Merge branch 'pm-fixes' of master.kernel.org:/pub/scm/linux/kernel/git/khilman/linux-omap-pm into omap-fixes-for-linus

Fix following warning when CONFIG_DEBUG_FS wasn't selected:

arch/arm/mach-omap2/pm-debug.c:57: warning: 'pm_dbg_init' declared 'static' but never defined
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Currently, DSS does not wakeup when there is a DMA request.  DSS wake
up event must be enabled so that the DMA request to refill the FIFO
will wake up the CORE domain.
Signed-off-by: Subramani Venkatesh <subramani.venkatesh@windriver.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

During suspend, the kernel timekeeping subsystem is shut down.  Before
suspend and upon resume, it uses a weak function
read_persistent_clock() to determine the amount of time that elapsed
during suspend.

This function was not implemented on OMAP, so from the timekeeping
subsystem perspective (and thus userspace as well) it appeared that no
time elapsed during suspend.

This patch uses the 32k sync timer as a the persistent clock.

NOTE: This does *NOT* fully handle wrapping of the 32k sync timer, so
      more than one wrapping of the 32k sync timer during suspend may
      cause problems.  Also note there are not interrupts when the 32k
      sync timer wraps, so something else has to be done.
Reported-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Due to OMAP3 erratas 1.157, 1.185 the save of the last pad register
(ETK_D14 and ETK_D15) can fail sometimes when there is simultaneous
OCP access to the SCM register area. Fixed by writing the last
register to the save area.

Also, optimized the delay loop for the HW save to include an udelay(1),
which limits the number of unnecessary HW accesses to SCM register area
during the save.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

val is an u64 pointer, we need an int to check the error.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Wake-up from McBSP ports are needed, especially when the THRESHOLD
dma mode is in use for audio playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

The PM debug code fails to build on when CONFIG_DEBUG_FS is not
enabled.

Build error log:
arch/arm/mach-omap2/built-in.o: In function `omap_sram_idle':
arch/arm/mach-omap2/pm34xx.c:449: undefined reference to `pm_dbg_regset_save'
arch/arm/mach-omap2/pm34xx.c:460: undefined reference to `pm_dbg_regset_save'
arch/arm/mach-omap2/built-in.o: In function `configure_vc':
arch/arm/mach-omap2/pm34xx.c:1237: undefined reference to `pm_dbg_regset_init'
arch/arm/mach-omap2/pm34xx.c:1238: undefined reference to `pm_dbg_regset_init'
make: *** [.tmp_vmlinux1] Error 1

This patch fixes the above errors.

Kernel booting is tested on omap zoom2 and zoom3 boards.
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

As part of Core domain context restoration while coming out of off mode
there are some registers being restored which are not required to be restored.
ROM code will have restored them already. Overwriting some of them can have
potential side effect. Eg: CM_CLKEN_PLL register should not be written while dpll is locked.
Tested on OMAP 3430 SDP for suspend/resume and off mode with sleep_while_idle enabled.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Current value is stored on SDRAM and it is written back during wakeup.
Previously a static value of 0x72 was written there.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Acked-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Previously used u32 as temporary data storage that wraps around at 4.294s.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

This patch removes code blocks that are repeated
in function prcm_setup_regs().
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP interrupt controller goes to unknown state when there is right
combination of l3,l4 sleep/wake-up transitions, l4 autoidle in
interrupt controller and some interrupt. When this happens, interrupts
are not delivered to ARM anymore and ARM will remain in WFI (wait for
interrupt) until interrupt controller is forced to wake-up
(i.e. lauterbach).
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Enable the auto-idle feature of the SCM block to save some additional
power.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Suspending drivers may still generate interrupts just before their suspend is
completed. Any pending interrupts here will prevent sleep.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Don't assume that gpmc_l3_clk is on, enable it before touching
configuration registers.

Note that the current code assumes that this clock is always
enabled. We are already setting smart idle and L3 autogating
for GPMC clock in gpmc_init.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Commit 52650505 caused clock initialization
to fail on OMAP1 with "BUG: spinlock lockup on CPU#0" -- this is because
omap1_select_table_rate() and omap1_round_to_table_rate() call clk_get_rate()
with the clockfw spinlock held.  Fix by accessing the rate directly from
the internal clock framework functions.

Thanks to Tony Lindgren <tony@atomide.com> for reporting and testing the fix.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>

For all DPLL's the valid dividers are same as the values
to be programmed in the register. 0 is an invalid value.
The changes are generated by updating the script which autogenerates
the file modifed in the patch.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

The CHIRONSS has its own local PRCM module and the register defines
need to use the CHIRONSS base and not the PRM base.
The changes are generated by updating the script which autogenerates
the file modifed in the patch.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

The same flag and bits were tested twice.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We need to set the omap_chip.oc carefully for the clocks to work.

To fix this, set the omap_chip.oc in omap3_check_features() based
on the CONTROL_IDCODE and silicon revision registers.

Also add handling for 34xx es3.1.2 as es3.1 for now.

