This patch fixes the order of mac_up and sgmii_open for the
reasons noted below:

- If open takes more time(if the SGMII block is not responding or
  if we want to do some delay based task) in this situation we
  will hit NETDEV watchdog
- The main reason : We should signal to upper layers that we are
  ready to receive packets "only" when the entire path is initialized
  not the other way around, this is followed in the reset path where
  we do mac_down, sgmii_reset and mac_up. This also makes the driver
  uniform across the reset and open paths.
- In the future there may be need for delay based tasks to be done in
  sgmii open which will result in NETDEV watchdog
- As per the documentation the order of init should be sgmii, mac, rings
  and DMA
Signed-off-by: Hemanth Puranik <hpuranik@codeaurora.org>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

88E1145 also need this autoneg errata.

Fixes: f2899788 ("net: phy: marvell: Limit errata to 88m1101")
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A group member going into state LEAVING should never go back to any
other state before it is finally deleted. However, this might happen
if the socket needs to send out a RECLAIM message during this interval.
Since we forget to remove the leaving member from the group's 'active'
or 'pending' list, the member might be selected for reclaiming, change
state to RECLAIMING, and get stuck in this state instead of being
deleted. This might lead to suppression of the expected 'member down'
event to the receiver.

We fix this by removing the member from all lists, except the RB tree,
at the moment it goes into state LEAVING.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Group messages are not supposed to be returned to sender when the
destination socket disappears. This is done correctly for regular
traffic messages, by setting the 'dest_droppable' bit in the header.
But we forget to do that in group protocol messages. This has the effect
that such messages may sometimes bounce back to the sender, be perceived
as a legitimate peer message, and wreak general havoc for the rest of
the session. In particular, we have seen that a member in state LEAVING
may go back to state RECLAIMED or REMITTED, hence causing suppression
of an otherwise expected 'member down' event to the user.

We fix this by setting the 'dest_droppable' bit even in group protocol
messages.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2017-12-17

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix a corner case in generic XDP where we have non-linear skbs
   but enough tailroom in the skb to not miss to linearizing there,
   from Song.

2) Fix BPF JIT bugs in s390x and ppc64 to not recache skb data when
   BPF context is not skb, from Daniel.

3) Fix a BPF JIT bug in sparc64 where recaching skb data after helper
   call would use the wrong register for the skb, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Stefano Brivio says:
    Commit a985343b ("vxlan: refactor verification and
    application of configuration") introduced a change in the
    behaviour of initial MTU setting: earlier, the MTU for a link
    created on top of a given lower device, without an initial MTU
    specification, was set to the MTU of the lower device minus
    headroom as a result of this path in vxlan_dev_configure():

	if (!conf->mtu)
		dev->mtu = lowerdev->mtu -
			   (use_ipv6 ? VXLAN6_HEADROOM : VXLAN_HEADROOM);

    which is now gone. Now, the initial MTU, in absence of a
    configured value, is simply set by ether_setup() to ETH_DATA_LEN
    (1500 bytes).

    This breaks userspace expectations in case the MTU of
    the lower device is higher than 1500 bytes minus headroom.

This patch restores the previous behaviour on newlink operation. Since
max_mtu can be negative and we update dev->mtu directly, also check it
for valid minimum.
Reported-by: Junhan Yan <juyan@redhat.com>
Fixes: a985343b ("vxlan: refactor verification and application of configuration")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One example of when an ICMPv6 packet is required to be looped back is
when a host acts as both a Multicast Listener and a Multicast Router.

A Multicast Router will listen on address ff02::16 for MLDv2 messages.

Currently, MLDv2 messages originating from a Multicast Listener running
on the same host as the Multicast Router are not being delivered to the
Multicast Router. This is due to dst.input being assigned the default
value of dst_discard.

This results in the packet being looped back but discarded before being
delivered to the Multicast Router.

