- 15 Dec, 2015 13 commits
-
-
Daniel Borkmann authored
[ Upstream commit c72219b7 ] In case no struct sockaddr_ll has been passed to packet socket's sendmsg() when doing a TX_RING flush run, then skb->protocol is set to po->num instead, which is the protocol passed via socket(2)/bind(2). Applications only xmitting can go the path of allocating the socket as socket(PF_PACKET, <mode>, 0) and do a bind(2) on the TX_RING with sll_protocol of 0. That way, register_prot_hook() is neither called on creation nor on bind time, which saves cycles when there's no interest in capturing anyway. That leaves us however with po->num 0 instead and therefore the TX_RING flush run sets skb->protocol to 0 as well. Eric reported that this leads to problems when using tools like trafgen over bonding device. I.e. the bonding's hash function could invoke the kernel's flow dissector, which depends on skb->protocol being properly set. In the current situation, all the traffic is then directed to a single slave. Fix it up by inferring skb->protocol from the Ethernet header when not set and we have ARPHRD_ETHER device type. This is only done in case of SOCK_RAW and where we have a dev->hard_header_len length. In case of ARPHRD_ETHER devices, this is guaranteed to cover ETH_HLEN, and therefore being accessed on the skb after the skb_store_bits(). Reported-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Daniel Borkmann authored
[ Upstream commit 3c70c132 ] Packet sockets can be used by various net devices and are not really restricted to ARPHRD_ETHER device types. However, when currently checking for the extra 4 bytes that can be transmitted in VLAN case, our assumption is that we generally probe on ARPHRD_ETHER devices. Therefore, before looking into Ethernet header, check the device type first. This also fixes the issue where non-ARPHRD_ETHER devices could have no dev->hard_header_len in TX_RING SOCK_RAW case, and thus the check would test unfilled linear part of the skb (instead of non-linear). Fixes: 57f89bfa ("network: Allow af_packet to transmit +4 bytes for VLAN packets.") Fixes: 52f1454f ("packet: allow to transmit +4 byte in TX_RING slot for VLAN case") Signed-off-by:
-
Daniel Borkmann authored
[ Upstream commit 8fd6c80d ] We concluded that the skb_probe_transport_header() should better be called unconditionally. Avoiding the call into the flow dissector has also not really much to do with the direct xmit mode. While it seems that only virtio_net code makes use of GSO from non RX/TX ring packet socket paths, we should probe for a transport header nevertheless before they hit devices. Reference: http://thread.gmane.org/gmane.linux.network/386173/Signed-off-by:
Jason Wang <jasowang@redhat.com> Signed-off-by:
-
Daniel Borkmann authored
[ Upstream commit efdfa2f7 ] In tpacket_fill_skb() commit c1aad275 ("packet: set transport header before doing xmit") and later on 40893fd0 ("net: switch to use skb_probe_transport_header()") was probing for a transport header on the skb from a ring buffer slot, but at a time, where the skb has _not even_ been filled with data yet. So that call into the flow dissector is pretty useless. Lets do it after we've set up the skb frags. Fixes: c1aad275 ("packet: set transport header before doing xmit") Reported-by:
-
Kamal Mostafa authored
[ Upstream commit d7475de5 ] Use the local uapi headers to keep in sync with "recently" added #define's (e.g. SKF_AD_VLAN_TPID). Refactored CFLAGS, and bpf_asm doesn't need -I. Fixes: 3f356385 ("filter: bpf_asm: add minimal bpf asm tool") Signed-off-by:
Kamal Mostafa <kamal@canonical.com> Acked-by:
-
Martin KaFai Lau authored
[ Upstrem commit 02bcf4e0 ] All DST_NOCACHE rt6_info used to have rt->dst.from set to its parent. After commit 8e3d5be7 ("ipv6: Avoid double dst_free"), DST_NOCACHE is also set to rt6_info which does not have a parent (i.e. rt->dst.from is NULL). This patch catches the rt->dst.from == NULL case. Fixes: 8e3d5be7 ("ipv6: Avoid double dst_free") Signed-off-by:
Martin KaFai Lau <kafai@fb.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Martin KaFai Lau authored
[ Upstream commit 5973fb1e ] Since the expires of the DST_NOCACHE rt can be set during the ip6_rt_update_pmtu(), we also need to consider the expires value when doing ip6_dst_check(). This patches creates __rt6_check_expired() to only check the expire value (if one exists) of the current rt. In rt6_dst_from_check(), it adds __rt6_check_expired() as one of the condition check. Signed-off-by:
-
Martin KaFai Lau authored
[ Upstream commit 0d3f6d29 ] The original bug report: https://bugzilla.redhat.com/show_bug.cgi?id=1272571 The setup has a IPv4 GRE tunnel running in a IPSec. The bug happens when ndisc starts sending router solicitation at the gre interface. The simplified oops stack is like: __lock_acquire+0x1b2/0x1c30 lock_acquire+0xb9/0x140 _raw_write_lock_bh+0x3f/0x50 __ip6_ins_rt+0x2e/0x60 ip6_ins_rt+0x49/0x50 ~~~~~~~~ __ip6_rt_update_pmtu.part.54+0x145/0x250 ip6_rt_update_pmtu+0x2e/0x40 ~~~~~~~~ ip_tunnel_xmit+0x1f1/0xf40 __gre_xmit+0x7a/0x90 ipgre_xmit+0x15a/0x220 dev_hard_start_xmit+0x2bd/0x480 __dev_queue_xmit+0x696/0x730 dev_queue_xmit+0x10/0x20 neigh_direct_output+0x11/0x20 ip6_finish_output2+0x21f/0x770 ip6_finish_output+0xa7/0x1d0 ip6_output+0x56/0x190 ~~~~~~~~ ndisc_send_skb+0x1d9/0x400 ndisc_send_rs+0x88/0xc0 ~~~~~~~~ The rt passed to ip6_rt_update_pmtu() is created by icmp6_dst_alloc() and it is not managed by the fib6 tree, so its rt6i_table == NULL. When __ip6_rt_update_pmtu() creates a RTF_CACHE clone, the newly created clone also has rt6i_table == NULL and it causes the ip6_ins_rt() oops. During pmtu update, we only want to create a RTF_CACHE clone from a rt which is currently managed (or owned) by the fib6 tree. It means either rt->rt6i_node != NULL or rt is a RTF_PCPU clone. It is worth to note that rt6i_table may not be NULL even it is not (yet) managed by the fib6 tree (e.g. addrconf_dst_alloc()). Hence, rt6i_node is a better check instead of rt6i_table. Fixes: 45e4fd26 ("ipv6: Only create RTF_CACHE routes after encountering pmtu") Signed-off-by:
Chris Siebenmann <cks-rhbugzilla@cs.toronto.edu> Cc: Chris Siebenmann <cks-rhbugzilla@cs.toronto.edu> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit 9490f886 ] sendpage did not care about credentials at all. This could lead to situations in which because of fd passing between processes we could append data to skbs with different scm data. It is illegal to splice those skbs together. Instead we have to allocate a new skb and if requested fill out the scm details. Fixes: 869e7c62 ("net: af_unix: implement stream sendpage support") Reported-by:
Al Viro <viro@zeniv.linux.org.uk> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Eric Dumazet <edumazet@google.com> Signed-off-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Rainer Weikusat authored
[ Upstream commit 7d267278 ] Rainer Weikusat <rweikusat@mobileactivedefense.com> writes: An AF_UNIX datagram socket being the client in an n:1 association with some server socket is only allowed to send messages to the server if the receive queue of this socket contains at most sk_max_ack_backlog datagrams. This implies that prospective writers might be forced to go to sleep despite none of the message presently enqueued on the server receive queue were sent by them. In order to ensure that these will be woken up once space becomes again available, the present unix_dgram_poll routine does a second sock_poll_wait call with the peer_wait wait queue of the server socket as queue argument (unix_dgram_recvmsg does a wake up on this queue after a datagram was received). This is inherently problematic because the server socket is only guaranteed to remain