- 15 Apr, 2020 1 commit
-
-
Sebastian Reichel authored
As mentioned slightly out of patch context in the code, there is no reset routine for the chip. On boards where the chip is supplied by a fixed regulator, it might not even be resetted during (e.g. watchdog) reboot and can be in any state. If the device is probed with VAG enabled, the driver's probe routine will generate a loud pop sound when ANA_POWER is being programmed. Avoid this by properly disabling just the VAG bit and waiting the required power down time. Signed-off-by:
Sebastian Reichel <sebastian.reichel@collabora.com> Reviewed-by:
Fabio Estevam <festivem@gmail.com> Link: https://lore.kernel.org/r/20200414181140.145825-1-sebastian.reichel@collabora.comSigned-off-by:
Mark Brown <broonie@kernel.org>
-
- 14 Apr, 2020 16 commits
-
-
Johan Jonker authored
In the old txt situation we add/describe only properties that are used by the driver/hardware itself. With yaml it also filters things in a node that are used by other drivers like 'power-domains' for rk3399, so add it to 'rockchip-i2s.yaml'. Signed-off-by:
Johan Jonker <jbx6244@gmail.com> Reviewed-by:
Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20200324094149.6904-3-jbx6244@gmail.comSigned-off-by:
-
Charles Keepax authored
Signed-off-by:
Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20200409181311.30247-1-ckeepax@opensource.cirrus.comSigned-off-by:
-
Srinivas Kandagatla authored
WSA881x works in PDM mode so the wordlength is fixed, which also makes the only field "WordLength" in DPN_BlockCtrl1 register a read-only. Writing to this register will throw up errors with Qualcomm Controller. So use ro_blockctrl1_reg flag to mark this field as read-only so that core will not write to this register. Signed-off-by:
Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Reviewed-by:
Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20200414110347.23829-1-srinivas.kandagatla@linaro.orgSigned-off-by:
-
Bjorn Andersson authored
All error paths in qcom_snd_parse_of() prints more specific error messages, so silence the one in apq8096_platform_probe() and sdm845_snd_platform_probe() to avoid spamming the kernel log. Signed-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20200406003229.2354631-1-bjorn.andersson@linaro.orgSigned-off-by:
-
Sebastian Fricke authored
Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'. Fixes: 3e086edf("ASoC: stm32: add SAI drivers") Signed-off-by:
Sebastian Fricke <sebastian.fricke.linux@gmail.com> Link: https://lore.kernel.org/r/20200413042952.7675-1-sebastian.fricke.linux@gmail.comSigned-off-by:
-
Charles Keepax authored
This helper is adding very little both it and is one caller are very small functions simply combine the two. Signed-off-by:
-
Charles Keepax authored
Move the error message into snd_soc_dapm_new_dai from dapm_connect_dai_pair, since the two copies are almost identical and are the only callers. Signed-off-by:
-
Johan Jonker authored
In the old txt situation we add/describe only properties that are used by the driver/hardware itself. With yaml it also filters things in a node that are used by other drivers like 'power-domains' for rk3399, so add it to 'rockchip-spdif.yaml'. Signed-off-by:
-
Johan Jonker authored
'#sound-dai-cells' is required to properly interpret the list of DAI specified in the 'sound-dai' property, so add them to 'rockchip-spdif.yaml' Signed-off-by:
-
Johan Jonker authored
Current dts files with 'spdif' nodes are manually verified. In order to automate this process rockchip-spdif.txt has to be converted to yaml. Also rk3188.dtsi, rk3288.dtsi use an extra fallback string, so change this in the documentation. Changed: "rockchip,rk3188-spdif", "rockchip,rk3066-spdif" "rockchip,rk3288-spdif", "rockchip,rk3066-spdif" Signed-off-by:
