Currently PACKET_TX_RING forces certain amount of every frame to remain
unused. This probably originates from an early version of the
PACKET_TX_RING patch that in fact used the extra space when the (since
removed) CONFIG_PACKET_MMAP_ZERO_COPY option was enabled. The current
code does not make any use of this extra space.

This patch removes the extra space reservation and lets userspace make
use of the full frame size.
Signed-off-by: Gabor Gombas <gombasg@sztaki.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>

I found that the current version of drivers/net/usb/dm9601.c can be used to
successfully drive a low-power, low-cost network adapter with USB ID
0a46:9000, based on a DM9000E chipset. As no device with this ID is yet
present in the kernel, I have created a patch that adds support for the device
to the dm9601 driver.

Created and tested against linux-2.6.32-rc5.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mailbox command process would only process a maximum of 5 unrelated
firmware events while waiting for it's command completion status.
It should process an unlimited number of events while waiting for a maximum of 5 seconds.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clean up driver resources without touch the hardware. Add pci
save/restore state.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Augment raw_send_hdrinc to correct for incorrect ip header length values

A series of oopses was reported to me recently.  Apparently when using AF_RAW
sockets to send data to peers that were reachable via ipsec encapsulation,
people could panic or BUG halt their systems.

I've tracked the problem down to user space sending an invalid ip header over an
AF_RAW socket with IP_HDRINCL set to 1.

Basically what happens is that userspace sends down an ip frame that includes
only the header (no data), but sets the ip header ihl value to a large number,
one that is larger than the total amount of data passed to the sendmsg call.  In
raw_send_hdrincl, we allocate an skb based on the size of the data in the msghdr
that was passed in, but assume the data is all valid.  Later during ipsec
encapsulation, xfrm4_tranport_output moves the entire frame back in the skbuff
to provide headroom for the ipsec headers.  During this operation, the
skb->transport_header is repointed to a spot computed by
skb->network_header + the ip header length (ihl).  Since so little data was
passed in relative to the value of ihl provided by the raw socket, we point
transport header to an unknown location, resulting in various crashes.

This fix for this is pretty straightforward, simply validate the value of of
iph->ihl when sending over a raw socket.  If (iph->ihl*4U) > user data buffer
size, drop the frame and return -EINVAL.  I just confirmed this fixes the
reported crashes.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In mii monitor mode, bond_check_dev_link() calls the the ioctl
handler of slave devices. It stores the ndo_do_ioctl function
pointer to a static (!) ioctl variable and later uses it to call the
handler with the IOCTL macro.

If another thread executes bond_check_dev_link() at the same time
(even with a different bond, which none of the locks prevent), a
race condition occurs. If the two racing slaves have different
drivers, this may result in one driver's ioctl handler being
called with a pointer to a net_device controlled with a different
driver, resulting in unpredictable breakage.

Unless I am overlooking something, the "static" must be a
copy'n'paste error (?).
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

virtio net used to unlink skbs from send queues on error,
but ever since 48925e37
we do not do this. This causes guest data corruption and crashes
with vhost since net core can requeue the skb or free it without
it being taken off the list.

This patch fixes this by queueing the skb after successful
transmit.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Page buffers containing packets with an incorrect checksum or using a
protocol not handled by hardware checksum offload were previously not
passed to LRO.  The conversion to GRO changed this, but did not set
the ip_summed value accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The BNX2_L2CTX_STATUSB_NUM definition needs to be changed to match
the recent firmware update:

commit 078b0735
bnx2: Update firmware to 5.0.0.j3.

Without the fix, bnx2 can crash intermittently in bnx2_rx_int() when
iSCSI is enabled.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cc: users@rt2x00.serialmonkey.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Test whether index is within bounds before reading the element
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When hostapd injects a frame, e.g. an authentication or association
response, mac80211 looks for a suitable access point virtual interface
to associate the frame with based on its source address. This makes it
possible e.g. to correctly assign sequence numbers to the frames.

A small typo in the ethernet address comparison statement caused a
failure to find a suitable ap interface. Sequence numbers on such
frames where therefore left unassigned causing some clients
(especially windows-based 11b/g clients) to reject them and fail to
authenticate or associate with the access point. This patch fixes the
typo in the address comparison statement.
Signed-off-by: Björn Smedman <bjorn.smedman@venatech.se>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes the following sparse warnings:

$ make modules SUBDIRS=drivers/net/wireless/libertas C=1 CF=-D__CHECK_ENDIAN__
make: Entering directory `/usr/src/linux-wl'
  CHECK   drivers/net/wireless/libertas/if_spi.c
drivers/net/wireless/libertas/if_spi.c:137:16: warning: incorrect type in initializer (different base types)
drivers/net/wireless/libertas/if_spi.c:137:16:    expected unsigned short [unsigned] [usertype] reg_out
drivers/net/wireless/libertas/if_spi.c:137:16:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:191:16: warning: incorrect type in initializer (different base types)
drivers/net/wireless/libertas/if_spi.c:191:16:    expected unsigned short [unsigned] [usertype] reg_out
drivers/net/wireless/libertas/if_spi.c:191:16:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:256:24: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/libertas/if_spi.c:256:24:    expected restricted __le32 const [usertype] *p
drivers/net/wireless/libertas/if_spi.c:256:24:    got unsigned int *<noident>
drivers/net/wireless/libertas/if_spi.c:243:24: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/libertas/if_spi.c:243:24:    expected restricted __le16 const [usertype] *p
drivers/net/wireless/libertas/if_spi.c:243:24:    got unsigned short *<noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:243:24: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/libertas/if_spi.c:243:24:    expected restricted __le16 const [usertype] *p
drivers/net/wireless/libertas/if_spi.c:243:24:    got unsigned short *<noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:243:24: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/libertas/if_spi.c:243:24:    expected restricted __le16 const [usertype] *p
drivers/net/wireless/libertas/if_spi.c:243:24:    got unsigned short *<noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:243:24: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/libertas/if_spi.c:243:24:    expected restricted __le16 const [usertype] *p
drivers/net/wireless/libertas/if_spi.c:243:24:    got unsigned short *<noident>
drivers/net/wireless/libertas/if_spi.c:243:24: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/libertas/if_spi.c:243:24:    expected restricted __le16 const [usertype] *p
drivers/net/wireless/libertas/if_spi.c:243:24:    got unsigned short *<noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:171:7: warning: incorrect type in assignment (different base types)
drivers/net/wireless/libertas/if_spi.c:171:7:    expected unsigned short [unsigned] [usertype] buff
drivers/net/wireless/libertas/if_spi.c:171:7:    got restricted __le16 [usertype] <noident>
drivers/net/wireless/libertas/if_spi.c:243:24: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/libertas/if_spi.c:243:24:    expected restricted __le16 const [usertype] *p
drivers/net/wireless/libertas/if_spi.c:243:24:    got unsigned short *<noident>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix a typo in the description of hwmp_route_info_get(), no function
changes.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When the in-kernel SME gets an association failure from
the AP we don't deauthenticate, and thus get into a very
confused state which will lead to warnings later on. Fix
this by actually deauthenticating when the AP indicates
an association failure.

(Brought to you by the hacking session at Kernel Summit 2009 in Tokyo,
Japan. -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When association fails, we should stay authenticated,
which in mac80211 is represented by the existence of
the mlme work struct, so we cannot free that, instead
we need to just set it to idle.

(Brought to you by the hacking session at Kernel Summit 2009 in Tokyo,
Japan. -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Recent commit "mac80211: fix logic error ibss merge bssid check" fixed
joining of ibss cell when static bssid is provided. In this case
ifibss->bssid is set before the cell is joined and comparing that address
to a bss should thus always succeed. Unfortunately this change broke the
other case of joining a ibss cell without providing a static bssid where
the value of ifibss->bssid is not set before the cell is joined.

Since ifibss->bssid may be set before or after joining the cell we do not
learn anything by comparing it to a known bss. Remove this check.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

'struct b43_wl' declaration is missing at 'leds.h'.
It should be declared to avoid getting some GCC warnings at 'b43_leds_unregister'.
Signed-off-by: Miguel Botón <mboton@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

"b43: Fix PPC crash in rfkill polling on unload" fixed the bug reported
in Bugzilla No. 14181; however, it introduced a new bug. Whenever the
radio switch was turned off, it was necessary to unload and reload
the driver for it to recognize the switch again.

This patch fixes both the original bug in #14181 and the bug introduced by
the previous patch. It must be stated, however, that if there is a BCM4306/3
with an rfkill switch (not yet proven), then the driver will need an
unload/reload cycle to turn the device back on.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add include asm/cacheflush.h,  because declaration of __flush_purge_region
moved to asm/cacheflush.h.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Be more careful about the state of pointers during tear-down.
The "pppoe_dev" field can only be looked at safely while holding socket locks.
This subsequently allows for the flush_lock to be killed.

We depend on the PPPOX_CONNECTED state to tell us that that those fields are
valid, so whoever clears that state (pppox_unbind_sock()) is responsible for
the dev_put() call.

We also have to ensure that we delete_item() on all sockets before they are
cleaned up.

The need for these changes has been exposed by scenarios wherein namespace
bindings of ethernet devices change while there are ongoing PPPoE sessions,
which resulted in oopses due to unusual socket connection termination paths,
exposing these issues.
Signed-off-by: Michal Ostrowski <mostrows@gmail.com>
Reviewed-by: Cyril Gorcunov <gorcunov@gmail.com>
Reported-by: Denys Fedoryschenko <denys@visp.net.lb>
Tested-by: Denys Fedoryschenko <denys@visp.net.lb>

PCH-based parts (82577/82578) and some ICH8-based parts (82566) need to
hold the swflag (sw/fw/hw hardware semaphore) over consecutive PHY accesses
in order to perform sw-driven PHY configuration during initialization to
workaround known hardware issues (see follow-on patch).  This patch
provides new PHY read/write functions (and function pointers) that will
allow accessing the PHY registers assuming the swflag has already been
acquired.  The actual PHY register access code has moved into helper
functions that are called with a flag indicating whether or not the swflag
has already been acquired and acquires/releases it if not.

