kfree_skb() shall be used instead of kfree(). Fix it.

Fixes: 091810db ("net: stmmac: Introduce selftests support")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Variable shall be __be16. Fix it.

Fixes: 091810db ("net: stmmac: Introduce selftests support")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The smp_store_release call in fqdir_exit cannot protect the setting
of fqdir->dead as claimed because its memory barrier is only
guaranteed to be one-way and the barrier precedes the setting of
fqdir->dead.

IOW it doesn't provide any barriers between fq->dir and the following
hash table destruction.

In fact, the code is safe anyway because call_rcu does provide both
the memory barrier as well as a guarantee that when the destruction
work starts executing all RCU readers will see the updated value for
fqdir->dead.

Therefore this patch removes the unnecessary smp_store_release call
as well as the corresponding READ_ONCE on the read-side in order to
not confuse future readers of this code.  Comments have been added
in their places.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix smatch warning:

drivers/net/ethernet/marvell/mvpp2/mvpp2_cls.c:1236
 mvpp2_ethtool_cls_rule_ins() warn: unsigned 'info->fs.location' is never less than zero.

'info->fs.location' is u32 type, never less than zero.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make use of devm_alloc_etherdev_mqs() to simplify the code.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename _P to _P_VAL and _R to _R_VAL to avoid global
namespace conflicts:

drivers/media/dvb-frontends/tua6100.c: In function ‘tua6100_set_params’:
drivers/media/dvb-frontends/tua6100.c:79: warning: "_P" redefined
 #define _P 32

In file included from ./include/acpi/platform/aclinux.h:54,
                 from ./include/acpi/platform/acenv.h:152,
                 from ./include/acpi/acpi.h:22,
                 from ./include/linux/acpi.h:34,
                 from ./include/linux/i2c.h:17,
                 from drivers/media/dvb-frontends/tua6100.h:30,
                 from drivers/media/dvb-frontends/tua6100.c:32:
./include/linux/ctype.h:14: note: this is the location of the previous definition
 #define _P 0x10 /* punct */
Signed-off-by: David S. Miller <davem@davemloft.net>

Ruslan Babayev says:

====================
Enable SFP on ACPI based systems

Changes:
v2:
	- more descriptive commit body
v3:
	- made 'i2c_acpi_find_adapter_by_handle' static inline
v4:
	- don't initialize i2c_adapter to NULL. Instead see below...
	- handle the case of neither DT nor ACPI present as invalid.
	- alphabetical includes.
	- use has_acpi_companion().
	- use the same argument name in i2c_acpi_find_adapter_by_handle()
	  in both stubbed and non-stubbed cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Lookup I2C adapter using the "i2c-bus" device property on ACPI based
systems similar to how it's done with DT.

An example DSD describing an SFP on an ACPI based system:

Device (SFP0)
{
    Name (_HID, "PRP0001")
    Name (_CRS, ResourceTemplate()
    {
        GpioIo(Exclusive, PullDefault, 0, 0, IoRestrictionNone,
               "\\_SB.PCI0.RP01.GPIO", 0, ResourceConsumer)
            { 0, 1, 2, 3, 4 }
    })
    Name (_DSD, Package ()
    {
        ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
        Package () {
            Package () { "compatible", "sff,sfp" },
            Package () { "i2c-bus", \_SB.PCI0.RP01.I2C.MUX.CH0 },
            Package () { "maximum-power-milliwatt", 1000 },
            Package () { "tx-disable-gpios", Package () { ^SFP0, 0, 0, 1} },
            Package () { "reset-gpio",       Package () { ^SFP0, 0, 1, 1} },
            Package () { "mod-def0-gpios",   Package () { ^SFP0, 0, 2, 1} },
            Package () { "tx-fault-gpios",   Package () { ^SFP0, 0, 3, 0} },
            Package () { "los-gpios",        Package () { ^SFP0, 0, 4, 1} },
        },
    })
}

