With this, that 338 can finally become the correct 337500.

Due to the change we need to adjust the intel_dp_aux_ch function to
set the correct value, so adjust the division and also use
DIV_ROUND_CLOSEST instead of the old "round down" behavior because the
spec says the value "should be programmed to get as close as possible
to the ideal rate of 2MHz".

Quoting Paulo's follow-up to a question from Chris Wilson to explain
what exactly will change:

I use the 337500 value on the next patch, when setting the
ips_linetime value. The correct frequency is 337500, not 338000.

ips_linetime = DIV_ROUND_CLOSEST(mode->htotal * 1000 * 8,
intel_ddi_get_cdclk_freq);
For a mode with htotal of 2640 [0] we'll have: (i) (2640 * 1000 * 8) /
338000 = 62.48, resulting in 62 and (ii) (2640 * 1000 * 8) / 337500 =
62.57 resulting in 63.

For the case inside intel_dp.c:
Previously we were using 338. So with the old formula we were writing
338/2 = 169 to the register. And 337500 / 169 = 1997.04 (we use 337500
here because it's the real clock value). With the new value of
337500/2000 we'll have 168.75, which is 168 on the round-down case and
169 on the round-closest case. If we write 168 to the register, 337500
/ 168 = 2008.92, and 2008.92 is more distant from 2000 than 1997.04.
So with this patch we're changing the formula but still writing the
same correct value to the DP AUX register.

[0]: That's 1920x1080@50Hz on my DP monitor.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Pimp the commit message with Paulo's follow-up.]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Move the "*8"  calculation to the left side so we don't propagate
rounding errors. Also use DIV_ROUND_CLOSEST because that's what the
spec says we need to do.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

... instead of mode->crtc_display. The spec says "pipe horizontal
total number of pixels" and the "Haswell Watermark Calculator" tool
uses the "Pipe H Total" instead of "Pipe H Src" as the value.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

The spec says the linetime watermarks must be programmed before
enabling any display low power watermarks, but we're currently
updating the linetime watermarks after we call intel_update_watermarks
(and only at crtc_mode_set, not at crtc_{enable,disable}). So IMHO the
best way guarantee the linetime watermarks will be updated before the
low power watermarks is inside the update_wm function, because it's
the function that enables low power watermarks. And since Haswell is
the only platform that has linetime watermarks, let's completely kill
the "intel_update_linetime_watermarks" abstraction and just use the
intel_update_watermarks abstraction by creating haswell_update_wm.

For now haswell_update_wm is still calling sandybridge_update_wm, but
in the future I plan to implement a function specific to Haswell.

v2: - Rename patch
    - Disable LP watermarks before changing linetime WMs (Chris)
    - Add a comment explaining that this is just temporary code.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

So don't call intel_update_linetime_watermarks from
ironlake_crtc_mode_set. Only Haswell has these watermarks.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

We can use this for fetching encoder specific pipe_config state, like
mode flags, adjusted clock, etc.

Just used for mode flags atm, so we can check the pipe config state at
mode set time.

v2: get_config when checking hw state too
v3: fix DVO and LVDS mode flags (Ville)
    get SDVO DTD for flag fetch (Ville)
v4: use input timings (Ville)
    correct command used (Ville)
    remove gen4 check (Ville)
v5: get DDI flag config too
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v4)
Tested-by: Paulo Zanoni <przanoni@gmail.com> (the new hsw ddi stuff)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Backmerge Linux 3.10-rc2 since the various (rather trivial) conflicts
grew a bit out of hand. intel_dp.c has the only real functional
conflict since the logic changed while dev_priv->edp.bpp was moved
around.

Also squash in a whitespace fixup from Ben Widawsky for
i915_gem_gtt.c, git seems to do something pretty strange in there
(which I don't fully understand tbh).

Conflicts:
	drivers/gpu/drm/i915/i915_reg.h
	drivers/gpu/drm/i915/intel_dp.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Merge tag 'stable/for-linus-3.10-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

Pull Xen fixes from Konrad Rzeszutek Wilk:
 - Regression fix in xen privcmd fixing a memory leak.
 - Add Documentation for tmem driver.
 - Simplify and remove code in the tmem driver.
 - Cleanups.

