We already have the same functionality in usercopy_32.c. Share it with
64-bit and get rid of some more asm glue which is not needed anymore.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20161031151015.22087-1-bp@alien8.deSigned-off-by: Ingo Molnar <mingo@kernel.org>

Signed-off-by: Ingo Molnar <mingo@kernel.org>

Pull spi fixes from Mark Brown: "A few small fixes for SPI, one core fix
  that only applies in cases where we're handling DT overlays and a
  couple of driver specific fixes:

   - Fix handling of error cases when instantiating DT overlays so we
     don't end up just ignoring devices that encountered an error during
     instantiation.

   - Avoid reading uninitialized data when handing spurious interrupts
     in the espi driver.

   - A driver specific fix for the dspi driver to fix a bad interaction
     with u-boot"

* tag 'spi-fix-v4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: dspi: clear SPI_SR before enable interrupt
  spi: fsl-espi: avoid processing uninitalized data on error
  spi: mark device nodes only in case of successful instantiation

Merge tag 'regulator-fix-v4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

Pull regulator fix from Mark Brown:
 "Fix ramp_delay warnings for v4.9

  A new warning was introduced for missing information about the time
  that regulators take to power on in v4.9. This is in theory a real
  issue but for most practical regulators the communication overhead of
  talking to the device is greater than the ramp time so a lot of
  drivers don't set it and the warning is far too noisy without
  identifying practical issues.

  Just remove the warning for now"

* tag 'regulator-fix-v4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: core: silence warning: "VDD1: ramp_delay not set"

Pull regmap fixes from Mark Brown:
 "A couple of small build fixes here, nothing major.

  The missing include is triggered in some configurations and the
  renaming of ret is defensive for the benefit of some drivers people
  are in the process of mainlining"

* tag 'regmap-fix-v4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: Rename ret variable in regmap_read_poll_timeout
  regmap: include <linux/delay.h> from include/linux/regmap.h

Pull TPM fix from James Morris.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  tpm: remove invalid min length check from tpm_do_selftest()

Removal of this check was not properly amended to the original commit.

Cc: stable@vger.kernel.org
Fixes: 0c541332 ("tpm: use tpm_pcr_read_dev() in tpm_do_selftest()")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>

Pull ARM fixes from Russell King:
 "A fix for a regression on ARMv4T CPUs, and wiring up the new pkey
  syscalls for ARM"

* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: wire up new pkey syscalls
  ARM: fix oops when using older ARMv4T CPUs

Pull sparc fixes from David Miller:
 "Several sparc64 bug fixes here:

  1) Make the user copy routines on sparc64 return a properly accurate
     residual length when an exception occurs.

  2) We can get enormous kernel TLB range flush requests from vmalloc
     unmaps, so handle these more gracefully by doing full flushes
     instead of going page-by-page.

  3) Cope properly with negative branch offsets in sparc jump-label
     support, from James Clarke.

  4) Some old-style decl GCC warning fixups from Tobias Klauser"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Handle extremely large kernel TLB range flushes more gracefully.
  sparc64: Fix illegal relative branches in hypervisor patched TLB cross-call code.
  sparc64: Fix instruction count in comment for __hypervisor_flush_tlb_pending.
  sparc64: Handle extremely large kernel TSB range flushes sanely.
  sparc: Handle negative offsets in arch_jump_label_transform
  sparc64: Fix illegal relative branches in hypervisor patched TLB code.
  sparc64: Delete now unused user copy fixup functions.
  sparc64: Delete now unused user copy assembler helpers.
  sparc64: Convert U3copy_{from,to}_user to accurate exception reporting.
  sparc64: Convert NG2copy_{from,to}_user to accurate exception reporting.
  sparc64: Convert NGcopy_{from,to}_user to accurate exception reporting.
  sparc64: Convert NG4copy_{from,to}_user to accurate exception reporting.
  sparc64: Convert U1copy_{from,to}_user to accurate exception reporting.
  sparc64: Convert GENcopy_{from,to}_user to accurate exception reporting.
  sparc64: Convert copy_in_user to accurate exception reporting.
  sparc64: Prepare to move to more saner user copy exception handling.
  sparc64: Delete __ret_efault.
  sparc32: Fix old style declaration GCC warnings
  sparc64: Fix old style declaration GCC warnings
  sparc64: Setup a scheduling domain for highest level cache.