-
Jason Yan authored
Fix the following gcc warning: sound/soc/intel/common/soc-acpi-intel-cml-match.c:116:45: warning: ‘rt1308_2_adr’ defined but not used [-Wunused-const-variable=] static const struct snd_soc_acpi_adr_device rt1308_2_adr[] = { ^~~~~~~~~~~~ Reported-by:Hulk Robot <hulkci@huawei.com> Signed-off-by:
Jason Yan <yanaijie@huawei.com> Link: https://lore.kernel.org/r/20200410081117.21319-2-yanaijie@huawei.comSigned-off-by:
-
Jason Yan authored
Fix the following gcc warning: sound/soc/intel/common/soc-acpi-intel-icl-match.c:90:45: warning: ‘rt1308_2_adr’ defined but not used [-Wunused-const-variable=] static const struct snd_soc_acpi_adr_device rt1308_2_adr[] = { ^~~~~~~~~~~~ Reported-by:Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20200410081117.21319-1-yanaijie@huawei.comSigned-off-by:
-
Akshu Agrawal authored
RT5682 buttons were incorrectly mapped. Signed-off-by:
Akshu Agrawal <akshu.agrawal@amd.com> Link: https://lore.kernel.org/r/20200414113527.13532-1-akshu.agrawal@amd.comSigned-off-by:
-
Philipp Puschmann authored
If probe fails after enabling the regulators regulator_put is called for each supply without having them disabled before. This produces some warnings like WARNING: CPU: 0 PID: 90 at drivers/regulator/core.c:2044 _regulator_put.part.0+0x154/0x15c [<c010f7a8>] (unwind_backtrace) from [<c010c544>] (show_stack+0x10/0x14) [<c010c544>] (show_stack) from [<c012b640>] (__warn+0xd0/0xf4) [<c012b640>] (__warn) from [<c012b9b4>] (warn_slowpath_fmt+0x64/0xc4) [<c012b9b4>] (warn_slowpath_fmt) from [<c04c4064>] (_regulator_put.part.0+0x154/0x15c) [<c04c4064>] (_regulator_put.part.0) from [<c04c4094>] (regulator_put+0x28/0x38) [<c04c4094>] (regulator_put) from [<c04c40cc>] (regulator_bulk_free+0x28/0x38) [<c04c40cc>] (regulator_bulk_free) from [<c0579b2c>] (release_nodes+0x1d0/0x22c) [<c0579b2c>] (release_nodes) from [<c05756dc>] (really_probe+0x108/0x34c) [<c05756dc>] (really_probe) from [<c0575aec>] (driver_probe_device+0xb8/0x16c) [<c0575aec>] (driver_probe_device) from [<c0575d40>] (device_driver_attach+0x58/0x60) [<c0575d40>] (device_driver_attach) from [<c0575da0>] (__driver_attach+0x58/0xcc) [<c0575da0>] (__driver_attach) from [<c0573978>] (bus_for_each_dev+0x78/0xc0) [<c0573978>] (bus_for_each_dev) from [<c0574b5c>] (bus_add_driver+0x188/0x1e0) [<c0574b5c>] (bus_add_driver) from [<c05768b0>] (driver_register+0x74/0x108) [<c05768b0>] (driver_register) from [<c061ab7c>] (i2c_register_driver+0x3c/0x88) [<c061ab7c>] (i2c_register_driver) from [<c0102df8>] (do_one_initcall+0x58/0x250) [<c0102df8>] (do_one_initcall) from [<c01a91bc>] (do_init_module+0x60/0x244) [<c01a91bc>] (do_init_module) from [<c01ab5a4>] (load_module+0x2180/0x2540) [<c01ab5a4>] (load_module) from [<c01abbd4>] (sys_finit_module+0xd0/0xe8) [<c01abbd4>] (sys_finit_module) from [<c01011e0>] (__sys_trace_return+0x0/0x20) Fixes: 3fd6e7d9 (ASoC: tas571x: New driver for TI TAS571x power amplifiers) Signed-off-by:
Philipp Puschmann <p.puschmann@pironex.de> Link: https://lore.kernel.org/r/20200414112754.3365406-1-p.puschmann@pironex.deSigned-off-by:
-
Charles Keepax authored