Fixes booting on at least overo board.

Based on an earlier patch by Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Make the omap_mux_read and write available for board code,
and rename omap_mux_set_board_signals into omap_mux_write_array.
Also add the related prototypes and comments into mux.h.

In some cases we want to change the signals dynamically,
mostly for power management.

Note that we cannot use the signal names as they are set
__init to save memory.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Looks like cmdline muxing got broken at some point when we
decided to limit muxing to __init code. Currently omap_mux_entry
list is not yet initialized when we try to initialize cmdline
muxing.

Fix this by calling omap_mux_init_list() before calling
omap_mux_set_cmdline_signals().
Reported-by: Philip Balister <philip@balister.org>
Tested-by: Philip Balister <philip@balister.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The first thing that omap2_init_clksel_parent() does is check for
a non-zero .clksel field in the struct clk.  Therefore, it is
pointless calling this function on clocks where the clksel field
is unset.

Remove init calls to omap2_init_clksel_parent() on clocks without
a clksel field.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

In the current implementation the sysconfig value is read into
 _sysc_cache once and an actual update to the sysconfig register
happens only if the new value paased is differnt from the one in _sysc_cache.
_sysc_cache is updated only if _HWMOD_SYSCONFIG_LOADED is not set.
This can lead to the follwing issue if off mode is enabled in modules
which employs "always-retore" mechanism of context save and restore.

        a. The module sets the sysconfig register through omap_device_enable.
           Here _sysc_cache is updated with the value written to the sysconfig
           register and left.
        b. The power domain containig the module enters off mode and the
           module context is lost.
        c. The module in use becomes active and calls omap_device_enable to
           enable itself. Here a read of sysconfig register does not happen
           as _HWMOD_SYSCONFIG_LOADED flag is set. The value to be written
           to the sysconfig register will be same as the one written in step a.
           Since _sysc_cache reflects the previous written value an update
           of the sysconfig register does not happen.
This means in modules which employs "always-restore" mechanism
after off , the sysconfig regsiters will never get updated.

This patch introduces a flag SYSC_NO_CACHE which if set ensures that the
sysconfig register is always read into _sysc_cache before an update is
attempted.

This flags need to be set only by modules which does not do a context save
but re-initializes the registers every time the module is accessed. This
includes modules like i2c, smartreflex etc.
Signed-off-by: Thara Gopinath <thara@ti.com>
[paul@pwsan.com: tweaked to apply on a different head, added flag comment]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

* git://git.infradead.org/battery-2.6:
  pmu_battery: Fix battery full reporting

/sys/bus/pci/drivers/megaraid_sas/poll_mode_io defaults to being
world-writable, which seems bad (letting any user affect kernel driver
behavior).

This turns off group and user write permissions, so that on typical
production systems only root can write to it.
Signed-off-by: Bryn M. Reeves <bmr@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://gitorious.org/linux-omap-dss2/linux:
  OMAP: DSS2: OMAPFB: fix crash when panel driver was not loaded
  OMAP: DSS2: Reject scaling settings when they cannot be supported
  OMAP: DSS2: Make check-delay-loops consistent
  OMAP: DSS2: OMAPFB: fix omapfb_free_fbmem()
  video/omap: add __init/__exit macros to drivers/video/omap/lcd_htcherald.c
  OMAP: DSS2: Fix compile warning
  MAINTAINERS: Combine DSS2 and OMAPFB2 into one entry
  MAINTAINERS: change omapfb maintainer
  OMAP: OMAPFB: add dummy release function for omapdss
  OMAP: OMAPFB: fix clk_get for RFBI
  OMAP: DSS2: RFBI: convert to new kfifo API
  OMAP: DSS2: Fix crash when panel doesn't define enable_te()
  OMAP: DSS2: Collect interrupt statistics
  OMAP: DSS2: DSI: print debug DCS cmd in hex
  OMAP: DSS2: DSI: fix VC channels in send_short and send_null

There are two copies of list_sort() in the tree already, one in the DRM
code, another in ubifs.  Now XFS needs this as well.  Create a generic
list_sort() function from the ubifs version and convert existing users
to it so we don't end up with yet another copy in the tree.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Maybe this will stop people emailing me about it.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: retry link resume if necessary
  ata_piix: enable 32bit PIO on SATA piix
  sata_promise: don't classify overruns as HSM errors

* master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: Ensure ARMv6/7 mm files are built using appropriate assembler options
  ARM: Fix wrong dmb
  ARM: 5874/1: serial21285: fix disable_irq-from-interrupt-handler deadlock
  ARM: 5873/1: ARM: Fix the reset logic for ARM RealView boards
  ARM: 5872/1: ARM: include needed linux/cpu.h in asm/cpu.h
  ARM: 5871/1: arch/arm: Fix build failure for lpd7a404_defconfig caused by missing includes
  ARM: 5870/1: arch/arm: Fix build failure for defconfigs without CONFIG_ISA_DMA_API set
  ARM: 5868/1: ARM: fix "BUG: using smp_processor_id() in preemptible code"
  ARM: 5867/1: Update U300 defconfig
  ARM: 5866/1: arm ptrace: use unsigned types for kernel pt_regs
  [ARM] pxa: fix strange characters in zaurus gpio .desc
  ARM: add missing recvmmsg syscall number
  [ARM] pxa: fix compiler warnings of unused variable 'id' in cpu_is_pxa9*()
  [ARM] pxa: update pwm_backlight->notify() to include missed 'struct device *'
  [ARM] pxa: enable L2 if present in XSC3
  [ARM] pxa: do not enable L2 after MMU is enabled