This patch sets dst.input to ip6_input to ensure a looped back packet
is delivered to the Multicast Router.
Signed-off-by: Brendan McGrath <redmcg@redmandi.dyndns.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull rdma fixes from Jason Gunthorpe:
 "More fixes from testing done on the rc kernel, including more SELinux
  testing. Looking forward, lockdep found regression today in ipoib
  which is still being fixed.

  Summary:

   - Fix for SELinux on the umad SMI path. Some old hardware does not
     fill the PKey properly exposing another bug in the newer SELinux
     code.

   - Check the input port as we can exceed array bounds from this user
     supplied value

   - Users are unable to use the hash field support as they want due to
     incorrect checks on the field restrictions, correct that so the
     feature works as intended

   - User triggerable oops in the NETLINK_RDMA handler

   - cxgb4 driver fix for a bad interaction with CQ flushing in iser
     caused by patches in this merge window, and bad CQ flushing during
     normal close.

   - Unbalanced memalloc_noio in ipoib in an error path"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  IB/ipoib: Restore MM behavior in case of tx_ring allocation failure
  iw_cxgb4: only insert drain cqes if wq is flushed
  iw_cxgb4: only clear the ARMED bit if a notification is needed
  RDMA/netlink: Fix general protection fault
  IB/mlx4: Fix RSS hash fields restrictions
  IB/core: Don't enforce PKey security on SMI MADs
  IB/core: Bound check alternate path port number

Pull i2c fixes from Wolfram Sang:
 "Two bugfixes for the AT24 I2C eeprom driver and some minor corrections
  for I2C bus drivers"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: piix4: Fix port number check on release
  i2c: stm32: Fix copyrights
  i2c-cht-wc: constify platform_device_id
  eeprom: at24: change nvmem stride to 1
  eeprom: at24: fix I2C device selection for runtime PM

Pull NFS client fixes from Anna Schumaker:
 "This has two stable bugfixes, one to fix a BUG_ON() when
  nfs_commit_inode() is called with no outstanding commit requests and
  another to fix a race in the SUNRPC receive codepath.

  Additionally, there are also fixes for an NFS client deadlock and an
  xprtrdma performance regression.

  Summary:

  Stable bugfixes:
   - NFS: Avoid a BUG_ON() in nfs_commit_inode() by not waiting for a
     commit in the case that there were no commit requests.
   - SUNRPC: Fix a race in the receive code path

  Other fixes:
   - NFS: Fix a deadlock in nfs client initialization
   - xprtrdma: Fix a performance regression for small IOs"

* tag 'nfs-for-4.15-3' of git://git.linux-nfs.org/projects/anna/linux-nfs:
  SUNRPC: Fix a race in the receive code path
  nfs: don't wait on commit in nfs_commit_inode() if there were no commit requests
  xprtrdma: Spread reply processing over more CPUs
  nfs: fix a deadlock in nfs client initialization

This reverts commits 5c9d2d5c, c7da82b8, and e7fe7b5c.

We'll probably need to revisit this, but basically we should not
complicate the get_user_pages_fast() case, and checking the actual page
table protection key bits will require more care anyway, since the
protection keys depend on the exact state of the VM in question.

Particularly when doing a "remote" page lookup (ie in somebody elses VM,
not your own), you need to be much more careful than this was.  Dave
Hansen says:

 "So, the underlying bug here is that we now a get_user_pages_remote()
  and then go ahead and do the p*_access_permitted() checks against the
  current PKRU. This was introduced recently with the addition of the
  new p??_access_permitted() calls.

  We have checks in the VMA path for the "remote" gups and we avoid
  consulting PKRU for them. This got missed in the pkeys selftests
  because I did a ptrace read, but not a *write*. I also didn't
  explicitly test it against something where a COW needed to be done"

It's also not entirely clear that it makes sense to check the protection
key bits at this level at all.  But one possible eventual solution is to
make the get_user_pages_fast() case just abort if it sees protection key
bits set, which makes us fall back to the regular get_user_pages() case,
which then has a vma and can do the check there if we want to.

