- 25 Jul, 2013 40 commits
-
-
Hauke Mehrtens authored
commit 693026ef upstream. When b43 gets build into the kernel and it should use bcma we have to ensure that bcma was also build into the kernel and not as a module. In this patch this is also done for SSB, although you can not build b43 without ssb support for now. This fixes a build problem reported by Randy Dunlap in 5187EB95.2060605@infradead.org Reported-By:
Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Luiz Capitulino authored
commit 8c6bab4f upstream. balloon_page_dequeue() can return NULL. If it does for the first page being freed then leak_balloon() will create a scatter list with len=0. Which in turn seems to generate an invalid virtio request. I didn't get this in practice, I found it by code review. On the other hand, such an invalid virtio request will cause errors in QEMU and fill_balloon() also performs the same check implemented by this commit. This bug was introduced in e2250429. Signed-off-by:
Luiz Capitulino <lcapitulino@redhat.com> Acked-by:
Rafael Aquini <aquini@redhat.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Rusty Russell <rusty@rustcorp.com.au> Signed-off-by:
-
Reddy, Sreekanth authored
commit b0df96a0 upstream. Missing delay is not getting set properly. The reason is that it is not defined in the same file from where it is being invoked. The fix is to move the missing delay module parameter from mpt2sas_base.c to mpt2sas_scsh.c. Signed-off-by:
Sreekanth Reddy <Sreekanth.Reddy@lsi.com> Signed-off-by:
James Bottomley <JBottomley@Parallels.com> Signed-off-by:
-
Sreekanth Reddy authored
commit 48ba2efc upstream. When SCSI command is received with task attribute not set, set it to SIMPLE. Previously it is set to untagged. This causes the firmware to fail the commands. Signed-off-by:
-
Steffen Maier authored
commit 9edf7d75 upstream. Commit 64deb6ef "[SCSI] zfcp: Use status_read_buf_num provided by FCP channel" started using a value returned by the channel but only evaluated the value if the fabric link is up. Commit 8d88cf3f "[SCSI] zfcp: Update status read mempool" introduced mempool resizings based on the above value. On setting an FCP device online for the very first time since boot, a new zeroed adapter object is allocated. If the link is down, the number of status read requests remains zero. Since just the config data exchange is incomplete, we proceed with adapter open recovery. However, we unconditionally call mempool_resize with adapter->stat_read_buf_num == 0 in this case. This causes a kernel message "kernel BUG at mm/mempool.c:131!" in process "zfcperp<FCP-device-bus-ID>" with last function mempool_resize in Krnl PSW and zfcp_erp_thread in the Call Trace. Don't evaluate channel values which are invalid on link down. The number of status read requests is always valid, evaluated, and set to a positive minimum greater than zero. The adapter open recovery can proceed and the channel has status read buffers to inform us on a future link up event. While we are not aware of any other code path that could result in mempool resize attempts of size zero, we still also initialize the number of status read buffers to be posted to a static minimum number on adapter object allocation. Signed-off-by:
Steffen Maier <maier@linux.vnet.ibm.com> Signed-off-by:
-
Steffen Maier authored
commit 5fea4291 upstream. Commit 86a9668a "[SCSI] zfcp: support for hardware data router" reduced the initial block queue limits in the scsi_host_template to the absolute minimum and adjusted them later on. However, the adjustment was too late for the BSG devices of Scsi_Host and fc_host. Therefore, ioctl(..., SG_IO, ...) with request or response size > 4kB to a BSG device of an fc_host or a Scsi_Host fails with EINVAL. As a result, users of such ioctl such as HBA_SendCTPassThru() in libzfcphbaapi return with error HBA_STATUS_ERROR. Initialize the block queue limits in zfcp_scsi_host_template to the greatest common denominator (GCD). While we cannot exploit the slightly enlarged maximum request size with data router, this should be neglectible. Doing so also avoids running into trouble after live guest relocation (LGR) / migration from a data router FCP device to an FCP device that does not support data router. In that case, zfcp would figure out the new limits on adapter recovery, but the fc_host and Scsi_Host (plus in fact all sdevs) still exist with the old and now too large queue limits. It should also OK, not to use half the size as in the DIX case, because fc_host and Scsi_Host do not transport FCP requests including SCSI commands using protection data. Signed-off-by:
Martin Peschke <mpeschke@linux.vnet.ibm.com> Signed-off-by:
-
Daniel Hansel authored
commit f76ccaac upstream. FCP device remains in status ERP_FAILED when device is switched online or adapter recovery is triggered while link to SAN is down. When Exchange Configuration Data command returns the FSF status FSF_EXCHANGE_CONFIG_DATA_INCOMPLETE it aborts the exchange process. The only retries are done during the common error recovery procedure (i.e. max. 3 retries with 8sec sleep between) and remains in status ERP_FAILED with QDIO down. This commit reverts the commit 0df13847 (zfcp: Fix adapter activation on link down). When FSF status FSF_EXCHANGE_CONFIG_DATA_INCOMPLETE is received the adapter recovery will be finished without any retries. QDIO will be up now and status changes such as LINK UP will be received now. Signed-off-by:
Daniel Hansel <daniel.hansel@linux.vnet.ibm.com> Signed-off-by:
-
Mahesh Rajashekhara authored
commit c5bebd82 upstream. One of the customer had reported that the set of raid logical arrays will become unavailable (I/O offline) after a long hours of IO stress test. The OS wouldn`t be accessible afterwards and require a hard reset. This driver patch has a fix for race condition between the doorbell and the circular buffer. The driver is modified to do an extra read after clearing the doorbell in case there had been a completion posted during the small timing window. With this fix, we ran IO stress for ~13 days. There were no IO failures. Signed-off-by:
Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com> Signed-off-by:
-
Martin K. Petersen authored
commit 66c28f97 upstream. SATA drives located behind a SAS controller would incorrectly receive WRITE SAME commands. Tweak the heuristics so that: - If REPORT SUPPORTED OPERATION CODES is provided we will use that to choose between WRITE SAME(16), WRITE SAME(10) and disabled. This also fixes an issue with the old code which would issue WRITE SAME(10) despite the command not being whitelisted in REPORT SUPPORTED OPERATION CODES. - If REPORT SUPPORTED OPERATION CODES is not provided we will fall back to WRITE SAME(10) unless the device has an ATA Information VPD page. The assumption is that a SATL which is smart enough to implement WRITE SAME would also provide REPORT SUPPORTED OPERATION CODES. To facilitate the new heuristics scsi_report_opcode() has been modified to so we can distinguish between "operation not supported" and "RSOC not supported". Reported-by:
H. Peter Anvin <hpa@zytor.com> Tested-by:
Bernd Schubert <bernd.schubert@itwm.fraunhofer.de> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Sujith Manoharan authored
commit d3bcb7b2 upstream. ah->noise is maintained globally and not per-channel. This is updated in the reset() routine after the NF history has been filled for the *current channel*, just before switching to the new channel. There is no need to do it inside getnf(), since ah->noise must contain a value for the new channel. Signed-off-by:
Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by:
-
Sujith Manoharan authored
commit 696df785 upstream. The commits, "ath9k: Fix regression in channelwidth switch at the same channel" "ath9k: Fix invalid noisefloor reading due to channel update" attempted to fix noisefloor calibration when a channel switch happens due to HT20/HT40 bandwidth change. This is causing invalid readings resulting in messages like: "ath: phy16: NF[0] (-45) > MAX (-95), correcting to MAX". This results in an incorrect noise being used initially for reporting the signal level of received packets, until NF calibration is done and the history buffer is updated via the ANI timer, which happens much later. When a bandwidth change happens, it is appropriate to reset the internal history data for the channel. Do this correctly in the reset() routine by checking the "chanmode" variable. Signed-off-by:
-
Sujith Manoharan authored
commit 30d5b709 upstream. For AR9485 boards with XLNA, the default gpio config is not set correctly, fix this. Signed-off-by:
-
Gabor Juhos authored