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (22 commits)
  MIPS: Ignore vmlinux.*
  MIPS: Move vmlinux.ecoff to arch/mips/boot
  MIPS: cpumask_of_node() should handle -1 as a node
  MIPS: Octeon: Use non-overflowing arithmetic in sched_clock
  MIPS: Malta, PowerTV: Remove unnecessary "Linux started"
  MIPS: BCM63xx: Remove duplicate CONFIG_CMDLINE.
  MIPS: AR7: Remove unused prom_getchar()
  MIPS: PowerTV: Remove extra r4k_clockevent_init() call
  MIPS: Cobalt use strlcat() for the command line arguments
  MIPS: Octeon: Add sched_clock() to csrc-octeon.c
  MIPS: TXx9: Cleanup builtin-cmdline processing
  MIPS: PowerTV: simplify prom_init_cmdline() and merge into prom_init()
  MIPS: PowerTV: Remove unused platform_die()
  MIPS: PowerTV: Remove mips_machine_halt()
  MIPS: PowerTV: Remove unused ptv_memsize
  MIPS: PowerTV: Remove unused prom_getcmdline()
  MIPS: AR7: Remove kgdb_enabled
  MIPS: Alchemy: Correct code taking the size of a pointer
  MIPS: BCM63xx: Fix whitespace damaged board_bcm963xx.c
  MIPS: VR41xx: Use strlcat() for the command line arguments
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - Fix ALC861-VD capture source mixer
  ALSA: ac97: add AC97 STMicroelectronics' codecs
  ALSA: ac97: Add Dell Dimension 2400 to Headphone/Line Jack Sense blacklist
  ASoC: Fix WM8350 DSP mode B configuration
  sbawe: fix memory detection part 2
  sound: oss: off by one bug
  ALSA: usb-audio - Avoid Oops after disconnect
  ALSA: test off by one in setsamplerate()
  ALSA: atiixp: Specify codec for Foxconn RC4107MA-RS2

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits)
  sky2: Fix oops in sky2_xmit_frame() after TX timeout
  Documentation/3c509: document ethtool support
  af_packet: Don't use skb after dev_queue_xmit()
  vxge: use pci_dma_mapping_error to test return value
  netfilter: ebtables: enforce CAP_NET_ADMIN
  e1000e: fix and commonize code for setting the receive address registers
  e1000e: e1000e_enable_tx_pkt_filtering() returns wrong value
  e1000e: perform 10/100 adaptive IFS only on parts that support it
  e1000e: don't accumulate PHY statistics on PHY read failure
  e1000e: call pci_save_state() after pci_restore_state()
  netxen: update version to 4.0.72
  netxen: fix set mac addr
  netxen: fix smatch warning
  netxen: fix tx ring memory leak
  tcp: update the netstamp_needed counter when cloning sockets
  TI DaVinci EMAC: Handle emac module clock correctly.
  dmfe/tulip: Let dmfe handle DM910x except for SPARC on-board chips
  ixgbe: Fix compiler warning about variable being used uninitialized
  netfilter: nf_ct_ftp: fix out of bounds read in update_nl_seq()
  mv643xx_eth: don't include cache padding in rx desc buffer size
  ...

Fix trivial conflict in drivers/scsi/cxgb3i/cxgb3i_offload.c

Fix compilation breakage of all m68knommu targets:

  CC      arch/m68knommu/kernel/asm-offsets.s
In file included from include/linux/sched.h:77,
                 from arch/m68knommu/kernel/asm-offsets.c:12:
include/linux/percpu.h: In function 'per_cpu_ptr_to_phys':
include/linux/percpu.h:161: error: implicit declaration of function 'virt_to_phy

This is broken in linux-2.6.33-rc3.

Change the definitions of __pa() and __va() to not use virt_to_phys()
and phys_to_virt(). Trivial 1:1 conversion required for the non-MMU case.

A side effect if this is that the m68knommu can now use asm/virtconvert.h
for the definition of virt_to_phys() and phys_to_virt().

Also cleaned up the definition of page_to_phys() when moving into
virtconvert.h.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Interestingly, when SIDPR is used in ata_piix, writes to DET in
SControl sometimes get ignored leading to detection failure.  Update
sata_link_resume() such that it reads back SControl after clearing DET
and retry if it's not clear.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: fengxiangjun <fengxiangjun@neusoft.com>
Reported-by: Jim Faulkner <jfaulkne@ccs.neu.edu>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>