Convert the PM sysdev to syscore_ops and clean up the ddma addresses a bit.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2351/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Convert the PM sysdev to use syscore_ops instead.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2350/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

replace au_readl/au_writel with __raw_readl/__raw_writel,
and clean up IC-related stuff from the headers.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2354/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This fixes a build failure with gpio_keys and CONFIG_GPIOLIB=n (mtx1):
  CC      drivers/input/keyboard/gpio_keys.o
gpio_keys.c: In function 'gpio_keys_report_event':
gpio_keys.c:325:2: error: implicit declaration of function 'gpio_get_value_cansleep'
gpio_keys.c: In function 'gpio_keys_setup_key':
gpio_keys.c:390:3: error: implicit declaration of function 'gpio_set_debounce'

Also add stubs for the other new functions.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2346/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Setting Config[OD] gets rid of a _LOT_ of spurious CPLD interrupts,
but also decreases overall performance a bit.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2347/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This patch adds the driver for the watchdog found inside the Lantiq SoC family.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-mips@linux-mips.org
Cc: linux-watchdog@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2327/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Register the etop platform device inside the machtype specific init code.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2356/
Patchwork: https://patchwork.linux-mips.org/patch/2370/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This patch adds the driver for the ETOP Packet Processing Engine (PPE32)
found inside the XWAY family of Lantiq MIPS SoCs. This driver makes 100MBit
ethernet work. Support for all 8 dma channels, gbit and the embedded switch
found on the ar9/vr9 still needs to be implemented.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2357/Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This patch adds support for the DMA engine found inside the XWAY family of
SoCs. The engine has 5 ports and 20 channels.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2355/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: alan@lxorguk.ukuu.org.uk
Cc: linux-mips@linux-mips.org
Cc: linux-serial@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2269/Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The XWAY family allows to extend the number of gpios by using shift
registers or latches. This patch adds the 2 drivers needed for this. The
extended gpios are output only.

[ralf@linux-mips.org: Fixed ltq_stp_probe section() attributes.]
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2258/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This patch adds mach specific code for the Lantiq EASY50712/50601 evaluation
boards
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2255/
Patchwork: https://patchwork.linux-mips.org/patch/2361/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This patch adds support for Gabor's mips_machine patch.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2251/
Patchwork: https://patchwork.linux-mips.org/patch/2358/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This patch adds the wrappers for registering our platform devices.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2254/
Patchwork: https://patchwork.linux-mips.org/patch/2360/
Patchwork: https://patchwork.linux-mips.org/patch/2359/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This patch adds the driver/map for NOR devices attached to the SoC via the
External Bus Unit (EBU).
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-mtd@lists.infradead.org
Acked-by: Artem Bityutskiy <dedekind1@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/2285/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The Lantiq family of SoCs have a EBU (External Bus Unit). This patch adds
the driver that allows us to use the EBU as a PCI controller. In order for
PCI to work the EBU is set to endianess swap all the data. In addition we
need to make use of SWAP_IO_SPACE for device->host DMA to work.

The clock of the PCI works in several modes (internal/external). If this
is not configured correctly the SoC will hang.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2250/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add support for the Lantiq XWAY family of Mips24KEc SoCs.

* Danube (PSB50702)
* Twinpass (PSB4000)
* AR9 (PSB50802)
* Amazon SE (PSB5061)

The Amazon SE is a lightweight SoC and has no PCI as well as a different
clock. We split the code out into seperate files to handle this.

The GPIO pins on the SoCs are multi function and there are several bits
we can use to configure the pins. To be as compatible as possible to
GPIOLIB we add a function

int lq_gpio_request(unsigned int pin, unsigned int alt0,
        unsigned int alt1, unsigned int dir, const char *name);

which lets you configure the 2 "alternate function" bits. This way drivers like
PCI can make use of GPIOLIB without a cubersome wrapper.

The PLL code inside arch/mips/lantiq/xway/clk-xway.c is voodoo to me. It was
taken from a 2.4.20 source tree and was never really changed by me since then.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2249/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add initial support for Mips based SoCs made by Lantiq. This series will add
support for the XWAY family.

