* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  netxen: include ipv6.h (fixes build failure)
  netxen: avoid invalid iounmap

Fixes a build error in absence of CONFIG_IPV6:

drivers/net/netxen/netxen_nic_main.c:1189: error: implicit declaration of function 'ipv6_hdr'
drivers/net/netxen/netxen_nic_main.c:1189: error: invalid type argument of '->'
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For NX3031 only one I/O range is mapped, so unmapping other
two which are used by older chips, causes this warning on
ppc64.

"Attempt to iounmap early bolted mapping at 0x0000000000000000"
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: fix ioctl arg size (userland incompatible change!)
  Btrfs: Clear the device->running_pending flag before bailing on congestion

The structure used to send device in btrfs ioctl calls was not
properly aligned, and so 32 bit ioctls would not work properly on
64 bit kernels.

We could fix this with compat ioctls, but we're just one byte away
and it doesn't make sense at this stage to carry about the compat ioctls
forever at this stage in the project.

This patch brings the ioctl arg up to an evenly aligned 4k.
Signed-off-by: Chris Mason <chris.mason@oracle.com>

Btrfs maintains a queue of async bio submissions so the checksumming
threads don't have to wait on get_request_wait.  In order to avoid
extra wakeups, this code has a running_pending flag that is used
to tell new submissions they don't need to wake the thread.

When the threads notice congestion on a single device, they
may decide to requeue the job and move on to other devices.  This
makes sure the running_pending flag is cleared before the
job is requeued.

It should help avoid IO stalls by making sure the task is woken up
when new submissions come in.
Signed-off-by: Chris Mason <chris.mason@oracle.com>

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  serial: Add 16850 uart type support to OF uart driver
  hvc_console: Remove tty->low_latency
  powerpc: Get the number of SLBs from "slb-size" property
  powerpc: is_hugepage_only_range() must account for both 4kB and 64kB slices
  powerpc/ps3: printing fixups for l64 to ll64 conversion drivers/video
  powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/scsi
  powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/ps3
  powerpc/ps3: Printing fixups for l64 to ll64 conversion sound/ppc
  powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/char
  powerpc/ps3: Printing fixups for l64 to ll64 conversion drivers/block
  powerpc/ps3: Printing fixups for l64 to ll64 conversion arch/powerpc
  powerpc/ps3: ps3_repository_read_mm_info() takes u64 * arguments
  powerpc/ps3: clear_bit()/set_bit() operate on unsigned longs
  powerpc/ps3: The lv1_ routines have u64 parameters
  powerpc/ps3: Use dma_addr_t down through the stack
  powerpc/ps3: set_dabr() takes an unsigned long
  powerpc: Cleanup from l64 to ll64 change drivers/scsi

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  sata_fsl: Return non-zero on error in probe()
  drivers/ata/pata_ali.c: s/isa_bridge/ali_isa_bridge/ to fix alpha build
  libata: New driver for OCTEON SOC Compact Flash interface (v7).
  libata: Add another column to the ata_timing table.
  sata_via: Add VT8261 support
  pata_atiixp: update port enabledness test handling
  [libata] get-identity ioctl: Fix use of invalid memory pointer

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] Skip deleted devices in __scsi_device_lookup_by_target()
  [SCSI] Add SUN Universal Xport to no attach blacklist
  [SCSI] iscsi_tcp: make padbuf non-static
  [SCSI] mpt fusion: Add Firmware debug support
  [SCSI] mpt fusion: Add separate msi enable disable for FC,SPI,SAS
  [SCSI] mpt fusion: Update MPI Headers to version 01.05.19
  [SCSI] qla2xxx: Fix ISP restart bug in multiq code

* 'drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/i915: lock correct mutex around object unreference.
  drm/i915: add support for physical memory objects
  drm/i915: make LVDS fixed mode a preferred mode
  drm: handle depth & bpp changes correctly
  drm: initial KMS config fixes
  drm/i915: setup sarea properly in master_priv
  drm/i915: set vblank enabled flag correctly across IRQ install/uninstall
  drm/i915: don't enable vblanks on disabled pipes

This reverts commit 98e6e286, as Yinghai
Lu reports that it breaks kexec with at least the e1000 and e1000e
drivers.  The reason is that the shutdown sequence puts the hardware
into D3 sleep, and the commit causes us to claim that it then is in D0
(running) state just because we don't understand the PM capabilities.