Pull networking fixes from David Miller:
 "Lots of fixes, mostly drivers as is usually the case.

   1) Don't treat zero DMA address as invalid in vmxnet3, from Alexey
      Khoroshilov.

   2) Fix element timeouts in netfilter's nft_dynset, from Anders K.
      Pedersen.

   3) Don't put aead_req crypto struct on the stack in mac80211, from
      Ard Biesheuvel.

   4) Several uninitialized variable warning fixes from Arnd Bergmann.

   5) Fix memory leak in cxgb4, from Colin Ian King.

   6) Fix bpf handling of VLAN header push/pop, from Daniel Borkmann.

   7) Several VRF semantic fixes from David Ahern.

   8) Set skb->protocol properly in ip6_tnl_xmit(), from Eli Cooper.

   9) Socket needs to be locked in udp_disconnect(), from Eric Dumazet.

  10) Div-by-zero on 32-bit fix in mlx4 driver, from Eugenia Emantayev.

  11) Fix stale link state during failover in NCSCI driver, from Gavin
      Shan.

  12) Fix netdev lower adjacency list traversal, from Ido Schimmel.

  13) Propvide proper handle when emitting notifications of filter
      deletes, from Jamal Hadi Salim.

  14) Memory leaks and big-endian issues in rtl8xxxu, from Jes Sorensen.

  15) Fix DESYNC_FACTOR handling in ipv6, from Jiri Bohac.

  16) Several routing offload fixes in mlxsw driver, from Jiri Pirko.

  17) Fix broadcast sync problem in TIPC, from Jon Paul Maloy.

  18) Validate chunk len before using it in SCTP, from Marcelo Ricardo
      Leitner.

  19) Revert a netns locking change that causes regressions, from Paul
      Moore.

  20) Add recursion limit to GRO handling, from Sabrina Dubroca.

  21) GFP_KERNEL in irq context fix in ibmvnic, from Thomas Falcon.

  22) Avoid accessing stale vxlan/geneve socket in data path, from
      Pravin Shelar"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (189 commits)
  geneve: avoid using stale geneve socket.
  vxlan: avoid using stale vxlan socket.
  qede: Fix out-of-bound fastpath memory access
  net: phy: dp83848: add dp83822 PHY support
  enic: fix rq disable
  tipc: fix broadcast link synchronization problem
  ibmvnic: Fix missing brackets in init_sub_crq_irqs
  ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context
  Revert "ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context"
  arch/powerpc: Update parameters for csum_tcpudp_magic & csum_tcpudp_nofold
  net/mlx4_en: Save slave ethtool stats command
  net/mlx4_en: Fix potential deadlock in port statistics flow
  net/mlx4: Fix firmware command timeout during interrupt test
  net/mlx4_core: Do not access comm channel if it has not yet been initialized
  net/mlx4_en: Fix panic during reboot
  net/mlx4_en: Process all completions in RX rings after port goes up
  net/mlx4_en: Resolve dividing by zero in 32-bit system
  net/mlx4_core: Change the default value of enable_qos
  net/mlx4_core: Avoid setting ports to auto when only one port type is supported
  net/mlx4_core: Fix the resource-type enum in res tracker to conform to FW spec
  ...

This patch is similar to earlier vxlan patch.
Geneve device close operation frees geneve socket. This
operation can race with geneve-xmit function which
dereferences geneve socket. Following patch uses RCU
mechanism to avoid this situation.
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When vxlan device is closed vxlan socket is freed. This
operation can race with vxlan-xmit function which
dereferences vxlan socket. Following patch uses RCU
mechanism to avoid this situation.
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver allocates a shadow array for transmitted SKBs with X entries;
That means valid indices are {0,...,X - 1}. [X == 8191]
Problem is the driver also uses X as a mask for a
producer/consumer in order to choose the right entry in the
array which allows access to entry X which is out of bounds.

