- 02 Jun, 2014 29 commits
-
-
Mario Kleiner authored
The Sony PVM-2541A OLED high precision color display supports both 10 bpc and 12 bpc hdmi deep color input, but its edid does not signal any deep color support. Add a quirk to force it being treated as a 12 bpc panel. Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-
Mario Kleiner authored
Check the HDMI cea block for deep color mode bits. If available, assign the highest supported bpc for a hdmi display, corresponding to the given deep color modes. Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-
Mario Kleiner authored
DCE-4/5/6 can't support more than 12 bpc deep color over hdmi, so clamp to 12 bpc when a hdmi deep color capable display is connected. This even makes sense on DCE-8+, which could do up to 16 bpc, as driving with more than 12 bpc would only waste video bandwidth as long as we don't support framebuffers with more than 12 bpc depth. On pre-DCE4 we clamp hdmi bit depth to 8 bpc, as those asics don't support hdmi deep color. Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-
Alex Deucher authored
Program HDMI_CONTROL to send general control packets for hdmi deep color mode signalling at every video frame if bpc > 8. This is only supported on evergreen / DCE-4 and later. v2: rebase Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-
Alex Deucher authored
Need to adjust the pll up for deep color modes. Additionally, the atom bpc defines were wrong in certain cases. v2: set the adjusted clock to the pll clock for hdmi deep color. This fixes display and audio issues with deep color as reported by Andy Furniss <adf.lists@gmail.com> v3: set crtc_clock as well v4: setcrtcinfo on the adjusted mode v5: just use the adjusted clock for setting the pll v6: only use the adjusted clock for hdmi v7: only DCE5 and DCE6 and bpc > 8 Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-
Alex Deucher authored
I'm not really sure how these should be calculated for deep color. The hw generated values seem to work. Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-
Alex Deucher authored
May fix display issues with non-HDMI displays. Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
-
Alex Deucher authored
We need to specify the encoder mode as LVDS for eDP when using the Crtc_Source atom table in order to properly set up the FMT hardware. bug: https://bugs.freedesktop.org/show_bug.cgi?id=73911Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
-
Christian König authored
Fill VM page tables from the GART page table if applicable. v2: fix copy&paste error Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-
Christian König authored
Fill VM page tables from the GART page table if applicable. Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-
Christian König authored
Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-
Christian König authored
Instead of trying to flip inside the vblank period when the buffer is idle, offload blocking for idle to a kernel thread and program the flip directly into the hardware. v2: add error handling, fix EBUSY handling v3: add proper exclusive_lock handling Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-
Christian König authored
Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-
Christian König authored
Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-
Christian König authored
We activate the VBLANK irq manually anyway, so this is unnecessary. Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-
Christian König authored
They are doing the same on all generations anyway. Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-
Alex Deucher authored
Only DCE5+ asics support DP 1.2. Noticed by ArtForz on IRC. Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
-
Alex Deucher authored
We were checking the ext clock rather than the display clock. Noticed by ArtForz on IRC. Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
-
Émeric MASCHINO authored
Removes useless quirk a7f465f73363fce409870f62173d518b1bc02ae6 introduced with fdo #7770 as a failed attempt to minimize stability issues with hp zx1 chipset/ ATI FireGL X1 graphics adapter configuration (see http://marc.info/?l=linux-ia64&m=140077543819871&w=2 for details/reason) Signed-off-by: Émeric MASCHINO <emeric.maschino@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-
Alex Deucher authored
Avoids blank screens on muxed systems when runpm is active. bug: https://bugs.freedesktop.org/show_bug.cgi?id=75917Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
-
Michele CURTI authored
Signed-off-by: Michele Curti <michele.curti@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-
Michele CURTI authored
Signed-off-by: Michele Curti <michele.curti@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-
Rafał Miłecki authored
Thanks to advanced RE of fglrx we finally know what exactly needs to be handled of AFMT change. This has been tested for possible regressions on: 1) DCE2 HD2400 (RV610) 2) DCE3 HD3470 (RV620) For a reference and details see: https://bugzilla.kernel.org/show_bug.cgi?id=76231Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-
Rafał Miłecki authored
Recent RE efforts revealed ops performed by fglrx during HDMI setup. This mostly adds masks to r/w ops plus few single missing bits. This has been tested for possible regressions on: 1) DCE2 HD2400 (RV610) 2) DCE3 HD3470 (RV620) For a reference and details see: https://bugzilla.kernel.org/show_bug.cgi?id=76231Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-
Rafał Miłecki authored
What initially seemed to be a typo in fglrx (using register 0x740c instead of 0x74dc) appeared to be a correct behavior. DCE3 has ACR and CRC registers swapped which explains why we needed WREG32(HDMI0_AUDIO_CRC_CONTROL + offset, 0x1000); This has been tested for possible regressions on DCE3 HD3470 (RV620). Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-
Rafał Miłecki authored
