ethtool ena_get_channels() expose the max number of queues as the max
number of queues ENA supports (128 queues) and not the actual number
of created queues.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This failure is rare and only found on testing where deliberately fail
devm_ioremap()

[  451.170464] ena 0000:04:00.0: failed to remap regs bar
451.170549] Workqueue: pciehp-1 pciehp_power_thread
[  451.170551] task: ffff88085a5f2d00 task.stack: ffffc9000756c000
[  451.170552] RIP: 0010:devm_iounmap+0x2d/0x40
[  451.170553] RSP: 0018:ffffc9000756fac0 EFLAGS: 00010282
[  451.170554] RAX: 00000000fffffffe RBX: 0000000000000000 RCX:
0000000000000000
[  451.170555] RDX: ffffffff813a7e00 RSI: 0000000000000282 RDI:
0000000000000282
[  451.170556] RBP: ffffc9000756fac8 R08: 00000000fffffffe R09:
00000000000009b7
[  451.170557] R10: 0000000000000005 R11: 00000000000009b6 R12:
ffff880856c9d0a0
[  451.170558] R13: ffffc9000f5c90c0 R14: ffff880856c9d0a0 R15:
0000000000000028
[  451.170559] FS:  0000000000000000(0000) GS:ffff88085f400000(0000)
knlGS:0000000000000000
[  451.170560] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  451.170561] CR2: 00007f169038b000 CR3: 0000000001c09000 CR4:
00000000003406f0
[  451.170562] DR0: 0000000000000000 DR1: 0000000000000000 DR2:
0000000000000000
[  451.170562] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7:
0000000000000400
[  451.170563] Call Trace:
[  451.170572]  ena_release_bars.isra.48+0x34/0x60 [ena]
[  451.170574]  ena_probe+0x144/0xd90 [ena]
[  451.170579]  ? ida_simple_get+0x98/0x100
[  451.170585]  ? kernfs_next_descendant_post+0x40/0x50
[  451.170591]  local_pci_probe+0x45/0xa0
[  451.170592]  pci_device_probe+0x157/0x180
[  451.170599]  driver_probe_device+0x2a8/0x460
[  451.170600]  __device_attach_driver+0x7e/0xe0
[  451.170602]  ? driver_allows_async_probing+0x30/0x30
[  451.170603]  bus_for_each_drv+0x68/0xb0
[  451.170605]  __device_attach+0xdd/0x160
[  451.170607]  device_attach+0x10/0x20
[  451.170610]  pci_bus_add_device+0x4f/0xa0
[  451.170611]  pci_bus_add_devices+0x39/0x70
[  451.170613]  pciehp_configure_device+0x96/0x120
[  451.170614]  pciehp_enable_slot+0x1b3/0x290
[  451.170616]  pciehp_power_thread+0x3b/0xb0
[  451.170622]  process_one_work+0x149/0x360
[  451.170623]  worker_thread+0x4d/0x3c0
[  451.170626]  kthread+0x109/0x140
[  451.170627]  ? rescuer_thread+0x380/0x380
[  451.170628]  ? kthread_park+0x60/0x60
[  451.170632]  ret_from_fork+0x25/0x30
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Decrease log level of checksum errors as these messages can be
triggered remotely by bad packets.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit f1174f77 ("bpf/verifier: rework value tracking")
removed the crafty selection of which pointer types are
allowed to be modified.  This is OK for most pointer types
since adjust_ptr_min_max_vals() will catch operations on
immutable pointers.  One exception is PTR_TO_CTX which is
now allowed to be offseted freely.

The intent of aforementioned commit was to allow context
access via modified registers.  The offset passed to
->is_valid_access() verifier callback has been adjusted
by the value of the variable offset.

What is missing, however, is taking the variable offset
into account when the context register is used.  Or in terms
of the code adding the offset to the value passed to the
->convert_ctx_access() callback.  This leads to the following
eBPF user code:

     r1 += 68
     r0 = *(u32 *)(r1 + 8)
     exit

being translated to this in kernel space:

   0: (07) r1 += 68
   1: (61) r0 = *(u32 *)(r1 +180)
   2: (95) exit

Offset 8 is corresponding to 180 in the kernel, but offset
76 is valid too.  Verifier will "accept" access to offset
68+8=76 but then "convert" access to offset 8 as 180.
Effective access to offset 248 is beyond the kernel context.
(This is a __sk_buff example on a debug-heavy kernel -
packet mark is 8 -> 180, 76 would be data.)

