Pull s390 fixes from Heiko Carstens:

 - Disable address-of-packed-member warning in s390 specific boot code
   to get rid of a gcc9 warning which otherwise is already disabled for
   the whole kernel.

 - Fix yet another compiler error seen with CONFIG_OPTIMIZE_INLINING
   enabled.

 - Fix memory leak in vfio-ccw code on module exit.

* tag 's390-5.2-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  vfio-ccw: Destroy kmem cache region on module exit
  s390/ctl_reg: mark __ctl_set_bit and __ctl_clear_bit as __always_inline
  s390/boot: disable address-of-packed-member warning

Pull two misc vfs fixes from Jan Kara:
 "One small quota fix fixing spurious EDQUOT errors and one fanotify fix
  fixing a bug in the new fanotify FID reporting code"

* tag 'for_v5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  fanotify: update connector fsid cache on add mark
  quota: fix a problem about transfer quota

Pull MMC fixes from Ulf Hansson:
 "Here's quite a few MMC fixes intended for v5.2-rc6. This time it also
  contains fixes for a WiFi driver, which device is attached to the SDIO
  interface. Patches for the WiFi driver have been acked by the
  corresponding maintainers.

  Summary:

  MMC core:
   - Make switch to eMMC HS400 more robust for some controllers
   - Add two SDIO func API to manage re-tuning constraints
   - Prevent processing SDIO IRQs when the card is suspended

  MMC host:
   - sdhi: Disallow broken HS400 for M3-W ES1.2, RZ/G2M and V3H
   - mtk-sd: Fixup support for SDIO IRQs
   - sdhci-pci-o2micro: Fixup support for tuning

  Wireless BRCMFMAC (SDIO):
   - Deal with expected transmission errors related to the idle states
     (handled by the Always-On-Subsystem or AOS) on the SDIO-based WiFi
     on rk3288-veyron-minnie, rk3288-veyron-speedy and
     rk3288-veyron-mickey"

* tag 'mmc-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: core: Prevent processing SDIO IRQs when the card is suspended
  mmc: sdhci: sdhci-pci-o2micro: Correctly set bus width when tuning
  brcmfmac: sdio: Don't tune while the card is off
  mmc: core: Add sdio_retune_hold_now() and sdio_retune_release()
  brcmfmac: sdio: Disable auto-tuning around commands expected to fail
  mmc: core: API to temporarily disable retuning for SDIO CRC errors
  Revert "brcmfmac: disable command decode in sdio_aos"
  mmc: mediatek: fix SDIO IRQ detection issue
  mmc: mediatek: fix SDIO IRQ interrupt handle flow
  mmc: core: complete HS400 before checking status
  mmc: sdhi: disallow HS400 for M3-W ES1.2, RZ/G2M, and V3H

Pull block fixes from Jens Axboe:
 "Three fixes that should go into this series.

  One is a set of two patches from Christoph, fixing a page leak on same
  page merges. Boiled down version of a bigger fix, but this one is more
  appropriate for this late in the cycle (and easier to backport to
  stable).

  The last patch is for a divide error in MD, from Mariusz (via Song)"

* tag 'for-linus-20190620' of git://git.kernel.dk/linux-block:
  md: fix for divide error in status_resync
  block: fix page leak when merging to same page
  block: return from __bio_try_merge_page if merging occured in the same page

Jeff's picking up more responsibilities elsewhere, and Chuck's agreed to
take over.

For now, as before, nothing's changing day-to-day, but I want to have a
co-maintainer if only for bus factor.
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull power management fix from Rafael Wysocki:
 "Prevent PCI bridges in general (and PCIe ports in particular) from
  being put into low-power states during system-wide suspend transitions
  if there are any devices in D0 below them and refine the handling of
  PCI devices in D0 during suspend-to-idle cycles"

* tag 'pm-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PCI: PM: Skip devices in D0 for suspend-to-idle

Merge tag 'apparmor-pr-2019-06-18' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor

Pull apparmor bug fixes from John Johansen:

 - fix PROFILE_MEDIATES for untrusted input

 - enforce nullbyte at end of tag string

 - reset pos on failure to unpack for various functions

* tag 'apparmor-pr-2019-06-18' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor:
  apparmor: reset pos on failure to unpack for various functions
  apparmor: enforce nullbyte at end of tag string
  apparmor: fix PROFILE_MEDIATES for untrusted input

