TBU interrupt is a normal interrupt and can be used to trigger the
cleaning of TX path. Lets check if it's active in DMA interrupt handler.

While at it, refactor a little bit the function:
	- Don't check if RI is enabled because at function exit we will
	  only clear the interrupts that are enabled so, no event will
	  be missed.

In my tests withe XGMAC2 this increased performance.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TBU interrupt is a normal interrupt and can be used to trigger the
cleaning of TX path. Lets check if it's active in DMA interrupt handler.

While at it, refactor a little bit the function:
	- Don't check if RI is enabled because at function exit we will
	  only clear the interrupts that are enabled so, no event will be
	  missed.

In my tests with GMAC5 this increased performance.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 8fce3331 introduced the concept of NAPI per-channel and
independent cleaning of TX path.

This is currently breaking performance in some cases. The scenario
happens when all packets are being received in Queue 0 but the TX is
performed in Queue != 0.

Fix this by using different NAPI instances per each TX and RX queue, as
suggested by Florian.

Changes from v2:
	- Only force restart transmission if there are pending packets
Changes from v1:
	- Pass entire ring size to TX clean path (Florian)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: Get rid of switchdev_port_attr_get()

This patch series splits the removal of the switchdev_ops that was
proposed a few times before and first tackles the easy part which is the
removal of the single call to switchdev_port_attr_get() within the
bridge code.

As suggestd by Ido, this patch series adds a
SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS which is used in the same
context as the caller of switchdev_port_attr_set(), so not deferred, and
then the operation is carried out in deferred context with setting a
support bridge port flag.

Follow-up patches will do the switchdev_ops removal after introducing
the proper helpers for the switchdev blocking notifier to work across
stacked devices (unlike the previous submissions).

David this does depend on Russell's "[PATCH net-next v5 0/3] net: dsa:
mv88e6xxx: fix IPv6".

Changes in v3:

- rebased against net-next/master after Russell's IPv6 changes to DSA
- ignore prepare/commit phase for PRE_BRIDGE_FLAGS since we don't
  want to trigger the WARN() in net/switchdev/switchdev.c in the commit
  phase

Changes in v2:

- differentiate callers not supporting switchdev_port_attr_set() from
  the driver not being able to support specific bridge flags

- pass "mask" instead of "flags" for the PRE_BRIDGE_FLAGS check

- skip prepare phase for PRE_BRIDGE_FLAGS

- corrected documentation a bit more

- tested bridge_vlan_aware.sh with veth/VRF
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

With the bridge no longer calling switchdev_port_attr_get() to obtain
the supported bridge port flags from a driver but instead trying to set
the bridge port flags directly and relying on driver to reject
unsupported configurations, we can effectively get rid of
switchdev_port_attr_get() entirely since this was the only place where
it was called.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we have converted the bridge code and the drivers to check for
bridge port(s) flags at the time we try to set them, there is no need
for a get() -> set() sequence anymore and
SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS_SUPPORT therefore becomes unused.
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that all switchdev drivers have been converted to check the
SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS flags and report flags that they
do not support accordingly, we can migrate the bridge code to try to set
that attribute first, check the results and then do the actual setting.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for getting rid of switchdev_port_attr_get(), have rocker
check for the bridge flags being set through switchdev_port_attr_set()
with the SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS attribute identifier.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for removing SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS_SUPPORT,
add support for a function that processes the
SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS and
SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS attributes and returns not
supported for any flag set, since DSA does not currently support
toggling those bridge port attributes (yet).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for removing SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS_SUPPORT,
handle the SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS attribute and check
that the bridge port flags being configured are supported.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for getting rid of switchdev_port_attr_get(), have mlxsw
check for the bridge flags being set through switchdev_port_attr_set()
when the SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS attribute identifier is
used.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for removing switchdev_port_attr_get(), introduce
PORT_PRE_BRIDGE_FLAGS which will be called through
switchdev_port_attr_set(), in the caller's context (possibly atomic) and
which must be checked by the switchdev driver in order to return whether
the operation is supported or not.

