Add proper error handling for hdmi_probe_pdata(). This will cause
EPROBE_DEFER to be properly passed upwards, causing the HDMI driver to be
probed again later if a resource was missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Add proper error handling for rfbi_probe_pdata(). This will cause
EPROBE_DEFER to be properly passed upwards, causing the RFBI driver to be
probed again later if a resource was missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Add proper error handling for dsi_probe_pdata(). This will cause
EPROBE_DEFER to be properly passed upwards, causing the DSI driver to be
probed again later if a resource was missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Add proper error handling for sdi_probe_pdata(). This will cause
EPROBE_DEFER to be properly passed upwards, causing the SDI driver to be
probed again later if a resource was missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Add proper error handling for dpi_probe_pdata(). This will cause
EPROBE_DEFER to be properly passed upwards, causing the DPI driver to be
probed again later if a resource was missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Use platform_driver_register() instead of platform_driver_probe() so
that we can support EPROBE_DEFER.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Use platform_driver_register() instead of platform_driver_probe() so
that we can support EPROBE_DEFER.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Use platform_driver_register() instead of platform_driver_probe() so
that we can support EPROBE_DEFER.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Use platform_driver_register() instead of platform_driver_probe() so
that we can support EPROBE_DEFER.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Use platform_driver_register() instead of platform_driver_probe() so
that we can support EPROBE_DEFER.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Use platform_driver_register() instead of platform_driver_probe() so
that we can support EPROBE_DEFER.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

omapfb requires the panel drivers to have been probed when omapfb is
initialized. omapfb does not support insertion of new panels after its
probe. This causes a problem in case omapdss or the panel probes have
been deferred due to EPROBE_DEFER error, as omapfb won't find any
displays.

As a quick fix, this patch changes the omapfb probe so that if omapfb
does not find any displays, it'll return EPROBE_DEFER. This is not
perfect, as with a board with no displays, omapfb will get deferred
forever. Also, if the board has multiple displays, but only some of them
have been probed, omapfb will start and leave the unprobed displays out.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Instead of using platform_driver_probe(), use module_platform_driver()
so that we can support deferred probing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

omapfb requires the panels to have been probed before omapfb's probe. We
currently manage that by having omapfb in late initcall level. However,
a much simpler way is to just change the makefile so that omapfb is
after the panel drivers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Commit 100c8262 (OMAPDSS: DPI: use new
clock calculation code) breaks dpi.c compilation if DSI is not enabled
in the kernel configuration.

Fix compilation by adding dummy inline functions for the ones that dpi.c
references. The functions will never be called, as dpi.c knows that
there is no DSI device available.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Some static structs are not marked as static. Add it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The omapdrm driver currently takes a config/module arg to figure out the number
of crtcs it needs to create. We could create as many crtcs as there are overlay
managers in the DSS hardware, but we don't do that because each crtc eats up
one DSS overlay, and that reduces the number of planes we can attach to a single
crtc.

Since the number of crtcs may be lesser than the number of hardware overlay
managers, we need to figure out which overlay managers to use for our crtcs. The
current approach is to use pipe2chan(), which returns a higher numbered manager
for the crtc.

The problem with this approach is that it assumes that the overlay managers we
choose will connect to the encoders the platform's panels are going to use,
this isn't true, an overlay manager connects only to a few outputs/encoders, and
choosing any overlay manager for our crtc might lead to a situation where the
encoder cannot connect to any of the crtcs we have chosen. For example, an
omap5-panda board has just one hdmi output. If num_crtc is set to 1, with the
current approach, pipe2chan will pick up the LCD2 overlay manager, which cannot
connect to the hdmi encoder at all. The only manager that could have connected
to hdmi was the TV overlay manager.

Therefore, there is a need to choose our overlay managers keeping in mind the
panels we have on that platform. The new approach iterates through all the
available panels, creates encoders and connectors for them, and then tries to
get a suitable overlay manager to create a crtc which can connect to the
encoders.

We use the dispc_channel field in omap_dss_output to retrieve the desired
overlay manager's channel number, we then check whether the manager had already
been assigned to a crtc or not. If it was already assigned to a crtc, we assume
that out of all the encoders which intend use this crtc, only one will run at a
time. If the overlay manager wan't assigned to a crtc till then, we create a
new crtc and link it with the overlay manager.

This approach just looks for the best dispc_channel for each encoder. On DSS HW,
some encoders can connect to multiple overlay managers. Since we don't try
looking for alternate overlay managers, there is a greater possibility that 2
or more encoders end up asking for the same crtc, causing only one encoder to
run at a time.

Also, this approach isn't the most optimal one, it can do either good or bad
depending on the sequence in which the panels/outputs are parsed. The optimal
way would be some sort of back tracking approach, where we improve the set of
managers we use as we iterate through the list of panels/encoders. That's
something left for later.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

When userspace calls SET_PLANE ioctl, drm core takes a reference of the fb and
passes control to the update_plane op defined by the drm driver.