Device (PHY0)
{
    Name (_HID, "PRP0001")
    Name (_DSD, Package ()
    {
        ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
        Package () {
            Package () { "compatible", "ethernet-phy-ieee802.3-c45" },
            Package () { "sfp", \_SB.PCI0.RP01.SFP0 },
            Package () { "managed", "in-band-status" },
            Package () { "phy-mode", "sgmii" },
        },
    })
}
Signed-off-by: Ruslan Babayev <ruslan@babayev.com>
Cc: xe-linux-external@cisco.com
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This allows drivers to lookup i2c adapters on ACPI based systems similar to
of_get_i2c_adapter_by_node() with DT based systems.
Signed-off-by: Ruslan Babayev <ruslan@babayev.com>
Cc: xe-linux-external@cisco.com
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: linux-hwmon@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's found while review and probably never happens, but real number
of queues is set per device, and error path should be per device.
So split error path based on usage_count.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ioana Ciornei says:

====================
Decoupling PHYLINK from struct net_device

Following two separate discussion threads in:
  https://www.spinics.net/lists/netdev/msg569087.html
and:
  https://www.spinics.net/lists/netdev/msg570450.html

Previous RFC patch set: https://www.spinics.net/lists/netdev/msg571995.html

PHYLINK was reworked in order to accept multiple operation types,
PHYLINK_NETDEV and PHYLINK_DEV, passed through a phylink_config
structure alongside the corresponding struct device.

One of the main concerns expressed in the RFC was that using notifiers
to signal the corresponding phylink_mac_ops would break PHYLINK's API
unity and that it would become harder to grep for its users.
Using the current approach, we maintain a common API for all users.
Also, printing useful information in PHYLINK, when decoupled from a
net_device, is achieved using dev_err&co on the struct device received
(in DSA's case is the device corresponding to the dsa_switch).

PHYLIB (which PHYLINK uses) was reworked to the extent that it does not
crash when connecting to a PHY and the net_device pointer is NULL.

Lastly, DSA has been reworked in its way that it handles PHYs for ports
that lack a net_device (CPU and DSA ports).  For these, it was
previously using PHYLIB and is now using the PHYLINK_DEV operation type.
Previously, a driver that wanted to support PHY operations on CPU/DSA
ports has to implement .adjust_link(). This patch set not only gives
drivers the options to use PHYLINK uniformly but also urges them to
convert to it. For compatibility, the old code is kept but it will be
removed once all drivers switch over.

The patchset was tested on the NXP LS1021A-TSN board having the
following Ethernet layout:
  https://lkml.org/lkml/2019/5/5/279
The CPU port was moved from the internal RGMII fixed-link (enet2 ->
switch port 4) to an external loopback Cat5 cable between the enet1 port
and the front-facing swp2 SJA1105 port. In this mode, both the master
and the CPU port have an attached PHY which detects link change events:

[   49.105426] fsl-gianfar soc:ethernet@2d50000 eth1: Link is Down
[   50.305486] sja1105 spi0.1: Link is Down
[   53.265596] fsl-gianfar soc:ethernet@2d50000 eth1: Link is Up - 1Gbps/Full - flow control off
[   54.466304] sja1105 spi0.1: Link is Up - 1Gbps/Full - flow control off

Changes in v2:
  - fixed sparse warnings
  - updated 'Documentation/ABI/testing/sysfs-class-net-phydev'
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

PHYLIB and PHYLINK handle fixed-link interfaces differently. PHYLIB
wraps them in a software PHY ("pseudo fixed link") phydev construct such
that .adjust_link driver callbacks see an unified API. Whereas PHYLINK
simply creates a phylink_link_state structure and passes it to
.mac_config.

At the time the driver was introduced, DSA was using PHYLIB for the
CPU/cascade ports (the ones with no net devices) and PHYLINK for
everything else.

