- 09 Oct, 2017 24 commits
-
-
Alexander Duyck authored
The following change is meant to update the adaptive ITR algorithm to better support the needs of the network. Specifically with this change what I have done is make it so that our ITR algorithm will try to prevent either starving a socket buffer for memory in the case of Tx, or overrunning an Rx socket buffer on receive. In addition a side effect of the calculations used is that we should function better with new features such as XDP which can handle small packets at high rates without needing to lock us into NAPI polling mode. Signed-off-by:
Alexander Duyck <alexander.h.duyck@intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Emil Tantilov authored
Bits other than FWSM.PT can be set in IXGBE_SWFW_MODE_MASK making the previous check invalid. Change the check for MNG present to be only based on FWSM.PT bit. Signed-off-by:
Emil Tantilov <emil.s.tantilov@intel.com> Tested-by:
-
Emil Tantilov authored
This patch is resolving Coverity hits where padding in a structure could be used uninitialized. - Initialize fwd_cmd.pad/2 before ixgbe_calculate_checksum() - Initialize buffer.pad2/3 before ixgbe_hic_unlocked() Signed-off-by:
-
Jesper Dangaard Brouer authored
The ixgbe driver have page recycle scheme based around the RX-ring queue, where a RX page is shared between two packets. Based on the refcnt, the driver can determine if the RX-page is currently only used by a single packet, if so it can then directly refill/recycle the RX-slot by with the opposite "side" of the page. While this is a clever trick, it is hard to determine when this recycling is successful and when it fails. Adding a counter, which is available via ethtool --statistics as 'alloc_rx_page'. Which counts the number of times the recycle fails and the real page allocator is invoked. When interpreting the stats, do remember that every alloc will serve two packets. The counter is collected per rx_ring, but is summed and ethtool exported as 'alloc_rx_page'. It would be relevant to know what rx_ring that cannot keep up, but that can be exported later if someone experience a need for this. Signed-off-by:
Jesper Dangaard Brouer <brouer@redhat.com> Tested-by:
-
Emil Tantilov authored
Commit: fed21bcee7a5 ("ixgbe: Don't bother clearing buffer memory for descriptor rings) exposed some issues with the logic in the current implementation of ixgbe_clean_test_rings() that are being addressed in this patch: - Split the clearing of the Tx and Rx rings in separate loops. Previously both Tx and Rx rings were cleared in a rx_desc->wb.upper.length based loop which could lead to issues if for w/e reason packets were received outside of the frames transmitted for the loopback test. - Add check for IXGBE_TXD_STAT_DD to avoid clearing the rings if the transmits have not comlpeted by the time we enter ixgbe_clean_test_rings() - Exit early on ixgbe_check_lbtest_frame() failure. This change fixes a crash during ethtool diagnostic (ethtool -t). Signed-off-by: -
Emil Tantilov authored
Ignoring errors when attempting to identify the PHY can lead to a crash. Specifically in the case of FW controlled PHYs where the PHY read/write operations are set to NULL. Removed redundant comment. Signed-off-by:
-
Shannon Nelson authored
Just like when the last VF is removed, we need to restore normal operations after the last macvlan offload is removed, else we get stuck in single queue operations. To test: ethtool -l eth1 # note the number of queues in use, ~= cpus ethtool -K eth1 l2-fwd-offload on ip link add mv1 link eth1 type macvlan mode bridge ip link set dev mv1 up ip link del mv1 ethtool -l eth1 # are we back to the same # of queues, or stuck on 1? Signed-off-by:
Shannon Nelson <shannon.nelson@oracle.com> Tested-by:
-
Bhumika Goyal authored
