The udp_ip4_ind bit is set only for IPv4 UDP non-fragmented packets
so that the hardware can flip the checksum to 0xFFFF if the computed
checksum is 0 per RFC768.

However, this bit had to be set for IPv6 UDP non fragmented packets
as well per hardware requirements. Otherwise, IPv6 UDP packets
with computed checksum as 0 were transmitted by hardware and were
dropped in the network.

In addition to setting this bit for IPv6 UDP, the field is also
appropriately renamed to udp_ind as part of this change.

Fixes: 5eb5f860 ("net: qualcomm: rmnet: Add support for TX checksum offload")
Cc: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip4ip6/ip6ip6 tunnels run iptunnel_handle_offloads on xmit which
can cause a possible use-after-free accessing iph/ipv6h pointer
since the packet will be 'uncloned' running pskb_expand_head if
it is a cloned gso skb.

Fixes: 0e9a7095 ("ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets")
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure the delayed work for stats update is not pending before
wq destruction.
This fixes the module unload path.
The issue is there since day 1.

Fixes: a556c76a ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The hw_ver field was initialized to zero. Return the chip revision.
This is relevant for rdma driver.
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The BroadMobi BM818 M.2 card uses the QMI protocol
Signed-off-by: Bob Ham <bob.ham@puri.sm>
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
pull-request: bpf 2019-07-25

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) fix segfault in libbpf, from Andrii.

2) fix gso_segs access, from Eric.

3) tls/sockmap fixes, from Jakub and John.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We need the same checks introduced by commit cb9f1b78
("ip: validate header length on virtual device xmit") for
ipip tunnel.

Fixes: cb9f1b78 ("ip: validate header length on virtual device xmit")
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6_flowlabel and ipv6_flowlabel_mgr are missing from
gitignore.  Quentin points out that the original
commit 3fb321fd ("selftests/net: ipv6 flowlabel")
did add ignore entries, they are just missing the "ipv6_"
prefix.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 3968d389 ("bnx2x: Fix Multi-Cos.") which enabled multi-cos
feature after prolonged time in driver added some regression causing
numerous issues (sudden reboots, tx timeout etc.) reported by customers.
We plan to backout this commit and submit proper fix once we have root
cause of issues reported with this feature enabled.

Fixes: 3968d389 ("bnx2x: Fix Multi-Cos.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fm_set_max_frm() existed in the Freescale SDK as a callback for an
early_param. When this code was ported to the upstream kernel the
early_param was converted to a module_param making the reference to the
function incorrect. The rest of the comment already does a good job of
explaining the parameter so removing the reference to the non-existent
function seems like the best thing to do.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>

devm_kzalloc may fail and return NULL. So the null check is needed.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

devm_kzalloc may fail and return null. So the null check is needed.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- v1 -> v2: Move skb_set_owner_w to __tun_build_skb to reduce patch size

Small packets going out of a tap device go through an optimized code
path that uses build_skb() rather than sock_alloc_send_pskb(). The
latter calls skb_set_owner_w(), but the small packet code path does not.

The net effect is that small packets are not owned by the userland
application's socket (e.g. QEMU), while large packets are.
This can be seen with a TCP session, where packets are not owned when
the window size is small enough (around PAGE_SIZE), while they are once
the window grows (note that this requires the host to support virtio
tso for the guest to offload segmentation).
All this leads to inconsistent behaviour in the kernel, especially on
netfilter modules that uses sk->socket (e.g. xt_owner).

Fixes: 66ccbc9c ("tap: use build_skb() for small packet")
Signed-off-by: Alexis Bauvin <abauvin@scaleway.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Leon Romanovsky says:

====================
DIM fixes for 5.3

Those two fixes for recently merged DIM patches, both exposed through
RDMa DIM usage.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

DIM causes to the following warnings during kernel compilation
which indicates that tx_profile and rx_profile are supposed to
be declared in *.c and not in *.h files.