As explained below:

commit aab9c406
Author: Florian Fainelli <f.fainelli@gmail.com>
Date:   Thu May 10 13:17:36 2018 -0700

  net: dsa: Plug in PHYLINK support

  Drivers that utilize fixed links for user-facing ports (e.g: bcm_sf2)
  will need to implement phylink_mac_ops from now on to preserve
  functionality, since PHYLINK *does not* create a phy_device instance
  for fixed links.

In the above patch, DSA guards the .phylink_mac_config callback against
a NULL phydev pointer.  Therefore, .adjust_link is not called in case of
a fixed-link user port.

This patch fixes the situation by converting the driver from using
.adjust_link to .phylink_mac_config.  This can be done now in a unified
fashion for both slave and CPU/cascade ports because DSA now uses
PHYLINK for all ports.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For DSA switches that do not have an .adjust_link callback, aka those
who transitioned totally to the PHYLINK-compliant API, use PHYLINK to
drive the CPU/DSA ports.

The PHYLIB usage and .adjust_link are kept but deprecated, and users are
asked to transition from it.  The reason why we can't do anything for
them is because PHYLINK does not wrap the fixed-link state behind a
phydev object, so we cannot wrap .phylink_mac_config into .adjust_link
unless we fabricate a phy_device structure.

For these ports, the newly introduced PHYLINK_DEV operation type is
used and the dsa_switch device structure is passed to PHYLINK for
printing purposes.  The handling of the PHYLINK_NETDEV and PHYLINK_DEV
PHYLINK instances is common from the perspective of the driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to have a common handling of PHYLINK for the slave and non-user
ports, the DSA core glue logic (between PHYLINK and the driver) must use
an API that does not rely on a struct net_device.

These will also be called by the CPU-port-handling code in a further
patch.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the latest addition to the PHYLINK infrastructure, we are faced
with a decision on when to print necessary info using the struct
net_device and when with the struct device.

Add a series of macros that encapsulate this decision and replace all
uses of netdev_err&co with phylink_err.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the PHYLINK_DEV operation type, the PHYLINK infrastructure can work
without an attached net_device. For printing usecases, instead, a struct
device * should be passed to PHYLINK using the phylink_config structure.

Also, netif_carrier_* calls ar guarded by the presence of a valid
net_device. When using the PHYLINK_DEV operation type, we cannot check
link status using the netif_carrier_ok() API so instead, keep an
internal state of the MAC and call mac_link_{down,up} only when the link
changed.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The phylink_config structure will encapsulate a pointer to a struct
device and the operation type requested for this instance of PHYLINK.
This patch does not make any functional changes, it just transitions the
PHYLINK internals and all its users to the new API.

A pointer to a phylink_config structure will be passed to
phylink_create() instead of the net_device directly. Also, the same
phylink_config pointer will be passed back to all phylink_mac_ops
callbacks instead of the net_device. Using this mechanism, a PHYLINK
user can get the original net_device using a structure such as
'to_net_dev(config->dev)' or directly the structure containing the
phylink_config using a container_of call.

At the moment, only the PHYLINK_NETDEV is defined as a valid operation
type for PHYLINK. In this mode, a valid reference to a struct device
linked to the original net_device should be passed to PHYLINK through
the phylink_config structure.

This API changes is mainly driven by the necessity of adding a new
operation type in PHYLINK that disconnects the phy_device from the
net_device and also works when the net_device is lacking.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a cosmetic patch that reduces the clutter in phylink_resolve
around calling the .mac_link_up/.mac_link_down driver callbacks.  In a
further patch this logic will be extended to emit notifications in case
a net device does not exist.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Export a phy_standalone device attribute that is meant to give the
indication that this PHY lacks an attached_dev and its corresponding
sysfs link. The attribute will be created only when the
phy_attach_direct() function will be called with a NULL net_device.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In general, we don't want MAC drivers calling phy_attach_direct with the
net_device being NULL. Add checks against this in all the functions
calling it: phy_attach() and phy_connect_direct().
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A prerequisite for PHYLIB to work in the absence of a struct net_device
is to not access pointers to it.

Changes are needed in the following areas:

 - Printing: In some places netdev_err was replaced with phydev_err.

