- 07 Jul, 2011 40 commits
-
-
Andre Silva authored
Signed-off-by:
Andre Silva <andre.silva@freescale.com> Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de>
-
Fabio Estevam authored
Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
-
Fabio Estevam authored
On mx27_3ds board there is a l4f00242t03 LCD that is controlled via CSPI1. Add support for CSPI1 and LCD. Signed-off-by:
-
Dinh Nguyen authored
Adds initial low power suspend functionality to MX51. Supports "mem" and "standby" modes. Tested on mx51-babbage. Signed-off-by:
Dinh Nguyen <Dinh.Nguyen@freescale.com> Tested-by:
Arnaud Patard <arnaud.patard@rtp-net.org> Tested-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
-
Fabio Estevam authored
On MX1, MX21 and MX27 each GPIO port has an address space of 256 bytes. Fix the iosize for these platforms. Tested on a mx27_3ds board that can boot fine after this change. Cc: Shawn Guo <shawn.guo@freescale.com> Signed-off-by:
-
Fabio Estevam authored
Signed-off-by:
-
Fabio Estevam authored
Signed-off-by:
-
Andre Silva authored
Signed-off-by:
-
Andre Silva authored
Signed-off-by:
-
Andre Silva authored
Signed-off-by:
-
Andre Silva authored
Signed-off-by:
-
Andre Silva authored
Signed-off-by:
-
Shawn Guo authored
The patch converts mxc tzic interrupt controller to use generic irq chip. Signed-off-by:
-
Shawn Guo authored
It adds LED2 on mx28evk board as heartbeat trigger for diagnostic purpose. Signed-off-by:
-
Fabio Estevam authored
Signed-off-by:
-
Fabio Estevam authored
Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Shawn Guo authored
The patch adds following configurations to enable build of mx23evk and mx28evk in defconfig. CONFIG_MACH_MX23EVK CONFIG_MACH_MX28EVK Signed-off-by:
-
Sascha Hauer authored
Conflicts: arch/arm/mach-imx/mach-mx31_3ds.c arch/arm/mach-imx/mach-scb9328.c Signed-off-by: -
Sascha Hauer authored
CONFIG_ARCH_* are deprecated, so remove one user. Signed-off-by: -
Fabio Estevam authored
On the i.MX SPI driver the chipselect pins can be of the following types: - internal: when the chipselect pin is used as a dedicated CS pin of the CSPI controller - GPIO: a generic GPIO can be used as a chipselect funtion On the mx27_3ds the SPI2 chip select is a GPIO, so don't annotate 'internal' in the chip select definition. Signed-off-by:
-
Fabio Estevam authored
Use the standard gpio_to_irq function instead of a dedicated IRQ_GPIOx macro. Signed-off-by:
-
Fabio Estevam authored
Place the UART gpio initialization inside the scb9328_init function as it is done on other i.MX boards. Signed-off-by:
-
H Hartley Sweeten authored
Signed-off-by:
H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Sascha Hauer <kernel@pengutronix.de> Signed-off-by:
-
Fabio Estevam authored
As no flag is passed into UART0 platform data, pass NULL argument when registering UART0. Signed-off-by:
-
Sascha Hauer authored
There are several occurences where MXC_INTERNAL_IRQ is assumed to be the start of the gpio interrupts. It was never meant this way. Replace these with gpio_to_irq. Signed-off-by:
-
Sascha Hauer authored
This becomes meaningless in subsequent patches. Signed-off-by: -
Sascha Hauer authored
This becomes meaningless in subsequent patches. Signed-off-by: -
Sascha Hauer authored
CONFIG_ARCH_* are deprecated, so remove one user. Signed-off-by: -
Sascha Hauer authored
since we now can include all soc specific headers at once we do not need the ifdeffery anymore. Signed-off-by: -
Sascha Hauer authored
All soc specific header have proper namespace now and thus can be included at once. Signed-off-by: -
Sascha Hauer authored
We have a clocksource which renders CLOCK_TICK_RATE useless. Define it to a bogus value to get rid of some ifdeffery. Signed-off-by: -
Sascha Hauer authored
Signed-off-by: -
Uwe Kleine-König authored
This allows to move the led definition to .init.rodata. Signed-off-by:
-
Uwe Kleine-König authored
This gets rid of per machine struct platform_device definitions and allows to move the platform data and led definition to .init.rodata. Signed-off-by:
-
Uwe Kleine-König authored
This gets rid of per machine struct platform_device definitions and allows to move the platform data and led definition to .init.rodata. Signed-off-by:
-
Fabio Estevam authored
Instead of using gpio_request followed by gpio_direction_output use gpio_request_array when requesting multiple pins. Also fixed the location of the delay for the reset and make the BABBAGE_USB_PHY_RESET to toggle. Signed-off-by:
-
Fabio Estevam authored
The USB PHY Reset GPIO can be configured in the same place as the other GPIOs. While at it rename the pin as BABBAGE_USB_PHY_RESET to make clearer its purpose. Signed-off-by:
-
Troy Kisky authored
", o" was used for ", 0" ", 17" was used for ", 7 | 0x10" Signed-off-by:
Troy Kisky <troy.kisky@boundarydevices.com> Signed-off-by:
-
Sascha Hauer authored
dmaengine expects the maxburst parameter in words, not bytes. The imxdma driver and its users do this wrong. Fix this. As a side note the imx-pcm-dma-mx2 driver was 'fixed' to work with imx-dma. This broke the driver with imx-sdma support which correctly takes the maxburst parameter in words. This patch puts the sdma based sound back to work. Signed-off-by: -
Lothar Waßmann authored
The clock from which the I2C timing is derived is the ipg_perclk not ipg_clk. I2C bus frequency was lower by a factor of ~8 due to the clock divider calculation being based on 66.5MHz IPG clock while the bus actually uses 8MHz ipg_perclk. Kernel version: 3.0.0-rc2 branch 'imx-for-next' of git://git.pengutronix.de/git/imx/linux-2.6Signed-off-by:
Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by:
-