Pull input updates from Dmitry Torokhov:
 "Just a few small fixups and switching a couple of Thinkpads to SMBus
  for touchpads as PS/2 emulation is not working well"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: synaptics - enable SMBus on ThinkPad E480 and E580
  Input: imx_keypad - make sure keyboard can always wake up system
  Input: iqs5xx - get axis info before calling input_mt_init_slots()
  Input: uinput - add compat ioctl number translation for UI_*_FF_UPLOAD
  Input: silead - add MSSL0017 to acpi_device_id
  Input: elantech - enable middle button support on 2 ThinkPads
  Input: elan_i2c - increment wakeup count if wake source

When implementing connector fsid cache, we only initialized the cache
when the first mark added to object was added by FAN_REPORT_FID group.
We forgot to update conn->fsid when the second mark is added by
FAN_REPORT_FID group to an already attached connector without fsid
cache.

Reported-and-tested-by: syzbot+c277e8e2f46414645508@syzkaller.appspotmail.com
Fixes: 77115225 ("fanotify: cache fsid in fsnotify_mark_connector")
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>

Run below script as root, dquot_add_space will return -EDQUOT since
__dquot_transfer call dquot_add_space with flags=0, and dquot_add_space
think it's a preallocation. Fix it by set flags as DQUOT_SPACE_WARN.

mkfs.ext4 -O quota,project /dev/vdb
mount -o prjquota /dev/vdb /mnt
setquota -P 23 1 1 0 0 /dev/vdb
dd if=/dev/zero of=/mnt/test-file bs=4K count=1
chattr -p 23 test-file

Fixes: 7b9ca4c6 ("quota: Reduce contention on dq_data_lock")
Signed-off-by: yangerkun <yangerkun@huawei.com>
Signed-off-by: Jan Kara <jack@suse.cz>

Each function that manipulates the aa_ext struct should reset it's "pos"
member on failure. This ensures that, on failure, no changes are made to
the state of the aa_ext struct.

There are paths were elements are optional and the error path is
used to indicate the optional element is not present. This means
instead of just aborting on error the unpack stream can become
unsynchronized on optional elements, if using one of the affected
functions.

Cc: stable@vger.kernel.org
Fixes: 736ec752 ("AppArmor: policy routines for loading and unpacking policy")
Signed-off-by: Mike Salvatore <mike.salvatore@canonical.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>

A packed AppArmor policy contains null-terminated tag strings that are read
by unpack_nameX(). However, unpack_nameX() uses string functions on them
without ensuring that they are actually null-terminated, potentially
leading to out-of-bounds accesses.

Make sure that the tag string is null-terminated before passing it to
strcmp().

Cc: stable@vger.kernel.org
Fixes: 736ec752 ("AppArmor: policy routines for loading and unpacking policy")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>

While commit 11c236b8 ("apparmor: add a default null dfa") ensure
every profile has a policy.dfa it does not resize the policy.start[]
to have entries for every possible start value. Which means
PROFILE_MEDIATES is not safe to use on untrusted input. Unforunately
commit b9590ad4 ("apparmor: remove POLICY_MEDIATES_SAFE") did not
take into account the start value usage.

The input string in profile_query_cb() is user controlled and is not
properly checked to be within the limited start[] entries, even worse
it can't be as userspace policy is allowed to make us of entries types
the kernel does not know about. This mean usespace can currently cause
the kernel to access memory up to 240 entries beyond the start array
bounds.

Cc: stable@vger.kernel.org
Fixes: b9590ad4 ("apparmor: remove POLICY_MEDIATES_SAFE")
Signed-off-by: John Johansen <john.johansen@canonical.com>

Pull MD fix from Song.

* 'md-fixes' of https://github.com/liu-song-6/linux:
  md: fix for divide error in status_resync

Pull btrfs fixes from David Sterba:

 - regression where properties stored as xattrs are not properly
   persisted

 - a small readahead fix (the fstests testcase for that fix hangs on
   unpatched kernel, so we'd like get it merged to ease future testing)

 - fix a race during block group creation and deletion

* tag 'for-5.2-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  Btrfs: fix failure to persist compression property xattr deletion on fsync
  btrfs: start readahead also in seed devices
  Btrfs: fix race between block group removal and block group allocation

Pull ARM SoC fixes from Olof Johansson:
 "I've been bad at collecting fixes this release cycle, so this is a
  fairly large batch that's been trickling in for a while.

