Add a devicetree binding documentation for the mt7621 gpio.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

For easy grepping on debug purposes join string literals back in the
messages.

While here, fix couple of small indentation issues.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

On the Aspeed chip, the GPIOs can be under control of the ARM
chip or of the ColdFire coprocessor. (There's a third command
source, the LPC bus, which we don't use or support yet).

The control of which master is allowed to modify a given
GPIO is per-bank (8 GPIOs).

Unfortunately, systems already exist for which we want to
use GPIOs of both sources in the same bank.

This provides an API exported by the gpio-aspeed driver
that an aspeed coprocessor driver can use to "grab" some
GPIOs for use by the coprocessor, and allow the coprocessor
driver to provide callbacks for arbitrating access.

Once at least one GPIO of a given bank has been "grabbed"
by the coprocessor, the entire bank is marked as being
under coprocessor control. It's command source is switched
to the coprocessor.

If the ARM then tries to write to a GPIO in such a marked bank,
the provided callbacks are used to request access from the
coprocessor driver, which is responsible to doing whatever
is necessary to "pause" the coprocessor or prevent it from
trying to use the GPIOs while the ARM is doing its accesses.

During that time, the command source for the bank is temporarily
switched back to the ARM.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds the definitions for the command source registers
and a helper to set them.

Those registers allow to control which bus master on the
SoC is allowed to modify a given bank of GPIOs and will
be used by subsequent patches.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Aspeed GPIO hardware has a quirk: the value register, for an
output GPIO, doesn't contain the last value written (the write
latch content) but the sampled input value.

This means that when reading back shortly after writing, you can
get an incorrect value as the input value is delayed by a few
synchronizers.

The HW supports a separate read-only register "Data Read Register"
which allows you to read the write latch instead.

This adds the definition for it, and uses it for the initial
population of the GPIO value cache. It will be used more in
subsequent patches.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Use a single accessor function for all register types instead
of several spread around. This will make it easier/cleaner
to introduce new registers and keep the mechanism in one
place.

The big switch/case is optimized at compile time since the
switch value is a constant.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Don't warn about missing interrupts support when the parent interrupt is
not defined. Enabling interrupts support would not make it work anyway.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This is a GPIO driver, include only <linux/gpio/driver.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This is a GPIO driver, include only <linux/gpio/driver.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This is a GPIO driver, include only <linux/gpio/driver.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

I don't like the __namespace and this is simple enough to just
inline at all sites.

Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Acked-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This removes the custom implementation of the BIT() macro
and inlines all calls to the helper.

Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Acked-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This is a GPIO driver, include only <linux/gpio/driver.h>.

Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Acked-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This is a GPIO driver, include only <linux/gpio/driver.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This purely syntactic change switches unsigned char to
u8 in the driver.

Cc: Bruno Randolf <br1@einfach.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The chip has a bit for controlling open drain, and it is
easy to implement the callback to support open drain when
needed, so let's implement it.

Cc: Bruno Randolf <br1@einfach.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Bit 0 in the config register obviously controls the direction
of the GPIO so instead of hammering 0x0/0x1 into that register,
use read-modify-write so that we can also alter the other bits
in the register.

Cc: Bruno Randolf <br1@einfach.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

It's pretty simple to implement the .get_direction() for this
chip, so let's just do it.

Cc: Bruno Randolf <br1@einfach.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This is a GPIO driver, include only <linux/gpio/driver.h>.

Cc: Bruno Randolf <br1@einfach.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

It's pretty simple to implement the .get_direction() for this
chip, so let's just do it.

Cc: Denis Turischev <denis.turischev@compulab.co.il>
Cc: Daniel Krueger <daniel.krueger@systec-electronic.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This is a GPIO driver, include only <linux/gpio/driver.h>.

Cc: Denis Turischev <denis.turischev@compulab.co.il>
Cc: Daniel Krueger <daniel.krueger@systec-electronic.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This is a GPIO driver, include only <linux/gpio/driver.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This is a GPIO driver, include only <linux/gpio/driver.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This is a GPIO driver, include only <linux/gpio/driver.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This is a GPIO driver, include only <linux/gpio/driver.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add an implementation to get the current GPIO state.

The callback is used by the leds-gpio driver for example, in case the
current LED/GPIO state should be kept during driver load.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add support for the Tegra194 GPIO bank configuration.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Tegra194 GPIO controller is similar to the one in Tegra186.
Add relevant information to the device tree binding documentation.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.

Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The GPIO (descriptor) API registers a "label" naming what is
currently using the GPIO line. Typically this is taken from
things like the device tree node, so "reset-gpios" will result
in he line being labeled "reset".

The technical effect is pretty much zero: the use is for
debug and introspection, such as "lsgpio" and debugfs files.

However sometimes the user want this cuddly feeling of
listing all GPIO lines and seeing exactly what they are for
and it gives a very fulfilling sense of control. Especially
in the cases when the device tree node doesn't provide a
good name, or anonymous GPIO lines assigned just to
"gpios" in the device tree because the usage is implicit.