alive for as long as the client still holds a reference to it. In case the connection is dissolved via connect or by the dead peer detection logic in unix_dgram_sendmsg, the server socket may be freed despite "the polling mechanism" (in particular, epoll) still has a pointer to the corresponding peer_wait queue. There's no way to forcibly deregister a wait queue with epoll. Based on an idea by Jason Baron, the patch below changes the code such that a wait_queue_t belonging to the client socket is enqueued on the peer_wait queue of the server whenever the peer receive queue full condition is detected by either a sendmsg or a poll. A wake up on the peer queue is then relayed to the ordinary wait queue of the client socket via wake function. The connection to the peer wait queue is again dissolved if either a wake up is about to be relayed or the client socket reconnects or a dead peer is detected or the client socket is itself closed. This enables removing the second sock_poll_wait from unix_dgram_poll, thus avoiding the use-after-free, while still ensuring that no blocked writer sleeps forever. Signed-off-by:
Rainer Weikusat <rweikusat@mobileactivedefense.com> Fixes: ec0d215f ("af_unix: fix 'poll for write'/connected DGRAM sockets") Reviewed-by:
Jason Baron <jbaron@akamai.com> Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit a3a116e0 ] While possibly in future we don't necessarily need to use sk_buff_head.lock this is a rather larger change, as it affects the af_unix fd garbage collector, diag and socket cleanups. This is too much for a stable patch. For the time being grab sk_buff_head.lock without disabling bh and irqs, so don't use locked skb_queue_tail. Fixes: 869e7c62 ("net: af_unix: implement stream sendpage support") Cc: Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit 8844f972 ] In case multiple writes to a unix stream socket race we could end up in a situation where we pre-allocate a new skb for use in unix_stream_sendpage but have to free it again in the locked section because another skb has been appended meanwhile, which we must use. Accidentally we didn't clear the pointer after consuming it and so we touched freed memory while appending it to the sk_receive_queue. So, clear the pointer after consuming the skb. This bug has been found with syzkaller (http://github.com/google/syzkaller) by Dmitry Vyukov. Fixes: 869e7c62 ("net: af_unix: implement stream sendpage support") Reported-by:
Dmitry Vyukov <dvyukov@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit 73ed5d25 ] During splicing an af-unix socket to a pipe we have to drop all af-unix socket locks. While doing so we allow another reader to enter unix_stream_read_generic which can read, copy and finally free another skb. If exactly this skb is just in process of being spliced we get a use-after-free report by kasan. First, we must make sure to not have a free while the skb is used during the splice operation. We simply increment its use counter before unlocking the reader lock. Stream sockets have the nice characteristic that we don't care about zero length writes and they never reach the peer socket's queue. That said, we can take the UNIXCB.consumed field as the indicator if the skb was already freed from the socket's receive queue. If the skb was fully consumed after we locked the reader side again we know it has been dropped by a second reader. We indicate a short read to user space and abort the current splice operation. This bug has been found with syzkaller (http://github.com/google/syzkaller) by Dmitry Vyukov. Fixes: 2b514574 ("net: af_unix: implement splice for stream af_unix sockets") Reported-by:
-
- 09 Dec, 2015 27 commits
-
-
Greg Kroah-Hartman authored
-
Sudip Mukherjee authored