The series allows booting a minimal system using a initramfs or NOR. Missing
drivers and support for Amazon and GPON family will be provided in a later
series.

[Ralf: Remove some cargo cult programming and fixed formatting.]
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2252/
Patchwork: https://patchwork.linux-mips.org/patch/2371/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Maxin B. John <maxin.john@gmail.com>
To: Catalin Marinas <catalin.marinas@arm.com>
Cc: Daniel Baluta <dbaluta@ixiacom.com>
Cc: naveen yadav <yad.naveen@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mm@kvack.org
Patchwork: https://patchwork.linux-mips.org/patch/2244/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Adds pci/pci-xlr.c to support for XLR PCI/PCI-X interface and XLS PCIe
interface.
Update irq.c to ack PCI interrupts, use irq handler data to do the
PCI/PCIe bus ack.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2337/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Enable XLR CPU support, SMP, initramfs based root filesystem etc.

[ralf@linux-mips.org: shrink the defconfig file through make savedefconfig.]
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2338/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add NLM_XLR_BOARD, CPU_XLR and other config options
Makefile updates, mostly based on r4k
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2334/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

* include/asm/netlogic added with files common for all Netlogic processors
  (common with XLP which will be added later)
* include/asm/netlogic/xlr for XLR/XLS chip specific files
* netlogic/xlr for XLR/XLS platform files
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2334/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

CPU_XLR case added to mm/tlbex.c
CPU_XLR case added to mm/c-r4k.c for PINDEX attribute
Feature overrides for XLR cpu.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2333/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add war.h and irq.h with XLR/XLS definitions.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2331/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add Netlogic Microsystems company ID and processor IDs for XLR
and XLS processors for CPU probe. Add CPU_XLR to cpu_type_enum.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc:     linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2367/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
  configfs: Fix race between configfs_readdir() and configfs_d_iput()
  configfs: Don't try to d_delete() negative dentries.
  ocfs2/dlm: Target node death during resource migration leads to thread spin
  ocfs2: Skip mount recovery for hard-ro mounts
  ocfs2/cluster: Heartbeat mismatch message improved
  ocfs2/cluster: Increase the live threshold for global heartbeat
  ocfs2/dlm: Use negotiated o2dlm protocol version
  ocfs2: skip existing hole when removing the last extent_rec in punching-hole codes.
  ocfs2: Initialize data_ac (might be used uninitialized)

* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6:
  drivercore: revert addition of of_match to struct device
  of: fix race when matching drivers

* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
  MIPS: Kludge IP27 build for 2.6.39.
  MIPS: AR7: Fix GPIO register size for Titan variant.
  MIPS: Fix duplicate invocation of notify_die.
  MIPS: RB532: Fix iomap resource size miscalculation.

Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time.  This was unsafe
because matching is not an atomic operation with probing a driver.  If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.

This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

If two drivers are probing devices at the same time, both will write
their match table result to the dev->of_match cache at the same time.

Only write the result if the device matches.

In a thread titled "SBus devices sometimes detected, sometimes not",
Meelis reported his SBus hme was not detected about 50% of the time.
From the debug suggested by Grant it was obvious another driver matched
some devices between the call to match the hme and the hme discovery
failling.
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Milton Miller <miltonm@bga.com>
[grant.likely: modified to only call of_match_device() once]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  block: don't delay blk_run_queue_async
  scsi: remove performance regression due to async queue run
  blk-throttle: Use task_subsys_state() to determine a task's blkio_cgroup
  block: rescan partitions on invalidated devices on -ENOMEDIA too
  cdrom: always check_disk_change() on open
  block: unexport DISK_EVENT_MEDIA_CHANGE for legacy/fringe drivers

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The 'size' variable contains the correct register size for both AR7
and Titan, but we never used it to ioremap the correct register size.
This problem only shows up on Titan.

[ralf@linux-mips.org: Fixed the fix.  The original patch as in patchwork
recognizes the problem correctly then fails to fix it ...]
Reported-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/2380/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Initial patch by Yury Polyanskiy <ypolyans@princeton.edu>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2373/

This is the MIPS portion of Joe Perches <joe@perches.com>'s
https://patchwork.linux-mips.org/patch/2172/ which seems to have been
lost in time and space.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>