We'll see.

Somewhat related to this all: what we _do_ want to do some day is to
check the PAGE_USER bit - it should obviously always be set for user
pages, but it would be a good check to have back.  Because we have no
generic way to test for it, we lost it as part of moving over from the
architecture-specific x86 GUP implementation to the generic one in
commit e585513b ("x86/mm/gup: Switch GUP to the generic
get_user_page_fast() implementation").

Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: "Jérôme Glisse" <jglisse@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking fixes from David Miller:

 1) Clamp timeouts to INT_MAX in conntrack, from Jay Elliot.

 2) Fix broken UAPI for BPF_PROG_TYPE_PERF_EVENT, from Hendrik
    Brueckner.

 3) Fix locking in ieee80211_sta_tear_down_BA_sessions, from Johannes
    Berg.

 4) Add missing barriers to ptr_ring, from Michael S. Tsirkin.

 5) Don't advertise gigabit in sh_eth when not available, from Thomas
    Petazzoni.

 6) Check network namespace when delivering to netlink taps, from Kevin
    Cernekee.

 7) Kill a race in raw_sendmsg(), from Mohamed Ghannam.

 8) Use correct address in TCP md5 lookups when replying to an incoming
    segment, from Christoph Paasch.

 9) Add schedule points to BPF map alloc/free, from Eric Dumazet.

10) Don't allow silly mtu values to be used in ipv4/ipv6 multicast, also
    from Eric Dumazet.

11) Fix SKB leak in tipc, from Jon Maloy.

12) Disable MAC learning on OVS ports of mlxsw, from Yuval Mintz.

13) SKB leak fix in skB_complete_tx_timestamp(), from Willem de Bruijn.

14) Add some new qmi_wwan device IDs, from Daniele Palmas.

15) Fix static key imbalance in ingress qdisc, from Jiri Pirko.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
  net: qcom/emac: Reduce timeout for mdio read/write
  net: sched: fix static key imbalance in case of ingress/clsact_init error
  net: sched: fix clsact init error path
  ip_gre: fix wrong return value of erspan_rcv
  net: usb: qmi_wwan: add Telit ME910 PID 0x1101 support
  pkt_sched: Remove TC_RED_OFFLOADED from uapi
  net: sched: Move to new offload indication in RED
  net: sched: Add TCA_HW_OFFLOAD
  net: aquantia: Increment driver version
  net: aquantia: Fix typo in ethtool statistics names
  net: aquantia: Update hw counters on hw init
  net: aquantia: Improve link state and statistics check interval callback
  net: aquantia: Fill in multicast counter in ndev stats from hardware
  net: aquantia: Fill ndev stat couters from hardware
  net: aquantia: Extend stat counters to 64bit values
  net: aquantia: Fix hardware DMA stream overload on large MRRS
  net: aquantia: Fix actual speed capabilities reporting
  sock: free skb in skb_complete_tx_timestamp on error
  s390/qeth: update takeover IPs after configuration change
  s390/qeth: lock IP table while applying takeover changes
  ...

Pull USB fixes from Greg KH:
 "Here are some USB fixes for 4.15-rc4.

  There is the usual handful gadget/dwc2/dwc3 fixes as always, for
  reported issues. But the most important things in here is the core fix
  from Alan Stern to resolve a nasty security bug (my first attempt is
  reverted, Alan's was much cleaner), as well as a number of usbip fixes
  from Shuah Khan to resolve those reported security issues.