For these cases it may be nice to be able to label the
line directly and explicitly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

When i2c_new_dummy fails, the lack of error-handling code may
cause unexpected results.

This patch adds error-handling code after calling i2c_new_dummy.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Currently the driver assumes that the interrupts are continuous
and does platform_get_irq only once and assumes the rest are continuous,
instead call platform_get_irq for all the interrupts and store them
in an array for later use.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This is needed in case of PROBE_DEFER if IRQ resource is not yet ready.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Renesas R-Car V3H (R8A77980) SoC also has the R-Car gen3 compatible GPIO
controllers, so document the SoC specific bindings.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

men_z127_debounce() tries to round up and down, but uses functions which
are only suitable when the divider is a power of two, which is not the
case. Use the appropriate ones.

Found by static check. Compile tested.

Fixes: f436bc27 ("gpio: add driver for MEN 16Z127 GPIO controller")
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull block fixes from Jens Axboe:
 "A collection of fixes that should go into -rc1. This contains:

   - bsg_open vs bsg_unregister race fix (Anatoliy)

   - NVMe pull request from Christoph, with fixes for regressions in
     this window, FC connect/reconnect path code unification, and a
     trace point addition.

   - timeout fix (Christoph)

   - remove a few unused functions (Christoph)

   - blk-mq tag_set reinit fix (Roman)"

* tag 'for-linus-20180616' of git://git.kernel.dk/linux-block:
  bsg: fix race of bsg_open and bsg_unregister
  block: remov blk_queue_invalidate_tags
  nvme-fabrics: fix and refine state checks in __nvmf_check_ready
  nvme-fabrics: handle the admin-only case properly in nvmf_check_ready
  nvme-fabrics: refactor queue ready check
  blk-mq: remove blk_mq_tagset_iter
  nvme: remove nvme_reinit_tagset
  nvme-fc: fix nulling of queue data on reconnect
  nvme-fc: remove reinit_request routine
  blk-mq: don't time out requests again that are in the timeout handler
  nvme-fc: change controllers first connect to use reconnect path
  nvme: don't rely on the changed namespace list log
  nvmet: free smart-log buffer after use
  nvme-rdma: fix error flow during mapping request data
  nvme: add bio remapping tracepoint
  nvme: fix NULL pointer dereference in nvme_init_subsystem
  blk-mq: reinit q->tag_set_list entry only after grace period

Pull documentation fixes from Mauro Carvalho Chehab:
 "This solves a series of broken links for files under Documentation,
  and improves a script meant to detect such broken links (see
  scripts/documentation-file-ref-check).

  The changes on this series are:

   - can.rst: fix a footnote reference;

   - crypto_engine.rst: Fix two parsing warnings;

   - Fix a lot of broken references to Documentation/*;

   - improve the scripts/documentation-file-ref-check script, in order
     to help detecting/fixing broken references, preventing
     false-positives.

  After this patch series, only 33 broken references to doc files are
  detected by scripts/documentation-file-ref-check"

* tag 'docs-broken-links' of git://linuxtv.org/mchehab/experimental: (26 commits)
  fix a series of Documentation/ broken file name references
  Documentation: rstFlatTable.py: fix a broken reference
  ABI: sysfs-devices-system-cpu: remove a broken reference
  devicetree: fix a series of wrong file references
  devicetree: fix name of pinctrl-bindings.txt
  devicetree: fix some bindings file names
  MAINTAINERS: fix location of DT npcm files
  MAINTAINERS: fix location of some display DT bindings
  kernel-parameters.txt: fix pointers to sound parameters
  bindings: nvmem/zii: Fix location of nvmem.txt
  docs: Fix more broken references
  scripts/documentation-file-ref-check: check tools/*/Documentation
  scripts/documentation-file-ref-check: get rid of false-positives
  scripts/documentation-file-ref-check: hint: dash or underline
  scripts/documentation-file-ref-check: add a fix logic for DT
  scripts/documentation-file-ref-check: accept more wildcards at filenames
  scripts/documentation-file-ref-check: fix help message
  media: max2175: fix location of driver's companion documentation
  media: v4l: fix broken video4linux docs locations
  media: dvb: point to the location of the old README.dvb-usb file
  ...

Pull fsnotify updates from Jan Kara:
 "fsnotify cleanups unifying handling of different watch types.

  This is the shortened fsnotify series from Amir with the last five
  patches pulled out. Amir has modified those patches to not change
  struct inode but obviously it's too late for those to go into this
  merge window"

* tag 'fsnotify_for_v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  fsnotify: add fsnotify_add_inode_mark() wrappers
  fanotify: generalize fanotify_should_send_event()
  fsnotify: generalize send_to_group()
  fsnotify: generalize iteration of marks by object type
  fsnotify: introduce marks iteration helpers
  fsnotify: remove redundant arguments to handle_event()
  fsnotify: use type id to identify connector object type