For flow offload adds, if the rhash insert code fails, the flow will still
have been offloaded but the reference to it in the driver freed.

Re-order the offload setup calls to ensure that a flow will only be written
to FW if a kernel reference is held and stored in the rhashtable. Remove
this hashtable entry if the offload fails.

Fixes: c01d0efa ("nfp: flower: use rhashtable for flow caching")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Calling nfp_compile_flow_metadata both assigns a stats context and
increments a ref counter on (or allocates) a mask id table entry. These
are released by the nfp_modify_flow_metadata call on flow deletion,
however, if a flow add fails after metadata is set then the flow entry
will be deleted but the metadata assignments leaked.

Add an error path to the flow add offload function to ensure allocated
metadata is released in the event of an offload fail.

Fixes: 81f3ddf2 ("nfp: add control message passing capabilities to flower offloads")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously when unbinding a slave the 802.3ad implementation only told
partner that the port is not suitable for aggregation by setting the port
aggregation state from aggregatable to individual. This is not enough. If the
physical layer still stays up and we only unbinded this port from the bond there
is nothing in the aggregation status alone to prevent the partner from sending
traffic towards us. To ensure that the partner doesn't consider this
port at all anymore we should also disable collecting and distributing to
signal that this actor is going away. Also clear AD_STATE_SYNCHRONIZATION to
ensure partner exits collecting + distributing state.

I have tested this behaviour againts Arista EOS switches with mlx5 cards
(physical link stays up even when interface is down) and simulated
the same situation virtually Linux <-> Linux with two network namespaces
running two veth device pairs. In both cases setting aggregation to
individual doesn't alone prevent traffic from being to sent towards this
port given that the link stays up in partners end. Partner still keeps
it's end in collecting + distributing state and continues until timeout is
reached. In most cases this means we are losing the traffic partner sends
towards our port while we wait for timeout. This is most visible with slow
periodic time (LACP rate slow).

Other open source implementations like Open VSwitch and libreswitch, and
vendor implementations like Arista EOS, seem to disable collecting +
distributing to when doing similar port disabling/detaching/removing change.
With this patch kernel implementation would behave the same way and ensure
partner doesn't consider our actor viable anymore.
Signed-off-by: Toni Peltonen <peltzi@peltzi.fi>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The last set of csum offload fixes had a leak:

Checksum enabled status bits from rx descriptor were incorrectly
interpreted. Consequently all the other valid logic worked on zero bits.
That caused rx checksum offloads never to trigger.

Tested by dumping rx descriptors and validating resulting csum_level.
Reported-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Fixes: ad703c2b ("net: aquantia: invalid checksumm offload implementation")
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a spelling mistake in a net_warn_ratelimited message, fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a spelling mistake in the oct_stats_strings array, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Setting up and tearing down debugfs is current unbalanced, as seen by
this error during resume from suspend:

    [  752.134067] dwc-eth-dwmac 2490000.ethernet eth0: ERROR failed to create debugfs directory
    [  752.134347] dwc-eth-dwmac 2490000.ethernet eth0: stmmac_hw_setup: failed debugFS registration

The imbalance happens because the driver creates the debugfs hierarchy
when the device is opened and tears it down when the device is closed.
There's little gain in that, and it could be argued that it is even
surprising because it's not usually done for other devices. Fix the
imbalance by moving the debugfs creation and teardown to the driver's
->probe() and ->remove() implementations instead.

Note that the ring descriptors cannot be read while the interface is
down, so make sure to return an empty file when the descriptors_status
debugfs file is read.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp_assoc_update_frag_point() should be called whenever asoc->pathmtu
changes, but we missed one place in sctp_association_init(). It would
cause frag_point is zero when sending data.

As says in Jakub's reproducer, if sp->pathmtu is set by socketopt, the
new asoc->pathmtu inherits it in sctp_association_init(). Later when
transports are added and their pmtu >= asoc->pathmtu, it will never
call sctp_assoc_update_frag_point() to set frag_point.

This patch is to fix it by updating frag_point after asoc->pathmtu is
set as sp->pathmtu in sctp_association_init(). Note that it moved them
after sctp_stream_init(), as stream->si needs to be set first.

Frag_point's calculation is also related with datachunk's type, so it
needs to update frag_point when stream->si may be changed in
sctp_process_init().

v1->v2:
  - call sctp_assoc_update_frag_point() separately in sctp_process_init
    and sctp_association_init, per Marcelo's suggestion.