commit 0847beb2 upstream. The code writes the default_power2 value into the TX field of the RFCSR50 register, however the condition in the if statement uses default_power1. Due to this, wrong TX power value might be written into the register. Use the correct value in the condition to fix the issue. Compile tested only. Signed-off-by:
Gabor Juhos <juhosg@openwrt.org> Acked-by:
Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by:
-
Gabor Juhos authored
commit 0a6f3a8e upstream. The current code uses the same index value both for the channel information array and for the TX power table. The index starts from 14, however the index of the TX power table must start from zero. Fix it, in order to get the correct TX power value for a given channel. The changes in rt61pci.c and rt73usb.c are compile tested only. Signed-off-by:
Stanislaw Gruszka <stf_xl@wp.pl> Acked-by:
-
Baruch Siach authored
commit 1a33bd2b upstream. irq_of_parse_and_map() returns 0 on error, while the code checks for NO_IRQ. This breaks on platforms that have NO_IRQ != 0. Signed-off-by:
Baruch Siach <baruch@tkos.co.il> Signed-off-by:
Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by:
-
Thomas Gleixner authored
commit 1f73a980 upstream. When the system switches from periodic to oneshot mode, the broadcast logic causes a possibility that a CPU which has not yet switched to oneshot mode puts its own clock event device into oneshot mode without updating the state and the timer handler. CPU0 CPU1 per cpu tickdev is in periodic mode and switched to broadcast Switch to oneshot mode tick_broadcast_switch_to_oneshot() cpumask_copy(tick_oneshot_broacast_mask, tick_broadcast_mask); broadcast device mode = oneshot Timer interrupt irq_enter() tick_check_oneshot_broadcast() dev->set_mode(ONESHOT); tick_handle_periodic() if (dev->mode == ONESHOT) dev->next_event += period; FAIL. We fail, because dev->next_event contains KTIME_MAX, if the device was in periodic mode before the uncontrolled switch to oneshot happened. We must copy the broadcast bits over to the oneshot mask, because otherwise a CPU which relies on the broadcast would not been woken up anymore after the broadcast device switched to oneshot mode. So we need to verify in tick_check_oneshot_broadcast() whether the CPU has already switched to oneshot mode. If not, leave the device untouched and let the CPU switch controlled into oneshot mode. This is a long standing bug, which was never noticed, because the main user of the broadcast x86 cannot run into that scenario, AFAICT. The nonarchitected timer mess of ARM creates a gazillion of differently broken abominations which trigger the shortcomings of that broadcast code, which better had never been necessary in the first place. Reported-and-tested-by:
Stehle Vincent-B46079 <B46079@freescale.com> Reviewed-by:
Stephen Boyd <sboyd@codeaurora.org> Cc: John Stultz <john.stultz@linaro.org>, Cc: Mark Rutland <mark.rutland@arm.com> Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1307012153060.4013@ionos.tec.linutronix.deSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Thomas Gleixner authored
commit 07bd1172 upstream. The recent implementation of a generic dummy timer resulted in a different registration order of per cpu local timers which made the broadcast control logic go belly up. If the dummy timer is the first clock event device which is registered for a CPU, then it is installed, the broadcast timer is initialized and the CPU is marked as broadcast target. If a real clock event device is installed after that, we can fail to take the CPU out of the broadcast mask. In the worst case we end up with two periodic timer events firing for the same CPU. One from the per cpu hardware device and one from the broadcast. Now the problem is that we have no way to distinguish whether the system is in a state which makes broadcasting necessary or the broadcast bit was set due to the nonfunctional dummy timer installment. To solve this we need to keep track of the system state seperately and provide a more detailed decision logic whether we keep the CPU in broadcast mode or not. The old decision logic only clears the broadcast mode, if the newly installed clock event device is not affected by power states. The new logic clears the broadcast mode if one of the following is true: - The new device is not affected by power states. - The system is not in a power state affected mode - The system has switched to oneshot mode. The oneshot broadcast is controlled from the deep idle state. The CPU is not in idle at this point, so it's safe to remove it from the mask. If we clear the broadcast bit for the CPU when a new device is installed, we also shutdown the broadcast device when this was the last CPU in the broadcast mask. If the broadcast bit is kept, then we leave the new device in shutdown state and rely on the broadcast to deliver the timer interrupts via the broadcast ipis. Reported-and-tested-by:
-
NeilBrown authored
commit 7bb23c49 upstream. 1/ When an different between blocks is found, data is copied from one bio to the other. However bv_len is used as the length to copy and this could be zero. So use r10_bio->sectors to calculate length instead. Using bv_len was probably always a bit dubious, but the introduction of bio_advance made it much more likely to be a problem. 2/ When preparing some blocks for sync, we don't set BIO_UPTODATE except on bios that we schedule for a read. This ensures that missing/failed devices don't confuse the loop at the top of sync_request write. Commit 8be185f2 "raid10: Use bio_reset()" removed a loop which set BIO_UPTDATE on all appropriate bios. So we need to re-add that flag. These bugs were introduced in 3.10, so this patch is suitable for 3.10-stable, and can remove a potential for data corruption. Reported-by:
Brassow Jonathan <jbrassow@redhat.com> Signed-off-by:
NeilBrown <neilb@suse.de> Signed-off-by:
-
NeilBrown authored
commit 78eaa0d4 upstream. 1/ If a RAID10 is being reshaped to a fewer number of devices and is stopped while this is ongoing, then when the array is reassembled the 'mirrors' array will be allocated too small. This will lead to an access error or memory corruption. 2/ A sanity test for a reshaping RAID10 array is restarted is slightly incorrect. Due to the first bug, this is suitable for any -stable kernel since 3.5 where this code was introduced. Signed-off-by:
-
NeilBrown authored
commit 13765120 upstream. The recent comment: commit 7e83ccbe md/raid10: Allow skipping recovery when clean arrays are assembled Causes raid10 to skip a recovery in certain cases where it is safe to do so. Unfortunately it also causes a reshape to be skipped which is never safe. The result is that an attempt to reshape a RAID10 will appear to complete instantly, but no data will have been moves so the array will now contain garbage. (If nothing is written, you can recovery by simple performing the reverse reshape which will also complete instantly). Bug was introduced in 3.10, so this is suitable for 3.10-stable. Signed-off-by:
-
Fabio Estevam authored
commit 5c78dfe8 upstream. SGTL5000_PLL_FRAC_DIV_MASK is used to mask bits 0-10 (11 bits in total) of register CHIP_PLL_CTRL, so fix the mask to accomodate all this bit range. Reported-by:
Oskar Schirmer <oskar@scara.com> Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
Mark Brown <broonie@linaro.org> Signed-off-by:
-
Takashi Iwai authored
commit 57118571 upstream. snd_pcm_stop() must be called in the PCM substream lock context. Acked-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit 61be2b9a upstream. snd_pcm_stop() must be called in the PCM substream lock context. Acked-by:
-
Shane Huang authored
commit b996ac90 upstream. To add AMD CZ SMBus controller device ID. [bhelgaas: drop pci_ids.h update] Signed-off-by:
Shane Huang <shane.huang@amd.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Reviewed-by:
Tejun Heo <tj@kernel.org> Reviewed-by:
Jean Delvare <khali@linux-fr.org> Signed-off-by:
-
Mark Langsdorf authored
commit ddfef5de upstream. Increase the retry count for the hard reset function to 100 but shorten the time out period to 500 ms. See the comment for ahci_highbank_hardreset for the reasons why those vaulues were chosen. Signed-off-by:
Mark Langsdorf <mark.langsdorf@calxeda.com> Signed-off-by:
-
Seth Heasley authored
commit c7e8695b upstream. This patch adds the IDE-mode SATA DeviceIDs for the Intel Coleto Creek PCH. Signed-off-by:
Seth Heasley <seth.heasley@intel.com> Signed-off-by:
-
Tejun Heo authored