Declare ixgbe_mac_operations structures as const as they are only stored in the mac_ops field of ixgbe_info structure. This field is of type const and therefore ixgbe_mac_operations structure can be made const too. Signed-off-by:
Bhumika Goyal <bhumirks@gmail.com> Tested-by:
-
Emil Tantilov authored
Added clearing of SW resource bits in the SW/FW synchronization register to ixgbe_init_swfw_sync_X540(). Updated ixgbe_acquire_swfw_sync_X540 SW Manageability host interface resource bit error case to match the error handling of the other SW resource bits. Which is to release the SW resource bits if SW times out while attempting to acquire the resource. This allows the driver to load in cases where the semaphore bits could be stuck after a reset or a crash. Signed-off-by:
-
Christos Gkekas authored
dcb_app priority is unsigned thus checking whether it is less than zero is redundant. Signed-off-by:
Christos Gkekas <chris.gekas@gmail.com> Acked-By:
Tomer Tayar <Tomer.Tayar@cavium.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Christos Gkekas authored
Many macros in dwmac-ipq806x are unused and should be removed. Moreover gmac->id is an unsigned variable and therefore checking whether it is less than zero is redundant. Signed-off-by:
-
David S. Miller authored
Eric Dumazet says: ==================== ipv6: ipv6_dev_get_saddr() rcu works Sending IPv6 udp packets on non connected sockets is quite slow, because ipv6_dev_get_saddr() is still using an rwlock and silly references games on ifa. Tested: $ ./super_netperf 16 -H 4444::555:0786 -l 2000 -t UDP_STREAM -- -m 100 & [1] 12527 Performance is boosted from 2.02 Mpps to 4.28 Mpps Kernel profile before patches : 22.62% [kernel] [k] _raw_read_lock_bh 7.04% [kernel] [k] refcount_sub_and_test 6.56% [kernel] [k] ipv6_get_saddr_eval 5.67% [kernel] [k] _raw_read_unlock_bh 5.34% [kernel] [k] __ipv6_dev_get_saddr 4.95% [kernel] [k] refcount_inc_not_zero 4.03% [kernel] [k] __ip6addrlbl_match 3.70% [kernel] [k] _raw_spin_lock 3.44% [kernel] [k] ipv6_dev_get_saddr 3.24% [kernel] [k] ip6_pol_route 3.06% [kernel] [k] refcount_add_not_zero 2.30% [kernel] [k] __local_bh_enable_ip 1.81% [kernel] [k] mlx4_en_xmit 1.20% [kernel] [k] __ip6_append_data 1.12% [kernel] [k] __ip6_make_skb 1.11% [kernel] [k] __dev_queue_xmit 1.06% [kernel] [k] l3mdev_master_ifindex_rcu Kernel profile after patches : 11.36% [kernel] [k] ip6_pol_route 7.65% [kernel] [k] _raw_spin_lock 7.16% [kernel] [k] __ipv6_dev_get_saddr 6.49% [kernel] [k] ipv6_get_saddr_eval 6.04% [kernel] [k] refcount_add_not_zero 3.34% [kernel] [k] __ip6addrlbl_match 2.62% [kernel] [k] __dev_queue_xmit 2.37% [kernel] [k] mlx4_en_xmit 2.26% [kernel] [k] dst_release 1.89% [kernel] [k] __ip6_make_skb 1.87% [kernel] [k] __ip6_append_data 1.86% [kernel] [k] udpv6_sendmsg 1.86% [kernel] [k] ip6t_do_table 1.64% [kernel] [k] ipv6_dev_get_saddr 1.64% [kernel] [k] find_match 1.51% [kernel] [k] l3mdev_master_ifindex_rcu 1.24% [kernel] [k] ipv6_addr_label ==================== Signed-off-by: -
Eric Dumazet authored
By extending the rcu section a bit, we can avoid these very expensive in6_ifa_put()/in6_ifa_hold() calls done in __ipv6_dev_get_saddr() and ipv6_dev_get_saddr() Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Eric Dumazet authored
Callers hold rcu_read_lock(), so we do not need the rcu_read_lock()/rcu_read_unlock() pair. Signed-off-by:
-
Eric Dumazet authored
Signed-off-by:
-
Eric Dumazet authored
Signed-off-by:
-
Eric Dumazet authored
Signed-off-by:
-
Eric Dumazet authored
inet6_ifa_finish_destroy() already uses kfree_rcu() to free inet6_ifaddr structs. We need to use proper list additions/deletions in order to allow readers to use RCU instead of idev->lock rwlock. Signed-off-by:
-
David S. Miller authored
