This patch adds functions to configure mac, when flow control
and pause frame settings change.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes RSS feature, for non-TCP/UDP packets.
Signed-off-by: Khuong Dinh <kdinh@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch implements ndo_change_mtu() callback function that
enables mtu change.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for jumbo frame, by allocating
additional buffer (page) pool and configuring the hardware.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch configures classifier with the pagepool information.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a prepartion patch and adds xgene_enet_get_fpsel() helper
function to get buffer pool number.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As of commit 8f32b909
("net: ethernet: ti: davinci_cpdma: add set rate for a channel") the
ARM allmodconfig builds would fail modpost with:

ERROR: "cpdma_chan_set_weight" [drivers/net/ethernet/ti/ti_cpsw.ko] undefined!
ERROR: "cpdma_chan_get_rate" [drivers/net/ethernet/ti/ti_cpsw.ko] undefined!
ERROR: "cpdma_chan_get_min_rate" [drivers/net/ethernet/ti/ti_cpsw.ko] undefined!
ERROR: "cpdma_chan_set_rate" [drivers/net/ethernet/ti/ti_cpsw.ko] undefined!

Since these weren't declared as static, it is assumed they were
meant to be shared outside the file, and that modular build testing
was simply overlooked.

Fixes: 8f32b909 ("net: ethernet: ti: davinci_cpdma: add set rate for a channel")
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-omap@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-next-for-4.10-20161201' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
pull-request: can-next 2016-12-01

this is a pull request of 4 patches for net-next/master.

There are two patches by Chris Paterson for the rcar_can and rcar_canfd
device tree binding documentation. And a patch by Geert Uytterhoeven
that corrects the order of interrupt specifiers.

The fourth patch by Colin Ian King fixes a spelling error in the
kvaser_usb driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

stmmac_mdio_{read|write} and stmmac_mdio_{read|write}_gmac4 are not
enought different for being split.
The only differences between thoses two functions are shift/mask for
addr/reg/clk_csr.

This patch introduce a per platform set of variable for setting thoses
shift/mask and unify mdio read and write functions.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch simply rename regValue to value, like it was named in other
mdio functions.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As David Miller pointed out for for the previous patch, the whitespace
in some functions looks rather odd. This was caused by commit 6329da5f
("obsolete config in kernel source: USE_INTERNAL_TIMER"), which removed
some conditions but did not reindent the code.

This fixes the indentation in the file and removes extraneous whitespace
at the end of the lines and before tabs.

There are many other minor coding style problems in the driver, but I'm
not touching those here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix english in documentation, make documentation match reality, remove
options that were removed from code.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Couple conflicts resolved here:

1) In the MACB driver, a bug fix to properly initialize the
   RX tail pointer properly overlapped with some changes
   to support variable sized rings.

2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
   overlapping with a reorganization of the driver to support
   ACPI, OF, as well as PCI variants of the chip.

3) In 'net' we had several probe error path bug fixes to the
   stmmac driver, meanwhile a lot of this code was cleaned up
   and reorganized in 'net-next'.

4) The cls_flower classifier obtained a helper function in
   'net-next' called __fl_delete() and this overlapped with
   Daniel Borkamann's bug fix to use RCU for object destruction
   in 'net'.  It also overlapped with Jiri's change to guard
   the rhashtable_remove_fast() call with a check against
   tc_skip_sw().

5) In mlx4, a revert bug fix in 'net' overlapped with some
   unrelated changes in 'net-next'.

6) In geneve, a stale header pointer after pskb_expand_head()
   bug fix in 'net' overlapped with a large reorganization of
   the same code in 'net-next'.  Since the 'net-next' code no
   longer had the bug in question, there was nothing to do
   other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull ARM SoC fixes from Arnd Bergmann:
 "This should be the last set of bugfixes for arm-soc in v4.9. None of
  these are critical regressions, but it would be nice to still get them
  merged.

   - On the Juno platform, the idle latency was described wrong, leading
     to suboptimal cpuidle tuning.

   - Also on the same platform, PCI I/O space was set up incorrectly and
     could not work.

   - On the sti platform, a syntactically incorrect DT entry caused
     warnings.

   - The newly added 'gr8' platform has somewhat confusing file names,
     which we rename for consistency"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm64: dts: juno: fix cluster sleep state entry latency on all SoC versions
  arm64: dts: juno: Correct PCI IO window
  ARM: dts: STiH407-family: fix i2c nodes
  ARM: gr8: Rename the DTSI and relevant DTS

Pull networking fixes from David Miller:

 1) Lots more phydev and probe error path leaks in various drivers by
    Johan Hovold.

 2) Fix race in packet_set_ring(), from Philip Pettersson.

 3) Use after free in dccp_invalid_packet(), from Eric Dumazet.

