- 28 Jan, 2008 40 commits
-
-
Patrick McHardy authored
Kill the defines again, convert to the new checksum helper names and remove the dependency of NET_ACT_NAT on NETFILTER. Signed-off-by:
Patrick McHardy <kaber@trash.net> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Patrick McHardy authored
This allows to get rid of the CONFIG_NETFILTER dependency of NET_ACT_NAT. This patch redefines the old names to keep the noise low, the next patch converts all users. Signed-off-by:
-
Gerrit Renker authored
This removes a redundant test for unexpected packet types. In dccp_rcv_state_process it is tested twice whether a DCCP-server has received a CloseReq (Step 7): * first in the combined if-statement, * then in the call to dccp_rcv_closereq(). The latter is necesssary since dccp_rcv_closereq() is also called from __dccp_rcv_established(). This patch removes the duplicate test. Signed-off-by:
Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Gerrit Renker authored
This adds the necessary state transitions for the two forms of passive-close * PASSIVE_CLOSE - which is entered when a host receives a Close; * PASSIVE_CLOSEREQ - which is entered when a client receives a CloseReq. Here is a detailed account of what the patch does in each state. 1) Receiving CloseReq The pseudo-code in 8.5 says: Step 13: Process CloseReq If P.type == CloseReq and S.state < CLOSEREQ, Generate Close S.state := CLOSING Set CLOSING timer. This means we need to address what to do in CLOSED, LISTEN, REQUEST, RESPOND, PARTOPEN, and OPEN. * CLOSED: silently ignore - it may be a late or duplicate CloseReq; * LISTEN/RESPOND: will not appear, since Step 7 is performed first (we know we are the client); * REQUEST: perform Step 13 directly (no need to enqueue packet); * OPEN/PARTOPEN: enter PASSIVE_CLOSEREQ so that the application has a chance to process unread data. When already in PASSIVE_CLOSEREQ, no second CloseReq is enqueued. In any other state, the CloseReq is ignored. I think that this offers some robustness against rare and pathological cases: e.g. a simultaneous close where the client sends a Close and the server a CloseReq. The client will then be retransmitting its Close until it gets the Reset, so ignoring the CloseReq while in state CLOSING is sane. 2) Receiving Close The code below from 8.5 is unconditional. Step 14: Process Close If P.type == Close, Generate Reset(Closed) Tear down connection Drop packet and return Thus we need to consider all states: * CLOSED: silently ignore, since this can happen when a retransmitted or late Close arrives; * LISTEN: dccp_rcv_state_process() will generate a Reset ("No Connection"); * REQUEST: perform Step 14 directly (no need to enqueue packet); * RESPOND: dccp_check_req() will generate a Reset ("Packet Error") -- left it at that; * OPEN/PARTOPEN: enter PASSIVE_CLOSE so that application has a chance to process unread data; * CLOSEREQ: server performed active-close -- perform Step 14; * CLOSING: simultaneous-close: use a tie-breaker to avoid message ping-pong (see comment); * PASSIVE_CLOSEREQ: ignore - the peer has a bug (sending first a CloseReq and now a Close); * TIMEWAIT: packet is ignored. Note that the condition of receiving a packet in state CLOSED here is different from the condition "there is no socket for such a connection": the socket still exists, but its state indicates it is unusable. Last, dccp_finish_passive_close sets either DCCP_CLOSED or DCCP_CLOSING = TCP_CLOSING, so that sk_stream_wait_close() will wait for the final Reset (which will trigger CLOSING => CLOSED). Signed-off-by: -
Gerrit Renker authored
This adds two auxiliary states to deal with passive closes: * PASSIVE_CLOSE (reached from OPEN via reception of Close) and * PASSIVE_CLOSEREQ (reached from OPEN via reception of CloseReq) as internal intermediate states. These states are used to allow a receiver to process unread data before acknowledging the received connection-termination-request (the Close/CloseReq). Without such support, it will happen that passively-closed sockets enter CLOSED state while there is still unprocessed data in the queue; leading to unexpected and erratic API behaviour. PASSIVE_CLOSE has been mapped into TCPF_CLOSE_WAIT, so that the code will seamlessly work with inet_accept() (which tests for this state). The state names are thanks to Arnaldo, who suggested this naming scheme following an earlier revision of this patch. Signed-off-by:
-
Gerrit Renker authored
This fixes a nasty bug: dccp_send_reset() is called by both DCCPv4 and DCCPv6, but uses inet_sk_rebuild_header() in each case. This leads to unpredictable and weird behaviour: under some conditions, DCCPv6 Resets were sent, in other not. The fix is to use the AF-independent rebuild_header routine. Signed-off-by:
-
Arnaldo Carvalho de Melo authored