Refactoring was done to factor out the linking of DAI widgets into a helper function, dapm_add_valid_dai_widget. However when this was done, a regression was introduced for CODEC to CODEC links. It was over looked that the playback and capture variables persisted across all CODEC DAIs being processed, which ensured that the special DAI widget that is added for CODEC to CODEC links was only created once. This bug causes kernel panics during DAPM shutdown. To stick with the spirit of the original refactoring whilst fixing the issue, variables to hold the DAI widgets are added to snd_soc_dai_link. Furthermore the dapm_add_valid_dai_widget function is renamed to dapm_connect_dai_pair, the function only adds DAI widgets in the CODEC to CODEC case and its primary job is to add routes connecting two DAI widgets, making the original name quite misleading. Fixes: 6c4b13b5 ("ASoC: Add dapm_add_valid_dai_widget helper") Signed-off-by:
-
Krzysztof Kozlowski authored
Commit 450312b6 ("ASoC: soc-core: remove DAI suspend/resume") removed the DAI side suspend/resume hooks and switched entirely to component suspend/resume. However the Samsung SoC s3c-i2s-v2 driver was not updated. Move the suspend/resume hooks from s3c-i2s-v2.c to s3c2412-i2s.c while changing dai to component which allows to keep the struct snd_soc_component_driver const. This fixes build errors: sound/soc/samsung/s3c-i2s-v2.c: In function ‘s3c_i2sv2_register_component’: sound/soc/samsung/s3c-i2s-v2.c:730:9: error: ‘struct snd_soc_dai_driver’ has no member named ‘suspend’ dai_drv->suspend = s3c2412_i2s_suspend; Reported-by:
Arnd Bergmann <arnd@arndb.de> Fixes: 450312b6 ("ASoC: soc-core: remove DAI suspend/resume") Signed-off-by:
Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/20200413124548.28197-1-krzk@kernel.orgSigned-off-by:
-
- 09 Apr, 2020 6 commits
-
-
Amadeusz Sławiński authored
Function soc_tplg_dai_config can fail, check for and handle possible failure. Signed-off-by:
Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com> Reviewed-by:
Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by:
-
Amadeusz Sławiński authored
Function pcm_new_ver can fail, so we should check it's return value and handle possible error. Signed-off-by:
-
Amadeusz Sławiński authored
Function soc_tplg_add_route can propagate error code from callback, we should check its return value and handle fail in correct way. Signed-off-by:
-
Amadeusz Sławiński authored
Functions soc_tplg_denum_create, soc_tplg_dmixer_create, soc_tplg_dbytes_create can fail, so their return values should be checked and error should be propagated. Signed-off-by:
-
Amadeusz Sławiński authored
Function soc_tplg_create_tlv can fail, so we should check if it succeded or not and proceed appropriately. Signed-off-by:
-
Amadeusz Sławiński authored
kstrdup is an allocation function and it can fail, so its return value should be checked and handled appropriately. In order to check all cases, we need to modify set_stream_info to return a value, so check that everything went correctly when doing kstrdup(). Later add proper checks and error handlers. Signed-off-by:
-
- 07 Apr, 2020 1 commit
-
-
Mike Willard authored
Pull the RST line low then high when initializing the driver, in order to force a reset of the chip. Previously, the line was not pulled low, which could result in the chip registers not resetting to their default values on boot. Signed-off-by:
Mike Willard <mwillard@izotope.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200401205454.79792-1-mwillard@izotope.comSigned-off-by:
-
- 06 Apr, 2020 3 commits
-
-
Hans de Goede authored
The Medion E1239T uses the default jack-detect mode 3, but instead of using an analog microphone it is using a DMIC on dmic-data-pin 1, like other models following Intel's Brasswell's reference design. This commit adds a DMI quirk pointing to the intel_braswell_platform_data for this model. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Reviewed-by:
-
Hans de Goede authored