 4) Signnedness overflow in SO_{SND,RCV}BUFFORCE, also from Eric
    Dumazet.

 5) When tunneling between ipv4 and ipv6 we can be left with the wrong
    skb->protocol value as we enter the IPSEC engine and this causes all
    kinds of problems. Set it before the output path does any
    dst_output() calls, from Eli Cooper.

 6) bcmgenet uses wrong device struct pointer in DMA API calls, fix from
    Florian Fainelli.

 7) Various netfilter nat bug fixes from FLorian Westphal.

 8) Fix memory leak in ipvlan_link_new(), from Gao Feng.

 9) Locking fixes, particularly wrt. socket lookups, in l2tp from
    Guillaume Nault.

10) Avoid invoking rhash teardowns in atomic context by moving netlink
    cb->done() dump completion from a worker thread. Fix from Herbert
    Xu.

11) Buffer refcount problems in tun and macvtap on errors, from Jason
    Wang.

12) We don't set Kconfig symbol DEFAULT_TCP_CONG properly when the user
    selects BBR. Fix from Julian Wollrath.

13) Fix deadlock in transmit path on altera TSE driver, from Lino
    Sanfilippo.

14) Fix unbalanced reference counting in dsa_switch_tree, from Nikita
    Yushchenko.

15) tc_tunnel_key needs to be properly exported to userspace via uapi,
    fix from Roi Dayan.

16) rds_tcp_init_net() doesn't unregister notifier in error path, fix
    from Sowmini Varadhan.

17) Stale packet header pointer access after pskb_expand_head() in
    genenve driver, fix from Sabrina Dubroca.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (103 commits)
  net: avoid signed overflows for SO_{SND|RCV}BUFFORCE
  geneve: avoid use-after-free of skb->data
  tipc: check minimum bearer MTU
  net: renesas: ravb: unintialized return value
  sh_eth: remove unchecked interrupts for RZ/A1
  net: bcmgenet: Utilize correct struct device for all DMA operations
  NET: usb: qmi_wwan: add support for Telit LE922A PID 0x1040
  cdc_ether: Fix handling connection notification
  ip6_offload: check segs for NULL in ipv6_gso_segment.
  RDS: TCP: unregister_netdevice_notifier() in error path of rds_tcp_init_net
  Revert: "ip6_tunnel: Update skb->protocol to ETH_P_IPV6 in ip6_tnl_xmit()"
  ipv6: Set skb->protocol properly for local output
  ipv4: Set skb->protocol properly for local output
  packet: fix race condition in packet_set_ring
  net: ethernet: altera: TSE: do not use tx queue lock in tx completion handler
  net: ethernet: altera: TSE: Remove unneeded dma sync for tx buffers
  net: ethernet: stmmac: fix of-node and fixed-link-phydev leaks
  net: ethernet: stmmac: platform: fix outdated function header
  net: ethernet: stmmac: dwmac-meson8b: fix probe error path
  net: ethernet: stmmac: dwmac-generic: fix probe error path
  ...

CAP_NET_ADMIN users should not be allowed to set negative
sk_sndbuf or sk_rcvbuf values, as it can lead to various memory
corruptions, crashes, OOM...

Note that before commit 82981930 ("net: cleanups in
sock_setsockopt()"), the bug was even more serious, since SO_SNDBUF
and SO_RCVBUF were vulnerable.

This needs to be backported to all known linux kernels.

Again, many thanks to syzkaller team for discovering this gem.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

geneve{,6}_build_skb can end up doing a pskb_expand_head(), which
makes the ip_hdr(skb) reference we stashed earlier stale. Since it's
only needed as an argument to ip_tunnel_ecn_encap(), move this
directly in the function call.

Fixes: 08399efc ("geneve: ensure ECN info is handled properly in all tx/rx paths")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Qian Zhang (张谦) reported a potential socket buffer overflow in
tipc_msg_build() which is also known as CVE-2016-8632: due to
insufficient checks, a buffer overflow can occur if MTU is too short for
even tipc headers. As anyone can set device MTU in a user/net namespace,
this issue can be abused by a regular user.

As agreed in the discussion on Ben Hutchings' original patch, we should
check the MTU at the moment a bearer is attached rather than for each
processed packet. We also need to repeat the check when bearer MTU is
adjusted to new device MTU. UDP case also needs a check to avoid
overflow when calculating bearer MTU.

Fixes: b97bf3fd ("[TIPC] Initial merge")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reported-by: Qian Zhang (张谦) <zhangqian-c@360.cn>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-4.9-20161201' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2016-12-02

this is a pull request for net/master.

There are two patches by Stephane Grosjean, who adds support for the new
PCAN-USB X6 USB interface to the pcan_usb driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We want to set the other "err" variable here so that we can return it
later.  My version of GCC misses this issue but I caught it with a
static checker.