Roopa Prabhu says: ==================== bridge: neigh msg proxy and flood suppression support This series implements arp and nd suppression in the bridge driver for ethernet vpns. It implements rfc7432, section 10 https://tools.ietf.org/html/rfc7432#section-10 for ethernet VPN deployments. It is similar to the existing BR_PROXYARP* flags but has a few semantic differences to conform to EVPN standard. Unlike the existing flags, this new flag suppresses flood of all neigh discovery packets (arp and nd) to tunnel ports. Supports both vlan filtering and non-vlan filtering bridges. In case of EVPN, it is mainly used to avoid flooding of arp and nd packets to tunnel ports like vxlan. v2 : rebase to latest + address some optimization feedback from Nikolay. v3 : fix kbuild reported build errors with CONFIG_INET off v4 : simplify port flag mask as suggested by stephen v5 : address some feedback from Toshiaki v6 : some v5 cleanups in nd suppress (keep it consistent with arp suppress) ==================== Signed-off-by:
-
Roopa Prabhu authored
This patch avoids flooding and proxies ndisc packets for BR_NEIGH_SUPPRESS ports. Signed-off-by:
Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by:
-
Roopa Prabhu authored
This patch avoids flooding and proxies arp packets for BR_NEIGH_SUPPRESS ports. Moves existing br_do_proxy_arp to br_do_proxy_suppress_arp to support both proxy arp and neigh suppress. Signed-off-by:
-
Roopa Prabhu authored
This patch adds a new bridge port flag BR_NEIGH_SUPPRESS to suppress arp and nd flood on bridge ports. It implements rfc7432, section 10. https://tools.ietf.org/html/rfc7432#section-10 for ethernet VPN deployments. It is similar to the existing BR_PROXYARP* flags but has a few semantic differences to conform to EVPN standard. Unlike the existing flags, this new flag suppresses flood of all neigh discovery packets (arp and nd) to tunnel ports. Supports both vlan filtering and non-vlan filtering bridges. In case of EVPN, it is mainly used to avoid flooding of arp and nd packets to tunnel ports like vxlan. This patch adds netlink and sysfs support to set this bridge port flag. Signed-off-by:
-
Eric Dumazet authored
Ido reported following splat and provided a patch. [ 122.221814] BUG: using smp_processor_id() in preemptible [00000000] code: sshd/2672 [ 122.221845] caller is debug_smp_processor_id+0x17/0x20 [ 122.221866] CPU: 0 PID: 2672 Comm: sshd Not tainted 4.14.0-rc3-idosch-next-custom #639 [ 122.221880] Hardware name: Mellanox Technologies Ltd. MSN2100-CB2FO/SA001017, BIOS 5.6.5 06/07/2016 [ 122.221893] Call Trace: [ 122.221919] dump_stack+0xb1/0x10c [ 122.221946] ? _atomic_dec_and_lock+0x124/0x124 [ 122.221974] ? ___ratelimit+0xfe/0x240 [ 122.222020] check_preemption_disabled+0x173/0x1b0 [ 122.222060] debug_smp_processor_id+0x17/0x20 [ 122.222083] ip6_pol_route+0x1482/0x24a0 ... I believe we can simplify this code path a bit, since we no longer hold a read_lock and need to release it to avoid a dead lock. By disabling BH, we make sure we'll prevent code re-entry and rt6_get_pcpu_route()/rt6_make_pcpu_route() run on the same cpu. Fixes: 66f5d6ce ("ipv6: replace rwlock with rcu and spinlock in fib6_table") Reported-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linuxDavid S. Miller authored
Saeed Mahameed says: ==================== Mellanox, mlx5 updates 2017-10-06 This series includes some shared code updates for kernel 4.15 to both net-next and rdma-next trees. The series includes mlx5 low level flow steering updates and optimizations to support firmware command parallelism for flow steering requests from Maor Gottlieb and two other small fixes from Matan and Maor. One fix from Matan adds error handling for when the destination list of the flow steering rule is full. Maor introduced a patch to avoid NULL pointer dereference on steering cleanup. Then Some refactoring patches needed by the series for code sharing purposes. and split the Flow Table Entry (FTE) and Flow Group (FG) creation code to two parts: 1) Object allocation - allocate the steering node and initialize its resources. 