- 15 Mar, 2016 40 commits
-
-
Tariq Toukan authored
commit 59a7c2fd upstream. With the MLX5E_CQ_HAS_CQES optimization flag, the following buggy flow might occur: - Suppose RX is always busy, TX has a single packet every second. - We poll a single TX cqe and clear its flag. - We never arm it again as RX is always busy. - TX CQ flag is never changed, and new TX cqes are not polled. We revert this optimization. Fixes: e586b3b0 ('net/mlx5: Ethernet Datapath files') Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net> [ kamal: backport to 4.2-stable: context around mlx5e_poll_rx_cq return ] Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Florian Westphal authored
commit 5d150a98 upstream. When ipv6_find_hdr is used to find a fragment header (caller specifies target NEXTHDR_FRAGMENT) we erronously return -ENOENT for all fragments with nonzero offset. Before commit 9195bb8e, when target was specified, we did not enter the exthdr walk loop as nexthdr == target so this used to work. Now we do (so we can skip empty route headers). When we then stumble upon a frag with nonzero frag_off we must return -ENOENT ("header not found") only if the caller did not specifically request NEXTHDR_FRAGMENT. This allows nfables exthdr expression to match ipv6 fragments, e.g. via nft add rule ip6 filter input frag frag-off gt 0 Fixes: 9195bb8e ("ipv6: improve ipv6_find_hdr() to skip empty routing headers") Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
-
Jack Morgenstein authored
commit 6e522422 upstream. The VF administrative mac addresses (stored in the PF driver) are initialized to zero when the PF driver starts up. These addresses may be modified in the PF driver through ndo calls initiated by iproute2 or libvirt. While we allow the PF/host to change the VF admin mac address from zero to a valid unicast mac, we do not allow restoring the VF admin mac to zero. We currently only allow changing this mac to a different unicast mac. This leads to problems when libvirt scripts are used to deal with VF mac addresses, and libvirt attempts to revoke the mac so this host will not use it anymore. Fix this by allowing resetting a VF administrative MAC back to zero. Fixes: 8f7ba3ca ('net/mlx4: Add set VF mac address support') Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Reported-by:
Moshe Levi <moshele@mellanox.com> Signed-off-by:
-
Guillaume Nault authored
commit 6faac63a upstream. Add missing rtnl_unlock() in the error path of ppp_create_interface(). Fixes: 58a89eca ("ppp: fix lockdep splat in ppp_dev_uninit()") Signed-off-by:
Guillaume Nault <g.nault@alphalink.fr> Signed-off-by:
-
Eryu Guan authored
commit 6ffe77ba upstream. In commit bcff2488 ("ext4: don't read blocks from disk after extents being swapped") bh is not updated correctly in the for loop and wrong data has been written to disk. generic/324 catches this on sub-page block size ext4. Fixes: bcff2488 ("ext4: don't read blocks from disk after extentsbeing swapped") Signed-off-by:
Eryu Guan <guaneryu@gmail.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Konstantin Khlebnikov authored
commit 9bdfb3b7 upstream. Currently it's converted into msecs, thus HZ=1000 intact. Signed-off-by:
Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Fixes: 740b0f18 ("tcp: switch rtt estimations to usec resolution") Signed-off-by:
-
Douglas Miller authored
commit a69bf3c5 upstream. The adapter->pcicfg resource is either mapped via pci_iomap() or derived from adapter->db. During be_remove() this resource was ignored and so could remain mapped after remove. Add a flag to track whether adapter->pcicfg was mapped or not, then use that flag in be_unmap_pci_bars() to unmap if required. Fixes: 25848c90 ("use PCI MMIO read instead of config read for errors") Signed-off-by:
Douglas Miller <dougmill@linux.vnet.ibm.com> Signed-off-by:
-
Eric Dumazet authored