  It's the usual mix, more or less.

  Some of the bigger things fixed:

   - Voltage fix for MMC on TI DRA7 that sometimes would overvoltage
     cards

   - Regression fixes for D_CAN on am355x

   - i.MX6SX cpuidle fix to deal with wakeup latency (dropped uart
     chars)

   - DT fixes for some DRA7 variants that don't share the superset of
     blocks on the chip

  plus the usual mix of stuff: minor build/warning fixes, Kconfig
  dependencies, and some DT fixlets"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (28 commits)
  soc: ixp4xx: npe: Fix an IS_ERR() vs NULL check in probe
  ARM: ixp4xx: include irqs.h where needed
  ARM: ixp4xx: mark ixp4xx_irq_setup as __init
  ARM: ixp4xx: don't select SERIAL_OF_PLATFORM
  firmware: trusted_foundations: add ARMv7 dependency
  MAINTAINERS: Change QCOM repo location
  ARM: davinci: da8xx: specify dma_coherent_mask for lcdc
  ARM: davinci: da850-evm: call regulator_has_full_constraints()
  ARM: mvebu_v7_defconfig: fix Ethernet on Clearfog
  ARM: dts: am335x phytec boards: Fix cd-gpios active level
  ARM: dts: dra72x: Disable usb4_tm target module
  arm64: arch_k3: Fix kconfig dependency warning
  ARM: dts: Drop bogus CLKSEL for timer12 on dra7
  MAINTAINERS: Update Stefan Wahren email address
  ARM: dts: bcm: Add missing device_type = "memory" property
  soc: bcm: brcmstb: biuctrl: Register writes require a barrier
  soc: brcmstb: Fix error path for unsupported CPUs
  ARM: dts: dra71x: Disable usb4_tm target module
  ARM: dts: dra71x: Disable rtc target module
  ARM: dts: dra76x: Disable usb4_tm target module
  ...

Pull stack init fix from Kees Cook:
 "This is a small update to the stack auto-initialization self-test code
  to deal with the Clang initialization pattern.

  It's been in linux-next for a couple weeks; I had waited a bit
  wondering if anything more substantial was going to show up, but
  nothing has, so I'm sending this now before it gets too late"

* tag 'meminit-v5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  lib/test_stackinit: Handle Clang auto-initialization pattern

Stopping external metadata arrays during resync/recovery causes
retries, loop of interrupting and starting reconstruction, until it
hit at good moment to stop completely. While these retries
curr_mark_cnt can be small- especially on HDD drives, so subtraction
result can be smaller than 0. However it is casted to uint without
checking. As a result of it the status bar in /proc/mdstat while stopping
is strange (it jumps between 0% and 99%).

The real problem occurs here after commit 72deb455 ("block: remove
CONFIG_LBDAF"). Sector_div() macro has been changed, now the
divisor is casted to uint32. For db = -8 the divisior(db/32-1) becomes 0.

Check if db value can be really counted and replace these macro by
div64_u64() inline.
Signed-off-by: Mariusz Tkaczyk <mariusz.tkaczyk@intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>

The devm_ioremap_resource() function doesn't return NULL, it returns
error pointers.

Fixes: 0b458d7b ("soc: ixp4xx: npe: Pass addresses as resources")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Processing of SDIO IRQs must obviously be prevented while the card is
system suspended, otherwise we may end up trying to communicate with an
uninitialized SDIO card.

Reports throughout the years shows that this is not only a theoretical
problem, but a real issue. So, let's finally fix this problem, by keeping
track of the state for the card and bail out before processing the SDIO
IRQ, in case the card is suspended.

Cc: stable@vger.kernel.org
Reported-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The O2Micro controller only supports tuning at 4-bits. So the host driver
needs to change the bus width while tuning and then set it back when done.

