- 03 Aug, 2017 7 commits
-
-
Manikanta Pubbisetty authored
WMI interface for all the firmwares(except QCA6174) does not include the type of peer(default/bss/tdls) requested during peer creation, therefore target creates a default peer. TDLS implementation on 10.4 firmware requires host to configure the peer type(tdls) for TDLS peers. This patch adds peer type parameter to the existing WMI interface for peer creation to accommodate this requirement. Tested this change on QCA9888(10.4-3.5.1-00018) and QCA988x(10.2.4.70.9-2) with ping tests for AP/STA modes. Signed-off-by:
Manikanta Pubbisetty <mpubbise@qti.qualcomm.com> Signed-off-by:
Kalle Valo <kvalo@qca.qualcomm.com>
-
Manikanta Pubbisetty authored
This patch adds the support of TDLS feature for 10.4 firmware versions. A new WMI service is added to advertise the support of TDLS for 10.4 firmwares. Signed-off-by:
-
Manikanta Pubbisetty authored
Though there is room to accommodate 512 services in wmi service ready event, target uses only first 4-bits of each 32-bit word for advertising wmi services thereby limiting max wmi services to 64. TDLS implementation for 10.4 firmwares introduces new wmi services by making use of remaining unused bits of each 32-bit word, therefore the wmi service mapping in host needs to be extended. This patch adds the logic to extend the wmi SVCMAP to accommodate new wmi services. Signed-off-by:
-
Erik Stromdahl authored
As suggested by Arnd Bergmann, replace "while (time_before_...) {}" with "do {} while (time_before_...)" This fixes the following warnings detected by gcc 4.1.2: drivers/net/wireless/ath/ath10k/sdio.c: In function ‘ath10k_sdio_mbox_rxmsg_pending_handler’: drivers/net/wireless/ath/ath10k/sdio.c:676: warning: ‘ret’ may be used uninitialized in this function ... drivers/net/wireless/ath/ath10k/sdio.c: In function ‘ath10k_sdio_irq_handler’: drivers/net/wireless/ath/ath10k/sdio.c:1331: warning: ‘ret’ may be used uninitialized in this function Signed-off-by:Erik Stromdahl <erik.stromdahl@gmail.com> Signed-off-by:
-
Erik Stromdahl authored
Chipsets like QCA9377 have support for USB so add initial USB bus support to ath10k. With this patch we have the low level HIF and HTC protocol working and it's possible to boot the firmware, but it's still not possible to connect or anything like. More changes are needed for full functionality. For that reason we print during initialisation: WARNING: ath10k USB support is incomplete, don't expect anything to work! Signed-off-by:
-
Erik Stromdahl authored
Definitions for USB based chipsets Signed-off-by:
-
Matthias Frei authored
Set the a-mpdu reference number in ath10k to make it accessible in the receivers radiotap header. Implemented as in ath9k. The reference number is needed for troubleshooting and research at the receivers site (e.g. to identify mpdu's that were aggregated in an a-mpdu) Signed-off-by:
Matthias Frei <mf@frei.media> [kvalo@qca.qualcomm.com: fix checkpatch warning, commit log cleanup] Signed-off-by:
-
- 28 Jul, 2017 1 commit
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for 4.14. Major changes: ath10k * preparation for wcn3990 support
-
- 27 Jul, 2017 12 commits
-
-
Cong Wang authored
This fixes the following kernel warning: [ 5668.771453] BUG: spinlock bad magic on CPU#0, kworker/u2:3/9745 [ 5668.771850] lock: 0xce63ef20, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0 [ 5668.772277] CPU: 0 PID: 9745 Comm: kworker/u2:3 Tainted: G W 4.12.0-03002-gec979a4-dirty #40 [ 5668.772796] Hardware name: Nokia RX-51 board [ 5668.773071] Workqueue: phy1 wl1251_irq_work [ 5668.773345] [<c010c9e4>] (unwind_backtrace) from [<c010a274>] (show_stack+0x10/0x14) [ 5668.773803] [<c010a274>] (show_stack) from [<c01545a4>] (do_raw_spin_lock+0x6c/0xa0) [ 5668.774230] [<c01545a4>] (do_raw_spin_lock) from [<c06ca578>] (_raw_spin_lock_irqsave+0x10/0x18) [ 5668.774658] [<c06ca578>] (_raw_spin_lock_irqsave) from [<c048c010>] (wl1251_op_tx+0x38/0x5c) [ 5668.775115] [<c048c010>] (wl1251_op_tx) from [<c06a12e8>] (ieee80211_tx_frags+0x188/0x1c0) [ 5668.775543] [<c06a12e8>] (ieee80211_tx_frags) from [<c06a138c>] (__ieee80211_tx+0x6c/0x130) [ 5668.775970] [<c06a138c>] (__ieee80211_tx) from [<c06a3dbc>] (ieee80211_tx+0xdc/0x104) [ 5668.776367] [<c06a3dbc>] (ieee80211_tx) from [<c06a4af0>] (__ieee80211_subif_start_xmit+0x454/0x8c8) [ 5668.776824] [<c06a4af0>] (__ieee80211_subif_start_xmit) from [<c06a4f94>] (ieee80211_subif_start_xmit+0x30/0x2fc) [ 5668.777343] [<c06a4f94>] (ieee80211_subif_start_xmit) from [<c0578848>] (dev_hard_start_xmit+0x80/0x118) ... by adding the missing spin_lock_init(). Reported-by:
Pavel Machek <pavel@ucw.cz> Cc: Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Acked-by:
Kalle Valo <kvalo@codeaurora.org>
-
Florian Fainelli authored
Broadcom BCM53573 SoCs actually have 32 GPIOs, and not 16. Fixes: 3f37ec79 ("bcma: support BCM53573 series of wireless SoCs") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Colin Ian King authored
The current code kfree's entry and then dereferences it by accessing entry->bssid. Avoid the dereference-after-free by moving the kfree after the access to entry->bssid. Detected by CoverityScan, CID#1448600 ("Read from pointer after free") Signed-off-by:Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Brian Norris authored
mwifiex records information about various channels as it receives scan information. It does this by appending to a buffer that was sized to the max number of supported channels on any band, but there are numerous problems: (a) scans can return info from more than one band (e.g., both 2.4 and 5 GHz), so the determined "max" is not large enough (b) some firmware appears to return multiple results for a given channel, so the max *really* isn't large enough (c) there is no bounds checking when stashing these stats, so problems (a) and (b) can easily lead to buffer overflows Let's patch this by setting a slightly-more-correct max (that accounts for a combination of both 2.4G and 5G bands) and adding a bounds check when writing to our statistics buffer. Due to problem (b), we still might not properly report all known survey information (e.g., with "iw <dev> survey dump"), since duplicate results (or otherwise "larger than expected" results) will cause some truncation. But that's a problem for a future bugfix. (And because of this known deficiency, only log the excess at the WARN level, since that isn't visible by default in this driver and would otherwise be a bit too noisy.) Fixes: bf354433 ("mwifiex: channel statistics support for mwifiex") Cc: <stable@vger.kernel.org> Cc: Avinash Patil <patila@marvell.com> Cc: Xinming Hu <huxm@marvell.com> Signed-off-by:Brian Norris <briannorris@chromium.org> Reviewed-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Reviewed-by:
Ganapathi Bhat <gbhat@marvell.com> Signed-off-by:
-
David S. Miller authored
Manish Chopra says: ==================== qed/qede: Enhancements This patch series adds these below features support in qed/qede 1) Ntuple filter configuration [via ethtool -n/N] 2) EEE (energy efficient ethernet) support [ethtool --set-eee/show-eee] 3) Coalescing configuration support for VFs [via ethtool -c/C] Please consider applying this to "net-next" V1->V2: * Fixes below Kbuild test robot warning. drivers/net//ethernet/qlogic/qed/qed_l2.c: In function 'qed_get_queue_coalesce': drivers/net//ethernet/qlogic/qed/qed_l2.c:2137:8: error: implicit declaration of function 'qed_vf_pf_get_coalesce' [-Werror=implicit-function-declaration] ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Rahul Verma authored
Maximum coalesce per Rx/Tx queue is extended from 255 to 511. Signed-off-by:
Rahul Verma <rahul.verma@cavium.com> Signed-off-by:
Yuval Mintz <yuval.mintz@cavium.com> Signed-off-by:
-
Rahul Verma authored
Retrieve the actual coalesce value from hardware for every Rx/Tx queue, instead of Rx/Tx coalesce value cached during set coalesce. Signed-off-by:
-
Rahul Verma authored
This patch add the ethtool support to set RX/Tx coalesce value to the VF associated Rx/Tx queues. Signed-off-by:
-
Sudarsana Reddy Kalluru authored
The patch adds ethtool callback implementations for querying/configuring the Energy Efficient Ethernet (EEE) parameters. Signed-off-by:
Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by:
-
Sudarsana Reddy Kalluru authored
The patch adds required driver support for reading/configuring the Energy Efficient Ethernet (EEE) parameters. Signed-off-by:
-
Chopra, Manish authored
This patch adds support for adding and deleting rx flow classification rules. Using this user can classify RX flow constituting of TCP/UDP 4-tuples [src_ip/dst_ip and src_port/dst_port] to be steered on a given RX queue Signed-off-by:
Manish Chopra <manish.chopra@cavium.com> Signed-off-by:
-
Chopra, Manish authored
This patch adds support for ethtool getter APIs to query RX flow classification rules. Signed-off-by:
-
