- 26 Jan, 2020 12 commits
-
-
Chin-Yen Lee authored
Net-detect is an option of wowlan to allow the device to be woken up from suspend mode when configured network is detected. When user enables net-detect and lets the device enter suspend state, wowlan firmware will periodically scan until beacon or probe response of configured networks are received. Between two scans, wowlan firmware keeps wifi chip in idle mode to reduce power consumption. If configured networks are detected, wowlan firmware will trigger resume process. Signed-off-by:
Chin-Yen Lee <timlee@realtek.com> Signed-off-by:
Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Chin-Yen Lee authored
Pattern match is an option of wowlan to allow the device to be woken up from suspend mode when receiving packets matched user-designed patterns. The patterns are written into hardware cam in suspend flow if users have set up them. If packets matched designed pattern are received, wowlan firmware will get an interrupt and then wake up the device. Signed-off-by:
-
Chin-Yen Lee authored
Wake on WLAN(wowlan) is a feature which allows devices to be woken up from suspend state through wlan events. When user enables wowlan feature and then let the device enter suspend state, wowlan firmware will be loaded by the driver and periodically monitors wifi packets. Power consumption of wifi chip will be reduced in this state. If wowlan firmware detects that specific wlan event happens, it will issue wakeup signal to trigger resume process. Driver will load normal firmware and let wifi chip return to the original state. Currently supported wlan events include receiving magic packet, rekey packet and deauth packet, and disconnecting from AP. Signed-off-by:
-
Chin-Yen Lee authored
Driver used to download normal firmware only, but some devices support wowlan and require to download wowlan firmware when system suspends. So modify rtw_load_firmware() and its callback to allow driver to download both normal and wowlan firmware. Signed-off-by:
-
Yan-Hsuan Chuang authored
Some devices need to configure interface/HCI related reigsters in power on flow. Add interface_cfg for HCI for the settings. The driver only supports RTL8822BE/RTL8822CE now, and since RTL8822BE does not need to configure PCIE, the configuration is only added for RTL8822CE. Without it, some of the RTL8822CE device can crash and disconnected to host in suspend/wowlan mode. Signed-off-by:
Tzu-En Huang <tehuang@realtek.com> Signed-off-by:
-
Chin-Yen Lee authored
When PCI trx rings are reset, the DMA engine should also be reset. Otherswise, the rx_tag of rx flow is not synchronous to hw. Remove DMA reset when rtw_pci_start() as we added it in rtw_pci_setup(). Signed-off-by:
Chris Chiu <chiu@endlessm.com> Signed-off-by:
-
Chin-Yen Lee authored
When skbs queued for each TX ring are relased in PCI stop flow, the ring index should be reset at the same time. Signed-off-by:
-
Nathan Chancellor authored
Clang warns: ../drivers/net/wireless/intersil/hostap/hostap_ap.c:2511:3: warning: misleading indentation; statement is not part of the previous 'if' [-Wmisleading-indentation] if (sta->tx_supp_rates & WLAN_RATE_5M5) ^ ../drivers/net/wireless/intersil/hostap/hostap_ap.c:2509:2: note: previous statement is here if (sta->tx_supp_rates & WLAN_RATE_2M) ^ 1 warning generated. This warning occurs because there is a space before the tab on this line. Remove it so that the indentation is consistent with the Linux kernel coding style and clang no longer warns. Fixes: ff1d2767 ("Add HostAP wireless driver.") Link: https://github.com/ClangBuiltLinux/linux/issues/813Signed-off-by:Nathan Chancellor <natechancellor@gmail.com> Reviewed-by:
Nick Desaulniers <ndesaulniers@google.com> Signed-off-by:
-
Maital Hahn authored
In order to support authentication of equals peers, need to save RX Broadcast key per peer (on top of 1 TX broadcast key and unicast key per peer). Signed-off-by:
Maital Hahn <maitalm@ti.com> Acked-by:
Guy Mishol <guym@ti.com> Signed-off-by:
Hari Nagalla <hnagalla@gmail.com> Signed-off-by:
-
Ganapathi Bhat authored
Remove Nishant Sarmukadam from Maintainer list, as he is no longer working in NXP. Signed-off-by:
Ganapathi Bhat <ganapathi.bhat@nxp.com> Signed-off-by:
-
Brian Norris authored