There was a bug in the original implementation in that mmc->ios.bus_width
also wasn't updated. Thus setting the incorrect blocksize in
sdhci_send_tuning which results in a tuning failure.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Fixes: 0086fc21 ("mmc: sdhci: Add support for O2 hardware tuning")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

When Broadcom SDIO cards are idled they go to sleep and a whole
separate subsystem takes over their SDIO communication.  This is the
Always-On-Subsystem (AOS) and it can't handle tuning requests.

Specifically, as tested on rk3288-veyron-minnie (which reports having
BCM4354/1 in dmesg), if I force a retune in brcmf_sdio_kso_control()
when "on = 1" (aka we're transition from sleep to wake) by whacking:
  bus->sdiodev->func1->card->host->need_retune = 1
...then I can often see tuning fail.  In this case dw_mmc reports "All
phases bad!").  Note that I don't get 100% failure, presumably because
sometimes the card itself has already transitioned away from the AOS
itself by the time we try to wake it up.  If I force retuning when "on
= 0" (AKA force retuning right before sending the command to go to
sleep) then retuning is always OK.

NOTE: we need _both_ this patch and the patch to avoid triggering
tuning due to CRC errors in the sleep/wake transition, AKA ("brcmfmac:
sdio: Disable auto-tuning around commands expected to fail").  Though
both patches handle issues with Broadcom's AOS, the problems are
distinct:
1. We want to defer (but not ignore) asynchronous (like
   timer-requested) tuning requests till the card is awake.  However,
   we want to ignore CRC errors during the transition, we don't want
   to queue deferred tuning request.
2. You could imagine that the AOS could implement retuning but we
   could still get errors while transitioning in and out of the AOS.
   Similarly you could imagine a seamless transition into and out of
   the AOS (with no CRC errors) even if the AOS couldn't handle
   tuning.

ALSO NOTE: presumably there is never a desperate need to retune in
order to wake up the card, since doing so is impossible.  Luckily the
only way the card can get into sleep state is if we had a good enough
tuning to send it the command to put it into sleep, so presumably that
"good enough" tuning is enough to wake us up, at least with a few
retries.

Cc: stable@vger.kernel.org #v4.18+
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

We want SDIO drivers to be able to temporarily stop retuning when the
driver knows that the SDIO card is not in a state where retuning will
work (maybe because the card is asleep).  We'll move the relevant
functions to a place where drivers can call them.

Cc: stable@vger.kernel.org #v4.18+
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

There are certain cases, notably when transitioning between sleep and
active state, when Broadcom SDIO WiFi cards will produce errors on the
SDIO bus.  This is evident from the source code where you can see that
we try commands in a loop until we either get success or we've tried
too many times.  The comment in the code reinforces this by saying
"just one write attempt may fail"

Unfortunately these failures sometimes end up causing an "-EILSEQ"
back to the core which triggers a retuning of the SDIO card and that
blocks all traffic to the card until it's done.

Let's disable retuning around the commands we expect might fail.

Cc: stable@vger.kernel.org #v4.18+
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Normally when the MMC core sees an "-EILSEQ" error returned by a host
controller then it will trigger a retuning of the card.  This is
generally a good idea.

However, if a command is expected to sometimes cause transfer errors
then these transfer errors shouldn't cause a re-tuning.  This
re-tuning will be a needless waste of time.  One example case where a
transfer is expected to cause errors is when transitioning between
idle (sometimes referred to as "sleep" in Broadcom code) and active
state on certain Broadcom WiFi SDIO cards.  Specifically if the card
was already transitioning between states when the command was sent it
could cause an error on the SDIO bus.

Let's add an API that the SDIO function drivers can call that will
temporarily disable the auto-tuning functionality.  Then we can add a
call to this in the Broadcom WiFi driver and any other driver that
might have similar needs.

NOTE: this makes the assumption that the card is already tuned well
enough that it's OK to disable the auto-retuning during one of these
error-prone situations.  Presumably the driver code performing the
error-prone transfer knows how to recover / retry from errors.  ...and
after we can get back to a state where transfers are no longer
error-prone then we can enable the auto-retuning again.  If we truly
find ourselves in a case where the card needs to be retuned sometimes
to handle one of these error-prone transfers then we can always try a
few transfers first without auto-retuning and then re-try with
auto-retuning if the first few fail.