commit 3a48d13d upstream. When building with allmodconfig the build was failing with the error: arch/tile/kernel/usb.c:70:1: warning: data definition has no type or storage class [enabled by default] arch/tile/kernel/usb.c:70:1: error: type defaults to 'int' in declaration of 'arch_initcall' [-Werror=implicit-int] arch/tile/kernel/usb.c:70:1: warning: parameter names (without types) in function declaration [enabled by default] arch/tile/kernel/usb.c:63:19: warning: 'tilegx_usb_init' defined but not used [-Wunused-function] Include linux/module.h to resolve the build failure. Signed-off-by:
Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by:
Chris Metcalf <cmetcalf@ezchip.com> Signed-off-by:
-
David Hildenbrand authored
commit 5967c17b upstream. We should never allow to enable/disable any facilities for the guest when other VCPUs were already created. kvm_arch_vcpu_(load|put) relies on SIMD not changing during runtime. If somebody would create and run VCPUs and then decides to enable SIMD, undefined behaviour could be possible (e.g. vector save area not being set up). Acked-by:
Christian Borntraeger <borntraeger@de.ibm.com> Acked-by:
Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by:
David Hildenbrand <dahi@linux.vnet.ibm.com> Signed-off-by:
-
Boris Ostrovsky authored
commit b4ff8389 upstream. After commit 8c058b0b ("x86/irq: Probe for PIC presence before allocating descs for legacy IRQs") early_irq_init() will no longer preallocate descriptors for legacy interrupts if PIC does not exist, which is the case for Xen PV guests. Therefore we may need to allocate those descriptors ourselves. Signed-off-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Suggested-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Cc: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by:
-
Arnd Bergmann authored
commit 9f088dba upstream. The recently introduced lnet_peer_set_alive() function uses get_seconds() to read the current time into a shared variable, but all other uses of that variable compare it to jiffies values. This changes the current use to jiffies as well for consistency. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Fixes: af3fa7c7 ("staging/lustre/lnet: peer aliveness status and NI status") Cc: Liang Zhen <liang.zhen@intel.com> Cc: James Simmons <uja.ornl@gmail.com> Cc: Isaac Huang <he.huang@intel.com> Signed-off-by:
Oleg Drokin <oleg.drokin@intel.com> Signed-off-by:
-
Rajmohan Mani authored
commit a5964396 upstream. Existing Intel xHCI controllers require a delay of 1 mS, after setting the CMD_RESET bit in command register, before accessing any HC registers. This allows the HC to complete the reset operation and be ready for HC register access. Without this delay, the subsequent HC register access, may result in a system hang, very rarely. Verified CherryView / Braswell platforms go through over 5000 warm reboot cycles (which was not possible without this patch), without any xHCI reset hang. Signed-off-by:
Rajmohan Mani <rajmohan.mani@intel.com> Tested-by:
Joe Lawrence <joe.lawrence@stratus.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Peter Hurley authored
commit ee0c1a65 upstream. The correct lock order is atomic_write_lock => termios_rwsem, as established by tty_write() => n_tty_write(). Fixes: c274f6ef ("tty: Hold termios_rwsem for tcflow(TCIxxx)") Reported-and-Tested-by:
Peter Hurley <peter@hurleysoftware.com> Signed-off-by:
-
Peter Hurley authored
commit 6b2a3d62 upstream. The data to audit/record is in the 'from' buffer (ie., the input read buffer). Fixes: 72586c60 ("n_tty: Fix auditing support for cannonical mode") Cc: Miloslav Trmač <mitr@redhat.com> Signed-off-by:
Laura Abbott <labbott@fedoraproject.org> Signed-off-by:
-
James Hogan authored