commit a9d99ce2 upstream. If final packet (ACK) of 3WHS is lost, it appears we do not properly account the following incoming segment into tcpi_segs_in While we are at it, starts segs_in with one, to count the SYN packet. We do not yet count number of SYN we received for a request sock, we might add this someday. packetdrill script showing proper behavior after fix : // Tests tcpi_segs_in when 3rd packet (ACK) of 3WHS is lost 0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3 +0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0 +0 bind(3, ..., ...) = 0 +0 listen(3, 1) = 0 +0 < S 0:0(0) win 32792 <mss 1000,sackOK,nop,nop> +0 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK> +.020 < P. 1:1001(1000) ack 1 win 32792 +0 accept(3, ..., ...) = 4 +.000 %{ assert tcpi_segs_in == 2, 'tcpi_segs_in=%d' % tcpi_segs_in }% Fixes: 2efd055c ("tcp: add tcpi_segs_in and tcpi_segs_out to tcp_info") Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
James Hogan authored
commit d825c06b upstream. When calculate_cpu_foreign_map() recalculates the cpu_foreign_map cpumask it uses the local variable temp_foreign_map without initialising it to zero. Since the calculation only ever sets bits in this cpumask any existing bits at that memory location will remain set and find their way into cpu_foreign_map too. This could potentially lead to cache operations suboptimally doing smp calls to multiple VPEs in the same core, even though the VPEs share primary caches. Therefore initialise temp_foreign_map using cpumask_clear() before use. Fixes: cccf34e9 ("MIPS: c-r4k: Fix cache flushing for MT cores") Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/12759/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Robert Jarzmik authored
commit f1692127 upstream. While testing audio with pxa2xx-ac97, underrun were happening while the user application was correctly feeding the music. Debug proved that the cyclic transfer is not cyclic, ie. the last descriptor did not loop on the first. Another issue is that the descriptor length was always set to 8192, because of an trivial operator issue. This was tested on a pxa27x platform. Fixes: a57e16cf ("dmaengine: pxa: add pxa dmaengine driver") Reported-by:
Vasily Khoruzhick <anarsoul@gmail.com> Tested-by:
Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Or Gerlitz authored
commit 11d8d645 upstream. According to IBTA spec v1.3 section 12.7.19, QPs should use GRH when the path returned by the SA has hop-limit > 0. Currently, we do that only for the > 1 case, fix that. Fixes: 6d969a47 ('IB/sa: Add ib_init_ah_from_path()') Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by:
Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> [ kamal: backport to 4.2-stable: context ] Signed-off-by:
-
Hauke Mehrtens authored
commit 7a50e468 upstream. The MIPS_GIC_IPI should only be selected when MIPS_GIC is also selected, otherwise it results in a compile error. smp-gic.c uses some functions from include/linux/irqchip/mips-gic.h like plat_ipi_call_int_xlate() which are only added to the header file when MIPS_GIC is set. The Lantiq SoC does not use the GIC, but supports SMP. The calls top the functions from smp-gic.c are already protected by some #ifdefs The first part of this was introduced in commit 72e20142 ("MIPS: Move GIC IPI functions out of smp-cmp.c") Signed-off-by:
Hauke Mehrtens <hauke@hauke-m.de> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/12774/Signed-off-by:
-
Ludovic Desroches authored
commit 25c5e962 upstream. When computing the residue we need two pieces of information: the current descriptor and the remaining data of the current descriptor. To get that information, we need to read consecutively two registers but we can't do it in an atomic way. For that reason, we have to check manually that current descriptor has not changed. Signed-off-by:
Ludovic Desroches <ludovic.desroches@atmel.com> Suggested-by:
Cyrille Pitchen <cyrille.pitchen@atmel.com> Reported-by:
David Engraf <david.engraf@sysgo.com> Tested-by:
-
Paolo Bonzini authored