2) The firmware command execution. This change will give us the ability to take write lock on the parent node (e.g. FG for FTE creating) only on the software data struct allocation and creation part of the procedure where the synchronization is really required, and will allow us to execute multiple firmware commands simultaneously and overcome the firmware bottleneck. Refactor the locking scheme of the mlx5 core flow steering as follows: 1) Replace the mutex lock with readers-writers semaphore and take the write lock only when necessary (e.g. allocating a new flow table entry index or adding a node to the parent's children list). When we try to find a suitable child in the parent's children list (e.g. search for flow group with the same match_criteria of the rule) then we only take the read lock. 2) Add versioning mechanism - each steering entity (FT, FG, FTE, DST) will have an incremental version. The version is increased when the entity is changed (e.g. when a new FTE was added to FG - the FG's version is increased). Versioning is used in order to determine if the last traverse of an entity's children is valid or a rescan under write lock is required. Last patch adds FGs and FTEs memory pool, It is useful because these objects are not small and could be allocated/deallocated many times. This support improves the insertion rate of steering rules from ~5k/sec to ~40k/sec. ==================== Signed-off-by:
-
- 08 Oct, 2017 7 commits
-
-
David S. Miller authored
Haiyang Zhang says: ==================== hv_netvsc: support changing TCP hash level The patch set simplifies the existing hash level switching code for UDP. It also adds the support for changing TCP hash level. So users can switch between L3 an L4 hash levels for TCP and UDP. ==================== Signed-off-by: -
Haiyang Zhang authored
Update Documentation/networking/netvsc.txt for TCP hash level setting and related info. Signed-off-by:
Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by:
-
Haiyang Zhang authored
The patch supports the options to switch TCP hash level between L3 and L4 by ethtool command. TCP over IPv4 and v6 can be set differently. The default hash level is L4. We currently only allow switching TX hash level from within the guests. For example, for TCP over IPv4 on eth0: To include TCP port numbers in hashing: ethtool -N eth0 rx-flow-hash tcp4 sdfn To exclude TCP port numbers in hashing: ethtool -N eth0 rx-flow-hash tcp4 sd To show TCP hash level: ethtool -n eth0 rx-flow-hash tcp4 Signed-off-by:
-
Haiyang Zhang authored
This simplifies the logic and make it easier to add more options. Signed-off-by:
-
David S. Miller authored
Jiri Pirko says: ==================== mlxsw: Add more extack error reporting Ido says: Add error messages to VLAN and bridge enslavements to help users understand why the enslavement failed. ==================== Signed-off-by: -
Ido Schimmel authored
The code that actually takes care of bridge offload introduces a few more non-trivial constraints with regards to bridge enslavements. Propagate extack there to indicate the reason. $ ip link add link enp1s0np1 name enp1s0np1.10 type vlan id 10 $ ip link add link enp1s0np1 name enp1s0np1.20 type vlan id 20 $ ip link add name br0 type bridge $ ip link set dev enp1s0np1.10 master br0 $ ip link set dev enp1s0np1.20 master br0 Error: spectrum: Can not bridge VLAN uppers of the same port. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Acked-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
Ido Schimmel authored
Similar to physical ports, enslavement of VLAN devices can also fail. Use extack to indicate why the enslavement failed. $ ip link add link enp1s0np1 name enp1s0np1.10 type vlan id 10 $ ip link add name bond0 type bond mode 802.3ad $ ip link set dev enp1s0np1.10 master bond0 Error: spectrum: VLAN devices only support bridge and VRF uppers. Signed-off-by:
-
- 07 Oct, 2017 9 commits
-
-
David S. Miller authored
Martin KaFai Lau says: ==================== bpf: Misc improvements and a new usage on bpf obj name The first two patches make improvements on the bpf obj name. The last patch adds the prog name to kallsyms. ==================== Signed-off-by: -
Martin KaFai Lau authored
This patch makes the bpf_prog's name available in kallsyms. The new format is bpf_prog_tag[_name]. Sample kallsyms from running selftests/bpf/test_progs: [root@arch-fb-vm1 ~]# egrep ' bpf_prog_[0-9a-fA-F]{16}' /proc/kallsyms ffffffffa0048000 t bpf_prog_dabf0207d1992486_test_obj_id ffffffffa0038000 t bpf_prog_a04f5eef06a7f555__123456789ABCDE ffffffffa0050000 t bpf_prog_a04f5eef06a7f555 Signed-off-by:Martin KaFai Lau <kafai@fb.com> Acked-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Alexei Starovoitov <ast@fb.com> Signed-off-by:
-
Martin KaFai Lau authored
Instead of u8, use char for prog and map name. It can avoid the userspace tool getting compiler's signess warning. The bpf_prog_aux, bpf_map, bpf_attr, bpf_prog_info and bpf_map_info are changed. Signed-off-by:
-
Martin KaFai Lau authored
During get_info_by_fd, the prog/map name is memcpy-ed. It depends on the prog->aux->name and map->name to be zero initialized. bpf_prog_aux is easy to guarantee that aux->name is zero init. The name in bpf_map may be harder to be guaranteed in the future when new map type is added. Hence, this patch makes bpf_obj_name_cpy() to always zero init the prog/map name. Suggested-by:
-
William Tu authored
Similarly to early patch for erspan_xmit(), the ARPHDR_ETHER device is the length of the whole ether packet. So skb->len should subtract the dev->hard_header_len. Fixes: 1a66a836 ("gre: add collect_md mode to ERSPAN tunnel") Fixes: 84e54fe0 ("gre: introduce native tunnel support for ERSPAN") Signed-off-by:
William Tu <u9012063@gmail.com> Cc: Xin Long <lucien.xin@gmail.com> Cc: David Laight <David.Laight@aculab.com> Reviewed-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Lin Zhang authored
The phonet_protocol structs don't need to be written by anyone and so can be marked as const. Signed-off-by:
Lin Zhang <xiaolou4617@gmail.com> Signed-off-by:
-
Lin Zhang authored
Signed-off-by:
-
David S. Miller authored
Yonghong Song says: ==================== bpf: add two helpers to read perf event enabled/running time Hardware pmu counters are limited resources. When there are more pmu based perf events opened than available counters, kernel will multiplex these events so each event gets certain percentage (but not 100%) of the pmu time. In case that multiplexing happens, the number of samples or counter value will not reflect the case compared to no multiplexing. This makes comparison between different runs difficult. Typically, the number of samples or counter value should be normalized before comparing to other experiments. The typical normalization is done like: normalized_num_samples = num_samples * time_enabled / time_running normalized_counter_value = counter_value * time_enabled / time_running where time_enabled is the time enabled for event and time_running is the time running for event since last normalization. This patch set implements two helper functions. The helper bpf_perf_event_read_value reads counter/time_enabled/time_running for perf event array map. The helper bpf_perf_prog_read_value read counter/time_enabled/time_running for bpf prog with type BPF_PROG_TYPE_PERF_EVENT. ==================== Signed-off-by: -
Yonghong Song authored
The bpf sample program trace_event is enhanced to use the new helper to print out enabled/running time. Signed-off-by:
Yonghong Song <yhs@fb.com> Acked-by:
-