  All of these have been in linux-next with no reported issues"

* tag 'usb-4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: core: prevent malicious bNumInterfaces overflow
  Revert "USB: core: only clean up what we allocated"
  USB: core: only clean up what we allocated
  Revert "usb: gadget: allow to enable legacy drivers without USB_ETH"
  usb: gadget: webcam: fix V4L2 Kconfig dependency
  usb: dwc2: Fix TxFIFOn sizes and total TxFIFO size issues
  usb: dwc3: gadget: Fix PCM1 for ISOC EP with ep->mult less than 3
  usb: dwc3: of-simple: set dev_pm_ops
  usb: dwc3: of-simple: fix missing clk_disable_unprepare
  usb: dwc3: gadget: Wait longer for controller to end command processing
  usb: xhci: fix TDS for MTK xHCI1.1
  xhci: Don't add a virt_dev to the devs array before it's fully allocated
  usbip: fix stub_send_ret_submit() vulnerability to null transfer_buffer
  usbip: prevent vhci_hcd driver from leaking a socket pointer address
  usbip: fix stub_rx: harden CMD_SUBMIT path to handle malicious input
  usbip: fix stub_rx: get_pipe() to validate endpoint number
  tools/usbip: fixes potential (minor) "buffer overflow" (detected on recent gcc with -Werror)
  USB: uas and storage: Add US_FL_BROKEN_FUA for another JMicron JMS567 ID
  usb: musb: da8xx: fix babble condition handling

Pull staging fixes from Greg KH:
 "Here are some small staging driver fixes for 4.15-rc4.

  One patch for the ccree driver to prevent an unitialized value from
  being returned to a caller, and the other fixes a logic error in the
  pi433 driver"

* tag 'staging-4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: pi433: Fixes issue with bit shift in rf69_get_modulation
  staging: ccree: Uninitialized return in ssi_ahash_import()

Pull virtio regression fixes from Michael Tsirkin:
 "Fixes two issues in the latest kernel"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio_mmio: fix devm cleanup
  ptr_ring: fix up after recent ptr_ring changes

Merge tag 'for-4.15/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm

Pull device mapper fixes from Mike Snitzer:

 - fix a particularly nasty DM core bug in a 4.15 refcount_t conversion.

 - fix various targets to dm_register_target after module __init
   resources created; otherwise racing lvm2 commands could result in a
   NULL pointer during initialization of associated DM kernel module.

 - fix regression in bio-based DM multipath queue_if_no_path handling.

 - fix DM bufio's shrinker to reclaim more than one buffer per scan.

* tag 'for-4.15/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm bufio: fix shrinker scans when (nr_to_scan < retain_target)
  dm mpath: fix bio-based multipath queue_if_no_path handling
  dm: fix various targets to dm_register_target after module __init resources created
  dm table: fix regression from improper dm_dev_internal.count refcount_t conversion

Pull SCSI fixes from James Bottomley:
 "The most important one is the bfa fix because it's easy to oops the
  kernel with this driver (this includes the commit that corrects the
  compiler warning in the original), a regression in the new timespec
  conversion in aacraid and a regression in the Fibre Channel ELS
  handling patch.

  The other three are a theoretical problem with termination in the
  vendor/host matching code and a use after free in lpfc.

  The additional patches are a fix for an I/O hang in the mq code under
  certain circumstances and a rare oops in some debugging code"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: core: Fix a scsi_show_rq() NULL pointer dereference
  scsi: MAINTAINERS: change FCoE list to linux-scsi
  scsi: libsas: fix length error in sas_smp_handler()
  scsi: bfa: fix type conversion warning
  scsi: core: run queue if SCSI device queue isn't ready and queue is idle
  scsi: scsi_devinfo: cleanly zero-pad devinfo strings
  scsi: scsi_devinfo: handle non-terminated strings
  scsi: bfa: fix access to bfad_im_port_s
  scsi: aacraid: address UBSAN warning regression
  scsi: libfc: fix ELS request handling
  scsi: lpfc: Use after free in lpfc_rq_buf_free()

Pull MMC fixes from Ulf Hansson:
 "A couple of MMC fixes:

   - fix use of uninitialized drv_typ variable

   - apply NO_CMD23 quirk to some specific SD cards to make them work"