commit 844a5fe2 upstream. Yes, all of these are needed. :) This is admittedly a bit odd, but kvm-unit-tests access.flat tests this if you run it with "-cpu host" and of course ept=0. KVM runs the guest with CR0.WP=1, so it must handle supervisor writes specially when pte.u=1/pte.w=0/CR0.WP=0. Such writes cause a fault when U=1 and W=0 in the SPTE, but they must succeed because CR0.WP=0. When KVM gets the fault, it sets U=0 and W=1 in the shadow PTE and restarts execution. This will still cause a user write to fault, while supervisor writes will succeed. User reads will fault spuriously now, and KVM will then flip U and W again in the SPTE (U=1, W=0). User reads will be enabled and supervisor writes disabled, going back to the originary situation where supervisor writes fault spuriously. When SMEP is in effect, however, U=0 will enable kernel execution of this page. To avoid this, KVM also sets NX=1 in the shadow PTE together with U=0. If the guest has not enabled NX, the result is a continuous stream of page faults due to the NX bit being reserved. The fix is to force EFER.NX=1 even if the CPU is taking care of the EFER switch. (All machines with SMEP have the CPU_LOAD_IA32_EFER vm-entry control, so they do not use user-return notifiers for EFER---if they did, EFER.NX would be forced to the same value as the host). There is another bug in the reserved bit check, which I've split to a separate patch for easier application to stable kernels. Cc: Andy Lutomirski <luto@amacapital.net> Reviewed-by:
Xiao Guangrong <guangrong.xiao@linux.intel.com> Fixes: f6577a5fSigned-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit dc17147d upstream. Commit f3775549 ("tracepoints: Do not trace when cpu is offline") added a check to make sure that tracepoints only get called when the cpu is online, as it uses rcu_read_lock_sched() for protection. Commit 3a630178 ("tracing: generate RCU warnings even when tracepoints are disabled") added lockdep checks (including rcu checks) for events that are not enabled to catch possible RCU issues that would only be triggered if a trace event was enabled. Commit f3775549 only stopped the warnings when the trace event was enabled but did not prevent warnings if the trace event was called when disabled. To fix this, the cpu online check is moved to where the condition is added to the trace event. This will place the cpu online check in all places that it may be used now and in the future. Fixes: f3775549 ("tracepoints: Do not trace when cpu is offline") Fixes: 3a630178 ("tracing: generate RCU warnings even when tracepoints are disabled") Reported-by:
Sudeep Holla <sudeep.holla@arm.com> Tested-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Ard Biesheuvel authored
commit 36e5cd6b upstream. Commit dfd55ad8 ("arm64: vmemmap: use virtual projection of linear region") fixed an issue where the struct page array would overflow into the adjacent virtual memory region if system RAM was placed so high up in physical memory that its addresses were not representable in the build time configured virtual address size. However, the fix failed to take into account that the vmemmap region needs to be relatively aligned with respect to the sparsemem section size, so that a sequence of page structs corresponding with a sparsemem section in the linear region appears naturally aligned in the vmemmap region. So round up vmemmap to sparsemem section size. Since this essentially moves the projection of the linear region up in memory, also revert the reduction of the size of the vmemmap region. Fixes: dfd55ad8 ("arm64: vmemmap: use virtual projection of linear region") Tested-by:
Mark Langsdorf <mlangsdo@redhat.com> Tested-by:
David Daney <david.daney@cavium.com> Tested-by:
Robert Richter <rrichter@cavium.com> Acked-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Radim Krčmář authored
commit 7099e2e1 upstream. Linux guests on Haswell (and also SandyBridge and Broadwell, at least) would crash if you decided to run a host command that uses PEBS, like perf record -e 'cpu/mem-stores/pp' -a This happens because KVM is using VMX MSR switching to disable PEBS, but SDM [2015-12] 18.4.4.4 Re-configuring PEBS Facilities explains why it isn't safe: When software needs to reconfigure PEBS facilities, it should allow a quiescent period between stopping the prior event counting and setting up a new PEBS event. The quiescent period is to allow any latent residual PEBS records to complete its capture at their previously specified buffer address (provided by IA32_DS_AREA). There might not be a quiescent period after the MSR switch, so a CPU ends up using host's MSR_IA32_DS_AREA to access an area in guest's memory. (Or MSR switching is just buggy on some models.) The guest can learn something about the host this way: If