The MPMAN MPWIN895CL tablet almost fully works with out default settings. The only problem is that it has only 1 speaker so any sounds only playing on the right channel get lost. Add a quirk for this model using the default settings + MONO_SPEAKER. Signed-off-by:
-
Julia Lawall authored
The commit 0d6defc7 ("ASoC: stm32: sai: manage rebind issue") converts some function calls to their non-devm equivalents. The appropriate cleanup code was added to the remove function, but not to the probe function. Add a call to snd_dmaengine_pcm_unregister to compensate for the call to snd_dmaengine_pcm_register in case of subsequent failure. Fixes: commit 0d6defc7 ("ASoC: stm32: sai: manage rebind issue") Signed-off-by:
Julia Lawall <Julia.Lawall@inria.fr> Acked-by:
Olivier Moysan <olivier.moysan@st.com> Link: https://lore.kernel.org/r/1586099028-5104-1-git-send-email-Julia.Lawall@inria.frSigned-off-by:
-
- 03 Apr, 2020 4 commits
-
-
Hans de Goede authored
GCC 10 gives a "variable might be used uninitialized" warning for the block variable in sst_prepare_and_post_msg(). This is a false-positive warning, but lets fix it anyways. Signed-off-by:
-
Hans de Goede authored
sst_fill_and_send_cmd_unlocked must be called with the drv->lock mutex locked already. In the past there have been cases where this was not the case, add a WARN_ON to check for drv->lock being locked. Signed-off-by:
-
Hans de Goede authored
sst_send_slot_map() uses sst_fill_and_send_cmd_unlocked() because in some places it is called with the drv->lock mutex already held. So it must always be called with the mutex locked. This commit adds missing locking in the sst_set_be_modules() code-path. Fixes: 24c8d141 ("ASoC: Intel: mrfld: add DSP core controls") Signed-off-by:
-
Hans de Goede authored
Using a Canon Lake machine with the SOF driver causes dmesg to fill up with a ton of these messages: [ 275.902194] sof-audio-pci 0000:00:1f.3: firmware boot complete [ 351.529358] sof-audio-pci 0000:00:1f.3: firmware boot complete [ 560.049047] sof-audio-pci 0000:00:1f.3: firmware boot complete etc. Since the DSP is powered down when not in used this happens everytime e.g. a notification plays, polluting dmesg. Turn this messages into a debug message, matching what the code already does for the ""booting DSP firmware" message. Signed-off-by:
-
- 01 Apr, 2020 3 commits
-
-
이경택 authored
Current topology doesn't add prefix of component to new kcontrol. Signed-off-by:
Gyeongtaek Lee <gt82.lee@samsung.com> Link: https://lore.kernel.org/r/009b01d60804$ae25c2d0$0a714870$@samsung.comSigned-off-by:
-
YueHaibing authored
If I2C is n but SoundWire is m, building fails: sound/soc/codecs/rt5682.c:3716:1: warning: data definition has no type or storage class module_i2c_driver(rt5682_i2c_driver); ^~~~~~~~~~~~~~~~~ sound/soc/codecs/rt5682.c:3716:1: error: type defaults to 'int' in declaration of 'module_i2c_driver' [-Werror=implicit-int] sound/soc/codecs/rt5682.c:3716:1: warning: parameter names (without types) in function declaration Guard this use #ifdef CONFIG_I2C. Fixes: 5549ea64 ("ASoC: rt5682: fix unmet dependencies") Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Link: https://lore.kernel.org/r/20200401091055.34112-1-yuehaibing@huawei.comSigned-off-by:
-
이경택 authored
soc_compr_trigger_fe() allows start or stop after pause_push. In dpcm_be_dai_trigger(), however, only pause_release is allowed command after pause_push. So, start or stop after pause in compress offload is always returned as error if the compress offload is used with dpcm. To fix the problem, SND_SOC_DPCM_STATE_PAUSED should be allowed for start or stop command. Signed-off-by:
-
- 31 Mar, 2020 2 commits
-
-
이경택 authored