To fix this, simply allocate X + 1 entries in the shadow array.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This PHY has a compatible register set with DP83848x so
add support for it.
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When MTU is changed from 9000 to 1500 while there is burst of inbound 9000
bytes packets, adaptor sometimes delivers 9000 bytes packets to 1500 bytes
buffers. This causes memory corruption and sometimes crash.

This is because of a race condition in adaptor between "RQ disable"
clearing descriptor mini-cache and mini-cache valid bit being set by
completion of descriptor fetch. This can result in stale RQ desc being
cached and used when packets arrive. In this case, the stale descriptor
have old MTU value.

Solution is to write RQ->disable twice. The first write will stop any
further desc fetches, allowing the second disable to clear the mini-cache
valid bit without danger of a race.

Also, the check for rq->running becoming 0 after writing rq->enable to 0
is not done properly. When incoming packets are flooding the interface,
rq->running will pulse high for each dropped packet. Since the driver was
waiting for 10us between each poll, it is possible to see rq->running = 1
1000 times in a row, even though it is not actually stuck running.
This results in false failure of vnic_rq_disable(). Fix is to try more
than 1000 time without delay between polls to ensure we do not miss when
running goes low.

In old adaptors rq->enable needs to be re-written to 0 when posted_index
is reset in vnic_rq_clean() in order to keep rq->prefetch_index in sync.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 2d18ac4b ("tipc: extend broadcast link initialization
criteria") we tried to fix a problem with the initial synchronization
of broadcast link acknowledge values. Unfortunately that solution is
not sufficient to solve the issue.

We have seen it happen that LINK_PROTOCOL/STATE packets with a valid
non-zero unicast acknowledge number may bypass BCAST_PROTOCOL
initialization, NAME_DISTRIBUTOR and other STATE packets with invalid
broadcast acknowledge numbers, leading to premature opening of the
broadcast link. When the bypassed packets finally arrive, they are
inadvertently accepted, and the already correctly initialized
acknowledge number in the broadcast receive link is overwritten by
the invalid (zero) value of the said packets. After this the broadcast
link goes stale.

We now fix this by marking the packets where we know the acknowledge
value is or may be invalid, and then ignoring the acks from those.

To this purpose, we claim an unused bit in the header to indicate that
the value is invalid. We set the bit to 1 in the initial BCAST_PROTOCOL
synchronization packet and all initial ("bulk") NAME_DISTRIBUTOR
packets, plus those LINK_PROTOCOL packets sent out before the broadcast
links are fully synchronized.

This minor protocol update is fully backwards compatible.
Reported-by: John Thompson <thompa.atl@gmail.com>
Tested-by: John Thompson <thompa.atl@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Schedule these XPORT event tasks in the shared workqueue
so that IRQs are not freed in an interrupt context when
sub-CRQs are released.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 8d7533e5.

It introduced kbuild failures, new version coming.
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2016-10-27

This series contains fixes to ixgbe and i40e.

Emil fixes a NULL pointer dereference when a macvlan interface is brought
up while the PF is still down.

David root caused the original panic that was fixed by commit id
(a036244c "i40e: Fix kernel panic on enable/disable LLDP") and the
fix was not quite correct, so removed the get_default_tc() and replaced
it with a #define since there is only one TC supported as a default.

Guilherme Piccoli fixes an issue where if we modprobe the driver module
without enough MSI-X interrupts, then unload the module and reload it
again, the kernel would crash.  So if we fail to allocate enough MSI-X
interrupts, we should disable them since they were previously enabled.

Huaibin Wang found that the order of the arguments for
ndo_dflt_bridge_getlink() were in the correct order, so fix the order.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 01cfbad7 "ipv4: Update parameters for csum_tcpudp_magic to their
original types" changed parameters for csum_tcpudp_magic and
csum_tcpudp_nofold for many platforms but not for PowerPC.

Fixes: 01cfbad7 "ipv4: Update parameters for csum_tcpudp_magic to their original types"
Cc: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull x86 bugfix from Thomas Gleixner:
 "A single bugfix for the recent changes related to registering the boot
  cpu when this has not happened before prefill_possible_map().

  The main problem with this change got fixed already, but we missed the
  case where the local APIC is not yet mapped, when prefill_possible_map()
  is invoked, so the registration of the boot cpu which has the APIC bit
  set in CPUID will explode.