* tag 'stable/for-linus-3.10-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen: Fixed assignment error in if statement
  xen/xenbus: Fixed over 80 character limit issue
  xen/xenbus: Fixed indentation error in switch case
  xen/tmem: Don't use self[ballooning|shrinking] if frontswap is off.
  xen/tmem: Remove the usage of '[no|]selfballoon' and use 'tmem.selfballooning' bool instead.
  xen/tmem: Remove the usage of 'noselfshrink' and use 'tmem.selfshrink' bool instead.
  xen/tmem: Remove the boot options and fold them in the tmem.X parameters.
  xen/tmem: s/disable_// and change the logic.
  xen/tmem: Fix compile warning.
  xen/tmem: Split out the different module/boot options.
  xen/tmem: Move all of the boot and module parameters to the top of the file.
  xen/tmem: Cleanup. Remove the parts that say temporary.
  xen/privcmd: fix condition in privcmd_close()

This patch add dvo detection for the Chrontel 7010B on some old hardware.

References: https://bugzilla.kernel.org/show_bug.cgi?id=55101
Signed-off-by: Braggle <braggle at free.fr>
[danvet: Fix up whitespace mangling.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Pull hwmon fixes from Guenter Roeck:

 - Error path fixes for abituguru and iio_hwmon drivers.

 - Drop erroneously created attributes from nct6775 driver.

 - Drop redundant safety on cache lifetime for tmp401 driver.

 - Add explicit maintainer for LM95234 and TMP401 drivers.

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  MAINTAINERS: Add myself as maintainer for LM95234 and TMP401 drivers
  hwmon: (tmp401) Drop redundant safety on cache lifetime
  hwmon: fix error return code in abituguru_probe()
  hwmon: (iio_hwmon) Fix null pointer dereference
  hwmon: (nct6775) Do not create non-existing attributes
  hwmon: (iio_hwmon) Fix missing iio_channel_release_all call if devm_kzalloc fail

In commit 78d77df7 ("x86-64, init: Do not set NX bits on non-NX
capable hardware") we added the early_pmd_flags that gets the NX bit set
when a CPU supports NX. However, the new variable was marked __initdata,
because the main _use_ of this is in an __init routine.

However, the bit setting happens from secondary_startup_64(), which is
called not only at bootup, but on every secondary CPU start.  Including
resuming from STR and at CPU hotplug time.  So the value cannot be
__initdata.
Reported-bisected-and-tested-by: Michal Hocko <mhocko@suse.cz>
Cc: stable@vger.kernel.org # v3.9
Acked-by: Peter Anvin <hpa@linux.intel.com>
Cc: Fernando Luis Vázquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fixed assignment error in if statement in balloon.c
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Fixed the format length of the xenbus_backend_ioctl()
function to meet the 80 character limit in
xenbus_dev_backend.c
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Fixed the indentation error in the switch case in
xenbus_dev_backend.c
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Merge tag 'pinctrl-fixes-v3.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pinctrl fixes from Linus Walleij:

 - Three fixes to make the boot path for device tree work properly on
   the Nomadik pin controller.

 - Compile warning fix for the vt8500 driver.

 - Fix error path in pinctrl-single.

 - Free mappings in error path of the Lantiq controller.

 - Documentation fixes.

* tag 'pinctrl-fixes-v3.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl/lantiq: Free mapping configs for both pin and groups
  pinctrl: single: fix error return code in pcs_parse_one_pinctrl_entry()
  pinctrl: generic: Fix typos and clarify comments
  pinctrl: vt8500: Fix incorrect data in WM8750 pinctrl table
  pinctrl: abx500: Rejiggle platform data and DT initialisation
  pinctrl: abx500: Specify failed sub-driver by ID instead of driver_data

Pull kbuild fix from Michal Marek:
 "In an attempt to improve make rpm-pkg, I broke make binrpm-pkg"

* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  package: Makefile: unbreak binrpm-pkg target

I wrote the LM95234 driver and extended the TMP401 driver substantially,
and I have hardware to test both, so it makes sense to explicitly
maintain them.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>

Pull device mapper fix from Alasdair Kergon:
 "A patch to fix metadata resizing with device-mapper thin devices."