the guest doesn't map address pointed by MSR_IA32_DS_AREA, it results in #PF where we leak host's MSR_IA32_DS_AREA through CR2. After that, a malicious guest can map and configure memory where MSR_IA32_DS_AREA is pointing and can therefore get an output from host's tracing. This is not a critical leak as the host must initiate with PEBS tracing and I have not been able to get a record from more than one instruction before vmentry in vmx_vcpu_run() (that place has most registers already overwritten with guest's). We could disable PEBS just few instructions before vmentry, but disabling it earlier shouldn't affect host tracing too much. We also don't need to switch MSR_IA32_PEBS_ENABLE on VMENTRY, but that optimization isn't worth its code, IMO. (If you are implementing PEBS for guests, be sure to handle the case where both host and guest enable PEBS, because this patch doesn't.) Fixes: 26a4f3c0 ("perf/x86: disable PEBS on a guest entry.") Reported-by:
Jiří Olša <jolsa@redhat.com> Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Al Viro authored
commit f9381284 upstream. d_instantiate(new_dentry, old_inode) is absolutely wrong thing to do - it will oops if new_dentry used to be positive, for starters. What we need is d_invalidate() the target and be done with that. Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Al Viro authored
commit 803c0012 upstream. Failing to allocate an inode for child means that cache for *parent* is incompletely populated. So it's parent directory inode ('dir') that needs NCPI_DIR_CACHE flag removed, *not* the child inode ('inode', which is what we'd failed to allocate in the first place). Fucked-up-in: commit 5e993e25 ("ncpfs: get rid of d_validate() nonsense") Fucked-up-by:
-
Paul Mackerras authored
commit ccec4456 upstream. Thomas Huth discovered that a guest could cause a hard hang of a host CPU by setting the Instruction Authority Mask Register (IAMR) to a suitable value. It turns out that this is because when the code was added to context-switch the new special-purpose registers (SPRs) that were added in POWER8, we forgot to add code to ensure that they were restored to a sane value on guest exit. This adds code to set those registers where a bad value could compromise the execution of the host kernel to a suitable neutral value on guest exit. Fixes: b005255eReported-by:
Thomas Huth <thuth@redhat.com> Reviewed-by:
David Gibson <david@gibson.dropbear.id.au> Signed-off-by:
Paul Mackerras <paulus@samba.org> Signed-off-by:
-
Linus Torvalds authored
commit 256faedc upstream. This reverts commit dbb17a21. It turns out that commit can cause problems for systems with multiple GPUs, and causes X to hang on at least a HP Pavilion dv7 with hybrid graphics. This got noticed originally in 4.4.4, where this patch had already gotten back-ported, but 4.5-rc7 was verified to have the same problem. Alexander Deucher says: "It looks like you have a muxed system so I suspect what's happening is that one of the display is being reported as connected for both the IGP and the dGPU and then the desktop environment gets confused or there some sort problem in the detect functions since the mux is not switched to the dGPU. I don't see an easy fix unless Dave has any ideas. I'd say just revert for now" Reported-by:
Jörg-Volker Peetz <jvpeetz@web.de> Acked-by:
Alexander Deucher <Alexander.Deucher@amd.com> Cc: Dave Airlie <airlied@gmail.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Krzysztof =?utf-8?Q?Ha=C5=82asa?= authored
commit 54c6e2dd upstream. pci_create_root_bus() passes a "parent" pointer to pci_bus_assign_domain_nr(). When CONFIG_PCI_DOMAINS_GENERIC is defined, pci_bus_assign_domain_nr() dereferences that pointer. Many callers of pci_create_root_bus() supply a NULL "parent" pointer, which leads to a NULL pointer dereference error. 7c674700 ("PCI: Move domain assignment from arm64 to generic code") moved the "parent" dereference from arm64 to generic code. Only arm64 used that code (because only arm64 defined CONFIG_PCI_DOMAINS_GENERIC), and it always supplied a valid "parent" pointer. Other arches supplied NULL "parent" pointers but didn't defined CONFIG_PCI_DOMAINS_GENERIC, so they used a no-op version of pci_bus_assign_domain_nr(). 