This is entirely analoguous to how the BRIDGE_FLAGS_SUPPORT works,
except it goes through a set() instead of get().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: dsa: mv88e6xxx: fix IPv6

We have had some emails in private over this issue, this is my current
patch set rebased on top of net-next which provides working IPv6 (and
probably other protocols as well) over mv88e6xxx DSA switches.

The problem comes down to mv88e6xxx defaulting to not flood unknown
unicast and multicast datagrams, as they would be by dumb switches,
and as the Linux bridge code does by default.

There is also the issue of IPv6 over a vlan that is transparent to the
bridge; the multicast querier will not reach inside the vlan, and so
the switch can not learn about multicast routing within the vlan.

These flood settings can be disabled via the Linux bridge code if it's
desired to make the switch behave more like a managed switch, eg, by
enabling the multicast querier.  However, the multicast querier
defaults to being disabled which effectively means that by default,
mv88e6xxx switches block all multicast traffic.  This is at odds with
the Linux bridge documentation, and the defaults that the Linux bridge
code adopts.

So, this patch set adds DSA support for Linux bridge flags, adds
mv88e6xxx support for the unicast and multicast flooding flags, and
lastly enables flooding of these frames by default to match the
Linux bridge defaults.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Switches work by learning the MAC address for each attached station by
monitoring traffic from each station.  When a station sends a packet,
the switch records which port the MAC address is connected to.

With IPv4 networking, before communication commences with a neighbour,
an ARP packet is broadcasted to all stations asking for the MAC address
corresponding with the IPv4.  The desired station responds with an ARP
reply, and the ARP reply causes the switch to learn which port the
station is connected to.

With IPv6 networking, the situation is rather different.  Rather than
broadcasting ARP packets, a "neighbour solicitation" is multicasted
rather than broadcasted.  This multicast needs to reach the intended
station in order for the neighbour to be discovered.

Once a neighbour has been discovered, and entered into the sending
stations neighbour cache, communication can restart at a point later
without sending a new neighbour solicitation, even if the entry in
the neighbour cache is marked as stale.  This can be after the MAC
address has expired from the forwarding cache of the DSA switch -
when that occurs, there is a long pause in communication.

Our DSA implementation for mv88e6xxx switches disables flooding of
multicast and unicast frames for bridged ports.  As per the above
description, this is fine for IPv4 networking, since the broadcasted
ARP queries will be sent to and received by all stations on the same
network.  However, this breaks IPv6 very badly - blocking neighbour
solicitations and later causing connections to stall.

The defaults that the Linux bridge code expect from bridges are for
unknown unicast and unknown multicast frames to be flooded to all ports
on the bridge, which is at odds to the defaults adopted by our DSA
implementation for mv88e6xxx switches.

This commit enables by default flooding of both unknown unicast and
unknown multicast frames whenever a port is added to a bridge, and
disables the flooding when a port leaves the bridge.  This means that
mv88e6xxx DSA switches now behave as per the bridge(8) man page, and
IPv6 works flawlessly through such a switch.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for the bridge flags to Marvell 88e6xxx bridges, allowing
the multicast and unicast flood properties to be controlled.  These
can be controlled on a per-port basis via commands such as:

	bridge link set dev lan1 flood on|off
	bridge link set dev lan1 mcast_flood on|off
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Linux bridge implementation allows various properties of the bridge
to be controlled, such as flooding unknown unicast and multicast frames.
This patch adds the necessary DSA infrastructure to allow the Linux
bridge support to control these properties for DSA switches.
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[florian: Add missing dp and ds variables declaration to fix build]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

br_ip4_multicast_mrd_rcv only return 0 and -ENOMSG,
no other negative value
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This case block has been terminated by a return, so not need
a switch fall-through
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The error code isn't set on this path so it would result in returning
ERR_PTR(0) and a NULL dereference in the caller.