* tag 'mmc-v4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: core: apply NO_CMD23 quirk to some specific cards
  mmc: core: properly init drv_type

Pull ceph fix from Ilya Dryomov:
 "CephFS inode trimming fix from Zheng, marked for stable"

* tag 'ceph-for-4.15-rc4' of git://github.com/ceph/ceph-client:
  ceph: drop negative child dentries before try pruning inode's alias

Pull overlayfs fixes from Miklos Szeredi:

 - fix incomplete syncing of filesystem

 - fix regression in readdir on ovl over 9p

 - only follow redirects when needed

 - misc fixes and cleanups

* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  ovl: fix overlay: warning prefix
  ovl: Use PTR_ERR_OR_ZERO()
  ovl: Sync upper dirty data when syncing overlayfs
  ovl: update ctx->pos on impure dir iteration
  ovl: Pass ovl_get_nlink() parameters in right order
  ovl: don't follow redirects if redirect_dir=off

Currently mdio read/write takes around ~115us as the timeout
between status check is set to 100us.
By reducing the timeout to 1us mdio read/write takes ~15us to
complete. This improves the link up event response.
Signed-off-by: Hemanth Puranik <hpuranik@codeaurora.org>
Acked-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull arm64 fixes from Will Deacon:
 "There are some significant fixes in here for FP state corruption,
  hardware access/dirty PTE corruption and an erratum workaround for the
  Falkor CPU.

  I'm hoping that things finally settle down now, but never say never...

  Summary:

   - Fix FPSIMD context switch regression introduced in -rc2

   - Fix ABI break with SVE CPUID register reporting

   - Fix use of uninitialised variable

   - Fixes to hardware access/dirty management and sanity checking

   - CPU erratum workaround for Falkor CPUs

   - Fix reporting of writeable+executable mappings

   - Fix signal reporting for RAS errors"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: fpsimd: Fix copying of FP state from signal frame into task struct
  arm64/sve: Report SVE to userspace via CPUID only if supported
  arm64: fix CONFIG_DEBUG_WX address reporting
  arm64: fault: avoid send SIGBUS two times
  arm64: hw_breakpoint: Use linux/uaccess.h instead of asm/uaccess.h
  arm64: Add software workaround for Falkor erratum 1041
  arm64: Define cputype macros for Falkor CPU
  arm64: mm: Fix false positives in set_pte_at access/dirty race detection
  arm64: mm: Fix pte_mkclean, pte_mkdirty semantics
  arm64: Initialise high_memory global variable earlier

Move static key increments to the beginning of the init function
so they pair 1:1 with decrements in ingress/clsact_destroy,
which is called in case ingress/clsact_init fails.

Fixes: 6529eaba ("net: sched: introduce tcf block infractructure")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since in qdisc_create, the destroy op is called when init fails, we
don't do cleanup in init and leave it up to destroy.
This fixes use-after-free when trying to put already freed block.

Fixes: 6e40cf2d ("net: sched: use extended variants of block_get/put in ingress and clsact qdiscs")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull x86 fixes from Ingo Molnar:
 "Misc fixes:

   - fix the s2ram regression related to confusion around segment
     register restoration, plus related cleanups that make the code more
     robust

   - a guess-unwinder Kconfig dependency fix

   - an isoimage build target fix for certain tool chain combinations

   - instruction decoder opcode map fixes+updates, and the syncing of
     the kernel decoder headers to the objtool headers

   - a kmmio tracing fix

   - two 5-level paging related fixes

   - a topology enumeration fix on certain SMP systems"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Resync objtool's instruction decoder source code copy with the kernel's latest version
  x86/decoder: Fix and update the opcodes map
  x86/power: Make restore_processor_context() sane
  x86/power/32: Move SYSENTER MSR restoration to fix_processor_context()
  x86/power/64: Use struct desc_ptr for the IDT in struct saved_context
  x86/unwinder/guess: Prevent using CONFIG_UNWINDER_GUESS=y with CONFIG_STACKDEPOT=y
  x86/build: Don't verify mtools configuration file for isoimage
  x86/mm/kmmio: Fix mmiotrace for page unaligned addresses
  x86/boot/compressed/64: Print error if 5-level paging is not supported
  x86/boot/compressed/64: Detect and handle 5-level paging at boot-time
  x86/smpboot: Do not use smp_num_siblings in __max_logical_packages calculation