Dereferencing the modified context pointer is not as easy
as dereferencing other types, because we have to translate
the access to reading a field in kernel structures which is
usually at a different offset and often of a different size.
To allow modifying the pointer we would have to make sure
that given eBPF instruction will always access the same
field or the fields accessed are "compatible" in terms of
offset and size...

Disallow dereferencing modified context pointers and add
to selftests the test case described here.

Fixes: f1174f77 ("bpf/verifier: rework value tracking")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It seems that it's possible to toggle NETLINK_F_EXT_ACK
through setsockopt() while another thread/CPU is building
a message inside netlink_ack(), which could then trigger
the WARN_ON()s I added since if it goes from being turned
off to being turned on between allocating and filling the
message, the skb could end up being too small.

Avoid this whole situation by storing the value of this
flag in a separate variable and using that throughout the
function instead.

Fixes: 2d4bc933 ("netlink: extended ACK reporting")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch correctly sets the number of additional header descriptors
that will be sent in an indirect SCRQ entry.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When an EMAD is transmitted, a timeout work item is scheduled with a
delay of 200ms, so that another EMAD will be retried until a maximum of
five retries.

In certain situations, it's possible for the function waiting on the
EMAD to be associated with a work item that is queued on the same
workqueue (`mlxsw_core`) as the timeout work item. This results in
flushing a work item on the same workqueue.

According to commit e159489b ("workqueue: relax lockdep annotation
on flush_work()") the above may lead to a deadlock in case the workqueue
has only one worker active or if the system in under memory pressure and
the rescue worker is in use. The latter explains the very rare and
random nature of the lockdep splats we have been seeing:

[   52.730240] ============================================
[   52.736179] WARNING: possible recursive locking detected
[   52.742119] 4.14.0-rc3jiri+ #4 Not tainted
[   52.746697] --------------------------------------------
[   52.752635] kworker/1:3/599 is trying to acquire lock:
[   52.758378]  (mlxsw_core_driver_name){+.+.}, at: [<ffffffff811c4fa4>] flush_work+0x3a4/0x5e0
[   52.767837]
               but task is already holding lock:
[   52.774360]  (mlxsw_core_driver_name){+.+.}, at: [<ffffffff811c65c4>] process_one_work+0x7d4/0x12f0
[   52.784495]
               other info that might help us debug this:
[   52.791794]  Possible unsafe locking scenario:
[   52.798413]        CPU0
[   52.801144]        ----
[   52.803875]   lock(mlxsw_core_driver_name);
[   52.808556]   lock(mlxsw_core_driver_name);
[   52.813236]
                *** DEADLOCK ***
[   52.819857]  May be due to missing lock nesting notation
[   52.827450] 3 locks held by kworker/1:3/599:
[   52.832221]  #0:  (mlxsw_core_driver_name){+.+.}, at: [<ffffffff811c65c4>] process_one_work+0x7d4/0x12f0
[   52.842846]  #1:  ((&(&bridge->fdb_notify.dw)->work)){+.+.}, at: [<ffffffff811c65c4>] process_one_work+0x7d4/0x12f0
[   52.854537]  #2:  (rtnl_mutex){+.+.}, at: [<ffffffff822ad8e7>] rtnl_lock+0x17/0x20
[   52.863021]
               stack backtrace:
[   52.867890] CPU: 1 PID: 599 Comm: kworker/1:3 Not tainted 4.14.0-rc3jiri+ #4
[   52.875773] Hardware name: Mellanox Technologies Ltd. "MSN2100-CB2F"/"SA001017", BIOS 5.6.5 06/07/2016
[   52.886267] Workqueue: mlxsw_core mlxsw_sp_fdb_notify_work [mlxsw_spectrum]
[   52.894060] Call Trace:
[   52.909122]  __lock_acquire+0xf6f/0x2a10
[   53.025412]  lock_acquire+0x158/0x440
[   53.047557]  flush_work+0x3c4/0x5e0
[   53.087571]  __cancel_work_timer+0x3ca/0x5e0
[   53.177051]  cancel_delayed_work_sync+0x13/0x20
[   53.182142]  mlxsw_reg_trans_bulk_wait+0x12d/0x7a0 [mlxsw_core]
[   53.194571]  mlxsw_core_reg_access+0x586/0x990 [mlxsw_core]
[   53.225365]  mlxsw_reg_query+0x10/0x20 [mlxsw_core]
[   53.230882]  mlxsw_sp_fdb_notify_work+0x2a3/0x9d0 [mlxsw_spectrum]
[   53.237801]  process_one_work+0x8f1/0x12f0
[   53.321804]  worker_thread+0x1fd/0x10c0
[   53.435158]  kthread+0x28e/0x370
[   53.448703]  ret_from_fork+0x2a/0x40
[   53.453017] mlxsw_spectrum 0000:01:00.0: EMAD retries (2/5) (tid=bf4549b100000774)
[   53.453119] mlxsw_spectrum 0000:01:00.0: EMAD retries (5/5) (tid=bf4549b100000770)
[   53.453132] mlxsw_spectrum 0000:01:00.0: EMAD reg access failed (tid=bf4549b100000770,reg_id=200b(sfn),type=query,status=0(operation performed))
[   53.453143] mlxsw_spectrum 0000:01:00.0: Failed to get FDB notifications