Without this change on rk3288-veyron-minnie I periodically see this in
the logs of a machine just sitting there idle:
  dwmmc_rockchip ff0d0000.dwmmc: Successfully tuned phase to XYZ

Cc: stable@vger.kernel.org #v4.18+
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This reverts commit 29f65891.

After that patch landed I find that my kernel log on
rk3288-veyron-minnie and rk3288-veyron-speedy is filled with:
brcmfmac: brcmf_sdio_bus_sleep: error while changing bus sleep state -110

This seems to happen every time the Broadcom WiFi transitions out of
sleep mode.  Reverting the commit fixes the problem for me, so that's
what this patch does.

Note that, in general, the justification in the original commit seemed
a little weak.  It looked like someone was testing on a SD card
controller that would sometimes die if there were CRC errors on the
bus.  This used to happen back in early days of dw_mmc (the controller
on my boards), but we fixed it.  Disabling a feature on all boards
just because one SD card controller is broken seems bad.

Fixes: 29f65891 ("brcmfmac: disable command decode in sdio_aos")
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Double Lo <double.lo@cypress.com>
Cc: Madhan Mohan R <madhanmohan.r@cypress.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: stable@vger.kernel.org
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Multiple ixp4xx specific files require macros from irqs.h that
were moved out from mach/irqs.h, e.g.:

arch/arm/mach-ixp4xx/vulcan-pci.c:41:19: error: this function declaration is not a prototype [-Werror,-Wstrict-prototypes]
arch/arm/mach-ixp4xx/vulcan-pci.c:49:10: error: implicit declaration of function 'IXP4XX_GPIO_IRQ' [-Werror,-Wimplicit-function-declaration]
                return IXP4XX_GPIO_IRQ(INTA);

Include this header in all files that failed to build because of
that.

Fixes: dc8ef8cd ("ARM: ixp4xx: Convert to SPARSE_IRQ")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>

Kbuild complains about ixp4xx_irq_setup not being __init
itself in some configurations:

WARNING: vmlinux.o(.text+0x85bae4): Section mismatch in reference from the function ixp4xx_irq_setup() to the function .init.text:set_handle_irq()
The function ixp4xx_irq_setup() references
the function __init set_handle_irq().
This is often because ixp4xx_irq_setup lacks a __init
annotation or the annotation of set_handle_irq is wrong.

I suspect it normally gets inlined, so we get no such warning,
but clang makes this obvious when the function is left out
of line.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>

Platforms should not normally select all the device drivers, leave that
up to the user and the defconfig file.

In this case, we get a warning for randconfig builds:

WARNING: unmet direct dependencies detected for SERIAL_OF_PLATFORM
  Depends on [n]: TTY [=y] && HAS_IOMEM [=y] && SERIAL_8250 [=n] && OF [=y]
  Selected by [y]:
  - MACH_IXP4XX_OF [=y] && ARCH_IXP4XX [=y]

Fixes: 9540724c ("ARM: ixp4xx: Add device tree boot support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>

The "+sec" extension is invalid for older ARM architectures, but
the code can now be built on any ARM configuration:

/tmp/trusted_foundations-2d0882.s: Assembler messages:
/tmp/trusted_foundations-2d0882.s:194: Error: architectural extension `sec' is not allowed for the current base architecture
/tmp/trusted_foundations-2d0882.s:201: Error: selected processor does not support `smc #0' in ARM mode
/tmp/trusted_foundations-2d0882.s:213: Error: architectural extension `sec' is not allowed for the current base architecture
/tmp/trusted_foundations-2d0882.s:220: Error: selected processor does not support `smc #0' in ARM mode

Add a dependency on ARMv7 for the build.

Fixes: 4cb5d9ec ("firmware: Move Trusted Foundations support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull vfs fixes from Al Viro:
 "MS_MOVE regression fix + breakage in fsmount(2) (also introduced in
  this cycle, along with fsmount(2) itself).

  I'm still digging through the piles of mail, so there might be more
  fixes to follow, but these two are obvious and self-contained, so
  there's no point delaying those..."

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs/namespace: fix unprivileged mount propagation
  vfs: fsmount: add missing mntget()

Pull networking fixes from David Miller:
 "Lots of bug fixes here:

   1) Out of bounds access in __bpf_skc_lookup, from Lorenz Bauer.