Fixes: 9f70eb33 ("net: ethernet: renesas: ravb: fix fixed-link phydev leaks")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2016-12-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 4.10

Major changes:

rsi

* filter rx frames
* configure tx power
* make it possible to select antenna
* support 802.11d

brcmfmac

* cleanup of scheduled scan code
* support for bcm43341 chipset with different chip id
* support rev6 of PCIe device interface

ath10k

* add spectral scan support for QCA6174 and QCA9377 families
* show used tx bitrate with 10.4 firmware

wil6210

* add power save mode support
* add abort scan functionality
* add support settings retry limit for short frames

bcma

* add Dell Inspiron 3148
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When streaming a lot of data and the RZ/A1 can't keep up, some status bits
will get set that are not being checked or cleared which cause the
following messages and the Ethernet driver to stop working. This
patch fixes that issue.

irq 21: nobody cared (try booting with the "irqpoll" option)
handlers:
[<c036b71c>] sh_eth_interrupt
Disabling IRQ #21

Fixes: db893473 ("sh_eth: Add support for r7s72100")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

__bcmgenet_tx_reclaim() and bcmgenet_free_rx_buffers() are not using the
same struct device during unmap that was used for the map operation,
which makes DMA-API debugging warn about it. Fix this by always using
&priv->pdev->dev throughout the driver, using an identical device
reference for all map/unmap calls.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Gregory CLEMENT says:

====================
Support Armada 37xx SoC (ARMv8 64-bits) in mvneta driver

The Armada 37xx is a new ARMv8 SoC from Marvell using same network
controller as the older Armada 370/38x/XP SoCs. This series adapts the
driver in order to be able to use it on this new SoC. The main changes
are:

- 64-bits support: the first patches allow using the driver on a 64-bit
  architecture.

- MBUS support: the mbus configuration is different on Armada 37xx
  from the older SoCs.

- per cpu interrupt: Armada 37xx do not support per cpu interrupt for
  the NETA IP, the non-per-CPU behavior was added back.

The first patch is an optimization in the rx path in swbm mode.
The second patch remove unnecessary allocation for HWBM.
The first item is solved by patches 4 and 5.
The 2 last items are solved by patch 6.
In patch 7 the dt support is added.

Beside Armada 37xx, this series have been again tested on Armada XP
and Armada 38x (with Hardware Buffer Management and with Software
Buffer Management).

This is the 6th version of the series:
- 1st version:
http://lists.infradead.org/pipermail/linux-arm-kernel/2016-November/469588.html

- 2nd version:
http://lists.infradead.org/pipermail/linux-arm-kernel/2016-November/470476.html

- 3rd version:
http://lists.infradead.org/pipermail/linux-arm-kernel/2016-November/470901.html

- 4th version:
http://lists.infradead.org/pipermail/linux-arm-kernel/2016-November/471039.html

- 5th version:
http://lists.infradead.org/pipermail/linux-arm-kernel/2016-November/471478.html

Changelog:
v5 -> v6:
 - Added Tested-by from  Marcin Wojtas on the series
 - Added Reviewed-by from Jisheng Zhang on patch 3
 - Fix eth1 phy mode for Armada 3720 DB board on patch 7

v4 -> v5:
 - remove unnecessary cast in patch 3

v3 -> v4:
 - Adding new patch: "net: mvneta: do not allocate buffer in rxq init
   with HWBM"

 - Simplify the HWBM case in patch 3 as suggested by Marcin

v2 -> v3:
 - Adding patch 1 "Optimize rx path for small frame"

 - Fix the kbuild error by moving the "phys_addr += pp->rx_offset_correction;"
  line from patch 2 to patch 3 where rx_offset_correction is introduced.

 - Move the memory allocation of the buf_virt_addr of the rxq to be
   called by the probe function in order to avoid a memory leak.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add neta nodes for network support both in device tree for the SoC and
the board.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Armada 3700 is a new ARMv8 SoC from Marvell using same network controller
as older Armada 370/38x/XP. There are however some differences that
needed taking into account when adding support for it:

* open default MBUS window to 4GB of DRAM - Armada 3700 SoC's Mbus
  configuration for network controller has to be done on two levels:
  global and per-port. The first one is inherited from the
  bootloader. The latter can be opened in a default way, leaving
  arbitration to the bus controller.  Hence filled mbus_dram_target_info
  structure is not needed

* make per-CPU operation optional - Recent patches adding RSS and XPS
  support for Armada 38x/XP enabled per-CPU operation of the controller
  by default. Contrary to older SoC's Armada 3700 SoC's network
  controller is not capable of per-CPU processing due to interrupt lines'
  connectivity.  This patch restores non-per-CPU operation, which is now
  optional and depends on neta_armada3700 flag value in mvneta_port
  structure. In order not to complicate the code, separate interrupt
  subroutine is implemented.