Fix this by creating another workqueue for EMAD timeouts, thereby
preventing the situation of a work item trying to flush a work item
queued on the same workqueue.

Fixes: caf7297e ("mlxsw: core: Introduce support for asynchronous EMAD register access")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2017-10-16' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Just a single fix, for a WoWLAN-related part of CVE-2017-13080.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When changing dev tx_queue_len via netlink or net-sysfs,
a NETDEV_CHANGE_TX_QUEUE_LEN event notification will be
called.

But dev_ioctl missed this event notification, which could
cause no userspace notification would be sent.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 7091d8c7 '(net/sched: cls_flower: Add offload support using egress
Hardware device') made sure (when fl_hw_replace_filter is called) to put
the egress_dev mark on persisent structure instance. Hence, following calls
into the HW driver for stats and deletion will note it and act accordingly.

With commit de4784ca this property is lost and hence when called,
the HW driver failes to operate (stats, delete) on the offloaded flow.

Fix it by setting the egress_dev flag whenever the ingress device is
different from the hw device since this is exactly the condition under
which we're calling into the HW driver through the egress port net-device.

Fixes: de4784ca ('net: sched: get rid of struct tc_to_netdev')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roi Dayan <roid@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

register_netdevice() could fail early when we have an invalid
dev name, in which case ->ndo_uninit() is not called. For tun
device, this is a problem because a timer etc. are already
initialized and it expects ->ndo_uninit() to clean them up.

We could move these initializations into a ->ndo_init() so
that register_netdevice() knows better, however this is still
complicated due to the logic in tun_detach().

Therefore, I choose to just call dev_get_valid_name() before
register_netdevice(), which is quicker and much easier to audit.
And for this specific case, it is already enough.

Fixes: 96442e42 ("tuntap: choose the txq based on rxq")
Reported-by: Dmitry Alexeev <avekceeb@gmail.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IFLA_IFALIAS is defined as NLA_STRING. It means that the minimal length of
the attribute is 1 ("\0"). However, to remove an alias, the attribute
length must be 0 (see dev_set_alias()).

Let's define the type to NLA_BINARY to allow 0-length string, so that the
alias can be removed.

Example:
$ ip l s dummy0 alias foo
$ ip l l dev dummy0
5: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
    link/ether ae:20:30:4f:a7:f3 brd ff:ff:ff:ff:ff:ff
    alias foo

Before the patch:
$ ip l s dummy0 alias ""
RTNETLINK answers: Numerical result out of range

After the patch:
$ ip l s dummy0 alias ""
$ ip l l dev dummy0
5: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
    link/ether ae:20:30:4f:a7:f3 brd ff:ff:ff:ff:ff:ff

CC: Oliver Hartkopp <oliver@hartkopp.net>
CC: Stephen Hemminger <stephen@networkplumber.org>
Fixes: 96ca4a2c ("net: remove ifalias on empty given alias")
Reported-by: Julien FLoret <julien.floret@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Xin Long says:

====================
rtnetlink: a bunch of fixes for userspace notifications in changing dev properties

Whenever any property of a link, address, route, etc. changes by whatever way,
kernel should notify the programs that listen for such events in userspace.

