In order to support GPIO config changes direct these to the generic pinctrl.
This also requires an adjust of the return code for unsupported parameter
otherwise gpiod_configure_flags wont work as expected.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Since commit 0de70495 ("pinctrl: bcm2835: Add support for
generic pinctrl binding") this driver is capable to use the generic
interface. So declare this accordingly.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The UFS_RESET macro serves no purpose on QCS404, remove it.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add documentation for slew rate.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add slew rate support for SAM9X60 pin controller.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add device tree binding for SAM9X60 pin controller.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add documentation for at91 pin controller banks.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add compatibles for SAM9X60 pin controller.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add drive strength support for SAM9X60 pin controller.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

SAM9X60 uses high and low drive strengths. To implement this, in
at91_pinctrl_mux_ops::set_drivestrength and
at91_pinctrl_mux_ops::get_drivestrength we need bit numbers of
drive strengths (1 for low, 2 for high), thus change the code to
allow the usage of drive strength bit numbers.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add the pinctrl driver support for i.MX8MM.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Acked-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

In the original code, some function names begin with "ingenic_gpio_",
and some with "gpio_ingenic_". For the sake of uniform style,
all of them are changed to the beginning of "ingenic_gpio_".
Signed-off-by: Zhou Yanjie <zhouyanjie@cduestc.edu.cn>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add mmc2 for JZ4770 and JZ4780:
According to the datasheet, both JZ4770 and JZ4780 have mmc2. But this
part of the original code is missing. It is worth noting that JZ4770's
mmc2 supports 8bit mode while JZ4780's does not, so we added the
corresponding code for both models.

Add nemc-wait for JZ4770 and JZ4780:
Both JZ4770 and JZ4780 have a nemc-wait pin. But this part of the
original code is missing.

Add mac for JZ4770:
JZ4770 have a mac. But this part of the original code is missing.
Signed-off-by: Zhou Yanjie <zhouyanjie@cduestc.edu.cn>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Delete uart4 and i2c3/4 from JZ4770:
According to the datasheet, only JZ4780 have uart4 and i2c3/4. So we
remove it from the JZ4770 code and add a section corresponding the JZ4780.

Fix bugs in i2c0/1:
The pin number was wrong in the original code.

Fix bugs in uart2:
JZ4770 and JZ4780 have different uart2 pins. So the original section JZ4770
has been modified and the corresponding section of JZ4780 has been added.

Fix bugs in mmc0:
JZ4770 and JZ4780 assigned different pins to mmc0's 4~7 data lines. So the
original section JZ4770 has been modified and the corresponding section of
JZ4780 has been added.

Fix bugs in mmc1:
JZ4770's mmc1 has 8bit mode, while JZ4780 doesn't. So the original
section JZ4770 has been modified and the corresponding section of
JZ4780 has been added.

Fix bugs in nemc:
JZ4770's nemc has 16bit mode, while JZ4780 doesn't. So the original section
JZ4770 has been modified and the corresponding section of JZ4780 has been
added. And add missing cs2~5 groups for JZ4770 and JZ4780.

Fix bugs in cim:
JZ4770's cim has 12bit mode, while JZ4780 doesn't. So the original
section JZ4770 has been modified and the corresponding section of
JZ4780 has been added.

Fix bugs in lcd:
Both JZ4770 and JZ4780 lcd should be 24bit instead of 32bit.
Signed-off-by: Zhou Yanjie <zhouyanjie@cduestc.edu.cn>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

So that we could use the generic "pwm" for two or more pins, e.g

	pwm0_pmux: pwm0-pmux {
		groups = "PWM0", "PWM1";
		function = "pwm";
	};
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge tag 'sh-pfc-for-v5.1-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel

pinctrl: sh-pfc: Updates for v5.1

  - Add TMU pin groups on R-Car E3,
  - Miscellaneous fixes and cleanups.

There is no need to have the 'sgpio' variable static since new
value always be assigned before use it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The main goal of the change is to remove .pin_config_dbg_parse_modify
callback before a driver with its support appears. So far the in-kernel
interface did not attract any users since its introduction 5 years ago.

Originally .pin_config_dbg_parse_modify callback and the associated
'pinconf-config' debugfs file were introduced in commit f07512e6
("pinctrl/pinconfig: add debug interface"), a short description of
'pinconf-config' usage for debugging can be expressed this way:

Write to 'pinconf-config' (see pinconf_dbg_config_write() function):

% echo -n modify $map_type $device_name $state_name $pin_name $config > \
	/sys/kernel/debug/pinctrl/$pinctrl/pinconf-config

It supposes to update a global (therefore single!) 'pinconf_dbg_conf'
variable with an alternative setting, the arguments should match
an existing pinconf device and some registered pinctrl mapping 'map':

* $map_type is either 'config_pin' or 'config_group', it should match
  'map->type' value of PIN_MAP_TYPE_CONFIGS_PIN or
   PIN_MAP_TYPE_CONFIGS_GROUP accordingly,
* $device_name should match 'map->dev_name' string value,
* $state_name should match 'map->name' string value,
* $pin_name should match 'map->data.configs.group_or_pin' string value,

If all above has matched, then $config is a new value to be set by calling
pinconfops->pin_config_dbg_parse_modify(pctldev, config, matched_config).