Fixes: 2f5e3c9d ("sctp: introduce sctp_assoc_update_frag_point")
Reported-by: Jakub Audykowicz <jakub.audykowicz@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

__qdisc_drop_all() accesses skb->prev to get to the tail of the
segment-list.

With commit 68d2f84a ("net: gro: properly remove skb from list")
the skb-list handling has been changed to set skb->next to NULL and set
the list-poison on skb->prev.

With that change, __qdisc_drop_all() will panic when it tries to
dereference skb->prev.

Since commit 992cba7e ("net: Add and use skb_list_del_init().")
__list_del_entry is used, leaving skb->prev unchanged (thus,
pointing to the list-head if it's the first skb of the list).
This will make __qdisc_drop_all modify the next-pointer of the list-head
and result in a panic later on:

[   34.501053] general protection fault: 0000 [#1] SMP KASAN PTI
[   34.501968] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 4.20.0-rc2.mptcp #108
[   34.502887] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 0.5.1 01/01/2011
[   34.504074] RIP: 0010:dev_gro_receive+0x343/0x1f90
[   34.504751] Code: e0 48 c1 e8 03 42 80 3c 30 00 0f 85 4a 1c 00 00 4d 8b 24 24 4c 39 65 d0 0f 84 0a 04 00 00 49 8d 7c 24 38 48 89 f8 48 c1 e8 03 <42> 0f b6 04 30 84 c0 74 08 3c 04
[   34.507060] RSP: 0018:ffff8883af507930 EFLAGS: 00010202
[   34.507761] RAX: 0000000000000007 RBX: ffff8883970b2c80 RCX: 1ffff11072e165a6
[   34.508640] RDX: 1ffff11075867008 RSI: ffff8883ac338040 RDI: 0000000000000038
[   34.509493] RBP: ffff8883af5079d0 R08: ffff8883970b2d40 R09: 0000000000000062
[   34.510346] R10: 0000000000000034 R11: 0000000000000000 R12: 0000000000000000
[   34.511215] R13: 0000000000000000 R14: dffffc0000000000 R15: ffff8883ac338008
[   34.512082] FS:  0000000000000000(0000) GS:ffff8883af500000(0000) knlGS:0000000000000000
[   34.513036] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   34.513741] CR2: 000055ccc3e9d020 CR3: 00000003abf32000 CR4: 00000000000006e0
[   34.514593] Call Trace:
[   34.514893]  <IRQ>
[   34.515157]  napi_gro_receive+0x93/0x150
[   34.515632]  receive_buf+0x893/0x3700
[   34.516094]  ? __netif_receive_skb+0x1f/0x1a0
[   34.516629]  ? virtnet_probe+0x1b40/0x1b40
[   34.517153]  ? __stable_node_chain+0x4d0/0x850
[   34.517684]  ? kfree+0x9a/0x180
[   34.518067]  ? __kasan_slab_free+0x171/0x190
[   34.518582]  ? detach_buf+0x1df/0x650
[   34.519061]  ? lapic_next_event+0x5a/0x90
[   34.519539]  ? virtqueue_get_buf_ctx+0x280/0x7f0
[   34.520093]  virtnet_poll+0x2df/0xd60
[   34.520533]  ? receive_buf+0x3700/0x3700
[   34.521027]  ? qdisc_watchdog_schedule_ns+0xd5/0x140
[   34.521631]  ? htb_dequeue+0x1817/0x25f0
[   34.522107]  ? sch_direct_xmit+0x142/0xf30
[   34.522595]  ? virtqueue_napi_schedule+0x26/0x30
[   34.523155]  net_rx_action+0x2f6/0xc50
[   34.523601]  ? napi_complete_done+0x2f0/0x2f0
[   34.524126]  ? kasan_check_read+0x11/0x20
[   34.524608]  ? _raw_spin_lock+0x7d/0xd0
[   34.525070]  ? _raw_spin_lock_bh+0xd0/0xd0
[   34.525563]  ? kvm_guest_apic_eoi_write+0x6b/0x80
[   34.526130]  ? apic_ack_irq+0x9e/0xe0
[   34.526567]  __do_softirq+0x188/0x4b5
[   34.527015]  irq_exit+0x151/0x180
[   34.527417]  do_IRQ+0xdb/0x150
[   34.527783]  common_interrupt+0xf/0xf
[   34.528223]  </IRQ>

This patch makes sure that skb->prev is set to NULL when entering
netem_enqueue.

