Refactor the stats len computation code to make it easier
to add new stats counters.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The existence of the DT port node is the first thing checked
at probe time, and probing won't reach this point if the node
is missing.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When pktgen is used to measure the performance of dev_queue_xmit()
packet handling in the core, it is preferable to not hand down
packets to a low-level Ethernet driver as it would distort the
measurements.

Allow using pktgen on the loopback device, thus constraining
measurements to core code.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of manually iterating over entries, use flow_action_for_each
helper. Move the helper and wrap it to fit to 80 cols on the way.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jose Abreu says:

====================
net: Add support for Synopsys DesignWare XPCS

This adds support for Synopsys DesignWare XPCS in net subsystem and
integrates it into stmmac.

At 1/8, we start by removing the limitation of stmmac selftests that needed
a PHY to pass all the tests.

Then at 2/8 we use some helpers in stmmac so that some code can be
simplified.

At 3/8, we fallback to dev_fwnode() so that PCI based setups wich may
not have CONFIG_OF can still use FW node.

At 4/8, we adapt stmmac to the new PHYLINK changes as suggested by Russell
King.

We proceed by doing changes in PHYLINK in order to support XPCS: At 5/8 we
add some missing speeds that USXGMII supports and at 6/8 we check if
Autoneg is supported after initial parameters are validated.

Support for XPCS is finally introduced at 7/8, along with the usage of it
in stmmac driver at 8/8.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds all the necessary logic so that stmmac can be used with Synopsys
DesignWare XPCS.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Synopsys DesignWare XPCS is an MMD that can manage link status,
auto-negotiation, link training, ...

In this commit we add basic support for XPCS using USXGMII interface and
Clause 73 Auto-negotiation.

This is highly tied with PHYLINK and can't be used without it. A given
ethernet driver can use the provided callbacks to add the support for
XPCS.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We may have cases where MAC or PCS do not support Autoneg. Check if it
is supported after validate callback is called.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

USXGMII also supports these missing backplane speeds.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert the stmmac ethernet driver to use the finalised link parameters
in mac_link_up() rather than the parameters in mac_config().
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When CONFIG_OF is not enabled, of_fwnode_handle() will return NULL, even
though we can have a FW handle from a given device.

Fallback to dev_fwnode() helper if needed.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the linkmode_and()/linkmode_andnot() helpers to simplify the code.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a PHY is not attached, we can still run the tests with MAC loopback
mode. Return -EOPNOTSUPP error code in PHY loopback test so that global
status is not a failure.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2020-03-09

This series provides updates to mlx5 driver:

1) Use vport metadata matching only when mandatory
2) Introduce root flow table and ethtool steering for uplink representors
3) Expose port speed via FW when link modes are not available
3) Misc cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Huazhong Tan says:

====================
net: hns3: misc updates for -net-next

This series includes some misc updates for the HNS3 ethernet driver.

[patch 1] fixes some mixed type operation warning.
[patch 2] renames a macro to make it more readable.
[patch 3 & 4]  removes some unnecessary code.
[patch 5] adds check before assert VF reset to prevent some unsuitable
error log.
[patch 6 - 9] some modifications related to printing.

Change log:
V1->V2: fixes a wrong print format in [patch 1] suggested by Jian Shen.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since kernel already has logs after kzalloc fails,
it's unnecessary to print duplicate logs. So this
patch deletes these logs.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch modifies some printing relating to reset issue.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a local variable to save the command code in
some dump cases which need to modify the command code, then
the failing command code can be print out for debugging.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When received an unknown vector 0 interrupt, there is not a
helpful information for user to realize that now. So this patch
prints out the value of the status register for this case, and
uses dev_info() instead of dev_dbg() in hclge_check_event_cause().
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When setting VF's MAC from PF, if the VF driver not loaded, the
firmware will return error to PF.