In file included from ./include/rdma/ib_verbs.h:64,
                 from ./include/linux/mlx5/device.h:37,
                 from ./include/linux/mlx5/driver.h:51,
                 from ./include/linux/mlx5/vport.h:36,
                 from drivers/infiniband/hw/mlx5/ib_virt.c:34:
./include/linux/dim.h:326:1: warning: _tx_profile_ defined but not used [-Wunused-const-variable=]
  326 | tx_profile[DIM_CQ_PERIOD_NUM_MODES][NET_DIM_PARAMS_NUM_PROFILES] = {
      | ^~~~~~~~~~
./include/linux/dim.h:320:1: warning: _rx_profile_ defined but not used [-Wunused-const-variable=]
  320 | rx_profile[DIM_CQ_PERIOD_NUM_MODES][NET_DIM_PARAMS_NUM_PROFILES] = {
      | ^~~~~~~~~~

Fixes: 4f75da36 ("linux/dim: Move implementation to .c files")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While using net_dim, a dim_sample was used without ever initializing the
comps value. Added use of DIV_ROUND_DOWN_ULL() to prevent potential
overflow, it should not be a problem to save the final result in an int
because after the division by epms the value should not be larger than a
few thousand.

[ 1040.127124] UBSAN: Undefined behaviour in lib/dim/dim.c:78:23
[ 1040.130118] signed integer overflow:
[ 1040.131643] 134718714 * 100 cannot be represented in type 'int'

Fixes: 398c2b05 ("linux/dim: Add completions count to dim_sample")
Signed-off-by: Yamin Friedman <yaminf@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

act_ife at least requires TCA_IFE_PARMS, so we have to bail out
when there is no attribute passed in.

Reported-by: syzbot+fbb5b288c9cb6a2eeac4@syzkaller.appspotmail.com
Fixes: ef6980b6 ("introduce IFE action")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Despite a proper NULL-termination after strncpy(..., ..., IFNAMSIZ - 1),
GCC8 still complains about *expected* string truncation:

  xsk.c:330:2: error: 'strncpy' output may be truncated copying 15 bytes
  from a string of length 15 [-Werror=stringop-truncation]
    strncpy(ifr.ifr_name, xsk->ifname, IFNAMSIZ - 1);

This patch gets rid of the issue altogether by using memcpy instead.
There is no performance regression, as strncpy will still copy and fill
all of the bytes anyway.

v1->v2:
- rebase against bpf tree.

Cc: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

sock_efree() releases the sock refcnt, if we don't hold this refcnt
when setting skb->destructor to it, the refcnt would not be balanced.
This leads to several bug reports from syzbot.

I have checked other users of sock_efree(), all of them hold the
sock refcnt.

Fixes: c8c8218e ("netrom: fix a memory leak in nr_rx_frame()")
Reported-and-tested-by: <syzbot+622bdabb128acc33427d@syzkaller.appspotmail.com>
Reported-and-tested-by: <syzbot+6eaef7158b19e3fec3a0@syzkaller.appspotmail.com>
Reported-and-tested-by: <syzbot+9399c158fcc09b21d0d2@syzkaller.appspotmail.com>
Reported-and-tested-by: <syzbot+a34e5f3d0300163f0c87@syzkaller.appspotmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some functions in the datapath code are factored out so that each
one has a stack frame smaller than 1024 bytes with gcc. However,
when compiling with clang, the functions are inlined more aggressively
and combined again so we get

net/openvswitch/datapath.c:1124:12: error: stack frame size of 1528 bytes in function 'ovs_flow_cmd_set' [-Werror,-Wframe-larger-than=]

Marking both get_flow_actions() and ovs_nla_init_match_and_action()
as 'noinline_for_stack' gives us the same behavior that we see with
gcc, and no warning. Note that this does not mean we actually use
less stack, as the functions call each other, and we still get
three copies of the large 'struct sw_flow_key' type on the stack.

The comment tells us that this was previously considered safe,
presumably since the netlink parsing functions are called with
a known backchain that does not also use a lot of stack space.

Fixes: 9cc9a5cb ("datapath: Avoid using stack larger than 1024.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

I've been spending quite a bit of time fixing and
preventing bit rot in the core TLS code. TLS seems
to only be growing in importance, I'd like to help
ensuring the quality of our implementation.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The memory allocated for the stats array may contain arbitrary data.