Cc: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Cc: Tyler Hicks <tyhicks@canonical.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Fixes: 68d2f84a ("net: gro: properly remove skb from list")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a session in X25_STATE_1 (Awaiting Call Accept) receives a call
request, the session will be closed (x25_disconnect), cause=0x01
(Number Busy) and diag=0x48 (Call Collision) will be set and a clear
request will be send.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

o x25_find_listener(): the compare for the null_x25_address was wrong.
   We have to check the x25_addr of the listener socket instead of the
   x25_addr of the incomming call.

 o x25_bind(): it was not possible to bind a socket to null_x25_address
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The length of the called and calling address was not calculated
correctly (BCD encoding).
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

SFP standards are now available from the SNIA (Storage Networking
Industry Association) website.

Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sabrina Dubroca says:

====================
fixes for XPS configuration after Symmetric queue selection

This fixes some bugs introduced by the "Symmetric queue selection
using XPS for Rx queues".

First, the refactoring of the cleanup function skipped resetting the
queue's NUMA node under some conditions.

Second, the accounting on static keys for XPS and RXQS-XPS is
unbalanced, so the static key for XPS won't actually disable itself,
once enabled. The RXQS-XPS static key can actually be disabled by
reconfiguring a device that didn't have RXQS-XPS configured at all.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 04157469 ("net: Use static_key for XPS maps") introduced a
static key for XPS, but the increments/decrements don't match.

First, the static key's counter is incremented once for each queue, but
only decremented once for a whole batch of queues, leading to large
unbalances.

Second, the xps_rxqs_needed key is decremented whenever we reset a batch
of queues, whether they had any rxqs mapping or not, so that if we setup
cpu-XPS on em1 and RXQS-XPS on em2, resetting the queues on em1 would
decrement the xps_rxqs_needed key.

This reworks the accounting scheme so that the xps_needed key is
incremented only once for each type of XPS for all the queues on a
device, and the xps_rxqs_needed key is incremented only once for all
queues. This is sufficient to let us retrieve queues via
get_xps_queue().

This patch introduces a new reset_xps_maps(), which reinitializes and
frees the appropriate map (xps_rxqs_map or xps_cpus_map), and drops a
reference to the needed keys:
 - both xps_needed and xps_rxqs_needed, in case of rxqs maps,
 - only xps_needed, in case of CPU maps.

Now, we also need to call reset_xps_maps() at the end of
__netif_set_xps_queue() when there's no active map left, for example
when writing '00000000,00000000' to all queues' xps_rxqs setting.

Fixes: 04157469 ("net: Use static_key for XPS maps")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before commit 80d19669 ("net: Refactor XPS for CPUs and Rx queues"),
netif_reset_xps_queues() did netdev_queue_numa_node_write() for all the
queues being reset. Now, this is only done when the "active" variable in
clean_xps_maps() is false, ie when on all the CPUs, there's no active
XPS mapping left.

Fixes: 80d19669 ("net: Refactor XPS for CPUs and Rx queues")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The link modes that sfp_parse_support() detects are stored in the
'modes' bitmap. There is no reason to make an exception for 1000Base-PX
or 1000Base-BX10.

Fixes: 03145864 ("sfp: support 1G BiDi (eg, FiberStore SFP-GE-BX) modules")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kunihiko Hayashi says:

====================
fixup AVE ethernet driver

This series adds fixup for AVE ethernet driver that includes increse of
descriptors, replacing macro for linux-next, and adding missing author
information.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add missing MODULE_AUTHOR of ave driver and an entry to MAINTAINERS.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 26a4676f ("arm64: mm: define NET_IP_ALIGN to 0"),
AVE controller affects this modification because the controller forces
to ignore lower 2bits of buffer start address, and make 2-byte headroom,
that is, data reception starts from (buffer + 2).

This patch defines AVE_FRAME_HEADROOM macro as hardware-specific value,
and replaces NET_IP_ALIGN with it.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To improve performance, this increases Rx descriptor to 256, Tx descriptor
to 64, and adjusts NAPI weight to NAPI_POLL_WEIGHT.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) ARM64 JIT fixes for subprog handling from Daniel Borkmann.

 2) Various sparc64 JIT bug fixes (fused branch convergance, frame
    pointer usage detection logic, PSEODU call argument handling).