 - Incrementing reference count to the parent MDIO bus driver: If there
   is no net device, then the reference count should definitely be
   incremented since there is no chance that it was an Ethernet driver
   who registered the MDIO bus.

 - Sysfs links are not created in case there is no attached_dev.

 - No netif_carrier_off is done if there is no attached_dev.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a cosmetic patch that wraps the operation of creating sysfs
links between the netdev->phydev and the phydev->attached_dev.

This is needed to keep the indentation level in check in a follow-up
patch where this function will be guarded against the existence of a
phydev->attached_dev.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ctinfo is a new tc filter action module.  It is designed to restore
information contained in firewall conntrack marks to other packet fields
and is typically used on packet ingress paths.  At present it has two
independent sub-functions or operating modes, DSCP restoration mode &
skb mark restoration mode.

The DSCP restore mode:

This mode copies DSCP values that have been placed in the firewall
conntrack mark back into the IPv4/v6 diffserv fields of relevant
packets.

The DSCP restoration is intended for use and has been found useful for
restoring ingress classifications based on egress classifications across
links that bleach or otherwise change DSCP, typically home ISP Internet
links.  Restoring DSCP on ingress on the WAN link allows qdiscs such as
but by no means limited to CAKE to shape inbound packets according to
policies that are easier to set & mark on egress.

Ingress classification is traditionally a challenging task since
iptables rules haven't yet run and tc filter/eBPF programs are pre-NAT
lookups, hence are unable to see internal IPv4 addresses as used on the
typical home masquerading gateway.  Thus marking the connection in some
manner on egress for later restoration of classification on ingress is
easier to implement.

Parameters related to DSCP restore mode:

dscpmask - a 32 bit mask of 6 contiguous bits and indicate bits of the
conntrack mark field contain the DSCP value to be restored.

statemask - a 32 bit mask of (usually) 1 bit length, outside the area
specified by dscpmask.  This represents a conditional operation flag
whereby the DSCP is only restored if the flag is set.  This is useful to
implement a 'one shot' iptables based classification where the
'complicated' iptables rules are only run once to classify the
connection on initial (egress) packet and subsequent packets are all
marked/restored with the same DSCP.  A mask of zero disables the
conditional behaviour ie. the conntrack mark DSCP bits are always
restored to the ip diffserv field (assuming the conntrack entry is found
& the skb is an ipv4/ipv6 type)

e.g. dscpmask 0xfc000000 statemask 0x01000000

|----0xFC----conntrack mark----000000---|
| Bits 31-26 | bit 25 | bit24 |~~~ Bit 0|
| DSCP       | unused | flag  |unused   |
|-----------------------0x01---000000---|
      |                   |
      |                   |
      ---|             Conditional flag
         v             only restore if set
|-ip diffserv-|
| 6 bits      |
|-------------|

The skb mark restore mode (cpmark):

This mode copies the firewall conntrack mark to the skb's mark field.
It is completely the functional equivalent of the existing act_connmark
action with the additional feature of being able to apply a mask to the
restored value.

Parameters related to skb mark restore mode:

mask - a 32 bit mask applied to the firewall conntrack mark to mask out
bits unwanted for restoration.  This can be useful where the conntrack
mark is being used for different purposes by different applications.  If
not specified and by default the whole mark field is copied (i.e.
default mask of 0xffffffff)

e.g. mask 0x00ffffff to mask out the top 8 bits being used by the
aforementioned DSCP restore mode.

|----0x00----conntrack mark----ffffff---|
| Bits 31-24 |                          |
| DSCP & flag|      some value here     |
|---------------------------------------|
			|
			|
			v
|------------skb mark-------------------|
|            |                          |
|  zeroed    |                          |
|---------------------------------------|

Overall parameters:

zone - conntrack zone

control - action related control (reclassify | pipe | drop | continue |
ok | goto chain <CHAIN_INDEX>)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MAC on the GBit versions supports 1000/Full only, however the PHY
partially claims to support 1000/Half. So let's explicitly remove
this mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hardware offload of matchall classifier and police action are now
supported via the tc command.
Supported police parameters are: rate and burst.