Since a virtual mixer has no backing registers to decide which path to connect, it will try to match with initial state. This is to ensure that the default mixer choice will be correctly powered up during initialization. Invert flag is used to select initial state of the virtual switch. Since actual hardware can't be disconnected by virtual switch, connected is better choice as initial state in many cases. Signed-off-by:
-
Stephan Gerhold authored
At the moment, playing audio with PulseAudio with the qdsp6 driver results in distorted sound. It seems like its timer-based scheduling does not work properly with qdsp6 since setting tsched=0 in the PulseAudio configuration avoids the issue. Apparently this happens when the pointer() callback is not accurate enough. There is a SNDRV_PCM_INFO_BATCH flag that can be used to stop PulseAudio from using timer-based scheduling by default. According to https://www.alsa-project.org/pipermail/alsa-devel/2014-March/073816.html: The flag is being used in the sense explained in the previous audio meeting -- the data transfer granularity isn't fine enough but aligned to the period size (or less). q6asm-dai reports the position as multiple of prtd->pcm_count = snd_pcm_lib_period_bytes(substream) so it indeed just a multiple of the period size. Therefore adding the flag here seems appropriate and makes audio work out of the box. Fixes: 2a9e92d3 ("ASoC: qdsp6: q6asm: Add q6asm dai driver") Signed-off-by:
Stephan Gerhold <stephan@gerhold.net> Reviewed-by:
-
- 30 Mar, 2020 4 commits
-
-
Mark Brown authored
Merge series "ASoC: Intel: boards: Remove ignore_suspend flag from SSP0 dai link" from Cezary Rojewski <cezary.rojewski@intel.com>: As of commit: ASoC: soc-core: care .ignore_suspend for Component suspend function soc-core::snd_soc_suspend no longer ignores 'ignore_suspend' flag for dai links. While BE dai link for System Pin is supposed to follow standard suspend-resume flow, appended 'ignore_suspend' flag disturbs that flow and causes audio to break right after resume. Remove the flag to address this. Link to first message in conversation: https://lkml.org/lkml/2020/3/18/54 Cezary Rojewski (4): ASoC: Intel: broadwell: Remove ignore_suspend flag from SSP0 dai link ASoC: Intel: haswell: Remove ignore_suspend flag from SSP0 dai link ASoC: Intel: bdw-rt5677: Remove ignore_suspend flag from SSP0 dai link ASoC: Intel: bdw-rt5650: Remove ignore_suspend flag from SSP0 dai link sound/soc/intel/boards/bdw-rt5650.c | 1 - sound/soc/intel/boards/bdw-rt5677.c | 1 - sound/soc/intel/boards/broadwell.c | 1 - sound/soc/intel/boards/haswell.c | 1 - 4 files changed, 4 deletions(-) -- 2.17.1
-
Pierre-Louis Bossart authored
The addition of a single flag to track the DAI status prevents the DAI startup sequence from being called on capture if the DAI is already used for playback. Fix by extending the existing code with one flag per direction. Fixes: b56be800 ("ASoC: soc-pcm: call snd_soc_dai_startup()/shutdown() once") Reported-by:
-
이경택 authored
If regwshift is 32 and the selected architecture compiles '<<' operator for signed int literal into rotating shift, '1<<regwshift' became 1 and it makes regwmask to 0x0. The literal is set to unsigned long to get intended regwmask. Signed-off-by:
-
Cezary Rojewski authored
As of commit: ASoC: soc-core: care .ignore_suspend for Component suspend function soc-core::snd_soc_suspend no longer ignores 'ignore_suspend' flag for dai links. While BE dai link for System Pin is supposed to follow standard suspend-resume flow, appended 'ignore_suspend' flag disturbs that flow and causes audio to break right after resume. Remove the flag to address this. Signed-off-by:
Cezary Rojewski <cezary.rojewski@intel.com> Acked-by:
-