* tag 'dm-3.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
  dm thin: fix metadata dev resize detection

Fix detection of the need to resize the dm thin metadata device.

The code incorrectly tried to extend the metadata device when it
didn't need to due to a merging error with patch 24347e95 ("dm thin:
detect metadata device resizing").

  device-mapper: transaction manager: couldn't open metadata space map
  device-mapper: thin metadata: tm_open_with_sm failed
  device-mapper: thin: aborting transaction failed
  device-mapper: thin: switching pool to failure mode
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

time_after (as opposed to time_after_equal) already ensures that the
cache lifetime is at least as much as requested. There is no point in
manually adding another jiffy to that value, and this can confuse the
reader into wrong interpretation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Pull btrfs fixes from Chris Mason:
 "Miao Xie has been very busy, fixing races and enospc problems and many
  other small but important pieces.

  Alexandre Oliva discovered some problems with how our error handling
  was interacting with the block layer and for now has disabled our
  partial handling of sub-page writes.  The real sub-page work is in a
  series of patches from IBM that we still need to integrate and test.
  The code Alexandre has turned off was really incomplete.

  Josef has more error handling fixes and an important fix for the new
  skinny extent format.

  This also has my fix for the tracepoint crash from late in 3.9.  It's
  the first stage in a larger clean up to get rid of btrfs_bio and make
  a proper bioset for all the items we need to tack into the bio.  For
  now the bioset only holds our mirror_num and stripe_index, but for the
  next merge window I'll shuffle more in."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (25 commits)
  Btrfs: use a btrfs bioset instead of abusing bio internals
  Btrfs: make sure roots are assigned before freeing their nodes
  Btrfs: explicitly use global_block_rsv for quota_tree
  btrfs: do away with non-whole_page extent I/O
  Btrfs: don't invoke btrfs_invalidate_inodes() in the spin lock context
  Btrfs: remove BUG_ON() in btrfs_read_fs_tree_no_radix()
  Btrfs: pause the space balance when remounting to R/O
  Btrfs: fix unprotected root node of the subvolume's inode rb-tree
  Btrfs: fix accessing a freed tree root
  Btrfs: return errno if possible when we fail to allocate memory
  Btrfs: update the global reserve if it is empty
  Btrfs: don't steal the reserved space from the global reserve if their space type is different
  Btrfs: optimize the error handle of use_block_rsv()
  Btrfs: don't use global block reservation for inode cache truncation
  Btrfs: don't abort the current transaction if there is no enough space for inode cache
  Correct allowed raid levels on balance.
  Btrfs: fix possible memory leak in replace_path()
  Btrfs: fix possible memory leak in the find_parent_nodes()
  Btrfs: don't allow device replace on RAID5/RAID6
  Btrfs: handle running extent ops with skinny metadata
  ...

Pull devm usage cleanup from Wolfram Sang:
 "Lately, I have been experimenting how to improve the devm interface to
  make writing device drivers easier and less error prone while also
  getting rid of its subtle issues.  I think it has more potential but
  still needs work and definately conistency, especiall in its usage.

  The first thing I come up with is a low hanging fruit regarding
  devm_ioremap_resouce().  This function already checks if the passed
  resource is valid and gives an error message if not.  So, we can
  remove similar checks from the drivers and get rid of a bit of code
  and a number of inconsistent error strings.

  This series only removes the unneeded check iff devm_ioremap_resource
  follows platform_get_resource directly.  The previous version tried to
  shuffle code if needed, too, what lead to an embarrasing bug.  It
  turned out to me that shuffling code for all cases found will make the
  automated script too complex, so I am unsure if an automated cleanup
  is the proper tool for this case.  Removing the easy stuff seems
  worthwhile to me, though.