Example:

Add:
tc qdisc add dev eth3 handle ffff: ingress
tc filter add dev eth3 parent ffff: prio 1 handle 2	\
	matchall skip_sw				\
	action police rate 100Mbit burst 10000

Show:
tc -s -d qdisc show dev eth3
tc -s -d filter show dev eth3 ingress

Delete:
tc filter del dev eth3 parent ffff: prio 1
tc qdisc del dev eth3 handle ffff: ingress
Signed-off-by: Joergen Andreasen <joergen.andreasen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2019-05-29

This series contains updates to ice driver only.

Bruce cleans up white space issues and fixes complaints about using
bitop assignments using operands of different sizes.

Anirudh cleans up code that is no longer needed now that the firmware
supports the functionality.  Adds support for ethtool selftestto the ice
driver, which includes testing link, interrupts, eeprom, registers and
packet loopback.  Also, cleaned up duplicate code.

Tony implements support for toggling receive VLAN filter via ethtool.

Brett bumps up the minimum receive descriptor count per queue to resolve
dropped packets.  Refactored the interrupt tracking for the ice driver
to resolve issues seen with the co-existence of features and SR-IOV, so
instead of having a hardware IRQ tracker and a software IRQ tracker,
simply use one tracker.  Also adds a helper function to trigger software
interrupts.

Mitch changes how Malicious Driver Detection (MDD) events are handled,
to ensure all VFs checked for MDD events and just log the event instead
of disabling the VF, which was preventing proper release of resources if
the VF is rebooted or the VF driver reloaded.

Dave cleans up a redundant call to register LLDP MIB change events.

Dan adds support to retrieve the current setting of firmware logging
from the hardware to properly initialize the hardware structure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix gcc build error while CONFIG_INET is not set

drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.o: In function `__stmmac_test_loopback':
stmmac_selftests.c:(.text+0x8ec): undefined reference to `ip_send_check'
stmmac_selftests.c:(.text+0xacc): undefined reference to `udp4_hwcsum'

Add CONFIG_INET dependency to fix this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 091810db ("net: stmmac: Introduce selftests support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves common code between rht_ptr and rht_ptr_exclusive
into __rht_ptr.  It also adds a new helper rht_ptr_rcu exclusively
for the RCU case.  This way rht_ptr becomes a lock-only construct
so we can use the lighter rcu_dereference_protected primitive.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before the netdev is registered, calling netdev_info() will emit
something as "(unnamed net device) (uninitialized)", looks confusing.

Before this patch:
[    3.155028] stmmaceth f7b60000.ethernet (unnamed net_device) (uninitialized): device MAC address 52:1a:55:18:9e:9d

After this patch:
[    3.155028] stmmaceth f7b60000.ethernet: device MAC address 52:1a:55:18:9e:9d
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a spelling mistake in a DP_INFO message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new function ice_trigger_sw_intr to trigger interrupts.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Call ice_vsi_cfg_rss_lut_key only if RSS is enabled.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In order to initialize the current status of the FW logging,
this patch adds ice_get_fw_log_cfg. The function retrieves
the current setting of the FW logging from HW and updates the
ice_hw structure accordingly.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove duplicate define for ICE_INVAL_Q_HANDLE. Move defines to the
top of the file.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In the path for re-enabling FW LLDP engine, there is
a call to register for LLDP MIB change events.  This
call is redundant, in that the call to ice_pf_dcb_cfg
will already register the driver for these events.  Also,
the call as it stands now is too early in the flow before
before DCB is configured.

Remove the redundant call.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Change the message level of the MTU change log message from debug to
info.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Don't use the mdd_detected variable as an exit condition for this loop;
the first VF to NOT have an MDD event will cause the loop to terminate.

