This commit makes use of the axp209.dtsi file to define the
AXP209 PMIC. While here, define the rails that are enabled on
this board.

Tested checking the regulator voltage varies according to the
CPU frequency.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The SinA31s has a coaxial SPDIF output. Enable it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This adds the cpu-supply DT property to the cpu0 DT node needed by
the board to adapt the regulator voltage depending on the currently used
OPP.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This adds almost all operating points allowed for the A33 as defined by
fex files available at:
https://github.com/linux-sunxi/sunxi-boards/tree/master/sys_config/a33

There are more possible frequencies in this patch than there are in the
fex files because the fex files only give an interval of possible
frequencies for a given voltage. All supported frequencies are defined
in the original driver code in Allwinner vendor tree.

There are two missing frequencies though: 1104MHz and 1200MHz which
require the CPU to have 1.32V supplied, which is higher than the default
voltage.

Without all A33 boards defining the CPU regulator, we cannot have these
two frequencies as it would cause the CPU to try to run a higher
frequency without "overvolting" which is very likely to crash the CPU.

Therefore, these two frequencies must be enabled on a per-board basis.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The NextThing Co. CHIP has an AXP209 PMIC and can be power-supplied by
ACIN via the CHG-IN pin.

This enables the ACIN power supply subnode in the DT.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Sinlinx SinA33 has an AXP223 PMIC and an ACIN connector, thus, we
enable the ACIN power supply in its Device Tree.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The X-Powers AXP22X PMIC exposes the status of AC power supply.

This adds the AC power supply subnode for the AXP22X PMIC.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The X-Powers AXP20X PMIC exposes the status of AC power supply, the
current current and voltage supplied to the board by the AC power
supply.

This adds the AC power supply subnode for AXP20X PMIC.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

All dts files for the sunxi platform have been switched to the generic
pinconf bindings. As a result, the sunxi specific pinctrl macros are
no longer used.

Remove the #include entry with the following command:

    sed --follow-symlinks -i -e '/pinctrl\/sun4i-a10.h/D' \
	arch/arm/boot/dts/sun?i*.*

arch/arm/boot/dts/sun9i-a80.dtsi was then edited to remove the extra
empty line.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The old sunxi specific pinctrl bindings are deprecated, in favor of
the new generic pinconf bindings. Also, we are moving towards handling
GPIO pinmux settings that don't require extra bias or drive strength
settings to use the GPIO bindings only.

This patch removes the last instance of the sunxi specific pinctrl
bindings that use the pinctrl header by dropping the pinmux setting
for the audio codec's PA (external amplifier) control GPIO. The pin
is pulled down externally.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Mali GPU in the A33 has various operating frequencies used in the
Allwinner BSP.

Add them to our DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The operating-points-v2 binding gives a way to provide the OPP of the GPU.
Let's use it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>

The reserved memory bindings allow us to specify which memory areas our
buffers can be allocated from.

Let's use it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>

Add the needed node for DFVS on Sinovoip BPI-M2.
This add the axp221 under the p2wi node, the regulators and
the cpu-supply property for cpu0.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Beelink X2 has an on-board eMMC so add a node enabling
the mmc2 controller.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A20-OLinuXino-Micro has 3.5 mm sockets for headphone output and
microphone input.
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

add support for the NanoPi NEO Air H3 board from friendlyarm.com . This
board contains WiFi, Bluetooth, 8GB eMMC storage and 512 MB DDR3 ram.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Most of the GR8 DTSI is duplicated with the common sun5i DTSI, and some of
the extra nodes defined there actually apply to all of the sun5i family.

Move those into the common DTSI so that all SoCs can benefit from it, and
include the sun5i DTSI.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Some controllers found in the R8 DTSI actually apply to all of the sun5i
family. Move those into the common DTSI so that all SoCs can benefit from
it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Some controllers found in the A10s DTSI actually apply to all of the sun5i
family. Move those into the common DTSI so that all SoCs can benefit from
it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Some controllers found in the A13 DTSI actually apply to all of the sun5i
family. Move those into the common DTSI so that all SoCs can benefit from
it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The UART3 pin group for the CTS and RTS signals doesn't follow our usual
pattern. Rename it so that it matches.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

There's one UART2 pin group that can be used across all sun5i SoCs.
However, the A10s already has one pin group for that controller.

Change the index of the one in the A10s DTSI, and add the common one to
sun5i.dtsi
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Of the three simple framebuffer setups we have in the A10s, two of them can
be shared with the other SoCs from the sun5i family (LCD panel and
composite output).