Fixes: e4f9ba64 ("net: phy: mscc: add support for VSC8514 PHY.")
Fixes: 00d70d8e ("net: phy: mscc: add support for VSC8574 PHY")
Fixes: a5afc167 ("net: phy: mscc: add support for VSC8584 PHY")
Fixes: f76178dc ("net: phy: mscc: add ethtool statistics counters")
Signed-off-by: Andreas Schwab <schwab@suse.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

SFP modules connected using the SGMII interface have their own PHYs which
are handled by the struct phylink's phydev field. On the other hand, for
the modules connected using 1000Base-X interface that field is not set.

Since commit ce0aa27f ("sfp: add sfp-bus to bridge between network
devices and sfp cages") phylink_start() ends up setting the phydev field
using the sfp-bus infrastructure, which eventually calls phy_start() on it,
and then calling phy_start() again on the same phydev from phylink_start()
itself. Similar call sequence holds for phylink_stop(), only in the reverse
order. This results in WARNs during network interface bringup and shutdown
when a copper SFP module is connected, as phy_start() and phy_stop() are
called twice in a row for the same phy_device:

  % ip link set up dev eth0
  ------------[ cut here ]------------
  called from state UP
  WARNING: CPU: 1 PID: 155 at drivers/net/phy/phy.c:895 phy_start+0x74/0xc0
  Modules linked in:
  CPU: 1 PID: 155 Comm: backend Not tainted 5.2.0+ #1
  NIP:  c0227bf0 LR: c0227bf0 CTR: c004d224
  REGS: df547720 TRAP: 0700   Not tainted  (5.2.0+)
  MSR:  00029000 <CE,EE,ME>  CR: 24002822  XER: 00000000

  GPR00: c0227bf0 df5477d8 df5d7080 00000014 df9d2370 df9d5ac4 1f4eb000 00000001
  GPR08: c061fe58 00000000 00000000 df5477d8 0000003c 100c8768 00000000 00000000
  GPR16: df486a00 c046f1c8 c046eea0 00000000 c046e904 c0239604 db68449c 00000000
  GPR24: e9083204 00000000 00000001 db684460 e9083404 00000000 db6dce00 db6dcc00
  NIP [c0227bf0] phy_start+0x74/0xc0
  LR [c0227bf0] phy_start+0x74/0xc0
  Call Trace:
  [df5477d8] [c0227bf0] phy_start+0x74/0xc0 (unreliable)
  [df5477e8] [c023cad0] startup_gfar+0x398/0x3f4
  [df547828] [c023cf08] gfar_enet_open+0x364/0x374
  [df547898] [c029d870] __dev_open+0xe4/0x140
  [df5478c8] [c029db70] __dev_change_flags+0xf0/0x188
  [df5478f8] [c029dc28] dev_change_flags+0x20/0x54
  [df547918] [c02ae304] do_setlink+0x310/0x818
  [df547a08] [c02b1eb8] __rtnl_newlink+0x384/0x6b0
  [df547c28] [c02b222c] rtnl_newlink+0x48/0x68
  [df547c48] [c02ad7c8] rtnetlink_rcv_msg+0x240/0x27c
  [df547c98] [c02cc068] netlink_rcv_skb+0x8c/0xf0
  [df547cd8] [c02cba3c] netlink_unicast+0x114/0x19c
  [df547d08] [c02cbd74] netlink_sendmsg+0x2b0/0x2c0
  [df547d58] [c027b668] sock_sendmsg_nosec+0x20/0x40
  [df547d68] [c027d080] ___sys_sendmsg+0x17c/0x1dc
  [df547e98] [c027df7c] __sys_sendmsg+0x68/0x84
  [df547ef8] [c027e430] sys_socketcall+0x1a0/0x204
  [df547f38] [c000d1d8] ret_from_syscall+0x0/0x38
  --- interrupt: c01 at 0xfd4e030
      LR = 0xfd4e010
  Instruction dump:
  813f0188 38800000 2b890005 419d0014 3d40c046 5529103a 394aa208 7c8a482e
  3c60c046 3863a1b8 4cc63182 4be009a1 <0fe00000> 48000030 3c60c046 3863a1d0
  ---[ end trace d4c095aeaf6ea998 ]---

and

  % ip link set down dev eth0
  ------------[ cut here ]------------
  called from state HALTED
  WARNING: CPU: 1 PID: 184 at drivers/net/phy/phy.c:858 phy_stop+0x3c/0x88