In omapdrm, we have a worker thread which queues framebuffers objects received
from update_plane and displays them at the appropriate time.

It is possible that the framebuffer is destoryed by userspace between the time
of calling the ioctl and apply-worker being scheduled. If this happens, the
apply-worker holds a pointer to a framebuffer which is already destroyed.

Take an extra refernece/unreference of the fb in omap_plane_update() to prevent
this from happening. A reference is taken of the fb passed to update_plane(),
the previous framebuffer (held by plane->fb) is unreferenced. This will prevent
drm from destroying the framebuffer till the time it's unreferenced by the
apply-worker.

This is in addition to the exisitng reference/unreference in update_pin(),
which is taken for the scanout of the plane's current framebuffer, and an
unreference the previous framebuffer.
Signed-off-by: Archit Taneja <archit@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The omapdrm driver requires omapdss panel drivers to expose ops like detect,
set_timings and check_timings. These can be NULL for fixed panel DPI, DBI, DSI
and SDI drivers. At some places, there are no checks to see if the panel driver
has these ops or not, and that leads to a crash.

The following things are done to make fixed panels work:

- The omap_connector's detect function is modified such that it considers panel
  types which are generally fixed panels as always connected(provided the panel
  driver doesn't have a detect op). Hence, the connector corresponding to these
  panels is always in a 'connected' state.

- If a panel driver doesn't have a check_timings op, assume that it supports the
  mode passed to omap_connector_mode_valid(the 'mode_valid' drm helper function)

- The function omap_encoder_update shouldn't really do anything for fixed
  resolution panels, make sure that it calls set_timings only if the panel
  driver has one.
Signed-off-by: Archit Taneja <archit@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

modeset_init iterates through all the registered omapdss devices and has some
initial checks to see if the panel has a driver and the required driver ops for
it to be usable by omapdrm.

The function bails out from modeset_init if a panel doesn't meet the
requirements, and stops the registration of the future panels and encoders which
come after it, that isn't the correct thing to do, we should go through the rest
of the panels. Replace the 'return's with 'continue's.
Signed-off-by: Archit Taneja <archit@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

When not using DSI PLL to generate the pixel clock, but DSS FCK, the
possible pixel clock rates are rather limited. DSS FCK is currently used
on OMAP2 and OMAP3.

When using Beagleboard with a monitor that supports high resolutions,
the clock rates do not match (at least for me) for the monitor's pixel
clocks within the current threshold in the code, which is +/- 1MHz.

This patch widens the search up to +/- 15MHz. The search is done in
steps, i.e. it first tries to find a rather exact clock, than a bit less
exact, etc. so this should not change the cases where a clock was
already found.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

DSS func clock is calculated with prate / div * m. However, the current
omapdss code calculates it with prate * m / div, which yields a slightly
different result when there's a remainder. For example, 432000000 / 14 *
2 = 61714284, but 432000000 * 2 / 14 = 61714285.

In addition to that, the clock framework wants the clock rate given with
clk_set_rate to be higher than the actual (truncated) end result. So, if
prate is 432000000, and div is 14, the real result is 30857142.8571...
We need to call clk_set_rate with 30857143, which gives us a clock of
30857142. That's why we need to use DIV_ROUND_UP() when calling
clk_set_rate.

This patch fixes the clock calculation.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Use devm_clk_get() instead of clk_get() for dss, and for outputs hdmi
and venc. This reduces code and simplifies error handling.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Use dev_pm_ops instead of the deprecated legacy suspend/resume callbacks.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

DISPC on OMAP5 has a more optimised mechanism of asserting Mstandby to achieve
more power savings when DISPC is configured in Smart Standby mode. This
mechanism leads to underflows when multiple DISPC pipes are enabled.

There is a register field which can let us revert to the older mechanism of
asserting Mstandby. Configure this field to prevent underflows.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

When using a DISPC video pipeline to a fetch a NV12 buffer in a 2D container, we
need to set set a doublestride bit in the video pipe's ATTRIBUTES register. This
is needed because the stride for the UV plane(using a 16 bit Tiler container) is
double the stride for the Y plane(using a 8 bit Tiler container) for the 0 or
180 degree views. The ROW_INC register is meant for the Y plane, and the HW will
calculate the row increment needed for the UV plane by using double the stride
value based on whether this bit is set or not.

Set the bit when we are using a 2D Tiler buffer and when rotation is 0 or 180
degrees. The stride value is the same for 90 and 270 degree Tiler views, hence
the bit shouldn't be set.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Increase the DSS_FCLK and DSI_FCLK max supported frequencies, these come because
some frequencies were increased from OMAP5 ES1 to OMAP5 ES2. We support only
OMAP5 ES2 in the kernel, so replace the ES1 values with ES2 values. Increase the
DSI PLL Fint range, this was previously just copied from the OMAP4 param range
struct.