 3) Fix to use BH locking in nf_conncount, from Taehee Yoo.

 4) Fix race of TX skb freeing in ipheth driver, from Bernd Eckstein.

 5) Handle return value of TX NAPI completion properly in lan743x
    driver, from Bryan Whitehead.

 6) MAC filter deletion in i40e driver clears wrong state bit, from
    Lihong Yang.

 7) Fix use after free in rionet driver, from Pan Bian.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (53 commits)
  s390/qeth: fix length check in SNMP processing
  net: hisilicon: remove unexpected free_netdev
  rapidio/rionet: do not free skb before reading its length
  i40e: fix kerneldoc for xsk methods
  ixgbe: recognize 1000BaseLX SFP modules as 1Gbps
  i40e: Fix deletion of MAC filters
  igb: fix uninitialized variables
  netfilter: nf_tables: deactivate expressions in rule replecement routine
  lan743x: Enable driver to work with LAN7431
  tipc: fix lockdep warning during node delete
  lan743x: fix return value for lan743x_tx_napi_poll
  net: via: via-velocity: fix spelling mistake "alignement" -> "alignment"
  qed: fix spelling mistake "attnetion" -> "attention"
  net: thunderx: fix NULL pointer dereference in nic_remove
  sctp: increase sk_wmem_alloc when head->truesize is increased
  firestream: fix spelling mistake: "Inititing" -> "Initializing"
  net: phy: add workaround for issue where PHY driver doesn't bind to the device
  usbnet: ipheth: fix potential recvmsg bug and recvmsg bug 2
  sparc: Adjust bpf JIT prologue for PSEUDO calls.
  bpf, doc: add entries of who looks over which jits
  ...

Pull Xtensa fixes from Max Filippov:

 - fix kernel exception on userspace access to a currently disabled
   coprocessor

 - fix coprocessor data saving/restoring in configurations with multiple
   coprocessors

 - fix ptrace access to coprocessor data on configurations with multiple
   coprocessors with high alignment requirements

* tag 'xtensa-20181128' of git://github.com/jcmvbkbc/linux-xtensa:
  xtensa: fix coprocessor part of ptrace_{get,set}xregs
  xtensa: fix coprocessor context offset definitions
  xtensa: enable coprocessors that are being flushed

Jeff Kirsher says:

====================
Intel Wired LAN Driver Fixes 2018-11-28

This series contains fixes to igb, ixgbe and i40e.

Yunjian Wang from Huawei resolves a variable that could potentially be
NULL before it is used.

Lihong fixes an i40e issue which goes back to 4.17 kernels, where
deleting any of the MAC filters was causing the incorrect syncing for
the PF.

Josh Elsasser caught that there were missing enum values in the link
capabilities for x550 devices, which was preventing link for 1000BaseLX
SFP modules.

Jan fixes the function header comments for XSK methods.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The response for a SNMP request can consist of multiple parts, which
the cmd callback stages into a kernel buffer until all parts have been
received. If the callback detects that the staging buffer provides
insufficient space, it bails out with error.
This processing is buggy for the first part of the response - while it
initially checks for a length of 'data_len', it later copies an
additional amount of 'offsetof(struct qeth_snmp_cmd, data)' bytes.

Fix the calculation of 'data_len' for the first part of the response.
This also nicely cleans up the memcpy code.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for net:

1) Disable BH while holding list spinlock in nf_conncount, from
   Taehee Yoo.

2) List corruption in nf_conncount, also from Taehee.

3) Fix race that results in leaving around an empty list node in
   nf_conncount, from Taehee Yoo.

4) Proper chain handling for inactive chains from the commit path,
   from Florian Westphal. This includes a selftest for this.

5) Do duplicate rule handles when replacing rules, also from Florian.

6) Remove net_exit path in xt_RATEEST that results in splat, from Taehee.

7) Possible use-after-free in nft_compat when releasing extensions.
   From Florian.

8) Memory leak in xt_hashlimit, from Taehee.

9) Call ip_vs_dst_notifier after ipv6_dev_notf, from Xin Long.

10) Fix cttimeout with udplite and gre, from Florian.

11) Preserve oif for IPv6 link-local generated traffic from mangle
    table, from Alin Nastac.

12) Missing error handling in masquerade notifiers, from Taehee Yoo.