  I should have seen that issue earlier, but all I can do now is feeling
  embarassed"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/smpboot: Init apic mapping before usage

Tariq Toukan says:

====================
mlx4 misc fixes for 4.9

This patchset contains several bug fixes from the team to the
mlx4 Eth and Core drivers.

Series generated against net commit:
ecc515d7 'sctp: fix the panic caused by route update'
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Following the previous patch, as an optimization, the slave will
not even bother sending the DUMP_ETH_STATS command over the
comm channel.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4_en_DUMP_ETH_STATS took the *counter mutex* and then
called the FW command, with WRAPPED attribute. As a result, the fw command
is wrapped on the Hypervisor when it calls mlx4_en_DUMP_ETH_STATS.
The FW command wrapper flow on the hypervisor takes the *slave_cmd_mutex*
during processing.

At the same time, a VF could be in the process of coming up, and could
call mlx4_QUERY_FUNC_CAP.  On the hypervisor, the command flow takes the
*slave_cmd_mutex*, then executes mlx4_QUERY_FUNC_CAP_wrapper.
mlx4_QUERY_FUNC_CAP wrapper calls mlx4_get_default_counter_index(),
which takes the *counter mutex*. DEADLOCK.

The fix is that the DUMP_ETH_STATS fw command should be called with
the NATIVE attribute, so that on the hypervisor, this command does not
enter the wrapper flow.

Since the Hypervisor no longer goes through the wrapper code, we also
simply return 0 in mlx4_DUMP_ETH_STATS_wrapper (i.e.the function succeeds,
but the returned data will be all zeroes).
No need to test if it is the Hypervisor going through the wrapper.

Fixes: f9baff50 ("mlx4_core: Add "native" argument to mlx4_cmd ...")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently interrupt test that is part of ethtool selftest runs the
check over all interrupt vectors of the device.
In mlx4_en package part of interrupt vectors are uninitialized since
mlx4_ib doesn't exist. This causes NOP FW command to time out.
Change logic to test current port interrupt vectors only.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the Hypervisor, there are several FW commands which are invoked
before the comm channel is initialized (in mlx4_multi_func_init).
These include MOD_STAT_CONFIG, QUERY_DEV_CAP, INIT_HCA, and others.

If any of these commands fails, say with a timeout, the Hypervisor
driver enters the internal error reset flow. In this flow, the driver
attempts to notify all slaves via the comm channel that an internal error
has occurred.

Since the comm channel has not yet been initialized (i.e., mapped via
ioremap), this will cause dereferencing a NULL pointer.

To fix this, do not access the comm channel in the internal error flow
if it has not yet been initialized.

Fixes: 55ad3592 ("net/mlx4_core: Enable device recovery flow with SRIOV")
Fixes: ab9c17a0 ("mlx4_core: Modify driver initialization flow to accommodate SRIOV for Ethernet")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a kernel panic that occurs as a result of an asynchronous event
handled in roce_gid_mgmt:
mlx4_en_get_drvinfo is called and accesses freed resources.

This happens in a shutdown flow only, since pci device is destroyed
while netdevice is still alive.

Fixes: c27a02cd ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC")
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently there is a race between incoming traffic and
initialization flow. HW is able to receive the packets
after INIT_PORT is done and unicast steering is configured.
Before we set priv->port_up NAPI is not scheduled and
receive queues become full. Therefore we never get
new interrupts about the completions.
This issue could happen if running heavy traffic during
bringing port up.
The resolution is to schedule NAPI once port_up is set.
If receive queues were full this will process all cqes
and release them.

Fixes: c27a02cd ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When doing roundup_pow_of_two for large enough number with
bit 31, an overflow will occur and a value equal to 1 will
be returned. In this case 1 will be subtracted from the return
value and division by zero will be reached.

Fixes: 31c128b6 ("net/mlx4_en: Choose time-stamping shift value according to HW frequency")
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the default status of quality of service back to disabled,
as it hurts performance in some cases.

Fixes: 38438f7c ("net/mlx4: Set enhanced QoS support by default when ...")
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When only one port type is supported, it should be read only.
We reject changing requests, even to the auto sense mode.