After a successful write into 'pinconf-config' a user can read the file
to get information about that single modified pin configuration.

The fact is .pin_config_dbg_parse_modify callback has never been defined
in 'struct pinconf_ops' of any pinconf driver, thus an actual modification
of a pin or group state on any present pinconf controller does not happen,
and it declares that all related code is no more than dead code.

I discovered the issue while attempting to add .pin_config_dbg_parse_modify
support in some drivers and found that too short 'MAX_NAME_LEN' set by

  drivers/pinctrl/pinconf.c:372:#define MAX_NAME_LEN 15

is practically insufficient to store a regular pinctrl device name,
which are like 'e6060000.pin-controller-sh-pfc' or pin names like
'MX6QDL_PAD_ENET_REF_CLK', thus it is another indicator that the code
is barely usable, insufficiently tested and unprepossessing.

Of course it might be possible to increase MAX_NAME_LEN, and then add
.pin_config_dbg_parse_modify callbacks to the drivers, but the whole
idea of such a limited debug option looks inviable. A more flexible
way to functionally substitute the original approach is to implicitly
or explicitly use pinctrl_select_state() function whenever needed.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Laurent Meunier <laurent.meunier@st.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The change adds explicit inclusion of linux/pinctrl/machine.h header
to the only needed pinctrl-madera-core.c file, and therefore inclusion
of pinctrl/machine.h header from pinctrl/pinconf.h can be removed.

The change is preparatory to a follow-up reversal of commit f07512e6
("pinctrl/pinconfig: add debug interface").
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add binding doc imx8mm pinctrl driver.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Acked-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Returning -EAGAIN is no longer supported by pin_config_group_set()
since ad42fc6c ("pinctrl: rip out the direct pinconf API")

Remove the relevant section from the documentation.
Signed-off-by: Ramon Fried <ramon.fried@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Now that spmi-gpio is a proper hierarchical IRQ chip, and all in-tree
users of device tree have been updated, we can now drop the hack that
was introduced to disassociate the old Linux virq if a hwirq mapping
already exists. That patch was introduced to not break git bisect for
any existing boards.

Driver was tested using gpio-keys and iadc/vadc on the LG Nexus 5
(hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

qpnpint_irq_domain_map did not validate the IRQ type and this can cause
IRQs to not work as expected if an unsupported type (such as
IRQ_TYPE_NONE) is passed in. Now that spmi-gpio is a hierarchical IRQ
controller, and all device tree bindings have been updated, add
additional validation to the type field.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.

This change was not tested on any hardware but the same change was
tested on qcom-pm8941.dtsi using a LG Nexus 5 (hammerhead) phone with
no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.

This change was not tested on any hardware but the same change was
tested on qcom-pm8941.dtsi using a LG Nexus 5 (hammerhead) phone with
no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.

This change was not tested on any hardware but the same change was
tested on qcom-pm8941.dtsi using a LG Nexus 5 (hammerhead) phone with
no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.

This change was not tested on any hardware but the same change was
tested on qcom-pm8941.dtsi using a LG Nexus 5 (hammerhead) phone with
no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.

This change was not tested on any hardware but the same change was
tested on qcom-pm8941.dtsi using a LG Nexus 5 (hammerhead) phone with
no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it. Code was tested on the LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

spmi-gpio did not have any irqchip support so consumers of this in
device tree would need to call gpio[d]_to_irq() in order to get the
proper IRQ on the underlying PMIC. IRQ chips in device tree should
be usable from the start without the consumer having to make an
additional call to get the proper IRQ on the parent. This patch adds
hierarchical IRQ chip support to the spmi-gpio code to correct this
issue.

Driver was tested using the volume buttons (via gpio-keys) on the LG
Nexus 5 (hammerhead) phone with the following two configurations.

volume-up {
        interrupts-extended = <&pm8941_gpios 2 IRQ_TYPE_EDGE_BOTH>;
        ...
};

volume-up {
        gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
        ...
};

Both configurations now show that spmi-gpio is the IRQ domain and that
the IRQ is setup in a hierarchy.