The patchet "rtnetlink: Cleanup user notifications for netdev events" tried to
fix a redundant notifications issue, but it also introduced a side effect.

After that, user notifications could only be sent when changing dev properties
via netlink api. As it removed some events process in rtnetlink_event where
the notifications was sent to users.

It resulted in no notification generated when dev properties are changed via
other ways, like ioctl, sysfs, etc. It may cause some user programs doesn't
work as expected because of the missing notifications.

This patchset will fix it by bringing some of these netdev events back and
also fix the old redundant notifications issue with a proper way.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

NETDEV_CHANGE_TX_QUEUE_LEN event process in rtnetlink_event would
send a notification for userspace and tx_queue_len's setting in
do_setlink would trigger NETDEV_CHANGE_TX_QUEUE_LEN.

So it shouldn't set DO_SETLINK_NOTIFY status for this change to
send a notification any more.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The check 'status & DO_SETLINK_NOTIFY' in do_setlink doesn't really
work after status & DO_SETLINK_MODIFIED, as:

  DO_SETLINK_MODIFIED 0x1
  DO_SETLINK_NOTIFY 0x3

Considering that notifications are suppposed to be sent only when
status have the flag DO_SETLINK_NOTIFY, the right check would be:

  (status & DO_SETLINK_NOTIFY) == DO_SETLINK_NOTIFY

This would avoid lots of duplicated notifications when setting some
properties of a link.

Fixes: ba998906 ("rtnl/do_setlink(): notify when a netdev is modified")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

libteam needs this event notification in userspace when dev's master
dev has been changed. After this, the redundant notifications issue
would be fixed in the later patch 'rtnetlink: check DO_SETLINK_NOTIFY
correctly in do_setlink'.

Fixes: b6b36eb2 ("rtnetlink: Do not generate notifications for NETDEV_CHANGEUPPER event")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As I said in patch 'rtnetlink: bring NETDEV_CHANGEMTU event process back
in rtnetlink_event', removing NETDEV_POST_TYPE_CHANGE event was not the
right fix for the redundant notifications issue.

So bring this event process back to rtnetlink_event and the old redundant
notifications issue would be fixed in the later patch 'rtnetlink: check
DO_SETLINK_NOTIFY correctly in do_setlink'.

Fixes: aef091ae ("rtnetlink: Do not generate notifications for POST_TYPE_CHANGE event")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The same fix for changing mtu in the patch 'rtnetlink: bring
NETDEV_CHANGEMTU event process back in rtnetlink_event' is
needed for changing tx_queue_len.

Note that the redundant notifications issue for tx_queue_len
will be fixed in the later patch 'rtnetlink: do not send
notification for tx_queue_len in do_setlink'.

Fixes: 27b3b551 ("rtnetlink: Do not generate notifications for NETDEV_CHANGE_TX_QUEUE_LEN event")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 085e1a65 ("rtnetlink: Do not generate notifications for MTU
events") tried to fix the redundant notifications issue when ip link
set mtu by removing NETDEV_CHANGEMTU event process in rtnetlink_event.

But it also resulted in no notification generated when dev's mtu is
changed via other methods, like:
  'ifconfig eth1 mtu 1400' or 'echo 1400 > /sys/class/net/eth1/mtu'
It would cause users not to be notified by this change.

This patch is to fix it by bringing NETDEV_CHANGEMTU event back into
rtnetlink_event, and the redundant notifications issue will be fixed
in the later patch 'rtnetlink: check DO_SETLINK_NOTIFY correctly in
do_setlink'.

Fixes: 085e1a65 ("rtnetlink: Do not generate notifications for MTU events")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a key is reinstalled we can reset the replay counters
etc. which can lead to nonce reuse and/or replay detection
being impossible, breaking security properties, as described
in the "KRACK attacks".