This patch was based on another made by Gerrit Renker, his changelog was: ------------------------------------------------------ The patch set migrates TFRC TX history to a singly-linked list. The details are: * use of a consistent naming scheme (all TFRC functions now begin with `tfrc_'); * allocation and cleanup are taken care of internally; * provision of a lookup function, which is used by the CCID TX infrastructure to determine the time a packet was sent (in turn used for RTT sampling); * integration of the new interface with the present use in CCID3. ------------------------------------------------------ Simplifications I did: . removing the tfrc_tx_hist_head that had a pointer to the list head and another for the slabcache. . No need for creating a slabcache for each CCID that wants to use the TFRC tx history routines, create a single slabcache when the dccp_tfrc_lib module init routine is called. Signed-off-by: -
Ilpo Järvinen authored
1) Skip condition used to be wrong way around which made SACK processing very broken, missed many blocks because of that. 2) Use highest_sack advancement only if some skbs are already sacked because otherwise tcp_write_queue_next may move things too far (occurs mainly with GSO). The other similar advancement is not problem because highest_sack was previosly put to point a sacked skb. These problems were located because of problem report from Matt Mathis <mathis@psc.edu>. Signed-off-by:
Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by:
-
Pavel Emelyanov authored
The if (statement) WARN_ON(1); looks much better as WARN_ON(statement); Signed-off-by:Pavel Emelyanov <xemul@openvz.org> Signed-off-by:
-
Fred L. Templin authored
This patch includes support for the Intra-Site Automatic Tunnel Addressing Protocol (ISATAP) per RFC4214. It uses the SIT module, and is configured using extensions to the "iproute2" utility. The diffs are specific to the Linux 2.6.24-rc2 kernel distribution. This version includes the diff for ./include/linux/if.h which was missing in the v2.4 submission and is needed to make the patch compile. The patch has been installed, compiled and tested in a clean 2.6.24-rc2 kernel build area. Signed-off-by:
Fred L. Templin <fred.l.templin@boeing.com> Signed-off-by:
YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by:
-
Pavel Emelyanov authored
The 3rd argument is always zero (according to grep :) Eliminate it and merge the function with sk_stream_alloc_skb. This saves 44 more bytes, and together with the previous patch we have: add/remove: 1/0 grow/shrink: 0/8 up/down: 183/-751 (-568) function old new delta sk_stream_alloc_skb - 183 +183 ip_rt_init 529 525 -4 arp_ignore 112 107 -5 __inet_lookup_listener 284 274 -10 tcp_sendmsg 2583 2481 -102 tcp_sendpage 1449 1300 -149 tso_fragment 417 258 -159 tcp_fragment 1149 988 -161 __tcp_push_pending_frames 1998 1837 -161 Signed-off-by:
-
Pavel Emelyanov authored
This function seems too big for inlining. Indeed, it saves half-a-kilo when uninlined: add/remove: 1/0 grow/shrink: 0/7 up/down: 195/-719 (-524) function old new delta sk_stream_alloc_pskb - 195 +195 ip_rt_init 529 525 -4 __inet_lookup_listener 284 274 -10 tcp_sendmsg 2583 2486 -97 tcp_sendpage 1449 1305 -144 tso_fragment 417 267 -150 tcp_fragment 1149 992 -157 __tcp_push_pending_frames 1998 1841 -157 Signed-off-by:
-
Joonwoo Park authored
fib_hash: kmalloc + memset conversion to kzalloc fix to avoid memset entirely. Signed-off-by:
Joonwoo Park <joonwpark81@gmail.com> Signed-off-by:
-
Joonwoo Park authored
fib_semantics: kmalloc + memset conversion to kzalloc fix to avoid memset entirely. Signed-off-by:
-
Joonwoo Park authored
2007/11/26, Patrick McHardy <kaber@trash.net>: > How about also switching vmalloc/get_free_pages to GFP_ZERO > and getting rid of the memset entirely while you're at it? > xfrm_hash: kmalloc + memset conversion to kzalloc fix to avoid memset entirely. Signed-off-by:
-
Ilpo Järvinen authored
Better place exists in update_send_head (other non-queue related adjustments are done there as well) which is the only caller of tcp_advance_send_head (now that the bogus call from mtu_probe is gone). Signed-off-by:
-
Pavel Emelyanov authored
Currently this size is 16, but as the comment says this is so only because all the chains (except one) has the length 1. I think, that some day this may change, so growing this hash will be much easier. Besides, symbolic names are read better than magic constants. Signed-off-by:
-
Pavel Emelyanov authored
The sock_wake_async() performs a bit different actions depending on "how" argument. Unfortunately this argument ony has numerical magic values. I propose to give names to their constants to help people reading this function callers understand what's going on without looking into this function all the time. I suppose this is 2.6.25 material, but if it's not (or the naming seems poor/bad/awful), I can rework it against the current net-2.6 tree. Signed-off-by:
-
Gerrit Renker authored
This continues from the previous patch and adds support for actively aborting a DCCP connection, using a Reset Code 2, "Aborted" to inform the peer of an abortive release. I have tried this in various client/server settings and it works as expected. Signed-off-by:
Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by:
-
Gerrit Renker authored
This removes one FIXME with regard to close when there is still unread data. The mechanism is implemented similar to TCP: with regard to DCCP-specifics, a Reset with Code 2, "Aborted" is sent to the peer. This corresponds in part to RFC 4340, 8.1.1 and 8.1.5. Signed-off-by:
-
Gerrit Renker authored
This removes a comment which identifies an `issue' with dccp_write_xmit() where there is none. The comment assumes it is possible that a packet is sent between the calls to ccid_hc_tx_send_packet(), dccp_transmit_skb(), ccid_hc_tx_packet_sent() (in the above order) in dccp_write_xmit(). I think that this is impossible, since dccp_write_xmit() is always called under lock: * when called as dccp_write_xmit(sk, 1) from dccp_send_close(), the socket is locked (see code comment above dccp_send_close()); * when called as dccp_write_xmit(sk, 0) from dccp_send_msg(), it is after lock_sock() has been called; * when called as dccp_write_xmit(sk, 0) from dccp_write_xmit_timer(), bh_lock_sock() has been called and the if/else statement has made sure that sk_lock.owner is not set; * there are no other places where dccp_write_xmit() is called. Furthermore, the debug statement for printing the sequence number of the packet just sent has been removed, since the entire list is being printed anyway and so the entry of that number appears last. Signed-off-by:
-
Gerrit Renker authored
The code used two different variables to count Acks, one of them redundant. This patch reduces the number of Ack counters to one. The type of the Ack counter has also been changed to u32 (twice the range of int); and the variable has been renamed into `packets_acked' - for consistency with RFC 3465 (and similarly named variables are used by TCP and SCTP). Lastly, a slightly less aggressive `maxincr' increment is used (for even Ack Ratios, maxincr was Ack Ratio/2 + 1 instead of Ack Ratio/2). Signed-off-by:
-
Gerrit Renker authored
This removes the synchronisation variable `ccid2hctx_sendwait', which is set to 1 when the CCID2 sender may send a new packet, and which is set to 0 otherwise The variable is redundant, since it is only used in combination with the hc_tx_send_packet/ hc_tx_packet_sent function pair. Both functions are called under socket lock, so the following happens when the CCID2 may send a new packet: * it sets sendwait = 1 in tx_send_packet and returns 0; * the subsequent call to tx_packet_sent clears the sendwait flag; * since tx_send_packet returns 0 if and only if sendwait == 1, the BUG_ON condition in tx_packet_sent is never satisfied, since that function is never called when tx_send_packet returns a value different from 0 (cf. dccp_write_xmit); * the call to tx_packet_sent clears the flag so that the condition "!sendwait" is true the next time tx_packet_sent is called. In other words, it is sufficient to just return 0 / not-0 to synchronise tx_send_packet and tx_packet_sent -- which is what the patch does. Signed-off-by:
-
Gerrit Renker authored
This reduces the amount of redundant debugging messages: * pipe/cwnd are printed in both tx_send_packet() and tx_packet_sent(). Both functions are called immediately after one another, so one occurrence is sufficient. * Since tx_packet_sent() prints pipe/cwnd already, the second printk for pipe is redundant. * In tx_packet_sent() the check_sanity function is called twice (at the begin and at the end). Signed-off-by:
-
Gerrit Renker authored
The function ccid2_change_pipe only does an assignment. This patch simplifies the code by replacing the function with the assignment it performs. Furthermore, the type of pipe is promoted from `signed' to unsigned (increasing the range). As a result, a BUG_ON test for negative values now becomes obsolete (for safety not removed, but replaced with a less annoying `DCCP_BUG'). Signed-off-by:
-
Gerrit Renker authored
The current function ccid2_change_cwnd in effect makes only an assignment, as the test whether cwnd has reached 0 is only required when cwnd is halved. This patch simplifies the code by replacing the function with the assignment it performs. Furthermore, since ssthresh derives from cwnd and appears in many assignments and comparisons, the type of ssthresh has also been changed to match that of cwnd. Signed-off-by:
-
Gerrit Renker authored
This replaces the field member `numdupack', which was used as a read-only constant in the code, with a #define. Signed-off-by:
-
Gerrit Renker authored
This removes a variable `ccid2hctx_sent' which is incremented but never referenced/read (i.e., dead code). Signed-off-by:
-
Gerrit Renker authored
This comments out a problematic section comprising a half-finished algorithm: - The variable `ccid2hctx_ackloss' is never initialised to a value different from 0 and hence in fact is a read-only constant. - The `arsent' variable counts packets other than Acks (it is incremented for every packet), and there is no test for Ack Loss. - The concept of counting Acks as such leads to a complex calculation, and the calculation at the moment is inconsistent with this concept. The problem is that the number of Acks - rather than the number of windows - is counted, which leads to a complex (cubic/quadratic) expression - this is not even implemented. In its current state, the commented-out algorithm interfers with normal processing by changing Ack Ratio incorrectly, and at the wrong times. A new algorithm is necessary, which will not necessarily use the same variables as used by the unfinished one; hence the old variables have been removed. Signed-off-by:
-
Gerrit Renker authored
RFC 4341, sec. 5 states that "The cwnd parameter is initialized to at most four packets for new connections, following the rules from [RFC3390]", which is implemented by this patch. Signed-off-by:
-
Arnaldo Carvalho de Melo authored
This is because in the next patch CCID2 will assume that dccps_mss_cache is non-zero. Signed-off-by:
-
Gerrit Renker authored
This patch removes a bug in the current code. I agree with Andrea's comment that there is a problem here but the way it is treated does not fix it. The problem is that whenever Ack Ratio > cwnd, starvation/deadlock occurs: * the receiver will not send an Ack until (Ack Ratio - cwnd) data packets have arrived; * the sender will not send any data packet before the receipt of an Ack advances the send window. The only way that the connection then progresses was via RTO timeout. In one extreme case (bulk transfer), it was observed that this happened for every single packet; i.e. hundreds of packets, each a RTO timeout of 1..3 seconds apart: a transfer which normally would take a fraction of a second thus grew to several minutes. The solution taken by this approach is to observe the relation "Ack Ratio <= cwnd" by using the constraint (1) from RFC 4341, 6.1.2; i.e. set Ack Ratio = ceil(cwnd / 2) and update it whenever either Ack Ratio or cwnd change. This ensures that the deadlock problem can not arise. Signed-off-by: -
Gerrit Renker authored
Since it makes not sense to assign negative values to Ack Ratio, this patch disallows this possibility. As a consequence, a Bug test for negative Ack Ratio values becomes obsolete. Furthermore, a check against overflow (as Ack Ratio may not exceed 2 bytes, due to RFC 4340, 11.3) has been added. Signed-off-by:
-
Gerrit Renker authored
This replaces use of normal subtraction with modulo-48 subtraction. Signed-off-by:
-
Gerrit Renker authored
In CCID2 the receiver-history is sorted in ascending order of sequence number, but the processing of received Ack Vectors requires the list traversal in the opposite direction. The current code has a bug in this regard: the list traversal is upwards. As a consequence, only Ack Vectors with a run length of 1 will pass, in all other Ack Vectors the remaining (acked) sequence numbers are missed, and may later falsely be identified as lost. Note: This bug is only visible when Ack Ratio > 1, since otherwise the run lengths of Ack Vectors are 0. Signed-off-by: -
Gerrit Renker authored
This is reduces the length of the struct ackvec/ackvec_record fields. It is a purely text-based replacement: s#dccpavr_#avr_#g; s#dccpav_#av_#g; and increases readability somewhat. Signed-off-by:
-
Ilpo Järvinen authored
I keep getting this build error and couldn't find anyone fixing it in archives. ...Maybe all net developers except me build just SMP kernels :-). In file included from include/net/sock.h:50, from ipc/mqueue.c:35: include/linux/pcounter.h: In function 'pcounter_add': include/linux/pcounter.h:87: error: 'struct pcounter' has no member named 'value' make[1]: *** [ipc/mqueue.o] Error 1 make: *** [ipc] Error 2 Signed-off-by: -
Pavel Emelyanov authored
It seems that net/ipv6/af_inet6.c was copied from net/ipv4/af_inet.c, but one comment was not fixed. Signed-off-by:
-
Pavel Emelyanov authored
The first_unix_socket() and next_unix_sockets() are now used in proc file and in forall_unix_socets macro only. The forall_unix_sockets is not used in this file at all so remove it. After this move the helpers to where they really belong, i.e. closer to proc code under the #ifdef CONFIG_PROC_FS option. Signed-off-by:
-
Gerrit Renker authored
Signed-off-by:
-