  <...>

  Call Trace:
  [df581788] [c0228450] phy_stop+0x3c/0x88 (unreliable)
  [df581798] [c022d548] sfp_sm_phy_detach+0x1c/0x44
  [df5817a8] [c022e8cc] sfp_sm_event+0x4b0/0x87c
  [df581848] [c022f04c] sfp_upstream_stop+0x34/0x44
  [df581858] [c0225608] phylink_stop+0x7c/0xe4
  [df581868] [c023c57c] stop_gfar+0x7c/0x94
  [df581888] [c023c5b8] gfar_close+0x24/0x94
  [df5818a8] [c0298688] __dev_close_many+0xdc/0xf8
  [df5818c8] [c029db58] __dev_change_flags+0xd8/0x188
  [df5818f8] [c029dc28] dev_change_flags+0x20/0x54
  [df581918] [c02ae304] do_setlink+0x310/0x818
  [df581a08] [c02b1eb8] __rtnl_newlink+0x384/0x6b0
  [df581c28] [c02b222c] rtnl_newlink+0x48/0x68
  [df581c48] [c02ad7c8] rtnetlink_rcv_msg+0x240/0x27c
  [df581c98] [c02cc068] netlink_rcv_skb+0x8c/0xf0
  [df581cd8] [c02cba3c] netlink_unicast+0x114/0x19c
  [df581d08] [c02cbd74] netlink_sendmsg+0x2b0/0x2c0
  [df581d58] [c027b668] sock_sendmsg_nosec+0x20/0x40
  [df581d68] [c027d080] ___sys_sendmsg+0x17c/0x1dc
  [df581e98] [c027df7c] __sys_sendmsg+0x68/0x84
  [df581ef8] [c027e430] sys_socketcall+0x1a0/0x204
  [df581f38] [c000d1d8] ret_from_syscall+0x0/0x38

  <...>

  ---[ end trace d4c095aeaf6ea999 ]---

SFP modules with the 1000Base-X interface are not affected.

Place explicit calls to phy_start() and phy_stop() before enabling or after
disabling an attached SFP module, where phydev is not yet set (or is
already unset), so they will be made only from the inside of sfp-bus, if
needed.

Fixes: 21796261 ("net: phy: warn if phy_start is called from invalid state")
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-5.3-20190724' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2019-07-24

this is a pull reqeust of 7 patches for net/master.

The first patch is by Rasmus Villemoes add a missing netif_carrier_off() to
register_candev() so that generic netdev trigger based LEDs are initially off.

Nikita Yushchenko's patch for the rcar_canfd driver fixes a possible IRQ storm
on high load.

The patch by Weitao Hou for the mcp251x driver add missing error checking to
the work queue allocation.

Both Wen Yang's and Joakim Zhang's patch for the flexcan driver fix a problem
with the stop-mode.

Stephane Grosjean contributes a patch for the peak_usb driver to fix a
potential double kfree_skb().

The last patch is by YueHaibing and fixes the error path in can-gw's
cgw_module_init() function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since ip6_tnl_parse_tlv_enc_lim() can call pskb_may_pull()
which may change skb->data, so we need to re-load ipv6h at
the right place.

Fixes: 898b2979 ("ip6_gre: Refactor ip6gre xmit codes")
Cc: William Tu <u9012063@gmail.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cleanup testing for error condition.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch add error path for cgw_module_init to avoid possible crash if
some error occurs.

Fixes: c1aabdf3 ("can-gw: add netlink based CAN routing")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

When closing the CAN device while tx skbs are inflight, echo skb could
be released twice. By calling close_candev() before unlinking all
pending tx urbs, then the internal echo_skb[] array is fully and
correctly cleared before the USB write callback and, therefore,
can_get_echo_skb() are called, for each aborted URB.

