Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

As we provide a list of all objects that will be accessed from the
batchbuffer, we can build a lut of the handles associated with those
objects for this invocation and use that to avoid the overhead of
looking up those objects again for every relocation.

The cost of building and searching a small hash table is much less than
that of acquiring a spinlock, searching a radix tree and manipulating an
atomic refcnt per relocation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

Don't post a downclocking task if the device is still active when the
idle timer fires. A pathological process could queue up several seconds
worth of processing and then go to sleep, during which time the idle
timer would kick in and downclock the GPU.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

... still causes a failure during suspend.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

Conflicts:
	drivers/gpu/drm/i915/i915_gem.c
	drivers/gpu/drm/i915/intel_dp.c

As we may try to power down the link at various times, it is not
necessarily still coupled with an encoder and so we must be careful not
to depend upon an operation that is only valid when the link is still
attached to a pipe.

Fixes regression in 5bddd17f.
Reported-and-tested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org [after applying 5bddd17f]

In order for bos to retire eventually, a request must be sent down the
ring. This is expected, for example, by occlusion queries for which mesa
will wait upon (whilst running glean) before issuing more batches and so
the normal activity upon the ring is suspended and we need to emit a
request to clear the idle ring.
Reported-by: Jinjin, Wang <jinjin.wang@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30380Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

I'm still seeing tiling corruption of PutImage and CopyArea (I think)
under mutter on pnv, so obviously the pipelining logic is deeply flawed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

Userspace should not have been declaring that it needed fenced GPU
access with gen4+ as those GPUs have no fenced commands, but to be on
the safe side it is easier to ignore userspace in case they did.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

The ability to save the hardware context upon powering down the render
clock through PWRCTXA is only available on a couple of gen4 chipsets.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

The workaround is hideous and we are using the STORE_DWORD on all other
generations on all other rings, so use for the gen5 render ring as
well.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

Linus Torvalds pointed out that our code was unbalanced when powering on
the panel with respect to the power off sequence in that we were failing
to restore the panel-fitter. The consequence of this would be that
across a simple DPMS off/on for a non-native mode, without an intervening
modeset, the panel fitter would remain disabled and the output would shift
on the panel.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

There's not much we can do here but hope for the best. However the first
failure happens quite frequently and if often remedied by the second
attempt to reset HEAD. So only print the error if that attempt also
fails.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=19802Reported-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org

Locally scope the crtc to where it is used.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

Immediate merge for the conflicting introduction of HAS_COHERENT_RINGS.

Conflicts:
	drivers/gpu/drm/i915/i915_dma.c
	include/drm/i915_drm.h

Otherwise we can't really fix the abi-braindeadness of forcing
libva to manually wait for rendering when switching rings. Which
in turn makes implementing hw semaphores a pointless exercise
(at least for ironlake).

[Also added the relaxed fencing param to explain the jump in
numbering - relaxed fencing is in -next.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

Add a missing NULL check and fix the wrong address passed to kunmap()
in i830_cleanup().

Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[danvet: added cc stable]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

We disabled this a while ago as it was inexplicably broken. However, it
now appears to work...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

The bulk of the change is to convert the growing list of rings into an
array so that the relationship between the rings and the semaphore sync
registers can be easily computed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

This will declare the machine wedged, but is better than truly wedging
the machine.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

Previously we enabled this for gen4, only to have to revert it due to it
causing a large number of spurious wakeups. Try again hoping that the
hardware has become more sane in the mean time...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

Let's see if we've successfully cleared up all the bugs from last
time...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

Magic numbers from the specs. This is supposed to allow the PLL some
variance to improve jitter performance and VCO headroom across
manufacturing and environmental variations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

... it's because setting the Pixel Multiply bits only takes effect once
the PLL is enabled and stable.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

... and do not just assume to always use pipe B.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

Fixes the modesetting on the secondary panel of the Libretto W100 and
presumably many more Ironlake laptops with SDVO LVDS displays.
Reported-and-tested-by: Matthew Willoughby <mattfredwill@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org

Use the hardware DDA to calculate the ratio with as much accuracy as is
possible.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org

If we leave the registers in a conflicting state then when we attempt
to teardown the active mode, we will not disable the pipes and planes
in the correct order -- leaving a plane reading from a disabled pipe and
possibly leading to undefined behaviour.
Reported-and-tested-by: Andy Whitcroft <apw@canonical.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=32078Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org

Conflicts:
	drivers/gpu/drm/i915/intel_drv.h

This workaround only applies to Ironlake.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org

The pipe is always set to 8BPC, but here we were leaving whatever
previous bits were set by the BIOS in place.
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org

* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (27 commits)
  Staging: rt2870: Add USB ID for Buffalo Airstation WLI-UC-GN
  staging: easycap needs smp_lock.h, fixes build error
  Staging: batman-adv: ensure that eth_type_trans gets linear memory
  Staging: batman-adv: Don't remove interface with spinlock held
  staging: brcm80211: updated maintainers contact information
  staging: fix winbond build, needs delay.h
  Staging: line6: fix up my fixup for some sysfs attribute permissions
  Staging: zram: fix up my fixup for some sysfs attribute permissions
  Staging: udlfb: fix up my fixup for some sysfs attribute permissions
  Staging: samsung-laptop: fix up my fixup for some sysfs attribute permissions
  Staging: iio: adis16220: fix up my fixup for some sysfs attribute permissions
  Staging: frontier: fix up my fixup for some sysfs attribute permissions
  Staging: asus_oled: fix up my fixup for some sysfs attribute permissions
  staging: spectra: fix build error
  Staging: intel_sst: fix memory leak
  Staging: rtl8712: signedness bug in init
  staging: rtl8187se: Change panic to warn when RF switch turned off
  staging: comedi: fix memory leak
  Staging: quickstart: free after input_unregister_device()
  Staging: speakup: free after input_unregister_device()
  ...

Merge branch 'driver-core-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6

* 'driver-core-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  uio: Change mail address of Hans J. Koch
  driver core: prune docs about device_interface
  driver core: the development tree has switched to git

* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  serial: mfd: adjust the baud rate setting
  TTY: open/hangup race fixup
  TTY: don't allow reopen when ldisc is changing
  NET: wan/x25, fix ldisc->open retval
  TTY: ldisc, fix open flag handling
  serial8250: Mark console as CON_ANYTIME

* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: fix autosuspend bug in usb-serial
  USB: ehci: disable LPM and PPCD for nVidia MCP89 chips
  USB: serial: ftdi_sio: Vardaan USB RS422/485 converter PID added
  USB: yurex: add .llseek fop to file_operations
  USB: ftdi_sio: Add ID for RT Systems USB-29B radio cable
  usb: musb: do not use dma for control transfers
  usb: musb: gadget: fix compilation warning
  usb: musb: clear RXCSR_AUTOCLEAR before PIO read
  usb: musb: unmap dma buffer when switching to PIO
  xhci: Don't let the USB core disable SuperSpeed ports.
  xhci: Setup array of USB 2.0 and USB 3.0 ports.
  xhci: Fix reset-device and configure-endpoint commands