In particular, CVE-2017-13080 applies to GTK rekeying that
happened in firmware while the host is in D3, with the second
part of the attack being done after the host wakes up. In
this case, the wpa_supplicant mitigation isn't sufficient
since wpa_supplicant doesn't know the GTK material.

In case this happens, simply silently accept the new key
coming from userspace but don't take any action on it since
it's the same key; this keeps the PN replay counters intact.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Michael Chan says:

====================
bnxt_en: bug fixes.

Various bug fixes for the VF/PF link change logic, VF resource checking,
potential firmware response corruption on NVRAM and DCB parameters,
and reading the wrong register for PCIe link speed on the VF.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

hwrm_send_message() is replaced with _hwrm_send_message(), and
hwrm_cmd_lock mutex lock is grabbed for the whole period of
firmware call until the firmware DCB parameters have been copied.
This will prevent possible corruption of the firmware data.

Fixes: 7df4ae9f ("bnxt_en: Implement DCBNL to support host-based DCBX.")
Signed-off-by: Sankar Patchineelam <sankar.patchineelam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In bnxt_find_nvram_item(), it is copying firmware response data after
releasing the mutex.  This can cause the firmware response data
to be corrupted if the next firmware response overwrites the response
buffer.  The rare problem shows up when running ethtool -i repeatedly.

Fix it by calling the new variant _hwrm_send_message_silent() that requires
the caller to take the mutex and to release it after the response data has
been copied.

Fixes: 3ebf6f0a ("bnxt_en: Add installed-package version reporting via Ethtool GDRVINFO")
Reported-by: Sarveswara Rao Mygapula <sarveswararao.mygapula@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In bnxt_sriov_enable(), we calculate to see if we have enough hardware
resources to enable the requested number of VFs.  The logic to check
for minimum completion rings and statistics contexts is missing.  Add
the required checks so that VF configuration won't fail.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PCIE PCIE_EP_REG_LINK_STATUS_CONTROL register is only defined in PF
config space, so we must read it from the PF.

Fixes: 90c4f788 ("bnxt_en: Report PCIe link speed and width during driver load")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As a further improvement to the PF/VF link change logic, use a private
mutex instead of the rtnl lock to protect link change logic.  With the
new mutex, we don't have to take the rtnl lock in the workqueue when
we have to handle link related functions.  If the VF and PF drivers
are running on the same host and both take the rtnl lock and one is
waiting for the other, it will cause timeout.  This patch fixes these
timeouts.

Fixes: 90c694bb ("bnxt_en: Fix RTNL lock usage on bnxt_update_link().")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Link status query firmware messages originating from the VFs are forwarded
to the PF.  The driver handles these interactions in a workqueue for the
VF and PF.  The VF driver waits for the response from the PF in the
workqueue.  If the PF and VF driver are running on the same host and the
work for both PF and VF are queued on the same workqueue, the VF driver
may not get the response if the PF work item is queued behind it on the
same workqueue.  This will lead to the VF link query message timing out.

To prevent this, we create a private workqueue for PFs instead of using
the common workqueue.  The VF query and PF response will never be on
the same workqueue.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 88E6060 Ethernet switch always transmits the multicast bit of the
switch MAC address as a zero. It re-uses the corresponding bit 8 of the
register "Switch MAC Address Register Bytes 0 & 1" for "DiffAddr".

If the "DiffAddr" bit is 0, then all ports transmit the same source
address. If it is set to 1, then bit 2:0 are used for the port number.

The mv88e6060 driver is currently wrongly shifting the MAC address byte
0 by 9. To fix this, shift it by 8 as usual and clear its bit 0.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When pppol2tp_session_ioctl() is called by pppol2tp_tunnel_ioctl(),
the session may be unconnected. That is, it was created by
pppol2tp_session_create() and hasn't been connected with
pppol2tp_connect(). In this case, ps->sock is NULL, so we need to check
for this case in order to avoid dereferencing a NULL pointer.

Fixes: 309795f4 ("l2tp: Add netlink control API for L2TP")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

The DMA reset timeout, used in read_poll_timeout, is
ten times shorter than the sleep time.
This patch fixes these values interchanging them, as it was
before the read_poll_timeout introduction.