However, the only one we cannot share is the HDMI, which is the first
listed in the A10s DTSI. In order to make it more logical and so that we
can share the framebuffer nodes in the common DTSI, reorder those nodes.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

One of the pins group for the EMAC can be used by all the SoCs of the sun5i
family, and as such can be moved to the common DTSI.

Unfortunately, this group is the second one we declare in our DT for now.
Make it the first one so that it's more logical and consistent with the
rest of our DTs before moving it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Pull networking fixes from David Miller:

 1) Fix double-free in batman-adv, from Sven Eckelmann.

 2) Fix packet stats for fast-RX path, from Joannes Berg.

 3) Netfilter's ip_route_me_harder() doesn't handle request sockets
    properly, fix from Florian Westphal.

 4) Fix sendmsg deadlock in rxrpc, from David Howells.

 5) Add missing RCU locking to transport hashtable scan, from Xin Long.

 6) Fix potential packet loss in mlxsw driver, from Ido Schimmel.

 7) Fix race in NAPI handling between poll handlers and busy polling,
    from Eric Dumazet.

 8) TX path in vxlan and geneve need proper RCU locking, from Jakub
    Kicinski.

 9) SYN processing in DCCP and TCP need to disable BH, from Eric
    Dumazet.

10) Properly handle net_enable_timestamp() being invoked from IRQ
    context, also from Eric Dumazet.

11) Fix crash on device-tree systems in xgene driver, from Alban Bedel.

12) Do not call sk_free() on a locked socket, from Arnaldo Carvalho de
    Melo.

13) Fix use-after-free in netvsc driver, from Dexuan Cui.

14) Fix max MTU setting in bonding driver, from WANG Cong.

15) xen-netback hash table can be allocated from softirq context, so use
    GFP_ATOMIC. From Anoob Soman.

16) Fix MAC address change bug in bgmac driver, from Hari Vyas.

17) strparser needs to destroy strp_wq on module exit, from WANG Cong.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
  strparser: destroy workqueue on module exit
  sfc: fix IPID endianness in TSOv2
  sfc: avoid max() in array size
  rds: remove unnecessary returned value check
  rxrpc: Fix potential NULL-pointer exception
  nfp: correct DMA direction in XDP DMA sync
  nfp: don't tell FW about the reserved buffer space
  net: ethernet: bgmac: mac address change bug
  net: ethernet: bgmac: init sequence bug
  xen-netback: don't vfree() queues under spinlock
  xen-netback: keep a local pointer for vif in backend_disconnect()
  netfilter: nf_tables: don't call nfnetlink_set_err() if nfnetlink_send() fails
  netfilter: nft_set_rbtree: incorrect assumption on lower interval lookups
  netfilter: nf_conntrack_sip: fix wrong memory initialisation
  can: flexcan: fix typo in comment
  can: usb_8dev: Fix memory leak of priv->cmd_msg_buffer
  can: gs_usb: fix coding style
  can: gs_usb: Don't use stack memory for USB transfers
  ixgbe: Limit use of 2K buffers on architectures with 256B or larger cache lines
  ixgbe: update the rss key on h/w, when ethtool ask for it
  ...

Pull more KVM updates from Radim Krčmář:
 "Second batch of KVM changes for the 4.11 merge window:

  PPC:
   - correct assumption about ASDR on POWER9
   - fix MMIO emulation on POWER9

  x86:
   - add a simple test for ioperm
   - cleanup TSS (going through KVM tree as the whole undertaking was
     caused by VMX's use of TSS)
   - fix nVMX interrupt delivery
   - fix some performance counters in the guest

  ... and two cleanup patches"

* tag 'kvm-4.11-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: nVMX: Fix pending events injection
  x86/kvm/vmx: remove unused variable in segment_base()
  selftests/x86: Add a basic selftest for ioperm
  x86/asm: Tidy up TSS limit code
  kvm: convert kvm.users_count from atomic_t to refcount_t
  KVM: x86: never specify a sample period for virtualized in_tx_cp counters
  KVM: PPC: Book3S HV: Don't use ASDR for real-mode HPT faults on POWER9
  KVM: PPC: Book3S HV: Fix software walk of guest process page tables

Pull documentation fixes from Jonathan Corbet:
 "A few fixes for the docs tree, including one for a 4.11 build
  regression"

* tag 'docs-4.11-fixes' of git://git.lwn.net/linux:
  Documentation/sphinx: fix primary_domain configuration
  docs: Fix htmldocs build failure
  doc/ko_KR/memory-barriers: Update control-dependencies section
  pcieaer doc: update the link
  Documentation: Update path to sysrq.txt

Pull staging/IIO driver fixes from Greg KH:
 "Here are a few small staging and IIO driver fixes for issues that
  showed up after the big set if changes you merged last week.