Pull locking fixes from Ingo Molnar:
 "Misc fixes:

   - Fix a S390 boot hang that was caused by the lock-break logic.
     Remove lock-break to begin with, as review suggested it was
     unreasonably fragile and our confidence in its continued good
     health is lower than our confidence in its removal.

   - Remove the lockdep cross-release checking code for now, because of
     unresolved false positive warnings. This should make lockdep work
     well everywhere again.

   - Get rid of the final (and single) ACCESS_ONCE() straggler and
     remove the API from v4.15.

   - Fix a liblockdep build warning"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tools/lib/lockdep: Add missing declaration of 'pr_cont()'
  checkpatch: Remove ACCESS_ONCE() warning
  compiler.h: Remove ACCESS_ONCE()
  tools/include: Remove ACCESS_ONCE()
  tools/perf: Convert ACCESS_ONCE() to READ_ONCE()
  locking/lockdep: Remove the cross-release locking checks
  locking/core: Remove break_lock field when CONFIG_GENERIC_LOCKBREAK=y
  locking/core: Fix deadlock during boot on systems with GENERIC_LOCKBREAK

Pull scheduler fixes from Ingo Molnar:
 "Two fixes: a crash fix for an ARM SoC platform, and kernel-doc
  warnings fixes"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/rt: Do not pull from current CPU if only one CPU to pull
  sched/core: Fix kernel-doc warnings after code movement

Pull perf tooling fix from Ingo Molnar:
 "Synchronize kernel <-> tooling headers to resolve two build warnings
  in the perf build"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tools/headers: Synchronize kernel <-> tooling headers

Pull early_ioremap fix from Ingo Molnar:
 "A boot hang fix when the EFI earlyprintk driver is enabled"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  mm/early_ioremap: Fix boot hang with earlyprintk=efi,keep

Pull xen fixes from Juergen Gross:
 "Two minor fixes for running as Xen dom0:

   - when built as 32 bit kernel on large machines the Xen LAPIC
     emulation should report a rather modern LAPIC in order to support
     enough APIC-Ids

   - The Xen LAPIC emulation is needed for dom0 only, so build it only
     for kernels supporting to run as Xen dom0"

* tag 'for-linus-4.15-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen: XEN_ACPI_PROCESSOR is Dom0-only
  x86/Xen: don't report ancient LAPIC version

We must ensure that the call to rpc_sleep_on() in xprt_transmit() cannot
race with the call to xprt_complete_rqst().
Reported-by: Chuck Lever <chuck.lever@oracle.com>
Link: https://bugzilla.linux-nfs.org/show_bug.cgi?id=317
Fixes: ce7c252a ("SUNRPC: Add a separate spinlock to protect..")
Cc: stable@vger.kernel.org # 4.14+
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>

If there were no commit requests, then nfs_commit_inode() should not
wait on the commit or mark the inode dirty, otherwise the following
BUG_ON can be triggered:

[ 1917.130762] kernel BUG at fs/inode.c:578!
[ 1917.130766] Oops: Exception in kernel mode, sig: 5 [#1]
[ 1917.130768] SMP NR_CPUS=2048 NUMA pSeries
[ 1917.130772] Modules linked in: iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi blocklayoutdriver rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace fscache sunrpc sg nx_crypto pseries_rng ip_tables xfs libcrc32c sd_mod crc_t10dif crct10dif_generic crct10dif_common ibmvscsi scsi_transport_srp ibmveth scsi_tgt dm_mirror dm_region_hash dm_log dm_mod
[ 1917.130805] CPU: 2 PID: 14923 Comm: umount.nfs4 Tainted: G               ------------ T 3.10.0-768.el7.ppc64 #1
[ 1917.130810] task: c0000005ecd88040 ti: c00000004cea0000 task.ti: c00000004cea0000
[ 1917.130813] NIP: c000000000354178 LR: c000000000354160 CTR: c00000000012db80
[ 1917.130816] REGS: c00000004cea3720 TRAP: 0700   Tainted: G               ------------ T  (3.10.0-768.el7.ppc64)
[ 1917.130820] MSR: 8000000100029032 <SF,EE,ME,IR,DR,RI>  CR: 22002822  XER: 20000000
[ 1917.130828] CFAR: c00000000011f594 SOFTE: 1
GPR00: c000000000354160 c00000004cea39a0 c0000000014c4700 c0000000018cc750
GPR04: 000000000000c750 80c0000000000000 0600000000000000 04eeb76bea749a03
GPR08: 0000000000000034 c0000000018cc758 0000000000000001 d000000005e619e8
GPR12: c00000000012db80 c000000007b31200 0000000000000000 0000000000000000
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR24: 0000000000000000 c000000000dfc3ec 0000000000000000 c0000005eefc02c0
GPR28: d0000000079dbd50 c0000005b94a02c0 c0000005b94a0250 c0000005b94a01c8
[ 1917.130867] NIP [c000000000354178] .evict+0x1c8/0x350
[ 1917.130871] LR [c000000000354160] .evict+0x1b0/0x350
[ 1917.130873] Call Trace:
[ 1917.130876] [c00000004cea39a0] [c000000000354160] .evict+0x1b0/0x350 (unreliable)
[ 1917.130880] [c00000004cea3a30] [c0000000003558cc] .evict_inodes+0x13c/0x270
[ 1917.130884] [c00000004cea3af0] [c000000000327d20] .kill_anon_super+0x70/0x1e0
[ 1917.130896] [c00000004cea3b80] [d000000005e43e30] .nfs_kill_super+0x20/0x60 [nfs]
[ 1917.130900] [c00000004cea3c00] [c000000000328a20] .deactivate_locked_super+0xa0/0x1b0
[ 1917.130903] [c00000004cea3c80] [c00000000035ba54] .cleanup_mnt+0xd4/0x180
[ 1917.130907] [c00000004cea3d10] [c000000000119034] .task_work_run+0x114/0x150
[ 1917.130912] [c00000004cea3db0] [c00000000001ba6c] .do_notify_resume+0xcc/0x100
[ 1917.130916] [c00000004cea3e30] [c00000000000a7b0] .ret_from_except_lite+0x5c/0x60
[ 1917.130919] Instruction dump:
[ 1917.130921] 7fc3f378 486734b5 60000000 387f00a0 38800003 4bdcb365 60000000 e95f00a0
[ 1917.130927] 694a0060 7d4a0074 794ad182 694a0001 <0b0a0000> 892d02a4 2f890000 40de0134
Signed-off-by: Scott Mayhew <smayhew@redhat.com>
Cc: stable@vger.kernel.org # 4.5+
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>

Commit d8f532d2 ("xprtrdma: Invoke rpcrdma_reply_handler
directly from RECV completion") introduced a performance regression
for NFS I/O small enough to not need memory registration. In multi-
threaded benchmarks that generate primarily small I/O requests,
IOPS throughput is reduced by nearly a third. This patch restores
the previous level of throughput.

Because workqueues are typically BOUND (in particular ib_comp_wq,
nfsiod_workqueue, and rpciod_workqueue), NFS/RDMA workloads tend
to aggregate on the CPU that is handling Receive completions.

The usual approach to addressing this problem is to create a QP
and CQ for each CPU, and then schedule transactions on the QP
for the CPU where you want the transaction to complete. The
transaction then does not require an extra context switch during
completion to end up on the same CPU where the transaction was
started.