13) Use mutex to protect registration/unregistration of masquerade
    extensions in order to prevent a race, from Taehee.

14) Incorrect condition check in tree_nodes_free(), also from Taehee.

15) Fix chain counter leak in rule replacement path, from Taehee.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The net device ndev is freed via free_netdev when failing to register
the device. The control flow then jumps to the error handling code
block. ndev is used and freed again. Resulting in a use-after-free bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb is freed via dev_kfree_skb_any, however, skb->len is read then. This
may result in a use-after-free bug.

Fixes: e6161d64 ("rapidio/rionet: rework driver initialization and removal")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One method, xsk_umem_setup, had an incorrect kernel doc
description, which has been corrected.

Also fixes small typos found in the comments.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Pull btrfs fixes from David Sterba:
 "Some of these bugs are being hit during testing so we'd like to get
  them merged, otherwise there are usual stability fixes for stable
  trees"

* tag 'for-4.20-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: relocation: set trans to be NULL after ending transaction
  Btrfs: fix race between enabling quotas and subvolume creation
  Btrfs: send, fix infinite loop due to directory rename dependencies
  Btrfs: ensure path name is null terminated at btrfs_control_ioctl
  Btrfs: fix rare chances for data loss when doing a fast fsync
  btrfs: Always try all copies when reading extent buffers

Pull spi fixes from Mark Brown:
 "A few driver specific fixes here, nothing big or that stands out for
  anyone other than the driver users.

  The omap2-mcspi fix is for issues that started showing up with a
  change in defconfig in this release to make cpuidle get turned on by
  default"

* tag 'spi-fix-v4.20-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: omap2-mcspi: Add missing suspend and resume calls
  spi: mediatek: use correct mata->xfer_len when in fifo transfer
  spi: uniphier: fix incorrect property items

Add the two 1000BaseLX enum values to the X550's check for 1Gbps modules,
allowing the core driver code to establish a link over this SFP type.

This is done by the out-of-tree driver but the fix wasn't in mainline.

Fixes: e23f3336 ("ixgbe: Fix 1G and 10G link stability for X550EM_x SFP+”)
Fixes: 6a14ee0c ("ixgbe: Add X550 support function pointers")
Signed-off-by: Josh Elsasser <jelsasser@appneta.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Pull kvm fixes from Paolo Bonzini:
 "Bugfixes, many of them reported by syzkaller and mostly predating the
  merge window"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  kvm: svm: Ensure an IBPB on all affected CPUs when freeing a vmcb
  kvm: mmu: Fix race in emulated page table writes
  KVM: nVMX: vmcs12 revision_id is always VMCS12_REVISION even when copied from eVMCS
  KVM: nVMX: Verify eVMCS revision id match supported eVMCS version on eVMCS VMPTRLD
  KVM: nVMX/nSVM: Fix bug which sets vcpu->arch.tsc_offset to L1 tsc_offset
  x86/kvm/vmx: fix old-style function declaration
  KVM: x86: fix empty-body warnings
  KVM: VMX: Update shared MSRs to be saved/restored on MSR_EFER.LMA changes
  KVM: x86: Fix kernel info-leak in KVM_HC_CLOCK_PAIRING hypercall
  KVM: nVMX: Fix kernel info-leak when enabling KVM_CAP_HYPERV_ENLIGHTENED_VMCS more than once
  svm: Add mutex_lock to protect apic_access_page_done on AMD systems
  KVM: X86: Fix scan ioapic use-before-initialization
  KVM: LAPIC: Fix pv ipis use-before-initialization
  KVM: VMX: re-add ple_gap module parameter
  KVM: PPC: Book3S HV: Fix handling for interrupted H_ENTER_NESTED

In __i40e_del_filter function, the flag __I40E_MACVLAN_SYNC_PENDING for
the PF state is wrongly set for the VSI. Deleting any of the MAC filters
has caused the incorrect syncing for the PF. Fix it by setting this state
flag to the intended PF.

CC: stable <stable@vger.kernel.org>
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the variable 'phy_word' may be used uninitialized.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

There is no expression deactivation call from the rule replacement path,
hence, chain counter is not decremented. A few steps to reproduce the
problem:

   %nft add table ip filter
   %nft add chain ip filter c1
   %nft add chain ip filter c1
   %nft add rule ip filter c1 jump c2
   %nft replace rule ip filter c1 handle 3 accept
   %nft flush ruleset

<jump c2> expression means immediate NFT_JUMP to chain c2.
Reference count of chain c2 is increased when the rule is added.