Fixes: 18d3eefb ("net: sched: refactor tcf_block_find() into standalone functions")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are spelling mistakes in warning macro messages. Fix them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the only way to clear the forwarding cache was to delete the
entries one by one using the MRT_DEL_MFC socket option or to destroy and
recreate the socket.

Create a new socket option which with the use of optional flags can
clear any combination of multicast entries (static or not static) and
multicast vifs (static or not static).

Calling the new socket option MRT_FLUSH with the flags MRT_FLUSH_MFC and
MRT_FLUSH_VIFS will clear all entries and vifs on the socket except for
static entries.
Signed-off-by: Callum Sinclair <callum.sinclair@alliedtelesis.co.nz>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: improve generic clause 45 aneg configuration

Improve generic clause 45 aneg configuration.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use new function genphy_c45_check_and_restart_aneg() to reduce
boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function will be used by config_aneg callback implementations of
PHY drivers and allows to reduce boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Like in genphy_config_aneg() for clause 22 PHY's, we should keep modes
from being advertised that are known to be broken with EEE.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We want to use this function in phy-c45.c too, therefore export it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: improve genphy_read_status

Series includes two smaller improvements to genphy_read_status.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If link partner and we can't agree on any mode, then it doesn't make
sense to pretend we would have agreed on 10/half. Therefore set a
proper default.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After recent changes to genphy_read_status() this orphaned register
read remained as leftover. So remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Read port count from the shared memory instead of driver deriving this
value. This change simplifies the driver implementation and also avoids
any dependencies for finding the port-count.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eran Ben Elisha says:

====================
Devlink health fixes series

This series includes two small fixes from Aya for the devlink health
infrastructure introduced earlier in this window.

First patch rename some UAPI attributes to better reflect their use.
Second patch reduces the amount of data passed from the devlink to the
netlink layer upon get reporter command, in case of no-recovery reporter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid sending attributes related to recovery:
DEVLINK_ATTR_HEALTH_REPORTER_GRACEFUL_PERIOD and
DEVLINK_ATTR_HEALTH_REPORTER_AUTO_RECOVER in reply to
DEVLINK_CMD_HEALTH_REPORTER_GET for a reporter which didn't register a
recover operation.
These parameters can't be configured on a reporter that did not provide
a recover operation, thus not needed to return them.

Fixes: 7afe335a ("devlink: Add health get command")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename devlink health attributes for better reflect the attributes use.
Add COUNT prefix on error counter attribute and recovery counter
attribute.

Fixes: 7afe335a ("devlink: Add health get command")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ursula Braun says:

====================
net/smc: patches 2019-02-21

here are patches for SMC:
* patch 1 is a cleanup without functional change
* patches 2-6 enhance SMC pnetid support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

SMC-D devices are identified by their PCI IDs in the pnet table. In
order to make usage of the pnet table more consistent for users, this
patch adds this form of identification for ib devices as well.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds namespace support to the pnet table code. Each network
namespace gets its own pnet table. Infiniband and smcd device pnetids
can only be modified in the initial namespace. In other namespaces they
can still be used as if they were set by the underlying hardware.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, users can only set pnetids for netdevs and ib devices in the
pnet table. This patch adds support for smcd devices to the pnet table.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a device does not have a pnetid, users can set a temporary pnetid for
said device in the pnet table. This patch reworks the pnet table to make
it more flexible. Multiple entries with the same pnetid but differing
devices are now allowed. Additionally, the netlink interface now sends
each mapping from pnetid to device separately to the user while
maintaining the message format existing applications might expect. Also,
the SMC data structure for ib devices already has a pnetid attribute.
So, it is used to store the user defined pnetids. As a result, the pnet
table entries are only used for netdevs.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pnetids are retrieved from the underlying hardware as EBCDIC. This patch
converts pnetids to ASCII.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use local variable pflags from the beginning of function
smcr_tx_sndbuf_nonempty
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>