$ grep volume_up /proc/interrupts
 72:          6          0  spmi-gpio   1 Edge      volume_up

$ cat /sys/kernel/debug/irq/irqs/72
handler:  handle_edge_irq
device:   (null)
status:   0x00000403
            _IRQ_NOPROBE
istate:   0x00000000
ddepth:   0
wdepth:   0
dstate:   0x02400203
            IRQ_TYPE_EDGE_RISING
            IRQ_TYPE_EDGE_FALLING
            IRQD_ACTIVATED
            IRQD_IRQ_STARTED
node:     0
affinity: 0-3
effectiv:
domain:  :soc:spmi@fc4cf000:pm8941@0:gpios@c000
 hwirq:   0x1
 chip:    spmi-gpio
  flags:   0x4
             IRQCHIP_MASK_ON_SUSPEND
 parent:
    domain:  :soc:spmi@fc4cf000
     hwirq:   0xc100057
     chip:    pmic_arb
      flags:   0x4
                 IRQCHIP_MASK_ON_SUSPEND
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Check to see if the hwirq is already associated with another virq on
this IRQ domain. If so, then disassociate it before associating the
hwirq with the new virq.

This is a temporary hack that is needed in order to not break git
bisect for existing boards. The next patch in this series converts
spmi-gpio to be a hierarchical IRQ chip, then there are several patches
to update all of the device tree files, and finally this patch will be
reverted within the same patch series.

IRQs for spmi-gpio are all initially setup without an IRQ hierarchy
on pmic-arb when mfd/qcom-spmi-pmic.c is probed (via the
devm_of_platform_populate call) due to the interrupts property in
device tree. Once spmi-gpio is converted to be a hierarchical IRQ chip
in the next patch, existing users of gpio[d]_to_irq() will call
pmic_gpio_to_irq(), and that will use the new IRQ chip code in
spmi-gpio that sets up the IRQ in an IRQ hierarchy. The hwirq is now
associated with two Linux virqs and interrupts will not work as
expected. This patch corrects that issue.

Driver was tested using gpio-keys and iadc/vadc on the LG Nexus 5
(hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds the two new functions gpiochip_irq_domain_activate and
gpiochip_irq_domain_deactivate that can be used as the activate and
deactivate functions in the struct irq_domain_ops. This is for
situations where only gpiochip_{lock,unlock}_as_irq needs to be called.
SPMI and SSBI GPIO are two users that will initially use these
functions.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Convert the spmi-pmic-arb IRQ code to use the version 2 IRQ interface
in order to support hierarchical IRQ chips. This is necessary so that
spmi-gpio can be setup as a hierarchical IRQ chip with pmic-arb as the
parent. IRQ chips in device tree should be usable from the start without
the consumer having to make an additional call to gpio[d]_to_irq() to
get the proper IRQ on the parent.

The old qpnpint_irq_domain_map function would hardcode the handler as
handle_level_irq, however qpnpint_irq_set_type would later override the
handler. Properly set the handler when the IRQ is mapped. This new code
doesn't return an error for IRQ_TYPE_NONE and preserves the existing
behavior of using handle_level_irq since there are some broken device
tree bindings that need to be corrected first.

Driver was tested on a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

On the G12a, there is a new 'region' to handle the drive-strength.
This is optional since the older do not have this.

Fixes: 29ae0952 ("pinctrl: meson-g12a: add pinctrl driver support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Since Meson G12A SoC, Introduce new ao registers AO_RTI_PULL_UP_EN_REG
and AO_GPIO_O.

These bits of controlling output level are remapped to the new register
AO_GPIO_O, and the AO_GPIO_O_EN_N support only controlling output enable.

These bits of controlling pull enable are remapped to the new register
AO_RTI_PULL_UP_EN_REG, and the AO_RTI_PULL_UP_REG support only controlling
pull type(up/down).

The new layout of ao gpio/pull registers is as follows:
- AO_GPIO_O_EN_N        [offset: 0x9 << 2]
- AO_GPIO_I             [offset: 0xa << 2]
- AO_RTI_PULL_UP_REG    [offset: 0xb << 2]
- AO_RTI_PULL_UP_EN_REG [offset: 0xc << 2]
- AO_GPIO_O             [offset: 0xd << 2]

From above, we can see ao GPIO registers region has been separated by the
ao pull registers. In order to ensure the continuity of the region on
software, the ao GPIO and ao pull registers use the same base address, but
can be identified by the offset.

Fixes: 29ae0952 ("pinctrl: meson-g12a: add pinctrl driver support")
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

like pull-enable, pull should be optional has this region is available on
every controllers. Also, the g12a feature a new region "ds" for the
drive-strength

All this region thing is one big mess. I suspect that there is only one
big GPIO region with holes in it. All registers between the current
regions reads '0' so it is probably just spare space to handle more pins.

Since we need to continue to handle the existing controllers, switching to
one single region now would not simplify things. However, if more
organisation layouts and features keep on being added, we may have to look
at this again

Fixes: 3cd3c83f ("pinctrl: Add compatibles for Amlogic Meson G12A pin controllers")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Dont print every single iodelay register configuration - this is just
plain noise. Since this is useful debug information, just lower to debug
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>