So PF should check whether VF is alive before sending message to
VF when setting VF's MAC.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In hclge_add_mc_addr_common() and hclge_rm_mc_addr_common(),
variable req had been set as "0" by memset(), so it's unnecessary
to set .entry_type field as "0" with hnae3_set_bit() again.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In hclge_handle_hw_ras_error(), it is unnecessary to check
HCLGE_STATE_RST_HANDLING flag, because the reset priority
has been ensured by the process itself.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The name of macro HCLGE_MAX_NCL_CONFIG_LENGTH is inaccurate,
this patch renames it to HCLGE_NCL_CONFIG_LENGTH_IN_EACH_CMD.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch cleans up some incorrect type in assignment reported by sparse
and compiler.
The warning as below:
- warning : restricted __le16 degrades to integer
- warning : cast from restricted __le32
- warning : cast from restricted __be32
- warning : cast from restricted __be16
and "mixed operation".
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shannon Nelson says:

====================
ionic updates

This is a set of small updates for the Pensando ionic driver, some
from internal work, some a result of mailing list discussions.

v4 - don't register mgmt device netdev
v3 - changed __attribute__(packed)) to __packed
v2 - removed print from ionic_init_module()
====================
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the default kernel version in ethtool drv_info output
and drop the module version.

Cc: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for the management port device id.  This is to
capture the device and set it up for devlink use, but not set
it up for network operations.  We still use a netdev object
in order to use the napi infrasucture for processing adminq
and notifyq messages, we just don't register the netdev.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Print the PCI bus lane information so people can keep an
eye out for poor configurations that might not support
the advertised speed.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

We can disable rxhashing by setting rss_types to 0.  The user
can toggle this with "ethtool -K <ethX> rxhash off|on",
which calls into the .ndo_set_features callback with the
NETIF_F_RXHASH feature bit set or cleared.  This patch adds
a check for that bit and updates the FW if necessary.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the unused flags field and and fix the bitflag names
to include the _F_ flag hint.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Spreading the interrupts across the CPU cores is good for load
balancing, but not necessarily as good when using a CPU/core
that is not part of the NUMA local CPU.  If it can be localized,
the kernel's cpumask_local_spread() service will pick a core
that is on the node close to the PCI device.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the misguided "#pragma packed" with tags on each
struct/union definition that actually needs it.  This is safer
and more efficient on the various compilers and architectures.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the basic ionic interface works but the lif creation fails,
don't fail the probe.  This will allow us to use the driver to
help inspect the hw/fw/pci interface for debugging purposes.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Westphal says:

====================
mptcp: don't auto-adjust rcvbuf size if locked

The mptcp receive buffer is auto-sized based on the subflow receive
buffer.  Don't do this if userspace specfied a value via SO_RCVBUF
setsockopt.

Also update selftest program to provide a new option to set a fixed
size.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The mptcp rcvbuf size is adjusted according to the subflow rcvbuf size.
This should not be done if userspace did set a fixed value.

Fixes: 600911ff ("mptcp: add rmem queue accounting")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

allows to run the tests with fixed receive buffer by passing
"-R <value>" to mptcp_connect.sh.

While at it, add a default 10 second poll timeout so the "-t"
becomes optional -- this makes mptcp_connect simpler to use
during manual testing.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for configuring port mirroring through the cls_matchall
classifier. We do a full ingress and/or egress capture towards a
capture port.
MT7530 supports one monitor port and multiple mirrored ports.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
This cleanup patchset includes the following patches:

 - bump version strings, by Simon Wunderlich

 - Avoid RCU list-traversal in spinlock, by Sven Eckelmann

 - Replace zero-length array with flexible-array member,
   by Gustavo A. R. Silva
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
r8169: series with improvements to rtl_tx

This series includes few improvements to rtl_tx().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Until ae84bc18 ("r8169: don't use bit LastFrag in tx descriptor
after send") we used to access another bit in the descriptor, therefore
it seems the barrier was needed. Since this commit DescOwn is the
only bit we're interested in, so the barrier isn't needed any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>