Instead just look at all of the VFs, but don't disable them. This
prevents proper release of resources if the VFs are rebooted or the VF
driver reloaded. Instead, just log a message and call out repeat
offenders.

To make it clear what we are doing, use a differently-named variable in
the loop.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we have two MSI-x (IRQ) trackers, one for OS requested MSI-x
entries (sw_irq_tracker) and one for hardware MSI-x vectors
(hw_irq_tracker). Generally the sw_irq_tracker has less entries than the
hw_irq_tracker because the hw_irq_tracker has entries equal to the max
allowed MSI-x per PF and the sw_irq_tracker is mainly the minimum (non
SR-IOV portion of the vectors, kernel granted IRQs). All of the non
SR-IOV portions of the driver (i.e. LAN queues, RDMA queues, OICR, etc.)
take at least one of each type of tracker resource. SR-IOV only grabs
entries from the hw_irq_tracker. There are a few issues with this approach
that can be seen when doing any kind of device reconfiguration (i.e.
ethtool -L, SR-IOV, etc.). One of them being, any time the driver creates
an ice_q_vector and associates it to a LAN queue pair it will grab and
use one entry from the hw_irq_tracker and one from the sw_irq_tracker.
If the indices on these does not match it will cause a Tx timeout, which
will cause a reset and then the indices will match up again and traffic
will resume. The mismatched indices come from the trackers not being the
same size and/or the search_hint in the two trackers not being equal.
Another reason for the refactor is the co-existence of features with
SR-IOV. If SR-IOV is enabled and the interrupts are taken from the end
of the sw_irq_tracker then other features can no longer use this space
because the hardware has now given the remaining interrupts to SR-IOV.

This patch reworks how we track MSI-x vectors by removing the
hw_irq_tracker completely and instead MSI-x resources needed for SR-IOV
are determined all at once instead of per VF. This can be done because
when creating VFs we know how many are wanted and how many MSI-x vectors
each VF needs. This also allows us to start using MSI-x resources from
the end of the PF's allowed MSI-x vectors so we are less likely to use
entries needed for other features (i.e. RDMA, L2 Offload, etc).

This patch also reworks the ice_res_tracker structure by removing the
search_hint and adding a new member - "end". Instead of having a
search_hint we will always search from 0. The new member, "end", will be
used to manipulate the end of the ice_res_tracker (specifically
sw_irq_tracker) during runtime based on MSI-x vectors needed by SR-IOV.
In the normal case, the end of ice_res_tracker will be equal to the
ice_res_tracker's num_entries.

The sriov_base_vector member was added to the PF structure. It is used
to represent the starting MSI-x index of all the needed MSI-x vectors
for all SR-IOV VFs. Depending on how many MSI-x are needed, SR-IOV may
have to take resources from the sw_irq_tracker. This is done by setting
the sw_irq_tracker->end equal to the pf->sriov_base_vector. When all
SR-IOV VFs are removed then the sw_irq_tracker->end is reset back to
sw_irq_tracker->num_entries. The sriov_base_vector, along with the VF's
number of MSI-x (pf->num_vf_msix), vf_id, and the base MSI-x index on
the PF (pf->hw.func_caps.common_cap.msix_vector_first_id), is used to
calculate the first HW absolute MSI-x index for each VF, which is used
to write to the VPINT_ALLOC[_PCI] and GLINT_VECT2FUNC registers to
program the VFs MSI-x PCI configuration bits. Also, the sriov_base_vector
is used along with VF's num_vf_msix, vf_id, and q_vector->v_idx to
determine the MSI-x register index (used for writing to GLINT_DYN_CTL)
within the PF's space.

Interrupt changes removed any references to hw_base_vector, hw_oicr_idx,
and hw_irq_tracker. Only sw_base_vector, sw_oicr_idx, and sw_irq_tracker
variables remain. Change all of these by removing the "sw_" prefix to
help avoid confusion with these variables and their use.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a handler for ethtool selftest. Selftest includes
testing link, interrupts, eeprom, registers and packet loopback.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>