Fix the maximum DSS_FCLK on OMAP2, it's 133 Mhz according to the TRM.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Each version of OMAP has a limitation on the maximum pixel clock frequency
supported by an overlay manager. This limit isn't checked by omapdss. Add
dispc feats for lcd and tv managers and check whether the target timings can
be supported or not.

The pixel clock limitations are actually more complex. They depend on which OPP
OMAP is in, and they also depend on which encoder is the manager connected to.
The OPP dependence is ignored as DSS forces the PM framework to be on OPP100
when DSS is enabled, and the encoder dependencies are ignored by DISPC for now.
These limits should come from the encoder driver.

The OMAP2 TRM doesn't mention the maximum pixel clock limit. This value is left
as half of DSS_FCLK, as OMAP2 requires the PCD to be atleast 2.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Using devm_clk_get cleans up some code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Use PTR_RET function instead of IS_ERR and PTR_ERR.
Patch found using coccinelle.
Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The platform_enable/disable callbacks in board files for VENC omap_dss_device
instances don't do anything. Hence, we can remove these callbacks from the VENC
driver.
Signed-off-by: Archit Taneja <archit@ti.com>

The n8x0 panel driver now manages the gpios required to configure the panel.
This was previously done in panel_n8x0_data's platform_enable/disable callbacks
defined in board files using this panel.

All the board files using this panel now pass the gpio information as platform
data via the panel_n8x0_data struct, which is needed by the panel driver to
configure the gpios connected to the panel. Hence, the uses of
platform_enable/disable ops can be safely removed now.
Signed-off-by: Archit Taneja <archit@ti.com>

The n8x0 panel driver leaves gpio configurations to the platform_enable and
disable calls in the platform's board file. These should happen in the panel
driver itself.

A platform data struct called panel_n8x0_data already exists to hold gpio
numbers and other platform data. However, the gpio requests are expected to be
done in the board file and not the panel driver.

Request all the gpios in the panel driver so that the board files which use
the the panel don't need to do it. This will help in removing the need for the
panel drivers to have platform related callbacks.
Signed-off-by: Archit Taneja <archit@ti.com>

The picodlp panel driver now manages the gpios required to configure the
panel. This was previously done in omap_dss_device's platform_enable/disable
callbacks defined in board files using this panel.

All the board files using this panel now pass the gpio information as platform
data via the panel_generic_dpi_data struct, which is needed by the panel driver
to configure the gpios connected to the panel. Hence, the
platform_enable/disable ops can be safely removed now.
Signed-off-by: Archit Taneja <archit@ti.com>

The picodlp panel driver leaves gpio requests to the platform's board file.
These should happen in the panel driver itself.

A platform data struct called picodlp_panel_data already exists to hold gpio
numbers and other platform data. Request all the gpios in the panel driver so
that the board files which use the the panel don't need to do it.

This will help in removing the need for the panel drivers to have platform
related callbacks.
Signed-off-by: Archit Taneja <archit@ti.com>

The tpo-td043 panel driver now manages the gpios required to configure the panel.
This was previously done in omap_dss_device's platform_enable/disable callbacks
defined in board files using this panel.

All the board files using this panel now pass the gpio information as platform
data via the panel_tpo_td043_data struct, which is needed by the panel driver to
configure the gpios connected to the panel. Hence, the platform_enable/disable
ops can be safely removed now.
Signed-off-by: Archit Taneja <archit@ti.com>

The tpo-td043mtea1 panel driver leaves gpio configurations to the
platform_enable and disable calls in the platform's board file. These should
happen in the panel driver itself.

Create a platform data struct for the panel, this contains the reset gpio
number used by the panel driver, this struct will be passed to the panel driver
as platform data. The driver will request and configure the reset gpio rather
than leaving it to platform callbacks in board files.

This will help in removing the need for the panel drivers to have platform
related callbacks.
Signed-off-by: Archit Taneja <archit@ti.com>

The nec-nl8048 panel driver now manages the gpios required to configure the
panel. This was previously done in omap_dss_device's platform_enable/disable
callbacks defined in board files using this panel.

All the board files using this panel now pass the gpio information as platform
data via the panel_nec_nl8048_data struct, which is needed by the panel driver
to configure the gpios connected to the panel. Hence, the
platform_enable/disable ops can be safely removed now.
Signed-off-by: Archit Taneja <archit@ti.com>

The nec-nl8048hl11-01 panel driver leaves gpio configurations to the
platform_enable and disable calls in the platform's board file. These should
happen in the panel driver itself.

Create a platform data struct for the panel, this contains the gpio numbers
used by the panel driver, this struct will be passed to the panel driver as
platform data. The driver will request and configure these gpios rather than
leaving it to platform callbacks in board files.

This will help in removing the need for the panel drivers to have platform
related callbacks.
Signed-off-by: Archit Taneja <archit@ti.com>