  Nothing major, just small bugs resolved in some IIO drivers, a lustre
  allocation fix, and some RaspberryPi driver fixes for reported
  problems, as well as a MAINTAINERS entry update.

  All of these have been in linux-next for a week with no reported
  issues"

* tag 'staging-4.11-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: fsl-mc: fix warning in DT ranges parser
  MAINTAINERS: Remove Noralf Trønnes as fbtft maintainer
  staging: vchiq_2835_arm: Make cache-line-size a required DT property
  staging: bcm2835/mmal-vchiq: unlock on error in buffer_from_host()
  staging/lustre/lnet: Fix allocation size for sv_cpt_data
  iio: adc: xilinx: Fix error handling
  iio: 104-quad-8: Fix off-by-one error when addressing flag register
  iio: adc: handle unknow of_device_id data

Pull crypto fixes from Herbert Xu:

 - vmalloc stack regression in CCM

 - Build problem in CRC32 on ARM

 - Memory leak in cavium

 - Missing Kconfig dependencies in atmel and mediatek

 - XTS Regression on some platforms (s390 and ppc)

 - Memory overrun in CCM test vector

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: vmx - Use skcipher for xts fallback
  crypto: vmx - Use skcipher for cbc fallback
  crypto: testmgr - Pad aes_ccm_enc_tv_template vector
  crypto: arm/crc32 - add build time test for CRC instruction support
  crypto: arm/crc32 - fix build error with outdated binutils
  crypto: ccm - move cbcmac input off the stack
  crypto: xts - Propagate NEED_FALLBACK bit
  crypto: api - Add crypto_requires_off helper
  crypto: atmel - CRYPTO_DEV_MEDIATEK should depend on HAS_DMA
  crypto: atmel - CRYPTO_DEV_ATMEL_TDES and CRYPTO_DEV_ATMEL_SHA should depend on HAS_DMA
  crypto: cavium - fix leak on curr if curr->head fails to be allocated
  crypto: cavium - Fix couple of static checker errors

Pull misc final vfs updates from Al Viro:
 "A few unrelated patches that got beating in -next.

  Everything else will have to go into the next window ;-/"

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  hfs: fix hfs_readdir()
  selftest for default_file_splice_read() infoleak
  9p: constify ->d_name handling

Pull more SCSI updates from James Bottomley:
 "This is the set of stuff that didn't quite make the initial pull and a
  set of fixes for stuff which did.

  The new stuff is basically lpfc (nvme), qedi and aacraid. The fixes
  cover a lot of previously submitted stuff, the most important of which
  probably covers some of the failing irq vectors allocation and other
  fallout from having the SCSI command allocated as part of the block
  allocation functions"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (59 commits)
  scsi: qedi: Fix memory leak in tmf response processing.
  scsi: aacraid: remove redundant zero check on ret
  scsi: lpfc: use proper format string for dma_addr_t
  scsi: lpfc: use div_u64 for 64-bit division
  scsi: mac_scsi: Fix MAC_SCSI=m option when SCSI=m
  scsi: cciss: correct check map error.
  scsi: qla2xxx: fix spelling mistake: "seperator" -> "separator"
  scsi: aacraid: Fixed expander hotplug for SMART family
  scsi: mpt3sas: switch to pci_alloc_irq_vectors
  scsi: qedf: fixup compilation warning about atomic_t usage
  scsi: remove scsi_execute_req_flags
  scsi: merge __scsi_execute into scsi_execute
  scsi: simplify scsi_execute_req_flags
  scsi: make the sense header argument to scsi_test_unit_ready mandatory
  scsi: sd: improve TUR handling in sd_check_events
  scsi: always zero sshdr in scsi_normalize_sense
  scsi: scsi_dh_emc: return success in clariion_std_inquiry()
  scsi: fix memory leak of sdpk on when gd fails to allocate
  scsi: sd: make sd_devt_release() static
  scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.
  ...

Fixes: 43a0c675 ("strparser: Stream parser for messages")
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for your net tree,
they are:

1) Missing check for full sock in ip_route_me_harder(), from
   Florian Westphal.

2) Incorrect sip helper structure initilization that breaks it when
   several ports are used, from Christophe Leroy.

3) Fix incorrect assumption when looking up for matching with adjacent
   intervals in the nft_set_rbtree.