  Despite various architectures and platform dependencies, I managed to
  compile test 45 out of 57 modified files locally using heuristics and
  defconfigs."

Pulled because: 296 deletions, 0 additions.

* 'devm_no_resource_check' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (33 commits)
  sound/soc/kirkwood: don't check resource with devm_ioremap_resource
  sound/soc/fsl: don't check resource with devm_ioremap_resource
  arch/mips/lantiq/xway: don't check resource with devm_ioremap_resource
  arch/arm/plat-samsung: don't check resource with devm_ioremap_resource
  arch/arm/mach-tegra: don't check resource with devm_ioremap_resource
  drivers/watchdog: don't check resource with devm_ioremap_resource
  drivers/w1/masters: don't check resource with devm_ioremap_resource
  drivers/video/omap2/dss: don't check resource with devm_ioremap_resource
  drivers/video/omap2: don't check resource with devm_ioremap_resource
  drivers/usb/phy: don't check resource with devm_ioremap_resource
  drivers/usb/host: don't check resource with devm_ioremap_resource
  drivers/usb/gadget: don't check resource with devm_ioremap_resource
  drivers/usb/chipidea: don't check resource with devm_ioremap_resource
  drivers/thermal: don't check resource with devm_ioremap_resource
  drivers/staging/nvec: don't check resource with devm_ioremap_resource
  drivers/staging/dwc2: don't check resource with devm_ioremap_resource
  drivers/spi: don't check resource with devm_ioremap_resource
  drivers/rtc: don't check resource with devm_ioremap_resource
  drivers/pwm: don't check resource with devm_ioremap_resource
  drivers/pinctrl: don't check resource with devm_ioremap_resource
  ...

Pull device tree fixes from Grant Likely:
 "Device tree bug fixes and documentation updates for v3.10

  Nothing earth shattering here.  A build failure fix, and fix for
  releasing nodes and some documenation updates."

* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
  Documentation/devicetree: make semantic of initrd-end more explicit
  of/base: release the node correctly in of_parse_phandle_with_args()
  of/documentation: move video device bindings to a common place
  <linux/of_platform.h>: fix compilation warnings with DT disabled

Pull MIPS fixes from Ralf Baechle:
 "Patching up across the field.  The reversion of the two ASID patches
  is particularly important as it was breaking many platforms."

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: ralink: use the dwc2 driver for the rt305x USB controller
  MIPS: Extract schedule_mfi info from __schedule
  MIPS: Fix sibling call handling in get_frame_info
  MIPS: MSP71xx: remove inline marking of EXPORT_SYMBOL functions
  MIPS: Make virt_to_phys() work for all unmapped addresses.
  MIPS: Fix build error for crash_dump.c in 3.10-rc1
  MIPS: Xway: Fix clk leak
  Revert "MIPS: Allow ASID size to be determined at boot time."
  Revert "MIPS: microMIPS: Support dynamic ASID sizing."

Pull kmemleak patches from Catalin Marinas:
 "Kmemleak now scans all the writable and non-executable module sections
  to avoid false positives (previously it was only scanning specific
  sections and missing .ref.data)."

* tag 'kmemleak-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
  kmemleak: No need for scanning specific module sections
  kmemleak: Scan all allocated, writeable and not executable module sections

Pull arm64 fixes from Catalin Marinas:
 "Fixes for duplicate definition of early_console, kernel/time/Kconfig
  include, __flush_dcache_all() set/way computing, debug (locking, bit
  testing).  The of_platform_populate() was moved to an arch_init_call()
  to allow subsys_init_call() drivers to probe the DT."

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
  arm64: debug: fix mdscr.ss check when enabling debug exceptions
  arm64: Do not source kernel/time/Kconfig explicitly
  arm64: mm: Fix operands of clz in __flush_dcache_all
  arm64: Invoke the of_platform_populate() at arch_initcall() level
  arm64: debug: clear mdscr_el1 instead of taking the OS lock
  arm64: Fix duplicate definition of early_console

devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: John Crispin <blogic@openwrt.org>

devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Stephen Warren <swarren@nvidia.com>

devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>

devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>