commit 7a87718d upstream. For some reason, a lot of port-multipliers have issues with softreset. SIMG [34]7x series port-multipliers have been quite erratic in this regard. I recall that it was better with some firmware revisions and the current list of quirks worked fine for a while. I think it got worse with later firmwares or maybe my test coverage wasn't good enough. Anyways, HPA is reporting that his 3726 setup suffers SRST failures and then the PMP gets confused and fails to probe the last port. The hope was that we try to stick to the standard as much as possible and soonish the PMPs and their firmwares will improve in quality, so the quirk list was kept to minimum. Well, it seems like that's never gonna happen. Let's set NO_SRST for all [34]7x PMPs so that whatever remaining userbase of the device suffer the least. Maybe we should do the same for 57xx's but unfortunately I don't have any device left to test and I'm not even sure 57xx's have ever been made widely available, so let's leave those alone for now. Signed-off-by:
-
Sergei Shtylyov authored
commit d0887c43 upstream. There are some SATA controllers which have both devices 0 and 1 but this module just zeroes out taskfile and sets then ATA_TFLAG_DEVICE (not sure that's needed) which could lead to a wrong device being selected just before issuing command. Thus we should call ata_tf_init() which sets up the device register value properly, like all other users of ata_exec_internal() do... Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
-
Guenter Roeck authored
commit 41fa9a94 upstream. NCT6775 does not support alarms for fans 4 and 5. Drop the attributes. Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Guenter Roeck authored
commit b1d2bff6 upstream. Driver displays wrong alarms for temperature attributes. Turns out that temperature alarm bits are not fixed, but determined by temperature source mapping. To fix the problem, walk through the temperature sources to determine the correct alarm bit associated with a given attribute. Signed-off-by:
-
Takashi Iwai authored
commit 5be1efb4 upstream. snd_pcm_stop() must be called in the PCM substream lock context. Signed-off-by:
-
Takashi Iwai authored
commit 60478295 upstream. snd_pcm_stop() must be called in the PCM substream lock context. Signed-off-by:
-
Takashi Iwai authored
commit cc7282b8 upstream. snd_pcm_stop() must be called in the PCM substream lock context. Signed-off-by:
-
Takashi Iwai authored
commit 46f6c1aa upstream. snd_pcm_stop() must be called in the PCM substream lock context. Acked-by:
-
Takashi Iwai authored
commit 9538aa46 upstream. snd_pcm_stop() must be called in the PCM substream lock context. Acked-by:
Clemens Ladisch <clemens@ladisch.de> Signed-off-by:
-
Takashi Iwai authored
commit 5b9ab3f7 upstream. snd_pcm_stop() must be called in the PCM substream lock context. Signed-off-by:
-
Takashi Iwai authored
commit 256ca9c3 upstream. We've got bug reports that the module loading stuck on Debian system with 3.10 kernel. The debugging session revealed that the initial registration of OSS sequencer clients stuck at module loading time, which involves again with request_module() at the init phase. This is triggered only by special --install stuff Debian is using, but it's still not good to have such loops. As a workaround, call the registration part asynchronously. This is a better approach irrespective of the hang fix, in anyway. Reported-and-tested-by:
Philipp Matthias Hahn <pmhahn@pmhahn.de> Signed-off-by:
-
Aaron Plattner authored
commit d52392b1 upstream. Vendor ID 0x10de0060 is used by a yet-to-be-named GPU chip. Reviewed-by:
Andy Ritger <aritger@nvidia.com> Signed-off-by:
Aaron Plattner <aplattner@nvidia.com> Signed-off-by:
-
Takashi Iwai authored
commit 0c055b34 upstream. add_control_with_pfx() in hda_generic.c assumes a shorter name string for the control element, and this resulted in the truncation of the long but valid string like "Headphone Surround Switch" in the middle. This patch aligns the max size to the actual limit of snd_ctl_elem_id, 44. Signed-off-by:
-
Takashi Iwai authored
commit d045c5dc upstream. Some VIA codecs like VT1708S have Mic boost amps in the mic pins but they aren't exposed in the capability bits. In the past driver code, we override the pin caps and create mic boost controls forcibly. While transition to the generic parser, we lost the mic boost controls although the pin caps are still overridden, because the generic parser code checks the widget caps, too. So this patch adds a new helper function to allow the override of the given widget capability bits, and makes VIA codecs driver to add the missing input-amp capability bit. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59861Signed-off-by:
-