- 26 Jul, 2017 19 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== 40GbE Intel Wired LAN Driver Updates 2017-07-25 This series contains updates to i40e and i40evf only. Gustavo Silva fixes a variable assignment, where the incorrect variable was being used to store the error parameter. Carolyn provides a fix for a problem found in systems when entering S4 state, by ensuring that the misc vector's IRQ is disabled as well. Jake removes the single-threaded restriction on the module workqueue, which was causing issues with events such as CORER. Does some future proofing, by changing how the driver displays the UDP tunnel type. Paul adds a retry in releasing resources if the admin queue times out during the first attempt to release the resources. Jesse fixes up references to 32bit timspec, since there are a small set of errors on 32 bit, so we need to be using the right calls for dealing with timespec64 variables. Cleaned up code indentation and corrected an "if" conditional check, as well as making the code flow more clear. Cast or changed the types to remove warnings for comparing signed and unsigned types. Adds missing includes in i40evf, which were being used but were not being directly included. Daniel Borkmann fixes i40e to fill the XDP prog_id with the id just like other XDP enabled drivers, so that on dump we can retrieve the attached program based on the id and dump BPF insns, opcodes, etc back to user space. Tushar Dave adds le32_to_cpu while evaluating the hardware descriptor fields, since they are in little-endian format. Also removed unnecessary "__packed" to a couple of i40evf structures. Stefan Assmann fixes an issue when an administratively set MAC was set and should now be switched back to 00:00:00:00:00:00, the pf_set_mac flag is not being toggled back to false. ==================== Signed-off-by: -
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== 10GbE Intel Wired LAN Driver Updates 2017-07-25 This series contains updates to ixgbe only. Tony provides all of the changes in the series, starting with adding a check to ensure that adding a MAC filter was successful, before setting the MACVLAN. In order to receive notifications of link configurations of the external PHY and support the configuration of the internal iXFI link on X552 devices, Tony enables LASI interrupts. Update the iXFI driver code flow, since the MAC register NW_MNG_IF_SEL fields have been redefined for X553 devices, so add MAC checks for iXFI flows. Added additional checks for flow control autonegotiation, since it is not support for X553 fiber and XFI devices. v2: removed unnecessary parens noticed by David Miller in patch 6 of the series. v3: dropped patch 6 of the original series, while we work out a more generic solution for malicious driver detection (MDD) support. v4: updated patch 1 of the series with the comments from Joe Perches which were: - switched logic to return on error - return 0 on success - declare retval as an integer ==================== Signed-off-by: -
Jakub Kicinski authored
Add a new target to install the bpf.h header to $(prefix)/include/bpf/ directory. This is necessary to build standalone applications using libbpf, without the need to clone the kernel sources and point to them. Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Arnd Bergmann authored
gcc warns that the device name might overflow: drivers/net/hamradio/dmascc.c: In function 'dmascc_init': drivers/net/hamradio/dmascc.c:584:22: error: 'sprintf' may write a terminating nul past the end of the destination [-Werror=format-overflow=] sprintf(dev->name, "dmascc%i", 2 * n + i); drivers/net/hamradio/dmascc.c:584:3: note: 'sprintf' output between 8 and 17 bytes into a destination of size 16 sprintf(dev->name, "dmascc%i", 2 * n + i); >From the static data in this file, I can tell that the index is strictly limited to 16, so it won't overflow. This simply changes the sprintf() to snprintf(), which is a good idea in general, and shuts up this warning. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Stefan Assmann authored
When an administratively set MAC was previously set and should now be switched back to 00:00:00:00:00:00 the pf_set_mac flag did not get toggled back to false. As a result VFs were still treated as if an administratively set MAC was present. Signed-off-by:
Stefan Assmann <sassmann@kpanic.de> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Tushar Dave authored
This is similar to 'commit 9588397d ("i40e: remove unnecessary __packed")' to avoid unaligned access. Signed-off-by:
Tushar Dave <tushar.n.dave@oracle.com> Tested-by:
-
Tushar Dave authored
i40e hardware descriptor fields are in little-endian format. Driver must use le32_to_cpu while evaluating these fields otherwise on big-endian arch we end up evaluating incorrect values, cause errors like: i40evf 0000:03:0a.0: Expected response 24 from PF, received 402653184 i40evf 0000:03:0a.1: Expected response 7 from PF, received 117440512 Signed-off-by:
Shannon Nelson <shannon.nelson@oracle.com> Tested-by:
-
Daniel Borkmann authored
Fill the XDP prog_id with the id just like we do in other XDP enabled drivers such as ixgbe. This is needed so that on dump we can retrieve the attached program based on the id, and dump BPF insns, opcodes, etc back to user space. Only XDP driver missing this is currently i40e. Signed-off-by:
John Fastabend <john.fastabend@gmail.com> Acked-by:
Alexander Duyck <alexander.h.duyck@intel.com> Tested-by:
-
Jesse Brandeburg authored
These includes were all being used in the driver, but weren't being directly included. Since the current advised method is to directly include anything that you need, this implements that. Signed-off-by:
Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by:
-
Jacob Keller authored
The i40e driver attempts to display the UDP tunnel name by doing a check against the type, where for non-zero types we use "vxlan" and for zero type we use "geneve". This is not future proof, because if new tunnel types get added, we'll incorrectly label them. It also depends on the value of UDP_TUNNEL_TYPE_GENEVE == 0, which is brittle. Instead, replace this with a function that can return a constant string depending on the type. For now we'll use "unknown" for types we don't know about, and we can expand this in the future if new types get added. Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Tested-by:
-
Jesse Brandeburg authored
Compiler reported several places where driver compared signed and unsigned types. Cast or change the types to remove the warnings. Signed-off-by:
-
Jesse Brandeburg authored
This just reorders some local vars and makes the code flow clearer. Signed-off-by:
-
Jesse Brandeburg authored
The compiler warned on an oddly indented bit of code, and when investigating that, noted that the functions themselves had an odd flow. The if condition was checked, and would exclude a call to AQ, but then the aq_ret would be checked unconditionally which just looks really weird, and is likely to cause objections. Signed-off-by:
-
Jesse Brandeburg authored
As it turns out there was only a small set of errors on 32 bit, and we just needed to be using the right calls for dealing with timespec64 variables. Signed-off-by:
-
Paul M Stillwell Jr authored
There are some rare cases where the release resource call will return an admin Q timeout. In these cases the code needs to try to release the resource again until it succeeds or it times out. Signed-off-by:
Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com> Tested-by:
-
Jacob Keller authored
During certain events such as a CORER, multiple devices will run a work task to handle some cleanup. This can cause issues due to a single-threaded workqueue which can mean that a device doesn't cleanup in time. Prevent this by removing the single-threaded restriction on the module workqueue. This avoids the need to add more complex yielding logic in our service task routine. This is also similar to what other drivers such as fm10k do. Signed-off-by:
-
Carolyn Wyborny authored
This patch fixes a problem found in systems when entering S4 state. This patch fixes the problem by ensuring that the misc vector's IRQ is disabled as well. Without this patch a stack trace can be seen upon entering S4 state. Signed-off-by:
Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by:
-
Gustavo A R Silva authored
Fix incorrect variable assignment. Based on line 1511: aq_ret = I40_ERR_PARAM; the correct variable to be used in this instance is aq_ret instead of ret. Also, variable ret is updated at line 1602 just before return, so assigning a value to this variable in this code block is useless. Addresses-Coverity-ID: 1397693 Signed-off-by:
Gustavo A R Silva <garsilva@embeddedor.com> Acked-by:
-
Arnd Bergmann authored
After removing the reset function, the freeze and restore functions are now unused when CONFIG_PM_SLEEP is disabled: drivers/net/virtio_net.c:1881:12: error: 'virtnet_restore_up' defined but not used [-Werror=unused-function] static int virtnet_restore_up(struct virtio_device *vdev) drivers/net/virtio_net.c:1859:13: error: 'virtnet_freeze_down' defined but not used [-Werror=unused-function] static void virtnet_freeze_down(struct virtio_device *vdev) A more robust way to do this is to remove the #ifdef around the callers and instead mark them as __maybe_unused. The compiler will now just silently drop the unused code. Fixes: 4941d472 ("virtio-net: do not reset during XDP set") Signed-off-by:
Jason Wang <jasowang@redhat.com> Signed-off-by:
-
- 25 Jul, 2017 1 commit
-
-
Tony Nguyen authored
Flow control autonegotiation is not supported for XFI. Make sure that ixgbe_device_supports_autoneg_fc() returns false and hw->fc.disable_fc_autoneg is set to true to avoid running the fc_autoneg function for that device. Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by:
Emil Tantilov <emil.s.tantilov@intel.com> Tested-by:
-