Fixes: 27bf91d6 ("mlx4_core: Add link type autosensing")
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The resource type enum in the resource tracker was incorrect.
RES_EQ was put in the position of RES_NPORT_ID (a FC resource).

Since the remaining resources maintain their current values,
and RES_EQ is not passed from slaves to the hypervisor in any
FW command, this change affects only the hypervisor.
Therefore, there is no backwards-compatibility issue.

Fixes: 623ed84b ("mlx4_core: initial header-file changes for SRIOV support")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull ubi/ubifs fixes from Richard Weinberger:
 "This contains fixes for issues in both UBI and UBIFS:

   - A regression wrt overlayfs, introduced in -rc2.
   - An UBI issue, found by Dan Carpenter's static checker"

* tag 'upstream-4.9-rc3' of git://git.infradead.org/linux-ubifs:
  ubifs: Fix regression in ubifs_readdir()
  ubi: fastmap: Fix add_vol() return value test in ubi_attach_fastmap()

rds use Kconfig option called "RDS_DEBUG" to enable rds debug messages.
This option cause the rds Makefile to add -DDEBUG to the rds gcc command
line.

When CONFIG_DYNAMIC_DEBUG is enabled, the "DEBUG" macro is used by
include/linux/dynamic_debug.h to decide if dynamic debug prints should
be sent by default to the kernel log.

rds should not enable this macro for production builds. rds dynamic
debug work as expected follow this fix.
Signed-off-by: Shamir Rabinovitch <shamir.rabinovitch@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Reviewed-by: Wengang Wang <wen.gang.wang@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2016-10-27' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Just two fixes:
 * a fix to process all events while suspending, so any
   potential calls into the driver are done before it is
   suspended
 * small markup fixes for the sphinx documentation conversion
   that's coming into the tree via the doc tree
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Schedule these XPORT event tasks in the shared workqueue
so that IRQs are not freed in an interrupt context when
sub-CRQs are released.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MAC is capable of RGMII mode and that is probably a more typical
connection type than GMII today (eg it is used by Marvell Reference
designs for several SOCs). Let DT users specify the standard

   phy-connection-type = "rgmii-id";

On a phy node.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull ARM SoC fixes from Olof Johansson:
 "We haven't seen a whole lot of fixes for the first two weeks since the
  merge window, but here is the batch that we have at the moment.

  Nothing sticks out as particularly bad or scary, it's mostly a handful
  of smaller fixes to several platforms. The Uniphier reset controller
  changes could probably have been delayed to 4.10, but they're not
  scary and just plumbing up driver changes that went in during the
  merge window.

  We're also adding another maintainer to Marvell Berlin platforms, to
  help out when Sebastian is too busy. Yay teamwork!"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: imx: mach-imx6q: Fix the PHY ID mask for AR8031
  ARM: dts: vf610: fix IRQ flag of global timer
  ARM: imx: gpc: Fix the imx_gpc_genpd_init() error path
  ARM: imx: gpc: Initialize all power domains
  arm64: dts: Updated NAND DT properties for NS2 SVK
  arm64: dts: uniphier: change MIO node to SD control node
  ARM: dts: uniphier: change MIO node to SD control node
  reset: uniphier: rename MIO reset to SD reset for Pro5, PXs2, LD20 SoCs
  arm64: uniphier: select ARCH_HAS_RESET_CONTROLLER
  ARM: uniphier: select ARCH_HAS_RESET_CONTROLLER
  arm64: dts: Add timer erratum property for LS2080A and LS1043A
  arm64: dts: rockchip: remove the abuse of keep-power-in-suspend
  ARM: multi_v7_defconfig: Enable Intel e1000e driver
  MAINTAINERS: add myself as Marvell berlin SoC maintainer
  bus: qcom-ebi2: depend on ARCH_QCOM or COMPILE_TEST
  ARM: dts: fix the SD card on the Snowball
  arm64: dts: rockchip: remove always-on and boot-on from vcc_sd
  arm64: dts: marvell: fix clocksource for CP110 master SPI0
  ARM: mvebu: Select corediv clk for all mvebu v7 SoC