This approach doesn't work for the Linux NFS/RDMA client because
currently the Linux NFS client does not support multiple connections
per client-server pair, and the RDMA core API does not make it
straightforward for ULPs to determine which CPU is responsible for
handling Receive completions for a CQ.

So for the moment, record the CPU number in the rpcrdma_req before
the transport sends each RPC Call. Then during Receive completion,
queue the RPC completion on that same CPU.

Additionally, move all RPC completion processing to the deferred
handler so that even RPCs with simple small replies complete on
the CPU that sent the corresponding RPC Call.

Fixes: d8f532d2 ("xprtrdma: Invoke rpcrdma_reply_handler ...")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>

The following deadlock can occur between a process waiting for a client
to initialize in while walking the client list during nfsv4 server trunking
detection and another process waiting for the nfs_clid_init_mutex so it
can initialize that client:

Process 1                               Process 2
---------                               ---------
spin_lock(&nn->nfs_client_lock);
list_add_tail(&CLIENTA->cl_share_link,
        &nn->nfs_client_list);
spin_unlock(&nn->nfs_client_lock);
                                        spin_lock(&nn->nfs_client_lock);
                                        list_add_tail(&CLIENTB->cl_share_link,
                                                &nn->nfs_client_list);
                                        spin_unlock(&nn->nfs_client_lock);
                                        mutex_lock(&nfs_clid_init_mutex);
                                        nfs41_walk_client_list(clp, result, cred);
                                        nfs_wait_client_init_complete(CLIENTA);
(waiting for nfs_clid_init_mutex)

Make sure nfs_match_client() only evaluates clients that have completed
initialization in order to prevent that deadlock.

This patch also fixes v4.0 trunking behavior by not marking the client
NFS_CS_READY until the clientid has been confirmed.
Signed-off-by: Scott Mayhew <smayhew@redhat.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>

If pskb_may_pull return failed, return PACKET_REJECT instead of -ENOMEM.

Fixes: 84e54fe0 ("gre: introduce native tunnel support for ERSPAN")
Cc: William Tu <u9012063@gmail.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for Telit ME910 PID 0x1101.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
net: sched: Make qdisc offload uapi uniform

Several qdiscs can already be offloaded to hardware, but there's an
inconsistecy in regard to the uapi through which they indicate such
an offload is taking place - indication is passed to the user via
TCA_OPTIONS where each qdisc retains private logic for setting it.

The recent addition of offloading to RED in
602f3baf ("net_sch: red: Add offload ability to RED qdisc") caused
the addition of yet another uapi field for this purpose -
TC_RED_OFFLOADED.

For clarity and prevention of bloat in the uapi we want to eliminate
said added uapi, replacing it with a common mechanism that can be used
to reflect offload status of the various qdiscs.

The first patch introduces TCA_HW_OFFLOAD as the generic message meant
for this purpose. The second changes the current RED implementation into
setting the internal bits necessary for passing it, and the third removes
TC_RED_OFFLOADED as its no longer needed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Following the previous patch, RED is now using the new uniform uapi
for indicating it's offloaded. As a result, TC_RED_OFFLOADED is no
longer utilized by kernel and can be removed [as it's still not
part of any stable release].

Fixes: 602f3baf ("net_sch: red: Add offload ability to RED qdisc")
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Let RED utilize the new internal flag, TCQ_F_OFFLOADED,
to mark a given qdisc as offloaded instead of using a dedicated
indication.

Also, change internal logic into looking at said flag when possible.

Fixes: 602f3baf ("net_sch: red: Add offload ability to RED qdisc")
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Qdiscs can be offloaded to HW, but current implementation isn't uniform.
Instead, qdiscs either pass information about offload status via their
TCA_OPTIONS or omit it altogether.

Introduce a new attribute - TCA_HW_OFFLOAD that would form a uniform
uAPI for the offloading status of qdiscs.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>