DCE 3.1 and 3.2 should be programmed in a different way than DCE 2 and DCE 3. The order of setting registers and sets of registers are different. It's still unsure how we will handle DCE 3.1 vs. DCE 3.2, since they have few differences as well. For now separate DCE 2 and DCE 3 path, so we can work on it without a risk of breaking DCE 3.1+. This has been tested for possible regressions on DCE32 HD4550 (RV710). Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-
Christian König authored
This patch makes it possible to decide how many address bits are spend on the page directory vs the page tables. v2: remove unintended change Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-
Christian König authored
This patch implements support for VRAM page table entry compression. PTE construction is enhanced to identify physically contiguous page ranges and mark them in the PTE fragment field. L1/L2 TLB support is enabled for 64KB (SI/CIK) and 256KB (NI) PTE fragments, significantly improving TLB utilization for VRAM allocations. Linear store bandwidth is improved from 60GB/s to 125GB/s on Pitcairn. Unigine Heaven 3.0 sees an average improvement from 24.7 to 27.7 FPS on default settings at 1920x1200 resolution with vsync disabled. See main comment in radeon_vm.c for a technical description. v2 (chk): rebased and simplified. v3 (chk): add missing hw setup v4 (chk): rebased on current drm-fixes-3.15 v5 (chk): fix comments and commit text Signed-off-by: Jay Cornwall <jay@jcornwall.me> Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-
Alex Deucher authored
The i2c and aux buses use the same pads so add a mutex to protect access to the pads. Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Christian König <christian.koenig@amd.com>
-
- 30 May, 2014 3 commits
-
-
Dave Airlie authored
This adds an encoder type for DP MST encoders. Reviewed-by: Todd Previte <tprevite@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
-
Jani Nikula authored
This makes drm_get_encoder_name() thread safe. Reference: http://lkml.kernel.org/r/645ee6e22cad47d38a2b35c21c8d5fe3@DC1-MBX-01\ .ptsecurity.ru Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
-
Jani Nikula authored
This makes drm_get_connector_name() thread safe. [airlied: fix to build.] Reference: http://lkml.kernel.org/r/645ee6e22cad47d38a2b35c21c8d5fe3@DC1-MBX-01.ptsecurity.ruSigned-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
-
- 27 May, 2014 8 commits
-
-
Thierry Reding authored
Commit 9dc40560 (drm/dp: let drivers specify the name of the I2C- over-AUX adapter) introduced a new field but didn't add the proper kernel-doc for it. Signed-off-by: Thierry Reding <treding@nvidia.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
-
David Herrmann authored
shmem_read_mapping_page() uses mapping_gfp_mask(mapping) as default gfp mask. No reason to use shmem_read_mapping_page_gfp() directly if we want the default behavior. Acked-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
-
David Herrmann authored
shmem supports page-relocations during swapin since quite some time. It was implemented in: commit bde05d1c Author: Hugh Dickins <hughd@google.com> Date: Tue May 29 15:06:38 2012 -0700 shmem: replace page if mapping excludes its zone The gem-comment about wrongly placed DMA32 pages is no longer valid. Replace it with a proper comment but keep the BUG_ON() to verify correct shmem behavior. Signed-off-by: David Herrmann <dh.herrmann@gmail.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
-
Benoit Taine authored
This issue was reported by coccicheck using the semantic patch at scripts/coccinelle/api/memdup.cocci Signed-off-by: Benoit Taine <benoit.taine@lip6.fr> Signed-off-by: Dave Airlie <airlied@redhat.com>
-
Jean Delvare authored
The shmobile DRM driver is only useful on SuperH and shmobile unless build testing. I am dropping the SuperH dependencies though because the driver doesn't even build there, so in practice it is an arm-only driver for now. Signed-off-by: Jean Delvare <jdelvare@suse.de> Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
-
Jean Delvare authored
The Renesas R-Car Display Unit driver is only useful on shmobile unless build testing. The LVDS output is useful on an even more reduced hardware set. Signed-off-by: Jean Delvare <jdelvare@suse.de> Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
-
Daniel Vetter authored
DRM is pretty much the main user of this stuff (if we ignore the sysfs interface used by X, i.e. by the same gang of people writing the drm drivers). So shovel it into Dave's responsibility to avoid patches getting lost on lkml. With this get_maintainers will rout vgaarb and switcheroo patches correctly. Cc: Alex Williamson <alex.williamson@redhat.com> Cc: Dave Airlie <airlied@redhat.com> Cc: linux-kernel@vger.kernel.org References: https://lkml.org/lkml/2014/5/25/94Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
-
Sagar Kamble authored
Started documenting drm properties for drm drivers. This patch provides information about properties in drm, i915, psb and cdv/gma-500. Information about other properties can be added on top of these. v2: Added description of drm properties in armada, exynos, i2c/ch7006, noveau, omap, qxl, radeon, rcar-du v3: Removed "Property Object" column since it is implementation related. Property type column refined.[Ville's review comments] v4: Removed whitespace warnings and minor nits. [Randy's review comments] v5: Restructured output for ENUM properties v6: Review comments on formatting the table. [Laurent's review comments] v7: Minor restructuring. [Laurent's review comments] Cc: Rob Landley <rob@landley.net> Cc: Dave Airlie <airlied@redhat.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Cc: David Herrmann <dh.herrmann@gmail.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com> Cc: Sagar Kamble <sagar.a.kamble@intel.com> Cc: "Purushothaman, Vijay A" <vijay.a.purushothaman@intel.com> Cc: linux-doc@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Signed-off-by: Sagar Kamble <sagar.a.kamble@intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
-