Which then later makes "pci_set_power_state()" not do anything, and the
device never wakes up properly and just returns 0xff to everything.
Reported-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: From: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

while I was looking over kernel sources I've found this small bug.

Formerly, zero was returned even if an error happened.
Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

drivers/ata/pata_ali.c:44: error: static declaration of 'isa_bridge' follows non-static declaration
arch/alpha/include/asm/pci.h:274: error: previous declaration of 'isa_bridge' was here

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Cavium OCTEON processor support was recently merged, so now we have
this CF driver for your consideration.

Most OCTEON variants have *no* DMA or interrupt support on the CF
interface so for these, only PIO is supported.  Although if DMA is
available, we do take advantage of it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The forthcoming OCTEON SOC Compact Flash driver needs an additional
timing value that was not available in the ata_timing table.  I add a
new column for dmack_hold time.  The values were obtained from the
Compact Flash specification Rev 4.1.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Port enabledness test fits much better into init_one() instead of
pre_reset().  The reason why these tests are in pre_reset() is purely
historical at this point.  Move it to init_one().  This will help
further changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

for SAS drivers.

Caught by Ke Wei (and team?) at Marvell.

Also, move the ata_scsi_ioctl export to libata-scsi.c, as that seems to be the
general trend.
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

This makes sure the mutex is held around the unreference.
Signed-off-by: Dave Airlie <airlied@redhat.com>

This is an initial patch to do support for objects which needs physical
contiguous main ram, cursors and overlay registers on older chipsets.

These objects are bound on cursor bin, like pinning, and we copy
the data to/from the backing store object into the real one on attach/detach.

notes:
possible over the top in attach/detach operations.
no overlay support yet.
Signed-off-by: Dave Airlie <airlied@redhat.com>

The detected fixed panel mode really is preferred, so mark it as such and
add it to the LVDS connector mode list.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>

When mode setting is first initialized, the driver will call into
drm_helper_initial_config() to set up an initial output and framebuffer
configuration.  This routine is responsible for probing the available
connectors, encoders, and crtcs, looking for modes and putting together
something reasonable (where reasonable is defined as "allows kernel
messages to be visible on as many displays as possible").

However, the code was a bit too aggressive in setting default modes when
none were found on a given connector.  Even if some connectors had modes,
any connectors found lacking modes would have the default 800x600 mode added
to their mode list, which in some cases could cause problems later down the
line.  In my case, the LVDS was perfectly available, but the initial config
code added 800x600 modes to both of the detected but unavailable HDMI
connectors (which are on my non-existent docking station).  This ended up
preventing later code from setting a mode on my LVDS, which is bad.

This patch fixes that behavior by making the initial config code walk
through the connectors first, counting the available modes, before it decides
to add any default modes to a possibly connected output.  It also fixes the
logic in drm_target_preferred() that was causing zeroed out modes to be set
as the preferred mode for a given connector, even if no modes were available.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>

This patch adds support for "ns16850" as supported value
of the compatible node in flat device tree uart descriptions.

This is needed for example when you have a XR16C2850 uart
connected to a PPC405's external bus controller.
Signed-off-by: Matthias Fuchs <mfuchs@ma-fu.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This patch removes the tty->low_latency setting.

For irq based hvc_console backends the tty->low_latency must be set to 0,
because the tty_flip_buffer_push() function must not be called from IRQ context
(see drivers/char/tty_buffer.c).

For polled backends, the low_latency setting causes the bug trace below, because
tty_flip_buffer_push() is called within an atomic context and subsequent calls
might sleep due to mutex_lock.