8c7d1474 ("ARM/PCI: Move to generic PCI domains") defined CONFIG_PCI_DOMAINS_GENERIC on ARM, and many ARM platforms use pci_common_init(), which supplies a NULL "parent" pointer. These platforms (cns3xxx, dove, footbridge, iop13xx, etc.) crash with a NULL pointer dereference like this while probing PCI: Unable to handle kernel NULL pointer dereference at virtual address 000000a4 PC is at pci_bus_assign_domain_nr+0x10/0x84 LR is at pci_create_root_bus+0x48/0x2e4 Kernel panic - not syncing: Attempted to kill init! [bhelgaas: changelog, add "Reported:" and "Fixes:" tags] Reported: http://forum.doozan.com/read.php?2,17868,22070,quote=1 Fixes: 8c7d1474 ("ARM/PCI: Move to generic PCI domains") Fixes: 7c674700 ("PCI: Move domain assignment from arm64 to generic code") Signed-off-by:
Krzysztof Hałasa <khalasa@piap.pl> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Acked-by:
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by:
-
Mugunthan V N authored
commit 0f514e69 upstream. Errata id: i877 Description: ------------ The RGMII 1000 Mbps Transmit timing is based on the output clock (rgmiin_txc) being driven relative to the rising edge of an internal clock and the output control/data (rgmiin_txctl/txd) being driven relative to the falling edge of an internal clock source. If the internal clock source is allowed to be static low (i.e., disabled) for an extended period of time then when the clock is actually enabled the timing delta between the rising edge and falling edge can change over the lifetime of the device. This can result in the device switching characteristics degrading over time, and eventually failing to meet the Data Manual Delay Time/Skew specs. To maintain RGMII 1000 Mbps IO Timings, SW should minimize the duration that the Ethernet internal clock source is disabled. Note that the device reset state for the Ethernet clock is "disabled". Other RGMII modes (10 Mbps, 100Mbps) are not affected Workaround: ----------- If the SoC Ethernet interface(s) are used in RGMII mode at 1000 Mbps, SW should minimize the time the Ethernet internal clock source is disabled to a maximum of 200 hours in a device life cycle. This is done by enabling the clock as early as possible in IPL (QNX) or SPL/u-boot (Linux/Android) by setting the register CM_GMAC_CLKSTCTRL[1:0]CLKTRCTRL = 0x2:SW_WKUP. So, do not allow to gate the cpsw clocks using ti,no-idle property in cpsw node assuming 1000 Mbps is being used all the time. If someone does not need 1000 Mbps and wants to gate clocks to cpsw, this property needs to be deleted in their respective board files. Signed-off-by:
Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by:
Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by:
Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by:
Paul Walmsley <paul@pwsan.com> Signed-off-by:
-
Lokesh Vutla authored
commit 2e18f5a1 upstream. Introduce a dt property, ti,no-idle, that prevents an IP to idle at any point. This is to handle Errata i877, which tells that GMAC clocks cannot be disabled. Acked-by:
Roger Quadros <rogerq@ti.com> Tested-by:
Sekhar Nori <nsekhar@ti.com> Signed-off-by:
Dave Gerlach <d-gerlach@ti.com> Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Nicholas Bellinger authored
commit 7f54ab5f upstream. This patch fixes a recent ABORT_TASK regression associated with commit febe562c, where a left-over target_put_sess_cmd() would still be called when __target_check_io_state() detected a command has already been completed, and explicit ABORT must be avoided. Note commit febe562c dropped the local kref_get_unless_zero() check in core_tmr_abort_task(), but did not drop this extra corresponding target_put_sess_cmd() in the failure path. So go ahead and drop this now bogus target_put_sess_cmd(), and avoid this potential use-after-free. Reported-by:
Dan Lane <dracodan@gmail.com> Cc: Quinn Tran <quinn.tran@qlogic.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: Andy Grover <agrover@redhat.com> Cc: Mike Christie <mchristi@redhat.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Richard Weinberger authored
commit e4f6daac upstream. ubi_start_leb_change() allocates too few bytes. ubi_more_leb_change_data() will write up to req->upd_bytes + ubi->min_io_size bytes. Signed-off-by:
Richard Weinberger <richard@nod.at> Reviewed-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by:
-
Maciej W. Rozycki authored
commit e723e3f7 upstream. Avoid sending a partially initialised `siginfo_t' structure along SIGFPE signals issued from `do_ov' and `do_trap_or_bp', leading to information leaking from the kernel stack. Signed-off-by:
Maciej W. Rozycki <macro@imgtec.com> Signed-off-by:
-
Konstantin Khlebnikov authored
commit b81de061 upstream. Overlayfs must update uid/gid after chown, otherwise functions like inode_owner_or_capable() will check user against stale uid. Catched by xfstests generic/087, it chowns file and calls utimes. Signed-off-by:
Konstantin Khlebnikov <koct9i@gmail.com> Signed-off-by:
Miklos Szeredi <miklos@szeredi.hu> Signed-off-by:
-
Konstantin Khlebnikov authored
commit 45d11738 upstream. After rename file dentry still holds reference to lower dentry from previous location. This doesn't matter for data access because data comes from upper dentry. But this stale lower dentry taints dentry at new location and turns it into non-pure upper. Such file leaves visible whiteout entry after remove in directory which shouldn't have whiteouts at all. Overlayfs already tracks pureness of file location in oe->opaque. This patch just uses that for detecting actual path type. Comment from Vivek Goyal's patch: Here are the details of the problem. Do following. $ mkdir upper lower work merged upper/dir/ $ touch lower/test $ sudo mount -t overlay overlay -olowerdir=lower,upperdir=upper,workdir= work merged $ mv merged/test merged/dir/ $ rm merged/dir/test $ ls -l merged/dir/ /usr/bin/ls: cannot access merged/dir/test: No such file or directory total 0 c????????? ? ? ? ? ? test Basic problem seems to be that once a file has been unlinked, a whiteout has been left behind which was not needed and hence it becomes visible. Whiteout is visible because parent dir is of not type MERGE, hence od->is_real is set during ovl_dir_open(). And that means ovl_iterate() passes on iterate handling directly to underlying fs. Underlying fs does not know/filter whiteouts so it becomes visible to user. Why did we leave a whiteout to begin with when we should not have. ovl_do_remove() checks for OVL_TYPE_PURE_UPPER() and does not leave whiteout if file is pure upper. In this case file is not found to be pure upper hence whiteout is left. So why file was not PURE_UPPER in this case? I think because dentry is still carrying some leftover state which was valid before rename. For example, od->numlower was set to 1 as it was a lower file. After rename, this state is not valid anymore as there is no such file in lower. Signed-off-by:
Viktor Stanchev <me@viktorstanchev.com> Suggested-by:
Vivek Goyal <vgoyal@redhat.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=109611Acked-by:
-
Rui Wang authored
commit ce9113bb upstream. ovl_remove_upper() should do d_drop() only after it successfully removes the dir, otherwise a subsequent getcwd() system call will fail, breaking userspace programs. This is to fix: https://bugzilla.kernel.org/show_bug.cgi?id=110491Signed-off-by:
Rui Wang <rui.y.wang@intel.com> Reviewed-by:
-
Konstantin Khlebnikov authored
commit b5891cfa upstream. This adds missing .d_select_inode into alternative dentry_operations. Signed-off-by:
Nikolay Borisov <kernel@kyup.com> Tested-by:
-
Simon South authored
commit 02322ac9 upstream. This patch applies the microphone-related fix created for the Acer Aspire E1-572 to the E1-472 as well, as it uses the same Realtek ALC282 CODEC and demonstrates the same issues. This patch allows an external, headset microphone to be used and limits the gain on the (quite noisy) internal microphone. Signed-off-by:
Simon South <simon@simonsouth.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Todd E Brandt authored
commit 92f9e179 upstream. Pause/unpause graph tracing around do_suspend_lowlevel as it has inconsistent call/return info after it jumps to the wakeup vector. The graph trace buffer will otherwise become misaligned and may eventually crash and hang on suspend. To reproduce the issue and test the fix: Run a function_graph trace over suspend/resume and set the graph function to suspend_devices_and_enter. This consistently hangs the system without this fix. Signed-off-by:
Todd Brandt <todd.e.brandt@linux.intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Arindam Nath authored
commit 0b39c531 upstream. In amdgpu_connector_hotplug(), we need to start DP link training only after we have received DPCD. The function amdgpu_atombios_dp_get_dpcd() returns non-zero value only when an error condition is met, otherwise returns zero. So in case the function encounters an error, we need to skip rest of the code and return from amdgpu_connector_hotplug() immediately. Only when we are successfull in reading DPCD pin, we should carry on with turning-on the monitor. Signed-off-by:
Arindam Nath <arindam.nath@amd.com> Signed-off-by:
-
Alex Deucher authored
commit 5e031d9f upstream. On CI, we need to see if the number of crtcs changes to determine whether or not we need to upload the mclk table again. In practice we don't currently upload the mclk table again after the initial load. The only reason you would would be to add new states, e.g., for arbitrary mclk setting which is not currently supported. Acked-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
-
Alex Deucher authored
commit eda1d1cf upstream. On CI, we need to see if the number of crtcs changes to determine whether or not we need to upload the mclk table again. In practice we don't currently upload the mclk table again after the initial load. The only reason you would would be to add new states, e.g., for arbitrary mclk setting which is not currently supported. Acked-by:
Jordan Lazare <Jordan.Lazare@amd.com> Acked-by:
-
Bjørn Mork authored
commit 04fdbc82 upstream. The MC74xx and EM74xx modules use different IDs by default, according to the Lenovo EM7455 driver for Windows. Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Timothy Pearson authored
commit 2d02b8bd upstream. During DRAM initialization on certain ASpeed devices, an incorrect bit (bit 10) was checked in the "SDRAM Bus Width Status" register to determine DRAM width. Query bit 6 instead in accordance with the Aspeed AST2050 datasheet v1.05. Signed-off-by:
Timothy Pearson <tpearson@raptorengineeringinc.com> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Helge Deller authored
commit 98e8b6c9 upstream. Mike Frysinger reported that his ptrace testcase showed strange behaviour on parisc: It was not possible to avoid a syscall and the return value of a syscall couldn't be changed. To modify a syscall number, we were missing to save the new syscall number to gr20 which is then picked up later in assembly again. The effect that the return value couldn't be changed is a side-effect of another bug in the assembly code. When a process is ptraced, userspace expects each syscall to report entrance and exit of a syscall. If a syscall number was given which doesn't exist, we jumped to the normal syscall exit code instead of informing userspace that the (non-existant) syscall exits. This unexpected behaviour confuses userspace and thus the bug was misinterpreted as if we can't change the return value. This patch fixes both problems and was tested on 64bit kernel with 32bit userspace. Signed-off-by:
Helge Deller <deller@gmx.de> Cc: Mike Frysinger <vapier@gentoo.org> Tested-by:
Mike Frysinger <vapier@gentoo.org> Signed-off-by:
-
Takashi Iwai authored
commit 197b958c upstream. The OSS sequencer client tries to drain the pending events at releasing. Unfortunately, as spotted by syzkaller fuzzer, this may lead to an unkillable process state when the event has been queued at the far future. Since the process being released can't be signaled any longer, it remains and waits for the echo-back event in that far future. Back to history, the draining feature was implemented at the time we misinterpreted POSIX definition for blocking file operation. Actually, such a behavior is superfluous at release, and we should just release the device as is instead of keeping it up forever. This patch just removes the draining call that may block the release for too long time unexpectedly. BugLink: http://lkml.kernel.org/r/CACT4Y+Y4kD-aBGj37rf-xBw9bH3GMU6P+MYg4W1e-s-paVD2pg@mail.gmail.comReported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
-