The functions called from within the updated PHY access functions had to be
updated to assume the swflag was already acquired, and other functions that
called those functions were also updated to acquire/release the swflag.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Accesses to NVM and PHY/CSR registers on ICHx/PCH-based parts are protected
from concurrent accesses with a mutex that is acquired when the access is
initiated and released when the access has completed.  However, the two
types of accesses should not be protected by the same mutex because the
driver may have to access the NVM while already holding the mutex over
several consecutive PHY/CSR accesses which would result in livelock.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Unlike previous ICHx-based parts, the PCH-based parts (82577/82578) require
LPLU (Low Power Link Up, or "reverse auto-negotiation") to be configured in
the PHY rather than the MAC.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In some conditions (e.g. when AMT is enabled on the system), it is possible
to take an extended period of time to for the driver to acquire the sw/fw/hw
hardware semaphore used to protect against concurrent access of a shared
resource (e.g. PHY registers).  This could cause PHY registers to not get
configured properly resulting in link issues.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Performing a dummy read of the PHY Wakeup Control (WUC) register clears the
wakeup enable bit set by an PHY reset.  If this bit remains set, link
problems may occur.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch resolves a memory leak which occurs while changing the ring size
while the interface is down.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch resolves a memory leak that occurs when you resize the rings via
the ethtool -G option while the interface is down.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changing ring sizes while the interface was down was causing a double
allocation of the receive and transmit rings.  This issue is amplified when
there are multiple rings enabled.  To prevent this we need to add an
additional check which will just update the ring counts when the interface
is not up and skip the allocation steps.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Modify bonding hash transmit policies to use the psource MAC address of
the packet instead of the MAC address configured for the bonding device.

The old sitation conflicts with the documentation.
Signed-off-by: Jasper Spaans <spaans@fox-it.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While playing with pktgen, I realized IP ID was not filled and a
random value was taken, possibly leaking 2 bytes of kernel memory.
 
We can use an increasing ID, this can help diagnostics anyway.

Also clear packet payload, instead of leaking kernel memory.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The DM9000B revision ID is 0x1A, not 0x1B as set in the curernt
dm9000.h header.

Fix bug reported by Paolo Zebelloni.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 8110SC rev d chip on our board shows a regression which the 8110SB chip
did not have. When inbound traffic is overflowing the receive descriptor queue,
"holes" in the ring buffer may occur which lead to a hangup until the buffer
is filled again. The packets are than completely processed, but the ring
remains porous and no packets are processed until the next overflow. Setting
the interface down and up can fix the problem temporary from userspace.

For some reason we don't know, this behaviour is not occuring if the RxVlan
bit for hardware VLAN untagging is set. There is another "Work around for
AMD plateform" in the current code which checks the VLAN status
word in receive descriptors, but does never come to effect when hardware
VLAN support is enabled. We assume that this is a bug in the chip.

The following patch fixes the problem. Without the patch we could reproduce
the hang within minutes (given other devices also generating lots of
interrupts), without we couldn't reproduce within a few days of long term
testing.

This version contains minor style adjustments and is sent with mutt which
will hopefully not destroy the formatting again.
Signed-off-by: Bernhard Schmidt <bernhard.schmidt@saxnet.de>
Signed-off-by: Simon Wunderlich <simon.wunderlich@saxnet.de>
Acked-by: Francois Romieu <romieu@zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

At this point (ri_tasklet()), RTNL or dev_base_lock are not held,
we must use dev_get_by_index() instead of __dev_get_by_index()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fixes the following build failure:
  CC      drivers/net/au1000_eth.o
/drivers/net/au1000_eth.c: In function 'au1000_set_settings':
/drivers/net/au1000_eth.c:623: error: implicit declaration of function 'capable'
/drivers/net/au1000_eth.c:623: error: 'CAP_NET_ADMIN' undeclared (first use in this function)
/drivers/net/au1000_eth.c:623: error: (Each undeclared identifier is reported only once
/drivers/net/au1000_eth.c:623: error: for each function it appears in.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Improve the reporting of myri10ge port type in ethtool,
and update for new boards.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit b6b39e8f (tcp: Try to catch MSG_PEEK bug) added a printk()
to the WARN_ON() that's in tcp.c. This patch changes this combination
to WARN(); the advantage of WARN() is that the printk message shows up
inside the message, so that kerneloops.org will collect the message.

In addition, this gets rid of an extra if() statement.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PHY on 82577/82578 parts needs a soft reset when transitioning to Sx
state in order for the PHY write which disables gigabit speed to take
effect.  Gigabit speed must be disabled in order for the PHY writes to
registers on page 800 (the wakeup control registers) to work as expected
otherwise the system might not wake via WoL.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>