in detail in the comments in bfq_update_has_short_ttime(). Reported-by:
-
- 24 Jun, 2019 1 commit
-
-
git://git.infradead.org/nvmeJens Axboe authored
Pull NVMe updates from Christoph: "A large chunk of NVMe updates for 5.3. Highlights: - improved PCIe suspent support (Keith Busch) - error injection support for the admin queue (Akinobu Mita) - Fibre Channel discovery improvements (James Smart) - tracing improvements including nvmetc tracing support (Minwoo Im) - misc fixes and cleanups (Anton Eidelman, Minwoo Im, Chaitanya Kulkarni)" * 'nvme-5.3' of git://git.infradead.org/nvme: (26 commits) Documentation: nvme: add an example for nvme fault injection nvme: enable to inject errors into admin commands nvme: prepare for fault injection into admin commands nvmet: introduce target-side trace nvme-trace: print result and status in hex format nvme-trace: support for fabrics commands in host-side nvme-trace: move opcode symbol print to nvme.h nvme-trace: do not export nvme_trace_disk_name nvme-pci: clean up nvme_remove_dead_ctrl a bit nvme-pci: properly report state change failure in nvme_reset_work nvme-pci: set the errno on ctrl state change error nvme-pci: adjust irq max_vector using num_possible_cpus() nvme-pci: remove queue_count_ops for write_queues and poll_queues nvme-pci: remove unnecessary zero for static var nvme-pci: use host managed power state for suspend nvme: introduce nvme_is_fabrics to check fabrics cmd nvme: export get and set features nvme: fix possible io failures when removing multipathed ns nvme-fc: add message when creating new association lpfc: add sysfs interface to post NVME RSCN ...
-
- 21 Jun, 2019 30 commits
-
-
Akinobu Mita authored
This adds an example of how to inject errors into admin commands. Suggested-by:
Thomas Tai <thomas.tai@oracle.com> Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Reviewed-by:
Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Reviewed-by:
Minwoo Im <minwoo.im@samsung.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Akinobu Mita authored
This enables to inject errors into the commands submitted to the admin queue. It is useful to test error handling in the controller initialization. # echo 100 > /sys/kernel/debug/nvme0/fault_inject/probability # echo 1 > /sys/kernel/debug/nvme0/fault_inject/times # echo 10 > /sys/kernel/debug/nvme0/fault_inject/space # nvme reset /dev/nvme0 # dmesg ... nvme nvme0: Could not set queue count (16385) nvme nvme0: IO queues not created Signed-off-by:
Minwoo Im <minwoo.im.dev@gmail.com> Reviewed-by:
Sagi Grimberg <sagi@grimberg.me> Reviewed-by:
-
Akinobu Mita authored
Currenlty fault injection support for nvme only enables to inject errors into the commands submitted to I/O queues. In preparation for fault injection into the admin commands, this makes the helper functions independent of struct nvme_ns. Signed-off-by:
-
Minwoo Im authored
This patch introduces target-side request tracing. As Christoph suggested, the trace would not be in a core or module to avoid disadvantages like cache miss: http://lists.infradead.org/pipermail/linux-nvme/2019-June/024721.html The target-side trace code is entirely based on the Johannes's trace code from the host side. It has lots of codes duplicated, but it would be better than having advantages mentioned above. It also traces not only fabrics commands, but also nvme normal commands. Once the codes to be shared gets bigger, then we can make it common as suggsted. This also removed the create_sq and create_cq trace parsing functions because it will be done by the connect fabrics command. Example: echo 1 > /sys/kernel/debug/tracing/event/nvmet/nvmet_req_init/enable echo 1 > /sys/kernel/debug/tracing/event/nvmet/nvmet_req_complete/enable cat /sys/kernel/debug/tracing/trace Signed-off-by:
-
Geert Uytterhoeven authored
With gcc 4.1: drivers/lightnvm/core.c: In function ‘nvm_remove_tgt’: drivers/lightnvm/core.c:510: warning: ‘t’ is used uninitialized in this function Indeed, if no NVM devices have been registered, t will be an uninitialized pointer, and may be dereferenced later. A call to nvm_remove_tgt() can be triggered from userspace by issuing the NVM_DEV_REMOVE ioctl on the lightnvm control device. Fix this by preinitializing t to NULL. Fixes: 843f2edb ("lightnvm: do not remove instance under global lock") Signed-off-by:Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
Matias Bjørling <mb@lightnvm.io> Signed-off-by:
-
Heiner Litz authored
bio_add_pc_page() may merge pages when a bio is padded due to a flush. Fix iteration over the bio to free the correct pages in case of a merge. Signed-off-by:
Heiner Litz <hlitz@ucsc.edu> Reviewed-by:
Javier González <javier@javigon.com> Signed-off-by:
-
Minwoo Im authored