Fixes: bb478555 ("can: usb: PEAK-System Technik USB adapters driver core")
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

To enter stop mode, the CPU should manually assert a global Stop Mode
request and check the acknowledgment asserted by FlexCAN. The CPU must
only consider the FlexCAN in stop mode when both request and
acknowledgment conditions are satisfied.

Fixes: de3578c1 ("can: flexcan: add self wakeup support")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The gpr_np variable is still being used in dev_dbg() after the
of_node_put() call, which may result in use-after-free.

Fixes: de3578c1 ("can: flexcan: add self wakeup support")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

add error check when workqueue alloc failed, and remove redundant code
to make it clear.

Fixes: e0000163 ("can: Driver for the Microchip MCP251x SPI CAN controllers")
Signed-off-by: Weitao Hou <houweitaoo@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

We have observed rcar_canfd driver entering IRQ storm under high load,
with following scenario:
- rcar_canfd_global_interrupt() in entered due to Rx available,
- napi_schedule_prep() is called, and sets NAPIF_STATE_SCHED in state
- Rx fifo interrupts are masked,
- rcar_canfd_global_interrupt() is entered again, this time due to
  error interrupt (e.g. due to overflow),
- since scheduled napi poller has not yet executed, condition for calling
  napi_schedule_prep() from rcar_canfd_global_interrupt() remains true,
  thus napi_schedule_prep() gets called and sets NAPIF_STATE_MISSED flag
  in state,
- later, napi poller function rcar_canfd_rx_poll() gets executed, and
  calls napi_complete_done(),
- due to NAPIF_STATE_MISSED flag in state, this call does not clear
  NAPIF_STATE_SCHED flag from state,
- on return from napi_complete_done(), rcar_canfd_rx_poll() unmasks Rx
  interrutps,
- Rx interrupt happens, rcar_canfd_global_interrupt() gets called
  and calls napi_schedule_prep(),
- since NAPIF_STATE_SCHED is set in state at this time, this call
  returns false,
- due to that false return, rcar_canfd_global_interrupt() returns
  without masking Rx interrupt
- and this results into IRQ storm: unmasked Rx interrupt happens again
  and again is misprocessed in the same way.

This patch fixes that scenario by unmasking Rx interrupts only when
napi_complete_done() returns true, which means it has cleared
NAPIF_STATE_SCHED in state.

Fixes: dd3bd23e ("can: rcar_canfd: Add Renesas R-Car CAN FD driver")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

CONFIG_CAN_LEDS is deprecated. When trying to use the generic netdev
trigger as suggested, there's a small inconsistency with the link
property: The LED is on initially, stays on when the device is brought
up, and then turns off (as expected) when the device is brought down.

Make sure the LED always reflects the state of the CAN device.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

'channels.max_combined' initialized only on ioctl success and
errno is only valid on ioctl failure.

The code doesn't produce any runtime issues, but makes memory
sanitizers angry:

 Conditional jump or move depends on uninitialised value(s)
    at 0x55C056F: xsk_get_max_queues (xsk.c:336)
    by 0x55C05B2: xsk_create_bpf_maps (xsk.c:354)
    by 0x55C089F: xsk_setup_xdp_prog (xsk.c:447)
    by 0x55C0E57: xsk_socket__create (xsk.c:601)
  Uninitialised value was created by a stack allocation
    at 0x55C04CD: xsk_get_max_queues (xsk.c:318)

Additionally fixed warning on uninitialized bytes in ioctl arguments:

 Syscall param ioctl(SIOCETHTOOL) points to uninitialised byte(s)
    at 0x648D45B: ioctl (in /usr/lib64/libc-2.28.so)
    by 0x55C0546: xsk_get_max_queues (xsk.c:330)
    by 0x55C05B2: xsk_create_bpf_maps (xsk.c:354)
    by 0x55C089F: xsk_setup_xdp_prog (xsk.c:447)
    by 0x55C0E57: xsk_socket__create (xsk.c:601)
  Address 0x1ffefff378 is on thread 1's stack
  in frame #1, created by xsk_get_max_queues (xsk.c:318)
  Uninitialised value was created by a stack allocation
    at 0x55C04CD: xsk_get_max_queues (xsk.c:318)

CC: Magnus Karlsson <magnus.karlsson@intel.com>
Fixes: 1cad0788 ("libbpf: add support for using AF_XDP sockets")
Signed-off-by: Ilya Maximets <i.maximets@samsung.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Eric Dumazet says:

====================
First patch changes the kernel, second patch
adds a new test.