Before commit 1e58252e ("mwifiex: Fix heap overflow in mmwifiex_process_tdls_action_frame()"), mwifiex_process_tdls_action_frame() already had too many magic numbers. But this commit just added a ton more, in the name of checking for buffer overflows. That seems like a really bad idea. Let's make these magic numbers a little less magic, by (a) factoring out 'pos[1]' as 'ie_len' (b) using 'sizeof' on the appropriate source or destination fields where possible, instead of bare numbers (c) dropping redundant checks, per below. Regarding redundant checks: the beginning of the loop has this: if (pos + 2 + pos[1] > end) break; but then individual 'case's include stuff like this: if (pos > end - 3) return; if (pos[1] != 1) return; Note that the second 'return' (validating the length, pos[1]) combined with the above condition (ensuring 'pos + 2 + length' doesn't exceed 'end'), makes the first 'return' (whose 'if' can be reworded as 'pos > end - pos[1] - 2') redundant. Rather than unwind the magic numbers there, just drop those conditions. Fixes: 1e58252e ("mwifiex: Fix heap overflow in mmwifiex_process_tdls_action_frame()") Signed-off-by:
Brian Norris <briannorris@chromium.org> Signed-off-by:
-
Kalle Valo authored
Merge tag 'iwlwifi-next-for-kalle-2020-01-11' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next First set of patches intended for v5.6 * Support new versions of the FTM FW APIs; * Fix an old bug in D3 (WoWLAN); * A couple of fixes/improvements in the receive-buffers code; * Fix in the debugging where we were skipping one TXQ; * Support new version of the beacon template FW API; * Print some extra information when the driver is loaded; * Some debugging infrastructure (aka. yoyo) updates; * Support for a new HW version; * Second phase of device configuration work started; * Some clean-ups;
-
- 13 Jan, 2020 2 commits
-
-
Geert Uytterhoeven authored
Use the print_hex_dump_debug() helper, instead of open-coding the same operations. Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Geert Uytterhoeven authored
Remove unused fields, copied from the Sun LANCE driver eons ago. Signed-off-by:
-
- 12 Jan, 2020 11 commits
-
-
Jakub Kicinski authored
Linus Walleij says: ==================== IXP4xx networking cleanups This is a patch series which jams together Arnds and mine cleanups for the IXP4xx networking. I also have patches for device tree support but that requires more elaborate work, this series is some of mine and some of Arnds patches that is a good foundation for his multiplatform work and my device tree work. These are for application to the networking tree so that can be taken in one separate sweep. I have tested the patches for a bit using zeroday builds and some boots on misc IXP4xx devices and haven't run into any major problems. We might find some new stuff as a result from the new compiler coverage. I had to depromote enabling compiler coverage at one point in the v2 set because it depended on other patches making the code more generic. The change in v3 was simply dropping one offending patch hardcoding base addresses into the driver. The change in v4 drops a stable@ tag that was unnecessary. This v5 is a rebase of the v4 patch set on top of net-next. ==================== Signed-off-by: -
Linus Walleij authored
Use the netdevice struct device .parent field when calling dma_pool_create(): the .dma_coherent_mask and .dma_mask pertains to the bus device on the hardware (platform) bus in this case, not the struct device inside the network device. This makes the pool allocation work. Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Linus Walleij authored
In order to probe this ethernet interface from the device tree all physical MMIO regions must be passed as resources. Begin this rewrite by first passing the port base address as a resource for all platforms using this driver, remap it in the driver and avoid using any reference of the statically mapped virtual address in the driver. Signed-off-by:
-
Linus Walleij authored
Simplify and correct a bunch of messages using printk directly to use the netdev_* macros. I have not changed all of them, just the low-hanging fruit. Signed-off-by:
-
Linus Walleij authored
Use "ndev" for the struct net_device and "dev" for the struct device in probe() and remove(). Add the local "dev" pointer for later use in refactoring. Take this opportunity to fix inverse christmas tree coding style. Signed-off-by:
-
Linus Walleij authored
The IXP4xx driver was initializing the MDIO bus before even probing, in the callbacks supposed to be used for setting up the module itself, and with the side effect of trying to register the MDIO bus as soon as this module was loaded or compiled into the kernel whether the device was discovered or not. This does not work with multiplatform environments. To get rid of this: set up the MDIO bus from the probe() callback and remove it in the remove() callback. Rename the probe() and remove() calls to reflect the most common conventions. Since there is a bit of checking for the ethernet feature to be present in the MDIO registering function, making the whole module not even be registered if we can't find an MDIO bus, we need something similar: register the MDIO bus when the corresponding ethernet is probed, and return -EPROBE_DEFER on the other interfaces until this happens. If no MDIO bus is present on any of the registered interfaces we will eventually bail out. None of the platforms I've seen has e.g. MDIO on EthB and only uses EthC, there is always a Ethernet hardware on the NPE (B, C) that has the MDIO bus, we just might have to wait for it. Signed-off-by:
-
Arnd Bergmann authored
The platform data is needed to compile the driver as standalone, so move it to a global location along with similar files. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Arnd Bergmann authored
The ixp46x ptp driver has a somewhat unusual setup, where the ptp driver and the ethernet driver are in different directories but access the same registers that are defined a platform specific header file. Moving everything into drivers/net/ makes it look more like most other ptp drivers and allows compile-testing this driver on other targets. Signed-off-by:
-
Arnd Bergmann authored
The ixp4xx_hss driver needs the platform data definition and the system clock rate to be compiled. Move both into a new platform_data header file. This is a prerequisite for compile testing, but turning on compile testing requires further patches to isolate the SoC headers. Signed-off-by:
-
Arnd Bergmann authored
Change the driver to use portable integer types to avoid warnings during compile testing: drivers/net/wan/ixp4xx_hss.c:863:21: error: cast to 'u32 *' (aka 'unsigned int *') from smaller integer type 'int' [-Werror,-Wint-to-pointer-cast] memcpy_swab32(mem, (u32 *)((int)skb->data & ~3), bytes / 4); ^ drivers/net/wan/ixp4xx_hss.c:979:12: error: incompatible pointer types passing 'u32 *' (aka 'unsigned int *') to parameter of type 'dma_addr_t *' (aka 'unsigned long long *') [-Werror,-Wincompatible-pointer-types] &port->desc_tab_phys))) ^~~~~~~~~~~~~~~~~~~~ include/linux/dmapool.h:27:20: note: passing argument to parameter 'handle' here dma_addr_t *handle); ^ Signed-off-by: -
Jonathan Lemon authored
On modern hardware with a large number of cpus and using XDP, the current MSIX limit is insufficient. Bump the limit in order to allow more queues. Signed-off-by:
Jonathan Lemon <jonathan.lemon@gmail.com> Reviewed-by:
Jack Wang <jinpu.wang@cloud.ionos.com> Reviewed-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
- 11 Jan, 2020 15 commits
-
-
David S. Miller authored
Huazhong Tan says: ==================== net: hns3: add some misc update about reset issue This series includes some misc update relating to reset issue. [patch 1/7] & [patch 2/7] splits hclge_reset()/hclgevf_reset() into two parts: preparing and rebuilding. Since the procedure of FLR should be separated out from the reset task([patch 3/7 & patch 3/7]), then the FLR's processing can reuse these codes. pci_error_handlers.reset_prepare() is void type function, so [patch 6/7] & [patch 7/7] factor some codes related to PF function reset to make the preparing done before .reset_prepare() return. BTW, [patch 5/7] enlarges the waiting time of reset for matching the hardware's. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Huazhong Tan authored
hclge_reset_prepare_down() is only used to inform VF that PF is going to do function reset, then using hclge_func_reset_sync_vf() in hclge_reset_prepare_wait() to query whether VF is ready before asserting PF function reset. To make the code more readable, this patch uses a new function hclge_function_reset_notify_vf() to do this job. Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
-
Huazhong Tan authored
When synchronizes with VFs fail before PF function reset, PF driver should go on its function reset, otherwise it can not run normally anymore. So, hclge_func_reset_sync_vf() should not affect the processing of PF reset, this patch modifies its return type to void. Signed-off-by:
-
Huazhong Tan authored
When the load of firmware is high, its reset task may takes more time(which will be as long as 35 seconds). So this patch modifies HCLGE_RESET_WAIT_CNT to match the firmware's. Signed-off-by:
-
Huazhong Tan authored
Currently, the actual work of VF FLR is handled in the reset task, which is asynchronous. So in some case, if the preparing and rebuilding are not done, then the VF FLR will trigger some problems, for example, makes hardware go into chaos. So this patch separates the process of VF FLR from reset task, and adds a semaphore to serialize this reset and others. When FLR's preparing fails, if there has other higher level reset pending or failing times less than the HCLGE_FLR_RETRY_CNT, this preparing should be retried, otherwise it will get into a wrong state. BTW, while the hardware reports misc interrupt during pcie_flr(), the driver can not receive this interrupt anymore, so disable it when hclgevf_flr_prepare() return, and re-enable it when enter hclgevf_flr_done(). Avoid declaring internal function hclgevf_enable_vector(), this patch also moves its definition forward, and removes unused enum hnae3_flr_state. Signed-off-by:
-
Huazhong Tan authored
Currently, the actual work of PF FLR is handled in the reset task, which is asynchronous. So in some case, if the preparing and rebuilding are not done, then the PF FLR will trigger some problems, for example, makes hardware go into chaos. So this patch separates the process of PF FLR from reset task, and adds a semaphore to serialize this reset and others. When FLR's preparing fails, if there has other higher level reset pending or failing times less than the HCLGE_FLR_RETRY_CNT, this preparing should be retried, otherwise PF and its VF may get into wrong state. BTW, while the hardware reports misc interrupt during pcie_flr(), the driver can not receive this interrupt anymore, so disable it when hclge_flr_prepare() return, and re-enable it when enter hclge_flr_done(). Signed-off-by:
-
Huazhong Tan authored
hclgevf_reset() is a little bloated, and the process of VF FLR will be separated from the reset task later. So this patch splits hclgevf_reset() into hclgevf_reset_prepare() and hclge_reset_rebuild(), then FLR can also reuse these two functions. Also moves HNAE3_UP_CLIENT into hclgevf_reset_stack(). Signed-off-by:
-
Huazhong Tan authored
hclge_reset() is a little bloated, and the process of PF FLR will be separated from the reset task later. So this patch splits hclge_reset() into hclge_reset_prepare() and hclge_reset_rebuild(), then FLR can also reuse these two functions. BTW, since hclge_clear_reset_cause() and hclge_reset_prepare_up() will not affect the device, so in hclge_reset_rebuild(), these functions are called without rtnl_lock. Signed-off-by:
-
YueHaibing authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/ethernet/sfc/mcdi_functions.c: In function 'efx_mcdi_ev_init': drivers/net/ethernet/sfc/mcdi_functions.c:79:28: warning: variable 'nic_data' set but not used [-Wunused-but-set-variable] commit 4438b587 ("sfc: move MCDI event queue management code") introduces this unused variable. Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
YueHaibing authored
Remove duplicated include. Signed-off-by:
Edward Cree <ecree@solarflare.com> Signed-off-by:
-
Jonathan Lemon authored
When running in XDP mode, pages come from the page pool, and should be freed back to the same pool or specifically detached. Currently, when the driver re-initializes, the page pool destruction is delayed forever since it thinks there are oustanding pages. Fixes: 322b87ca ("bnxt_en: add page_pool support") Signed-off-by:
Andy Gospodarek <gospo@broadcom.com> Signed-off-by:
-
David S. Miller authored
Jacob Keller says: ==================== devlink documentation refactor This series updates the devlink documentation, with a few primary goals * move all of the devlink documentation into a dedicated subfolder * convert that documentation to the reStructuredText format * merge driver-specific documentations into a single file per driver * add missing documentation, including per-driver and devlink generally For each driver, I took the time to review the code and add further documentation on the various features it currently supports. Additionally, I added new documentation files for some of the features such as devlink-dpipe, devlink-resource, and devlink-regions. Note for the region snapshot triggering, I kept that as a separate patch as that is based on work that has not yet been merged to net-next, and may change. I also improved the existing documentation for devlink-info and devlink-param by adding a bit more of an introduction when converting it to the rst format. ==================== Signed-off-by: -
Jacob Keller authored
Now that devlink regions can be triggered via DEVLINK_CMD_REGION_TRIGGER, document this in the devlink-region.rst file. Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Signed-off-by:
-
Jacob Keller authored
Primarily based on the DPIPE netdev conference paper, introduce a new file to document the dpipe interface. This likely needs further improvement, but is at least a good overall start. Signed-off-by:
-
Jacob Keller authored
Take the little bit of documentation for resources from various commit messages and combine it into a new devlink-resource.rst file. This could probably be expanded on even further by someone with more knowledge of how the devlink resources work. Signed-off-by:
-