commit 3e8137a1 upstream. Commit 0fd972a7 (module: relocate module_init from init.h to module.h) broke the build of ttyFDC driver due to that driver's (mis)use of module_mips_cdmm_driver() without first including module.h, for example: In file included from ./arch/mips/include/asm/cdmm.h +11 :0, from drivers/tty/mips_ejtag_fdc.c +34 : include/linux/device.h +1295 :1: warning: data definition has no type or storage class ./arch/mips/include/asm/cdmm.h +84 :2: note: in expansion of macro ‘module_driver’ drivers/tty/mips_ejtag_fdc.c +1157 :1: note: in expansion of macro ‘module_mips_cdmm_driver’ include/linux/device.h +1295 :1: error: type defaults to ‘int’ in declaration of ‘module_init’ [-Werror=implicit-int] ./arch/mips/include/asm/cdmm.h +84 :2: note: in expansion of macro ‘module_driver’ drivers/tty/mips_ejtag_fdc.c +1157 :1: note: in expansion of macro ‘module_mips_cdmm_driver’ drivers/tty/mips_ejtag_fdc.c +1157 :1: warning: parameter names (without types) in function declaration Instead of just adding the module.h include, switch to using the new builtin_mips_cdmm_driver() helper macro and drop the remove callback, since it isn't needed. If module support is added later, the code can always be resurrected. Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: linux-mips@linux-mips.org Signed-off-by:
-
Clemens Ladisch authored
commit a91e627e upstream. One of the many faults of the QinHeng CH345 USB MIDI interface chip is that it does not handle received SysEx messages correctly -- every second event packet has a wrong code index number, which is the one from the last seen message, instead of 4. For example, the two messages "FE F0 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E F7" result in the following event packets: correct: CH345: 0F FE 00 00 0F FE 00 00 04 F0 01 02 04 F0 01 02 04 03 04 05 0F 03 04 05 04 06 07 08 04 06 07 08 04 09 0A 0B 0F 09 0A 0B 04 0C 0D 0E 04 0C 0D 0E 05 F7 00 00 05 F7 00 00 A class-compliant driver must interpret an event packet with CIN 15 as having a single data byte, so the other two bytes would be ignored. The message received by the host would then be missing two bytes out of six; in this example, "F0 01 02 03 06 07 08 09 0C 0D 0E F7". These corrupted SysEx event packages contain only data bytes, while the CH345 uses event packets with a correct CIN value only for messages with a status byte, so it is possible to distinguish between these two cases by checking for the presence of this status byte. (Other bugs in the CH345's input handling, such as the corruption resulting from running status, cannot be worked around.) Signed-off-by:
Clemens Ladisch <clemens@ladisch.de> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Clemens Ladisch authored
commit 1ca8b201 upstream. The CH345 USB MIDI chip has two output ports. However, they are multiplexed through one pin, and the number of ports cannot be reduced even for hardware that implements only one connector, so for those devices, data sent to either port ends up on the same hardware output. This becomes a problem when both ports are used at the same time, as longer MIDI commands (such as SysEx messages) are likely to be interrupted by messages from the other port, and thus to get lost. It would not be possible for the driver to detect how many ports the device actually has, except that in practice, _all_ devices built with the CH345 have only one port. So we can just ignore the device's descriptors, and hardcode one output port. Signed-off-by:
-
Clemens Ladisch authored
commit 98d362be upstream. Signed-off-by:
-
Bjørn Mork authored
commit 638148e2 upstream. Thomas reports " 4gsystems sells two total different LTE-surfsticks under the same name. .. The newer version of XS Stick W100 is from "omega" .. Under windows the driver switches to the same ID, and uses MI03\6 for network and MI01\6 for modem. .. echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1c9e ProdID=9b01 Rev=02.32 S: Manufacturer=USB Modem S: Product=USB Modem S: SerialNumber= C: #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage Now all important things are there: wwp0s29f7u2i3 (net), ttyUSB2 (at), cdc-wdm0 (qmi), ttyUSB1 (at) There is also ttyUSB0, but it is not usable, at least not for at. The device works well with qmi and ModemManager-NetworkManager. " Reported-by:
Thomas Schäfer <tschaefer@t-online.de> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Aleksander Morgado authored
commit e07af133 upstream. Also known as Verizon U620L. The device is modeswitched from 1410:9020 to 1410:9022 by selecting the 4th USB configuration: $ sudo usb_modeswitch –v 0x1410 –p 0x9020 –u 4 This configuration provides a ECM interface as well as TTYs ('Enterprise Mode' according to the U620 Linux integration guide). Signed-off-by:
Aleksander Morgado <aleksander@aleksander.es> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
David Woodhouse authored
commit 1bcb49e6 upstream. The Honeywell HGI80 is a wireless interface to the evohome connected thermostat. It uses a TI 3410 USB-serial port. Signed-off-by:
David Woodhouse <David.Woodhouse@intel.com> Signed-off-by:
-
Uwe Kleine-König authored
commit 705e63d2 upstream. There is a bit of a mess in the order of arguments to the ulpi write callback. There is int ulpi_write(struct ulpi *ulpi, u8 addr, u8 val) in drivers/usb/common/ulpi.c; struct usb_phy_io_ops { ... int (*write)(struct usb_phy *x, u32 val, u32 reg); } in include/linux/usb/phy.h. The callback registered by the musb driver has to comply to the latter, but up to now had "offset" first which effectively made the function broken for correct users. So flip the order and while at it also switch to the parameter names of struct usb_phy_io_ops's write. Fixes: ffb865b1 ("usb: musb: add ulpi access operations") Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Bjørn Mork authored
commit 59536da3 upstream. The DEVICE_HWI type was added under the faulty assumption that Huawei devices based on Qualcomm chipsets and firmware use the static USB interface numbering known from Gobi devices. But this model does not apply to Huawei devices like the HP branded lt4112 (Huawei me906e). Huawei firmwares will dynamically assign interface numbers. Functions are renumbered when the firmware is reconfigured. Fix by changing the DEVICE_HWI type to use a simplified version of Huawei's subclass + protocol scheme: Blacklisting known network interface combinations and assuming the rest are serial. Reported-and-tested-by:
Muri Nicanor <muri+libqmi@immerda.ch> Tested-by:
Martin Hauke <mardnh@gmx.de> Fixes: e7181d00 ("USB: qcserial: Add support for HP lt4112 LTE/HSPA+ Gobi 4G Modem") Signed-off-by:
-
Petr Štetiar authored
commit 9d5b5ed7 upstream. It seems like this device has same vendor and product IDs as G2K devices, but it has different number of interfaces(4 vs 5) and also different interface layout which makes it currently unusable: usbcore: registered new interface driver qcserial usbserial: USB Serial support registered for Qualcomm USB modem usb 2-1.2: unknown number of interfaces: 5 lsusb output: Bus 002 Device 003: ID 05c6:9215 Qualcomm, Inc. Acer Gobi 2000 Wireless Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x05c6 Qualcomm, Inc. idProduct 0x9215 Acer Gobi 2000 Wireless Modem bcdDevice 2.32 iManufacturer 1 Quectel iProduct 2 Quectel LTE Module iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 209 bNumInterfaces 5 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xa0 (Bus Powered) Remote Wakeup MaxPower 500mA Signed-off-by:
Petr Štetiar <ynezz@true.cz> [johan: rename define and add comment ] Signed-off-by:
-
Jiri Slaby authored