The "result" field is in 64bit to be printed out which means it could be like: nvme_complete_rq: nvme0: qid=0, cmdid=0, res=18446612684158962624, etries=0, flags=0x0, status=0 Switch both the result and status field to be printed in hexadecimal format to be easier to read. Signed-off-by:
-
Minwoo Im authored
This patch introduces fabrics commands tracing feature from host-side. This patch does not include any changes for the previous host-side tracing, but just add fabrics commands parsing in cmd=() format. Signed-off-by:
-
Minwoo Im authored
The following patches are going to provide the target-side trace which might need these kind of macros. It would be great if it can be shared between host and target side both. Signed-off-by:
-
Minwoo Im authored
nvme_trace_disk_name() is now already being invoked with the function prototype in trace.h. We don't need to export this symbol at all. The following patches are going to provide target-side trace feature with the exactly same function with this so that this patch removes the EXPORT_SYMBOL() for this function. Signed-off-by:
-
Chaitanya Kulkarni authored
Remove the status parameter o nvme_remove_dead_ctrl(), which is only used for printing it. We move the print message to the same function where actual error is occurring. Signed-off-by:
-
Minwoo Im authored
If the state change to NVME_CTRL_CONNECTING fails, the dmesg is going to be like: [ 293.689160] nvme nvme0: failed to mark controller CONNECTING [ 293.689160] nvme nvme0: Removing after probe failure status: 0 Even it prints the first line to indicate the situation, the second line is not proper because the status is 0 which means normally success of the previous operation. This patch makes it indicate the proper error value when it fails. [ 25.932367] nvme nvme0: failed to mark controller CONNECTING [ 25.932369] nvme nvme0: Removing after probe failure status: -16 This situation is able to be easily reproduced by: root@target:~# rmmod nvme && modprobe nvme && rmmod nvme Signed-off-by:
-
Chaitanya Kulkarni authored
This patch removes the confusing assignment of the variable result at the time of declaration and sets the value in error cases next to the places where the actual error is happening. Here we also set the result value to -ENODEV when we fail at the final ctrl state transition in nvme_reset_work(). Without this assignment result will hold 0 from nvme_setup_io_queue() and on failure 0 will be passed to he nvme_remove_dead_ctrl() from final state transition. Signed-off-by:
-
Minwoo Im authored
If the "irq_queues" are greater than num_possible_cpus(), nvme_calc_irq_sets() can have irq set_size for HCTX_TYPE_DEFAULT greater than it can be afforded. 2039 affd->set_size[HCTX_TYPE_DEFAULT] = nrirqs - nr_read_queues; It might cause a WARN() from the irq_build_affinity_masks() like [1]: 220 if (nr_present < numvecs) 221 WARN_ON(nr_present + nr_others < numvecs); This patch prevents it from the WARN() by adjusting the max_vector value from the nvme_setup_irqs(). [1] WARN messages when modprobe nvme write_queues=32 poll_queues=0: root@target:~/nvme# nproc 8 root@target:~/nvme# modprobe nvme write_queues=32 poll_queues=0 [ 17.925326] nvme nvme0: pci function 0000:00:04.0 [ 17.940601] WARNING: CPU: 3 PID: 1030 at kernel/irq/affinity.c:221 irq_create_affinity_masks+0x222/0x330 [ 17.940602] Modules linked in: nvme nvme_core [last unloaded: nvme] [ 17.940605] CPU: 3 PID: 1030 Comm: kworker/u17:4 Tainted: G W 5.1.0+ #156 [ 17.940605] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014 [ 17.940608] Workqueue: nvme-reset-wq nvme_reset_work [nvme] [ 17.940609] RIP: 0010:irq_create_affinity_masks+0x222/0x330 [ 17.940611] Code: 4c 8d 4c 24 28 4c 8d 44 24 30 e8 c9 fa ff ff 89 44 24 18 e8 c0 38 fa ff 8b 44 24 18 44 8b 54 24 1c 5a 44 01 d0 41 39 c4 76 02 <0f> 0b 48 89 df 44 01 e5 e8 f1 ce 10 00 48 8b 34 24 44 89 f0 44 01 [ 17.940611] RSP: 0018:ffffc90002277c50 EFLAGS: 00010216 [ 17.940612] RAX: 0000000000000008 RBX: ffff88807ca48860 RCX: 0000000000000000 [ 17.940612] RDX: ffff88807bc03800 RSI: 0000000000000020 RDI: 0000000000000000 [ 17.940613] RBP: 0000000000000001 R08: ffffc90002277c78 R09: ffffc90002277c70 [ 17.940613] R10: 0000000000000008 R11: 0000000000000001 R12: 0000000000000020 [ 17.940614] R13: 0000000000025d08 R14: 0000000000000001 R15: ffff88807bc03800 [ 17.940614] FS: 0000000000000000(0000) GS:ffff88807db80000(0000) knlGS:0000000000000000 [ 17.940616] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 17.940617] CR2: 00005635e583f790 CR3: 000000000240a000 CR4: 00000000000006e0 [ 17.940617] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 17.940618] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 17.940618] Call Trace: [ 17.940622] __pci_enable_msix_range+0x215/0x540 [ 17.940623] ? kernfs_put+0x117/0x160 [ 17.940625] pci_alloc_irq_vectors_affinity+0x74/0x110 [ 17.940626] nvme_reset_work+0xc30/0x1397 [nvme] [ 17.940628] ? __switch_to_asm+0x34/0x70 [ 17.940628] ? __switch_to_asm+0x40/0x70 [ 17.940629] ? __switch_to_asm+0x34/0x70 [ 17.940630] ? __switch_to_asm+0x40/0x70 [ 17.940630] ? __switch_to_asm+0x34/0x70 [ 17.940631] ? __switch_to_asm+0x40/0x70 [ 17.940632] ? nvme_irq_check+0x30/0x30 [nvme] [ 17.940633] process_one_work+0x20b/0x3e0 [ 17.940634] worker_thread+0x1f9/0x3d0 [ 17.940635] ? cancel_delayed_work+0xa0/0xa0 [ 17.940636] kthread+0x117/0x120 [ 17.940637] ? kthread_stop+0xf0/0xf0 [ 17.940638] ret_from_fork+0x3a/0x50 [ 17.940639] ---[ end trace aca8a131361cd42a ]--- [ 17.942124] nvme nvme0: 7/1/0 default/read/poll queues Signed-off-by:
-
Minwoo Im authored
queue_count_set() seems like that it has been provided to limit the number of queue entries for write/poll queues. But, the queue_count_set() has been doing nothing but a parameter check even it has num_possible_cpus() which is nop. This patch removes entire queue_count_ops from the write_queues and poll_queues. Signed-off-by:
-
Minwoo Im authored
poll_queues will be zero even without zero initialization here. Signed-off-by:
-
Keith Busch authored
The nvme pci driver prepares its devices for power loss during suspend by shutting down the controllers. The power setting is deferred to pci driver's power management before the platform removes power. The suspend-to-idle mode, however, does not remove power. NVMe devices that implement host managed power settings can achieve lower power and better transition latencies than using generic PCI power settings. Try to use this feature if the platform is not involved with the suspend. If successful, restore the previous power state on resume. Tested-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Tested-by:
Mario Limonciello <mario.limonciello@dell.com> Reviewed-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
Keith Busch <keith.busch@intel.com> Signed-off-by:
-
Minwoo Im authored
This patch introduces a nvme_is_fabrics() inline function to check whether or not the given command structure is for fabrics. Signed-off-by:
-
Keith Busch authored
Future use intends to make use of both, so export these functions. And since their implementation is identical except for the opcode, provide a new function that implement both. [akinobu.mita@gmail.com>: fix line over 80 characters] Signed-off-by:
-
Anton Eidelman authored
When a shared namespace is removed, we call blk_cleanup_queue() when the device can still be accessed as the current path and this can result in submission to a dying queue. Hence, direct_make_request() called by our mpath device may fail (propagating the failure to userspace). Instead, we want to failover this I/O to a different path if one exists. Thus, before we cleanup the request queue, we make sure that the device is cleared from the current path nor it can be selected again as such. Fix this by: - clear the ns from the head->list and synchronize rcu to make sure there is no concurrent path search that restores it as the current path - clear the mpath current path in order to trigger a subsequent path search and sync srcu to wait for any ongoing request submissions - safely continue to namespace removal and blk_cleanup_queue Signed-off-by:
Anton Eidelman <anton@lightbitslabs.com> Signed-off-by:
-
James Smart authored
When looking at console messages to troubleshoot, there are one maybe two messages before creation of the controller is complete. However, a lot of io takes place to reach that point. It's unclear when things have started. Add a message when the controller is attempting to create a new association. Thus we know what controller, between what host and remote port, and what NQN is being put into place for any subsequent success or failure messages. Signed-off-by:
James Smart <jsmart2021@gmail.com> Reviewed-by:
Giridhar Malavali <gmalavali@marvell.com> Signed-off-by:
-
James Smart authored
To support scenarios which aren't bound to nvmetcli add port scenarios, which is currently where the nvmet_fc transport invokes the discovery event callbacks, a syfs attribute is added to lpfc which can be written to cause an RSCN to be generated for the nport. Signed-off-by:
Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by:
Hannes Reinecke <hare@suse.com> Reviewed-by:
Arun Easi <aeasi@marvell.com> Signed-off-by:
-
James Smart authored
This patch updates RSCN receive processing to check for the remote port being an NVME port, and if so, invoke the nvme_fc callback to rescan the remote port. The rescan will generate a discovery udev event. Signed-off-by:
-
James Smart authored
This patch adds support for the nvmet discovery op. When the callback routine is called, the driver will call the routine to generate an RSCN to the port on the other end of the link. Signed-off-by:
-
James Smart authored
This patch adds general RSCN support: - The ability to transmit an RSCN to the port on the other end of the link (regular port if pt2pt, or fabric controller if fabric). - And general recognition of an RSCN ELS when an ELS is received. Signed-off-by:
-
James Smart authored
Update fcloop to support the discovery_event operation and invoke a nvme rescan. In a real fc adapter, this would generate an RSCN, which the host would receive and convert into a nvme rescan on the remote port specified in the rscn payload. Signed-off-by:
-
James Smart authored
This patch adds support for the nvmet discovery_change transport op. In turn, the transport adds it's own LLDD api callback discovery_event op to request the LLDD to generate an RSCN for the discovery change. Signed-off-by:
-
James Smart authored
Some transports, such as FC-NVME, support discovery controller change events without the use of a persistent discovery controller. FC receives events via RSCN from the FC Fabric Controller or subsystem FC port. This patch adds a nvmet transport op that is called whenever a discovery change event occurs in the nvmet layer. To facilitate the callback without adding another layer to cross into core.c to reference the transport ops, the port structure snapshots the transport ops when the port is enabled and clears them when disabled. Signed-off-by:
-
Christoph Hellwig authored
The bfq schedule now uses css_next_descendant_pre directly after the stats functionality depending on it has been from the core blk-cgroup code to bfq. Export the symbol so that bfq can still be build modular. Fixes: d6258980 ("bfq-iosched: move bfq_stat_recursive_sum into the only caller") Signed-off-by:
-
https://github.com/liu-song-6/linuxJens Axboe authored
Pull MD changes from Song. * 'md-next' of https://github.com/liu-song-6/linux: md: add bitmap_abort label in md_run md-bitmap: create and destroy wb_info_pool with the change of bitmap md-bitmap: create and destroy wb_info_pool with the change of backlog md: introduce mddev_create/destroy_wb_pool for the change of member device md/raid1: fix potential data inconsistency issue with write behind device
-
- 20 Jun, 2019 5 commits
-
-
Guoqing Jiang authored
Now, there are two places need to consider about the failure of destroy bitmap, so move the common part between bitmap_abort and abort label. Reviewed-by:
NeilBrown <neilb@suse.com> Signed-off-by:
Guoqing Jiang <gqjiang@suse.com> Signed-off-by:
Song Liu <songliubraving@fb.com>
-
Guoqing Jiang authored
The write-behind attribute is part of bitmap, since bitmap can be added/removed dynamically with the following. 1. mdadm --grow /dev/md0 --bitmap=none 2. mdadm --grow /dev/md0 --bitmap=internal --write-behind So we need to destroy wb_info_pool in md_bitmap_destroy, and create the pool before load bitmap. Reviewed-by:
-
Guoqing Jiang authored
Since we can enable write-behind mode by write backlog node, so create wb_info_pool if the mode is just enabled, also call call md_bitmap_update_sb to make user aware the write-behind mode is enabled. Conversely, wb_info_pool should be destroyed when write-behind mode is disabled. Beside above, it is better to update bitmap sb if we change the number of max_write_behind. Reviewed-by:
-
Guoqing Jiang authored
Previously, we called rdev_init_wb to avoid potential data inconsistency when array is created. Now, we need to call the function and create mempool if a device is added or just be flaged as "writemostly". So mddev_create_wb_pool is introduced and called accordingly. And for safety reason, we mark implicit GFP_NOIO allocation scope for create mempool during mddev_suspend/mddev_resume. And mempool should be removed conversely after remove a member device or its's "writemostly" flag, which is done by call mddev_destroy_wb_pool. Reviewed-by:
-
Guoqing Jiang authored
For write-behind mode, we think write IO is complete once it has reached all the non-writemostly devices. It works fine for single queue devices. But for multiqueue device, if there are lots of IOs come from upper layer, then the write-behind device could issue those IOs to different queues, depends on the each queue's delay, so there is no guarantee that those IOs can arrive in order. To address the issue, we need to check the collision among write behind IOs, we can only continue without collision, otherwise wait for the completion of previous collisioned IO. And WBCollision is introduced for multiqueue device which is worked under write-behind mode. But this patch doesn't handle below cases which could have the data inconsistency issue as well, these cases will be handled in later patches. 1. modify max_write_behind by write backlog node. 2. add or remove array's bitmap dynamically. 3. the change of member disk. Reviewed-by:
-