Note that other patches might be needed to take
care of similar issues in sock_ops_convert_ctx_access()
and SOCK_OPS_GET_FIELD()
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Use BPF_REG_1 for source and destination of gso_segs read,
to exercise "bpf: fix access to skb_shared_info->gso_segs" fix.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

It is possible we reach bpf_convert_ctx_access() with
si->dst_reg == si->src_reg

Therefore, we need to load BPF_REG_AX before eventually
mangling si->src_reg.

syzbot generated this x86 code :
   3:   55                      push   %rbp
   4:   48 89 e5                mov    %rsp,%rbp
   7:   48 81 ec 00 00 00 00    sub    $0x0,%rsp // Might be avoided ?
   e:   53                      push   %rbx
   f:   41 55                   push   %r13
  11:   41 56                   push   %r14
  13:   41 57                   push   %r15
  15:   6a 00                   pushq  $0x0
  17:   31 c0                   xor    %eax,%eax
  19:   48 8b bf c0 00 00 00    mov    0xc0(%rdi),%rdi
  20:   44 8b 97 bc 00 00 00    mov    0xbc(%rdi),%r10d
  27:   4c 01 d7                add    %r10,%rdi
  2a:   48 0f b7 7f 06          movzwq 0x6(%rdi),%rdi // Crash
  2f:   5b                      pop    %rbx
  30:   41 5f                   pop    %r15
  32:   41 5e                   pop    %r14
  34:   41 5d                   pop    %r13
  36:   5b                      pop    %rbx
  37:   c9                      leaveq
  38:   c3                      retq

Fixes: d9ff286a ("bpf: allow BPF programs access skb_shared_info->gso_segs field")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Replace the custom implementation with fwnode_get_mac_address,
which works on both DT and ACPI platforms.

While here, replace memcpy() by ether_addr_copy().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The very first check in test_pkt_md_access is failing on s390, which
happens because loading a part of a struct __sk_buff field produces
an incorrect result.

The preprocessed code of the check is:

{
	__u8 tmp = *((volatile __u8 *)&skb->len +
		((sizeof(skb->len) - sizeof(__u8)) / sizeof(__u8)));
	if (tmp != ((*(volatile __u32 *)&skb->len) & 0xFF)) return 2;
};

clang generates the following code for it:

      0:	71 21 00 03 00 00 00 00	r2 = *(u8 *)(r1 + 3)
      1:	61 31 00 00 00 00 00 00	r3 = *(u32 *)(r1 + 0)
      2:	57 30 00 00 00 00 00 ff	r3 &= 255
      3:	5d 23 00 1d 00 00 00 00	if r2 != r3 goto +29 <LBB0_10>

Finally, verifier transforms it to:

  0: (61) r2 = *(u32 *)(r1 +104)
  1: (bc) w2 = w2
  2: (74) w2 >>= 24
  3: (bc) w2 = w2
  4: (54) w2 &= 255
  5: (bc) w2 = w2

The problem is that when verifier emits the code to replace a partial
load of a struct __sk_buff field (*(u8 *)(r1 + 3)) with a full load of
struct sk_buff field (*(u32 *)(r1 + 104)), an optional shift and a
bitwise AND, it assumes that the machine is little endian and
incorrectly decides to use a shift.

Adjust shift count calculation to account for endianness.

Fixes: 31fd8581 ("bpf: permits narrower load from bpf program context fields")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

The onboard sky2 NIC on ASUS P6T WS PRO doesn't work after PM resume
due to the infamous IRQ problem.  Disabling MSI works around it, so
let's add it to the blacklist.

Unfortunately the BIOS on the machine doesn't fill the standard
DMI_SYS_* entry, so we pick up DMI_BOARD_* entries instead.

BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1142496Reported-and-tested-by: Marcus Seyfarth <m.seyfarth@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>