commit 19cd80a2 upstream. It is not permitted to set task state before lock. usblp_wwait sets the state to TASK_INTERRUPTIBLE and calls mutex_lock_interruptible. Upon return from that function, the state will be TASK_RUNNING again. This is clearly a bug and a warning is generated with LOCKDEP too: WARNING: CPU: 1 PID: 5109 at kernel/sched/core.c:7404 __might_sleep+0x7d/0x90() do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffffa0c588d0>] usblp_wwait+0xa0/0x310 [usblp] Modules linked in: ... CPU: 1 PID: 5109 Comm: captmon Tainted: G W 4.2.5-0.gef2823b-default #1 Hardware name: LENOVO 23252SG/23252SG, BIOS G2ET33WW (1.13 ) 07/24/2012 ffffffff81a4edce ffff880236ec7ba8 ffffffff81716651 0000000000000000 ffff880236ec7bf8 ffff880236ec7be8 ffffffff8106e146 0000000000000282 ffffffff81a50119 000000000000028b 0000000000000000 ffff8802dab7c508 Call Trace: ... [<ffffffff8106e1c6>] warn_slowpath_fmt+0x46/0x50 [<ffffffff8109a8bd>] __might_sleep+0x7d/0x90 [<ffffffff8171b20f>] mutex_lock_interruptible_nested+0x2f/0x4b0 [<ffffffffa0c588fc>] usblp_wwait+0xcc/0x310 [usblp] [<ffffffffa0c58bb2>] usblp_write+0x72/0x350 [usblp] [<ffffffff8121ed98>] __vfs_write+0x28/0xf0 ... Commit 7f477358 (usblp: Implement the ENOSPC convention) moved the set prior locking. So move it back after the lock. Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Fixes: 7f477358 ("usblp: Implement the ENOSPC convention") Acked-By:
Pete Zaitcev <zaitcev@yahoo.com> Signed-off-by:
-
Jonas Gorski authored
commit db1319e1 upstream. Commit d445913c ("usb: ehci-orion: add optional PHY support") added support for optional phys, but devm_phy_optional_get returns -ENOSYS if GENERIC_PHY is not enabled. This causes probe failures, even when there are no phys specified: [ 1.443365] orion-ehci f1058000.usb: init f1058000.usb fail, -38 [ 1.449403] orion-ehci: probe of f1058000.usb failed with error -38 Similar to dwc3, treat -ENOSYS as no phy. Fixes: d445913c ("usb: ehci-orion: add optional PHY support") Signed-off-by:
Jonas Gorski <jogo@openwrt.org> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Jurgen Kramer authored
commit 16771c7c upstream. This patch adds native DSD support for the Aune X1S 32BIT/384 DSD DAC Signed-off-by:
Jurgen Kramer <gtmkramer@xs4all.nl> Signed-off-by:
-
Peter Chen authored
commit ae3e57ae upstream. Some i.mx platforms need three clocks to let controller work, but others only need one, refine clock operation to adapt for all platforms, it fixes a regression found at i.mx27. Signed-off-by:
Peter Chen <peter.chen@freescale.com> Tested-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
-
John Youn authored
commit 94218ee3 upstream. Certain Synopsys prototyping PHY boards are not able to meet timings constraints for LPM. This allows the PHY to meet those timings by leaving the PHY clock running during suspend. Signed-off-by:
John Youn <johnyoun@synopsys.com> Signed-off-by:
-
John Youn authored
commit ec791d14 upstream. Add a quirk to clear the GUSB2PHYCFG.ENBLSLPM bit, which controls whether the PHY receives the suspend signal from the controller. Signed-off-by:
-
John Youn authored
commit bb7f3d6d upstream. Add platform data and set usb3_lpm_capable and has_lpm_erratum. Signed-off-by:
-
John Youn authored
commit 690fb371 upstream. This patch allows the dwc3 driver to run on the new Synopsys USB 3.1 IP core, albeit in USB 3.0 mode only. The Synopsys USB 3.1 IP (DWC_usb31) retains mostly the same register interface and programming model as the existing USB 3.0 controller IP (DWC_usb3). However the GSNPSID and version numbers are different. Add checking for the new ID to pass driver probe. Also, since the DWC_usb31 version number is lower in value than the full GSNPSID of the DWC_usb3 IP, we set the high bit to identify DWC_usb31 and to ensure the values are higher. Finally, add a documentation note about the revision numbering scheme. Any future revision checks (for STARS, workarounds, and new features) should take into consideration how it applies to both the 3.1/3.0 IP. Signed-off-by:
-
John Youn authored
commit e8095a25 upstream. This adds the PCI product ID for the Synopsys USB 3.1 IP core (DWC_usb31) on a HAPS-based PCI development platform. Signed-off-by:
-