Fixes: 8a70aeca ("net: stmmac: Use readl_poll_timeout")
Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While experimenting with changes to the timekeeping code, I
ran into a build error in the liquidio driver:

drivers/net/ethernet/cavium/liquidio/lio_main.c: In function 'liquidio_ptp_settime':
drivers/net/ethernet/cavium/liquidio/lio_main.c:1850:22: error: passing argument 1 of 'timespec_to_ns' from incompatible pointer type [-Werror=incompatible-pointer-types]

The driver had a type mismatch since it was first merged, but
this never caused problems because it is only built on 64-bit
architectures that define timespec and timespec64 to the same
type.

If we ever want to compile-test the driver on 32-bit or change
the way that 64-bit timespec64 is defined, we need to fix it,
so let's just do it now.

Fixes: f21fb3ed ("Add support of Cavium Liquidio ethernet adapters")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2017-10-13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.14

Nothing really special standing out, all of these are important fixes
which should go to 4.14.

iwlwifi

* fix support for 3168 device series

* fix a potential crash when using FW debugging recording;

* improve channel flags parsing to avoid warnings on too long traces

* return -ENODATA when the temperature is not available, since the
 -EIO we were returning was causing fatal errors in userspace

* avoid printing too many messages in dmesg when using monitor mode,
  since this can become very noisy and completely flood the logs

brcmsmac

* reduce stack usage to avoid frame size warnings with KASAN

brcmfmac

* add a check to avoid copying uninitialised memory

rtlwifi:

* fix a regression with rtl8821ae starting from v4.11 where
  connections was frequently lost
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The kernel config help for policy routing was still pointing at
an ancient document from 2000 that refers to Linux 2.1. Update it
to point to something that is at least occasionally updated.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently we drop any new VLAN ids if there are more than the current
(or last used) channel can support. Most importantly this is a problem
if no channel has been selected yet, resulting in a segfault.

Secondly this does not necessarily reflect the capabilities of any other
channels. Instead only drop a new VLAN id if we are already tracking the
maximum allowed by the NCSI specification. Per-channel limits are
already handled by ncsi_add_filter(), but add a message to set_one_vid()
to make it obvious that the channel can not support any more VLAN ids.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtl_init_one() currently enables PCI wakeups if the ethernet device
is found to be WOL-capable. There is no need to do this when
rtl8169_set_wol() will correctly enable or disable the same wakeup flag
when WOL is activated/deactivated.

This works around an ACPI DSDT bug which prevents the Acer laptop models
Aspire ES1-533, Aspire ES1-732, PackardBell ENTE69AP and Gateway NE533
from entering S3 suspend - even when no ethernet cable is connected.

On these platforms, the DSDT says that GPE08 is a wakeup source for
ethernet, but this GPE fires as soon as the system goes into suspend,
waking the system up immediately. Having the wakeup normally disabled
avoids this issue in the default case.

With this change, WOL will continue to be unusable on these platforms
(it will instantly wake up if WOL is later enabled by the user) but we
do not expect this to be a commonly used feature on these consumer
laptops. We have separately determined that WOL works fine without any
ACPI GPEs enabled during sleep, so a DSDT fix or override would be
possible to make WOL work.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes: cda7ea69 ("macsec: check return value of skb_to_sgvec always")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

If for some reason, the newly allocated child need to be freed,
we will call cgroup_put() (via sk_free_unlock_clone()) while the
corresponding cgroup_get() was not yet done, and we will free memory
too soon.

Fixes: d979a39d ("cgroup: duplicate cgroup reference when cloning sockets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit fbb1fb4a.

This was not the proper fix, lets cleanly revert it, so that
following patch can be carried to stable versions.

sock_cgroup_ptr() callers do not expect a NULL return value.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
nfp: fix ethtool stats and page allocation

Two fixes for net.  First one makes sure we handle gather of stats on
32bit machines correctly (ouch).  The second fix solves a potential
NULL-deref if we fail to allocate a page with XDP running.

I used Fixes: tags pointing to where the bug was introduced, but for
patch 1 it has been in the driver "for ever" and fix won't backport
cleanly beyond commit 325945ed ("nfp: split software and hardware
vNIC statistics") which is in net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>