BUG: sleeping function called from invalid context at /root/cvs/linux-2.6.git/kernel/mutex.c:207
in_atomic(): 1, irqs_disabled(): 0, pid: 748, name: khvcd
1 lock held by khvcd/748:
 #0:  (hvc_structs_lock){--..}, at: [<00000000002ceb50>] khvcd+0x58/0x12c
CPU: 0 Not tainted 2.6.29-rc1git #29
Process khvcd (pid: 748, task: 000000002fb9a480, ksp: 000000002f66bd78)
070000000000000a 000000002f66ba00 0000000000000002 (null)
       000000002f66baa0 000000002f66ba18 000000002f66ba18 0000000000104f08
       ffffffffffffc000 000000002f66bd78 (null) (null)
       000000002f66ba00 000000000000000c 000000002f66ba00 000000002f66ba70
       0000000000466af8 0000000000104f08 000000002f66ba00 000000002f66ba50
Call Trace:
([<0000000000104e7c>] show_trace+0x138/0x158)
 [<0000000000104f62>] show_stack+0xc6/0xf8
 [<0000000000105740>] dump_stack+0xb0/0xc0
 [<000000000013144a>] __might_sleep+0x14e/0x17c
 [<000000000045e226>] mutex_lock_nested+0x42/0x3b4
 [<00000000002c443e>] echo_char_raw+0x3a/0x9c
 [<00000000002c688c>] n_tty_receive_buf+0x1154/0x1208
 [<00000000002ca0a2>] flush_to_ldisc+0x152/0x220
 [<00000000002ca1da>] tty_flip_buffer_push+0x6a/0x90
 [<00000000002cea74>] hvc_poll+0x244/0x2c8
 [<00000000002ceb68>] khvcd+0x70/0x12c
 [<000000000015bbd0>] kthread+0x68/0xa0
 [<0000000000109d5a>] kernel_thread_starter+0x6/0xc
 [<0000000000109d54>] kernel_thread_starter+0x0/0xc
1 lock held by khvcd/748:
 #0:  (hvc_structs_lock){--..}, at: [<00000000002ceb50>] khvcd+0x58/0x12c
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The PAPR says that the property for specifying the number of SLBs should
be called "slb-size".  We currently only look for "ibm,slb-size" because
this is what firmware actually presents.

This patch makes us look for the "slb-size" property as well and in
preference to the "ibm,slb-size".  This should future proof us if
firmware changes to match PAPR.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

powerpc: is_hugepage_only_range() must account for both 4kB and 64kB slices

The subpage_prot syscall fails on second and subsequent calls for a given
region, because is_hugepage_only_range() is mis-identifying the 4 kB
slices when the process has a 64 kB page size.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Also some min -> mint_t conversion.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Also a couple of min -> min_t changes.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Fixes compiler warnings:

arch/powerpc/platforms/ps3/mm.c:1205: warning: passing argument 2 of 'ps3_repository_read_mm_info' from incompatible pointer type
arch/powerpc/platforms/ps3/mm.c:1205: warning: passing argument 3 of 'ps3_repository_read_mm_info' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This fixes these compiler warning:

arch/powerpc/platforms/ps3/interrupt.c:109: warning: passing argument 2 of 'clear_bit' from incompatible pointer type
arch/powerpc/platforms/ps3/interrupt.c:130: warning: passing argument 2 of 'set_bit' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

We just fix up the reference parameters as the others are dealt with by
arithmetic promotion rules and don't cause warnings.

This removes warnings like this:

arch/powerpc/platforms/ps3/interrupt.c:327: warning: passing argument 1 of 'lv1_construct_event_receive_port' from incompatible pointer type

Also, these:

drivers/ps3/ps3-vuart.c:462: warning: passing argument 4 of 'ps3_vuart_raw_read' from incompatible pointer type
drivers/ps3/ps3-vuart.c:592: warning: passing argument 4 of 'ps3_vuart_raw_read' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Push the dma_addr_t type usage all the way down to where the actual
values are manipulated.

Now that u64 is "unsigned long long", this removes warnings like:

arch/powerpc/platforms/ps3/system-bus.c:532: warning: passing argument 4 of 'ps3_dma_map' from incompatible pointer type
arch/powerpc/platforms/ps3/system-bus.c:649: warning: passing argument 4 of 'ps3_dma_map' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Also silences this warning:

arch/powerpc/platforms/ps3/setup.c:275: warning: initialization from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This is a powerpc specific driver.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>