4) Fix broken netlink event error reporting in nf_tables that results
   in misleading ESRCH errors propagated to userspace listeners.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull libnvdimm fixes from Dan Williams:
 "A fix and regression test case for nvdimm namespace label
  compatibility.

  Details:

   - An "nvdimm namespace label" is metadata on an nvdimm that
     provisions dimm capacity into a "namespace" that can host a block
     device / dax-filesytem, or a device-dax character device.

     A namespace is an object that other operating environment and
     platform firmware needs to comprehend for capabilities like booting
     from an nvdimm.

     The label metadata contains a checksum that Linux was not
     calculating correctly leading to other environments rejecting the
     Linux label.

   These have received a build success notification from the kbuild
   robot, and a positive test result from Nick who reported the problem"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  nfit, libnvdimm: fix interleave set cookie calculation
  tools/testing/nvdimm: make iset cookie predictable

Pull PCI fixes from Bjorn Helgaas:

 - fix NULL pointer dereferences in many DesignWare-based drivers due to
   refactoring error

 - fix Altera config write breakage due to my refactoring error

* tag 'pci-v4.11-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: altera: Fix TLP_CFG_DW0 for TLP write
  PCI: dwc: Fix crashes seen due to missing assignments

Pull parisc fixes and cleanups from Helge Deller:
 "Nothing really important in this patchset: fix resource leaks in error
  paths, coding style cleanups and code removal"

* 'parisc-4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Remove flush_user_dcache_range and flush_user_icache_range
  parisc: fix a printk
  parisc: ccio-dma: Handle return NULL error from ioremap_nocache
  parisc: Define access_ok() as macro
  parisc: eisa: Fix resource leaks in error paths
  parisc: eisa: Remove coding style errors

Pull Xtensa updates from Max Filippov:

 - clean up bootable image build targets: provide separate 'Image',
   'zImage' and 'uImage' make targets that only build corresponding
   image type. Make 'all' build all images appropriate for a platform

 - allow merging vectors code into .text section as a preparation step
   for XIP support

 - fix handling external FDT when the kernel is built without
   BLK_DEV_INITRD support

* tag 'xtensa-20170303' of git://github.com/jcmvbkbc/linux-xtensa:
  xtensa: allow merging vectors into .text section
  xtensa: clean up bootable image build targets
  xtensa: move parse_tag_fdt out of #ifdef CONFIG_BLK_DEV_INITRD

Pull ARM SoC late DT updates from Arnd Bergmann:
 "These updates have been kept in a separate branch mostly because they
  rely on updates to the respective clk drivers to keep the shared
  header files in sync.

  This includes two branches for arm64 dt updates, both following up on
  earlier changes for the same platforms that are already merged:

  Samsung:
   - add USB3 support in Exynos7
   - minor PM related updates

  Amlogic:
   - new machines: WeTek Set-top-boxes
   - various devices added to DT

  There are also a couple of bugfixes that trickled in since the start
  of the merge window:

   - The moxart_defconfig was not building the intended platform
   - CPU-hotplug was broken on ux500
   - Coresight was broken on Juno (never worked)"

* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
  ARM: deconfig: fix the moxart defconfig
  ARM: ux500: resume the second core properly
  arm64: dts: juno: update definition for programmable replicator
  arm64: dts: exynos: Add regulators for Vbus and Vbus-Boost
  arm64: dts: exynos: Add USB 3.0 controller node for Exynos7
  arm64: dts: exynos: Use macros for pinctrl configuration on Exynos7
  pinctrl: dt-bindings: samsung: Add Exynos7 specific pinctrl macro definitions
  arm64: dts: exynos: Add initial configuration for DISP clocks for TM2/TM2e
  ARM64: dts: meson-gxbb-p200: add ADC laddered keys
  ARM64: dts: meson: meson-gx: add the SAR ADC
  ARM64: dts: meson-gxl: add the pwm_ao_b pin
  ARM64: dts: meson-gx: add the missing pwm_AO_ab node
  clk: gxbb: fix CLKID_ETH defined twice
  ARM64: dts: meson-gxl: rename Nexbox A95x for consistency
  clk: gxbb: add the SAR ADC clocks and expose them
  dt-bindings: amlogic: Add WeTek boards
  ARM64: dts: meson-gxbb: Add support for WeTek Hub and Play
  dt-bindings: vendor-prefix: Add wetek vendor prefix
  ARM64: dts: meson-gxm: Rename q200 and q201 DT files for consistency
  ARM64: dts: meson-gx: Add HDMI HPD/DDC pinctrl nodes
  ...