For now, on the Armada 3700, RSS is disabled as the current
implementation depend on the per cpu interrupts.

[gregory.clement@free-electrons.com: extract from a larger patch, replace
some ifdef and port to net-next for v4.10]
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Actually only the mvneta_bm support is not 64-bits compatible.
The mvneta code itself can run on 64-bits architecture.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prepare the mvneta driver in order to be usable on the 64 bits platform
such as the Armada 3700.

[gregory.clement@free-electrons.com]: this patch was extract from a larger
one to ease review and maintenance.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Until now the virtual address of the received buffer were stored in the
cookie field of the rx descriptor. However, this field is 32-bits only
which prevents to use the driver on a 64-bits architecture.

With this patch the virtual address is stored in an array not shared with
the hardware (no more need to use the DMA API). Thanks to this, it is
possible to use cache contrary to the access of the rx descriptor member.

The change is done in the swbm path only because the hwbm uses the cookie
field, this also means that currently the hwbm is not usable in 64-bits.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Jisheng Zhang <jszhang@marvell.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For HWBM all buffers are allocated in mvneta_bm_construct() and in runtime
they are put into descriptors by hardware. There is no need to fill them
at this point.
Suggested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For small frame reuse the phys_addr variable instead of accessing the
uncacheable value in the rx descriptor.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ozgur Karatas reported that the very first entry in the CREDITS file had
the wrong tag for name (M: instead of N: - it happened when moving the
entry from the MAINTAINERS file, where 'M:' stands for "Maintainer").

And when I went looking, I found a couple of other cases of wrong
tagging too.
Reported-by: Ozgur Karatas <mueddib@yandex.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

David Ahern says:

====================
net: Add bpf support for sockets

The recently added VRF support in Linux leverages the bind-to-device
API for programs to specify an L3 domain for a socket. While
SO_BINDTODEVICE has been around for ages, not every ipv4/ipv6 capable
program has support for it. Even for those programs that do support it,
the API requires processes to be started as root (CAP_NET_RAW) which
is not desirable from a general security perspective.

This patch set leverages Daniel Mack's work to attach bpf programs to
a cgroup to provide a capability to set sk_bound_dev_if for all
AF_INET{6} sockets opened by a process in a cgroup when the sockets
are allocated.

For example:
 1. configure vrf (e.g., using ifupdown2)
        auto eth0
        iface eth0 inet dhcp
            vrf mgmt

        auto mgmt
        iface mgmt
            vrf-table auto

 2. configure cgroup
        mount -t cgroup2 none /tmp/cgroupv2
        mkdir /tmp/cgroupv2/mgmt
        test_cgrp2_sock /tmp/cgroupv2/mgmt 15

 3. set shell into cgroup (e.g., can be done at login using pam)
        echo $$ >> /tmp/cgroupv2/mgmt/cgroup.procs

At this point all commands run in the shell (e.g, apt) have sockets
automatically bound to the VRF (see output of ss -ap 'dev == <vrf>'),
including processes not running as root.

This capability enables running any program in a VRF context and is key
to deploying Management VRF, a fundamental configuration for networking
gear, with any Linux OS installation.

This patchset also exports the socket family, type and protocol as
read-only allowing bpf filters to deny a process in a cgroup the ability
to open specific types of AF_INET or AF_INET6 sockets.

v7
- comments from Alexei

v6
- add export of socket family, type and protocol
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add examples preventing a process in a cgroup from opening a socket
based family, protocol and type.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for section names starting with cgroup/skb and cgroup/sock.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add socket family, type and protocol to bpf_sock allowing bpf programs
read-only access.

Add __sk_flags_offset[0] to struct sock before the bitfield to
programmtically determine the offset of the unsigned int containing
protocol and type.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a simple program to demonstrate the ability to attach a bpf program
to a cgroup that sets sk_bound_dev_if for AF_INET{6} sockets when they
are created.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add new cgroup based program type, BPF_PROG_TYPE_CGROUP_SOCK. Similar to
BPF_PROG_TYPE_CGROUP_SKB programs can be attached to a cgroup and run
any time a process in the cgroup opens an AF_INET or AF_INET6 socket.
Currently only sk_bound_dev_if is exported to userspace for modification
by a bpf program.

This allows a cgroup to be configured such that AF_INET{6} sockets opened
by processes are automatically bound to a specific device. In turn, this
enables the running of programs that do not support SO_BINDTODEVICE in a
specific VRF context / L3 domain.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Code move and rename only; no functional change intended.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for PID 0x1040 of Telit LE922A.

The qmi adapter requires to have DTR set for proper working,
so QMI_WWAN_QUIRK_DTR has been enabled.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>