When rule is deleted or replaced, the reference counter of c2 should be
decreased via nft_rule_expr_deactivate() which calls
nft_immediate_deactivate().

Splat looks like:
[  214.396453] WARNING: CPU: 1 PID: 21 at net/netfilter/nf_tables_api.c:1432 nf_tables_chain_destroy.isra.38+0x2f9/0x3a0 [nf_tables]
[  214.398983] Modules linked in: nf_tables nfnetlink
[  214.398983] CPU: 1 PID: 21 Comm: kworker/1:1 Not tainted 4.20.0-rc2+ #44
[  214.398983] Workqueue: events nf_tables_trans_destroy_work [nf_tables]
[  214.398983] RIP: 0010:nf_tables_chain_destroy.isra.38+0x2f9/0x3a0 [nf_tables]
[  214.398983] Code: 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 8e 00 00 00 48 8b 7b 58 e8 e1 2c 4e c6 48 89 df e8 d9 2c 4e c6 eb 9a <0f> 0b eb 96 0f 0b e9 7e fe ff ff e8 a7 7e 4e c6 e9 a4 fe ff ff e8
[  214.398983] RSP: 0018:ffff8881152874e8 EFLAGS: 00010202
[  214.398983] RAX: 0000000000000001 RBX: ffff88810ef9fc28 RCX: ffff8881152876f0
[  214.398983] RDX: dffffc0000000000 RSI: 1ffff11022a50ede RDI: ffff88810ef9fc78
[  214.398983] RBP: 1ffff11022a50e9d R08: 0000000080000000 R09: 0000000000000000
[  214.398983] R10: 0000000000000000 R11: 0000000000000000 R12: 1ffff11022a50eba
[  214.398983] R13: ffff888114446e08 R14: ffff8881152876f0 R15: ffffed1022a50ed6
[  214.398983] FS:  0000000000000000(0000) GS:ffff888116400000(0000) knlGS:0000000000000000
[  214.398983] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  214.398983] CR2: 00007fab9bb5f868 CR3: 000000012aa16000 CR4: 00000000001006e0
[  214.398983] Call Trace:
[  214.398983]  ? nf_tables_table_destroy.isra.37+0x100/0x100 [nf_tables]
[  214.398983]  ? __kasan_slab_free+0x145/0x180
[  214.398983]  ? nf_tables_trans_destroy_work+0x439/0x830 [nf_tables]
[  214.398983]  ? kfree+0xdb/0x280
[  214.398983]  nf_tables_trans_destroy_work+0x5f5/0x830 [nf_tables]
[ ... ]

Fixes: bb7b40ae ("netfilter: nf_tables: bogus EBUSY in chain deletions")
Reported by: Christoph Anton Mitterer <calestyo@scientia.net>
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=914505
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201791Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

This driver was designed to work with both LAN7430 and LAN7431.
The only difference between the two is the LAN7431 has support
for external phy.

This change adds LAN7431 to the list of recognized devices
supported by this driver.

Updates for v2:
    changed 'fixes' tag to match defined format

fixes: 23f0703c ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We see the following lockdep warning:

[ 2284.078521] ======================================================
[ 2284.078604] WARNING: possible circular locking dependency detected
[ 2284.078604] 4.19.0+ #42 Tainted: G            E
[ 2284.078604] ------------------------------------------------------
[ 2284.078604] rmmod/254 is trying to acquire lock:
[ 2284.078604] 00000000acd94e28 ((&n->timer)#2){+.-.}, at: del_timer_sync+0x5/0xa0
[ 2284.078604]
[ 2284.078604] but task is already holding lock:
[ 2284.078604] 00000000f997afc0 (&(&tn->node_list_lock)->rlock){+.-.}, at: tipc_node_stop+0xac/0x190 [tipc]
[ 2284.078604]
[ 2284.078604] which lock already depends on the new lock.
[ 2284.078604]
[ 2284.078604]
[ 2284.078604] the existing dependency chain (in reverse order) is:
[ 2284.078604]
[ 2284.078604] -> #1 (&(&tn->node_list_lock)->rlock){+.-.}:
[ 2284.078604]        tipc_node_timeout+0x20a/0x330 [tipc]
[ 2284.078604]        call_timer_fn+0xa1/0x280
[ 2284.078604]        run_timer_softirq+0x1f2/0x4d0
[ 2284.078604]        __do_softirq+0xfc/0x413
[ 2284.078604]        irq_exit+0xb5/0xc0
[ 2284.078604]        smp_apic_timer_interrupt+0xac/0x210
[ 2284.078604]        apic_timer_interrupt+0xf/0x20
[ 2284.078604]        default_idle+0x1c/0x140
[ 2284.078604]        do_idle+0x1bc/0x280
[ 2284.078604]        cpu_startup_entry+0x19/0x20
[ 2284.078604]        start_secondary+0x187/0x1c0
[ 2284.078604]        secondary_startup_64+0xa4/0xb0
[ 2284.078604]
[ 2284.078604] -> #0 ((&n->timer)#2){+.-.}:
[ 2284.078604]        del_timer_sync+0x34/0xa0
[ 2284.078604]        tipc_node_delete+0x1a/0x40 [tipc]
[ 2284.078604]        tipc_node_stop+0xcb/0x190 [tipc]
[ 2284.078604]        tipc_net_stop+0x154/0x170 [tipc]
[ 2284.078604]        tipc_exit_net+0x16/0x30 [tipc]
[ 2284.078604]        ops_exit_list.isra.8+0x36/0x70
[ 2284.078604]        unregister_pernet_operations+0x87/0xd0
[ 2284.078604]        unregister_pernet_subsys+0x1d/0x30
[ 2284.078604]        tipc_exit+0x11/0x6f2 [tipc]
[ 2284.078604]        __x64_sys_delete_module+0x1df/0x240
[ 2284.078604]        do_syscall_64+0x66/0x460
[ 2284.078604]        entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 2284.078604]
[ 2284.078604] other info that might help us debug this:
[ 2284.078604]
[ 2284.078604]  Possible unsafe locking scenario:
[ 2284.078604]
[ 2284.078604]        CPU0                    CPU1
[ 2284.078604]        ----                    ----
[ 2284.078604]   lock(&(&tn->node_list_lock)->rlock);
[ 2284.078604]                                lock((&n->timer)#2);
[ 2284.078604]                                lock(&(&tn->node_list_lock)->rlock);
[ 2284.078604]   lock((&n->timer)#2);
[ 2284.078604]
[ 2284.078604]  *** DEADLOCK ***
[ 2284.078604]
[ 2284.078604] 3 locks held by rmmod/254:
[ 2284.078604]  #0: 000000003368be9b (pernet_ops_rwsem){+.+.}, at: unregister_pernet_subsys+0x15/0x30
[ 2284.078604]  #1: 0000000046ed9c86 (rtnl_mutex){+.+.}, at: tipc_net_stop+0x144/0x170 [tipc]
[ 2284.078604]  #2: 00000000f997afc0 (&(&tn->node_list_lock)->rlock){+.-.}, at: tipc_node_stop+0xac/0x19
[...}

The reason is that the node timer handler sometimes needs to delete a
node which has been disconnected for too long. To do this, it grabs
the lock 'node_list_lock', which may at the same time be held by the
generic node cleanup function, tipc_node_stop(), during module removal.
Since the latter is calling del_timer_sync() inside the same lock, we
have a potential deadlock.

We fix this letting the timer cleanup function use spin_trylock()
instead of just spin_lock(), and when it fails to grab the lock it
just returns so that the timer handler can terminate its execution.
This is safe to do, since tipc_node_stop() anyway is about to
delete both the timer and the node instance.

Fixes: 6a939f36 ("tipc: Auto removal of peer down node instance")
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The lan743x driver, when under heavy traffic load, has been noticed
to sometimes hang, or cause a kernel panic.

Debugging reveals that the TX napi poll routine was returning
the wrong value, 'weight'. Most other drivers return 0.
And call napi_complete, instead of napi_complete_done.

Additionally when creating the tx napi poll routine.
Changed netif_napi_add, to netif_tx_napi_add.

Updates for v3:
    changed 'fixes' tag to match defined format

Updates for v2:
use napi_complete, instead of napi_complete_done in
    lan743x_tx_napi_poll
use netif_tx_napi_add, instead of netif_napi_add for
    registration of tx napi poll routine

fixes: 23f0703c ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The text in array velocity_gstrings contains a spelling mistake,
rename rx_frame_alignement_errors to rx_frame_alignment_errors.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>