   2) Fix rate reporting in cfg80211_calculate_bitrate_he(), from John
      Crispin.

   3) Use after free in psock backlog workqueue, from John Fastabend.

   4) Fix source port matching in fdb peer flow rule of mlx5, from Raed
      Salem.

   5) Use atomic_inc_not_zero() in fl6_sock_lookup(), from Eric Dumazet.

   6) Network header needs to be set for packet redirect in nfp, from
      John Hurley.

   7) Fix udp zerocopy refcnt, from Willem de Bruijn.

   8) Don't assume linear buffers in vxlan and geneve error handlers,
      from Stefano Brivio.

   9) Fix TOS matching in mlxsw, from Jiri Pirko.

  10) More SCTP cookie memory leak fixes, from Neil Horman.

  11) Fix VLAN filtering in rtl8366, from Linus Walluij.

  12) Various TCP SACK payload size and fragmentation memory limit fixes
      from Eric Dumazet.

  13) Use after free in pneigh_get_next(), also from Eric Dumazet.

  14) LAPB control block leak fix from Jeremy Sowden"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (145 commits)
  lapb: fixed leak of control-blocks.
  tipc: purge deferredq list for each grp member in tipc_group_delete
  ax25: fix inconsistent lock state in ax25_destroy_timer
  neigh: fix use-after-free read in pneigh_get_next
  tcp: fix compile error if !CONFIG_SYSCTL
  hv_sock: Suppress bogus "may be used uninitialized" warnings
  be2net: Fix number of Rx queues used for flow hashing
  net: handle 802.1P vlan 0 packets properly
  tcp: enforce tcp_min_snd_mss in tcp_mtu_probing()
  tcp: add tcp_min_snd_mss sysctl
  tcp: tcp_fragment() should apply sane memory limits
  tcp: limit payload size of sacked skbs
  Revert "net: phylink: set the autoneg state in phylink_phy_change"
  bpf: fix nested bpf tracepoints with per-cpu data
  bpf: Fix out of bounds memory access in bpf_sk_storage
  vsock/virtio: set SOCK_DONE on peer shutdown
  net: dsa: rtl8366: Fix up VLAN filtering
  net: phylink: set the autoneg state in phylink_phy_change
  net: add high_order_alloc_disable sysctl/static key
  tcp: add tcp_tx_skb_cache sysctl
  ...

When propagating mounts across mount namespaces owned by different user
namespaces it is not possible anymore to move or umount the mount in the
less privileged mount namespace.

Here is a reproducer:

  sudo mount -t tmpfs tmpfs /mnt
  sudo --make-rshared /mnt

  # create unprivileged user + mount namespace and preserve propagation
  unshare -U -m --map-root --propagation=unchanged

  # now change back to the original mount namespace in another terminal:
  sudo mkdir /mnt/aaa
  sudo mount -t tmpfs tmpfs /mnt/aaa

  # now in the unprivileged user + mount namespace
  mount --move /mnt/aaa /opt

Unfortunately, this is a pretty big deal for userspace since this is
e.g. used to inject mounts into running unprivileged containers.
So this regression really needs to go away rather quickly.

The problem is that a recent change falsely locked the root of the newly
added mounts by setting MNT_LOCKED. Fix this by only locking the mounts
on copy_mnt_ns() and not when adding a new mount.

Fixes: 3bd045cc ("separate copying and locking mount tree on cross-userns copies")
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Tested-by: Christian Brauner <christian@brauner.io>
Acked-by: Christian Brauner <christian@brauner.io>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Christian Brauner <christian@brauner.io>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

sys_fsmount() needs to take a reference to the new mount when adding it
to the anonymous mount namespace.  Otherwise the filesystem can be
unmounted while it's still in use, as found by syzkaller.
Reported-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: syzbot+99de05d099a170867f22@syzkaller.appspotmail.com
Reported-by: syzbot+7008b8b8ba7df475fdc8@syzkaller.appspotmail.com
Fixes: 93766fbd ("vfs: syscall: Add fsmount() to create a mount for a superblock")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Eric Dumazet says:

====================
tcp: make sack processing more robust

Jonathan Looney brought to our attention multiple problems
in TCP stack at the sender side.

SACK processing can be abused by malicious peers to either
cause overflows, or increase of memory usage.

First two patches fix the immediate problems.

Since the malicious peers abuse senders by advertizing a very
small MSS in their SYN or SYNACK packet, the last two
patches add a new sysctl so that admins can chose a higher
limit for MSS clamping.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull RISC-V fixes from Paul Walmsley:
 "This contains fixes, defconfig, and DT data changes for the v5.2-rc
  series.

  The fixes are relatively straightforward:

   - Addition of a TLB fence in the vmalloc_fault path, so the CPU
     doesn't enter an infinite page fault loop

   - Readdition of the pm_power_off export, so device drivers that
     reassign it can now be built as modules

   - A udelay() fix for RV32, fixing a miscomputation of the delay time

   - Removal of deprecated smp_mb__*() barriers

  This also adds initial DT data infrastructure for arch/riscv, along
  with initial data for the SiFive FU540-C000 SoC and the corresponding
  HiFive Unleashed board.

  We also update the RV64 defconfig to include some core drivers for the
  FU540 in the build"

* tag 'riscv-for-v5.2/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: remove unused barrier defines
  riscv: mm: synchronize MMU after pte change
  riscv: dts: add initial board data for the SiFive HiFive Unleashed
  riscv: dts: add initial support for the SiFive FU540-C000 SoC
  dt-bindings: riscv: convert cpu binding to json-schema
  dt-bindings: riscv: sifive: add YAML documentation for the SiFive FU540
  arch: riscv: add support for building DTB files from DT source data
  riscv: Fix udelay in RV32.
  riscv: export pm_power_off again
  RISC-V: defconfig: enable clocks, serial console

When multiple iovecs reference the same page, each get_user_page call
will add a reference to the page.  But once we've created the bio that
information gets lost and only a single reference will be dropped after
I/O completion.  Use the same_page information returned from
__bio_try_merge_page to drop additional references to pages that were
already present in the bio.

Based on a patch from Ming Lei.

Link: https://lkml.org/lkml/2019/4/23/64
Fixes: 576ed913 ("block: use bio_add_page in bio_iov_iter_get_pages")
Reported-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

We currently have an input same_page parameter to __bio_try_merge_page
to prohibit merging in the same page.  The rationale for that is that
some callers need to account for every page added to a bio.  Instead of
letting these callers call twice into the merge code to account for the
new vs existing page cases, just turn the paramter into an output one that
returns if a merge in the same page occured and let them act accordingly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

After the recent series of cleanups in the properties and xattrs modules
that landed in the 5.2 merge window, we ended up with a regression where
after deleting the compression xattr property through the setflags ioctl,
we don't set the BTRFS_INODE_COPY_EVERYTHING flag in the inode anymore.
As a consequence, if the inode was fsync'ed when it had the compression
property set, after deleting the compression property through the setflags
ioctl and fsync'ing again the inode, the log will still contain the
compression xattr, because the inode did not had that bit set, which
made the fsync not delete all xattrs from the log and copy all xattrs
from the subvolume tree to the log tree.

This regression happens due to the fact that that series of cleanups
made btrfs_set_prop() call the old function do_setxattr() (which is now
named btrfs_setxattr()), and not the old version of btrfs_setxattr(),
which is now called btrfs_setxattr_trans().

Fix this by setting the BTRFS_INODE_COPY_EVERYTHING bit in the current
btrfs_setxattr() function and remove it from everywhere else, including
its setup at btrfs_ioctl_setflags(). This is cleaner, avoids similar
regressions in the future, and centralizes the setup of the bit. After
all, the need to setup this bit should only be in the xattrs module,
since it is an implementation of xattrs.

Fixes: 04e6863b ("btrfs: split btrfs_setxattr calls regarding transaction")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>

They were introduced in commit fab957c1 ("RISC-V: Atomic and
Locking Code") long after commit 2e39465a ("locking: Remove
deprecated smp_mb__() barriers") removed the remnants of all previous
instances from the tree.
Signed-off-by: Rolf Eike Beer <eb@emlix.com>
[paul.walmsley@sifive.com: stripped spurious mbox header from patch
 description; fixed commit references in patch header]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>