- 04 Feb, 2016 37 commits
-
-
Guillaume Fougnies authored
commit 5a4ff9ec upstream. TEAC UD-501/UD-503/NT-503 fail to switch properly between different rate/format. Similar to 'Playback Design', this patch corrects the invalid clock source error for TEAC products and avoids complete freeze of the usb interface of 503 series. Signed-off-by:
Guillaume Fougnies <guillaume@eulerian.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Takashi Iwai authored
commit 462b3f16 upstream. Some architectures like PowerPC can handle the maximum struct size in an ioctl only up to 13 bits, and struct snd_compr_codec_caps used by SNDRV_COMPRESS_GET_CODEC_CAPS ioctl overflows this limit. This problem was revealed recently by a powerpc change, as it's now treated as a fatal build error. This patch is a stop-gap for that: for architectures with less than 14 bit ioctl struct size, get rid of the handling of the relevant ioctl. We should provide an alternative equivalent ioctl code later, but for now just paper over it. Luckily, the compress API hasn't been used on such architectures, so the impact must be effectively zero. Reviewed-by:
Mark Brown <broonie@kernel.org> Acked-by:
Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by:
-
John Ernberg authored
commit 4152b387 upstream. In certain kernel configurations where the cdc_ether and option drivers are compiled as modules there can occur a race condition in enumeration. This causes the option driver to enumerate the ethernet(wwan) interface as usb-serial interfaces. usb-devices output for the modem: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 5 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1e2d ProdID=0055 Rev=00.00 S: Manufacturer=Cinterion S: Product=AHx C: #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=10mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether I: If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether Signed-off-by:
John Ernberg <john.ernberg@actia.se> Fixes: 1941138e ("USB: added support for Cinterion's products...") Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Lorenzo Pieralisi authored
commit f436b2ac upstream. The Performance Monitors extension is an optional feature of the AArch64 architecture, therefore, in order to access Performance Monitors registers safely, the kernel should detect the architected PMU unit presence through the ID_AA64DFR0_EL1 register PMUVer field before accessing them. This patch implements a guard by reading the ID_AA64DFR0_EL1 register PMUVer field to detect the architected PMU presence and prevent accessing PMU system registers if the Performance Monitors extension is not implemented in the core. Cc: Peter Maydell <peter.maydell@linaro.org> Cc: Mark Rutland <mark.rutland@arm.com> Fixes: 60792ad3 ("arm64: kernel: enforce pmuserenr_el0 initialization and restore") Signed-off-by:
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reported-by:
Guenter Roeck <linux@roeck-us.net> Tested-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Greg Kroah-Hartman authored
commit e03cdf22 upstream. Harald Linden reports that the ftdi_sio driver works properly for the Yaesu SCU-18 cable if the device ids are added to the driver. So let's add them. Reported-by:
Harald Linden <harald.linden@7183.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Takashi Iwai authored
commit da10816e upstream. ALSA OSS sequencer spews a kernel error message ("ALSA: seq_oss: too many applications") when user-space tries to open more than the limit. This means that it can easily fill the log buffer. Since it's merely a normal error, it's safe to suppress it via pr_debug() instead. Signed-off-by:
-
Takashi Iwai authored
commit 59915133 upstream. ALSA sequencer OSS emulation code has a sanity check for currently opened devices, but there is a thinko there, eventually it spews warnings and skips the operation wrongly like: WARNING: CPU: 1 PID: 7573 at sound/core/seq/oss/seq_oss_synth.c:311 Fix this off-by-one error. Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
-
Daniele Palmas authored
commit ff4e2494 upstream. This patch adds support for two PIDs of LE922. Signed-off-by:
Daniele Palmas <dnlplm@gmail.com> Signed-off-by:
-
Vladis Dronov authored
commit cb323213 upstream. The visor driver crashes in clie_5_attach() when a specially crafted USB device without bulk-out endpoint is detected. This fix adds a check that the device has proper configuration expected by the driver. Reported-by:
Ralf Spenneberg <ralf@spenneberg.net> Signed-off-by:
Vladis Dronov <vdronov@redhat.com> Fixes: cfb8da8f ("USB: visor: fix initialisation of UX50/TH55 devices") Signed-off-by:
-
Johan Hovold authored
commit cac9b50b upstream. Fix null-pointer dereference at probe should a (malicious) Treo device lack the expected endpoints. Specifically, the Treo port-setup hack was dereferencing the bulk-in and interrupt-in urbs without first making sure they had been allocated by core. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Peter Dedecker authored
commit f487c54d upstream. Added the USB serial console device ID for IAI Corp. RCB-CV-USB USB to RS485 adaptor. Signed-off-by:
Peter Dedecker <peter.dedecker@hotmail.com> Signed-off-by:
-
Du, Changbin authored
commit d8f00cd6 upstream. In function usb_reset_and_verify_device, the old BOS descriptor may still be used before allocating a new one. (usb_unlocked_disable_lpm function uses it under the situation that it fails to disable lpm.) So we cannot set the udev->bos to NULL before that, just keep what it was. It will be overwrite when allocating a new one. Crash log: BUG: unable to handle kernel NULL pointer dereference at 0000000000000010 IP: [<ffffffff8171f98d>] usb_enable_link_state+0x2d/0x2f0 Call Trace: [<ffffffff8171ed5b>] ? usb_set_lpm_timeout+0x12b/0x140 [<ffffffff8171fcd1>] usb_enable_lpm+0x81/0xa0 [<ffffffff8171fdd8>] usb_disable_lpm+0xa8/0xc0 [<ffffffff8171fe1c>] usb_unlocked_disable_lpm+0x2c/0x50 [<ffffffff81723933>] usb_reset_and_verify_device+0xc3/0x710 [<ffffffff8172c4ed>] ? usb_sg_wait+0x13d/0x190 [<ffffffff81724743>] usb_reset_device+0x133/0x280 [<ffffffff8179ccd1>] usb_stor_port_reset+0x61/0x70 [<ffffffff8179cd68>] usb_stor_invoke_transport+0x88/0x520 Signed-off-by:
Du, Changbin <changbin.du@intel.com> Signed-off-by:
-
Oliver Neukum authored
commit e912e685 upstream. This phone needs to be handled by a specialised firmware tool and is reported to crash irrevocably if cdc-acm takes it. Signed-off-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
-
Lu Baolu authored
commit ffdb1e36 upstream. For Intel 7260 modem, it is needed for host side to send zero packet if the BULK OUT size is equal to USB endpoint max packet length. Otherwise, modem side may still wait for more data and cannot give response to host side. Signed-off-by:
Konrad Leszczynski <konrad.leszczynski@intel.com> Signed-off-by:
Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by:
-
Lu Baolu authored
commit 19454462 upstream. In current acm driver, the bulk-in callback function ignores the URBs unlinked in usb core. This causes unexpected data loss in some cases. For example, runtime suspend entry will unlinked all urbs and set urb->status to -ENOENT even those urbs might have data not processed yet. Hence, data loss occurs. This patch lets bulk-in callback function handle unlinked urbs to avoid data loss. Signed-off-by:
Tang Jian Qiang <jianqiang.tang@intel.com> Signed-off-by:
-
Thorsten Leemhuis authored
commit 6220f4eb upstream. Since Linux 4.0 the CPU fan speed is going up and down on Dell Studio XPS 8000 and 8100 for unknown reasons. The 8100 was already blacklisted in commit a4b45b25 ("hwmon: (dell-smm) Blacklist Dell Studio XPS 8100"). This patch blacklists the XPS 8000. Without further debugging on the affected machine, it is not possible to find the problem. For more details see https://bugzilla.kernel.org/show_bug.cgi?id=100121Signed-off-by:
Thorsten Leemhuis <linux@leemhuis.info> Acked-by:
Pali Rohár <pali.rohar@gmail.com> Signed-off-by:
-
Insu Yun authored
commit 2c3033a0 upstream. In acpiphp_enable_slot(), there is a missing unlock path when error occurred. It needs to be unlocked before returning an error. Signed-off-by:
Insu Yun <wuninsu@gmail.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Hans de Goede authored
commit b186b4dc upstream. The quirk to get "acpi_backlight=vendor" behavior by default on the Dell Inspiron 5737 was added before we started doing "acpi_backlight=native" by default on Win8 ready machines. Since we now avoid using acpi-video as backlight driver on these machines by default (using the native driver instead) we no longer need this quirk. Moreover the vendor driver does not work after a suspend/resume where as the native driver does. This reverts commit 08a56226 (ACPI / video: Add Dell Inspiron 5737 to the blacklist). Link: https://bugzilla.kernel.org/show_bug.cgi?id=111061 Reported-and-tested-by: erusan@gmail.com Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Alex Deucher authored
commit cc78eb22 upstream. Firmware is LE. Need to properly byteswap some of the fields so they are interpreted correctly by the driver on BE systems. Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Christian König authored
commit 78d0e182 upstream. We could pin BOs into invisible VRAM otherwise. v2: make logic more readable as suggested by Michel Signed-off-by:
Michel Dänzer <michel.daenzer@amd.com> Signed-off-by:
-
Alan Modra authored
commit c153693d upstream. PowerPC64 uses the symbol .TOC. much as other targets use _GLOBAL_OFFSET_TABLE_. It identifies the value of the GOT pointer (or in powerpc parlance, the TOC pointer). Global offset tables are generally local to an executable or shared library, or in the kernel, module. Thus it does not make sense for a module to resolve a relocation against .TOC. to the kernel's .TOC. value. A module has its own .TOC., and indeed the powerpc64 module relocation processing ignores the kernel value of .TOC. and instead calculates a module-local value. This patch removes code involved in exporting the kernel .TOC., tweaks modpost to ignore an undefined .TOC., and the module loader to twiddle the section symbol so that .TOC. isn't seen as undefined. Note that if the kernel was compiled with -msingle-pic-base then ELFv2 would not have function global entry code setting up r2. In that case the module call stubs would need to be modified to set up r2 using the kernel .TOC. value, requiring some of this code to be reinstated. mpe: Furthermore a change in binutils master (not yet released) causes the current way we handle the TOC to no longer work when building with MODVERSIONS=y and RELOCATABLE=n. The symptom is that modules can not be loaded due to there being no version found for TOC. Signed-off-by:
Alan Modra <amodra@gmail.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Michel Dänzer authored
commit 9571e1d8 upstream. It can be big, depending on the VM address space size, which is tunable via the vm_size module parameter. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93721Reviewed-by:
-
Thomas Gleixner authored
commit 51cbb524 upstream. As Helge reported for timerfd we have the same issue in itimers. We return remaining time larger than the programmed relative time to user space in case of CONFIG_TIME_LOW_RES=y. Use the proper function to adjust the extra time added in hrtimer_start_range_ns(). Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Helge Deller <deller@gmx.de> Cc: John Stultz <john.stultz@linaro.org> Cc: linux-m68k@lists.linux-m68k.org Cc: dhowells@redhat.com Link: http://lkml.kernel.org/r/20160114164159.528222587@linutronix.deSigned-off-by:
-
Thomas Gleixner authored
commit 572c3917 upstream. As Helge reported for timerfd we have the same issue in posix timers. We return remaining time larger than the programmed relative time to user space in case of CONFIG_TIME_LOW_RES=y. Use the proper function to adjust the extra time added in hrtimer_start_range_ns(). Signed-off-by:
-
Thomas Gleixner authored
commit b62526ed upstream. Helge reported that a relative timer can return a remaining time larger than the programmed relative time on parisc and other architectures which have CONFIG_TIME_LOW_RES set. This happens because we add a jiffie to the resulting expiry time to prevent short timeouts. Use the new function hrtimer_expires_remaining_adjusted() to calculate the remaining time. It takes that extra added time into account for relative timers. Reported-and-tested-by:
Helge Deller <deller@gmx.de> Signed-off-by:
-
Thomas Gleixner authored
commit 203cbf77 upstream. If CONFIG_TIME_LOW_RES is enabled we add a jiffie to the relative timeout to prevent short sleeps, but we do not account for that in interfaces which retrieve the remaining time. Helge observed that timerfd can return a remaining time larger than the relative timeout. That's not expected and breaks userland test programs. Store the information that the timer was armed relative and provide functions to adjust the remaining time. To avoid bloating the hrtimer struct make state a u8, which as a bonus results in better code on x86 at least. Reported-and-tested-by:
-
Ravi Bangoria authored
commit 3caeaa56 upstream. While recording guest samples in host using perf kvm record, it will populate unprocessable sample error, though samples will be recorded properly. While generating report using perf kvm report, no samples will be processed and same error will populate. We have seen this behaviour with upstream perf(4.4-rc3) on x86 and ppc64 hardware. Reason behind this failure is, when it tries to fetch machine from rb_tree of machines, it fails. As a part of tracing a bug, we figured out that this code was incorrectly refactored in commit 54245fdc ("perf session: Remove wrappers to machines__find"). This patch will change the functionality such that if it can't fetch machine in first trial, it will create one node of machine and add that to rb_tree. So next time when it tries to fetch same machine from rb_tree, it won't fail. Actually it was the case before refactoring of code in aforementioned commit. This patch is generated from acme perf/core branch. Below I've mention an example that demonstrate the behaviour before and after applying patch. Before applying patch: [Note: One needs to run guest before recording data in host] ravi@ravi-bangoria:~$ ./perf kvm record -a Warning: 5903 unprocessable samples recorded. Do you have a KVM guest running and not using 'perf kvm'? [ perf record: Captured and wrote 1.409 MB perf.data.guest (285 samples) ] ravi@ravi-bangoria:~$ ./perf kvm report --stdio Warning: 5903 unprocessable samples recorded. Do you have a KVM guest running and not using 'perf kvm'? # To display the perf.data header info, please use --header/--header-only options. # # Total Lost Samples: 0 # # Samples: 285 of event 'cycles' # Event count (approx.): 88715406 # # Overhead Command Shared Object Symbol # ........ ....... ............. ...... # # (For a higher level overview, try: perf report --sort comm,dso) # After applying patch: ravi@ravi-bangoria:~$ ./perf kvm record -a [ perf record: Captured and wrote 1.188 MB perf.data.guest (17 samples) ] ravi@ravi-bangoria:~$ ./perf kvm report --stdio # To display the perf.data header info, please use --header/--header-only options. # # Total Lost Samples: 0 # # Samples: 17 of event 'cycles' # Event count (approx.): 700746 # # Overhead Command Shared Object Symbol # ........ ....... ................ ...................... # 34.19% :5758 [unknown] [g] 0xffffffff818682ab 22.79% :5758 [unknown] [g] 0xffffffff812dc7f8 22.79% :5758 [unknown] [g] 0xffffffff818650d0 14.83% :5758 [unknown] [g] 0xffffffff8161a1b6 2.49% :5758 [unknown] [g] 0xffffffff818692bf 0.48% :5758 [unknown] [g] 0xffffffff81869253 0.05% :5758 [unknown] [g] 0xffffffff81869250 Signed-off-by:
Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com> Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Fixes: 54245fdc ("perf session: Remove wrappers to machines__find") Link: http://lkml.kernel.org/r/1449471302-11283-1-git-send-email-ravi.bangoria@linux.vnet.ibm.comSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Alex Deucher authored
commit e160e4db upstream. Need to make sure smu buffers are pinned on resume. This matches what Fiji does. Reviewed-by:
Junwei Zhang <Jerry.Zhang@amd.com> Reviewed-by:
Ken Wang <Qingqing.Wang@amd.com> Signed-off-by:
-
Thomas Gleixner authored
commit e23b257c upstream. setup_ioapic_dest() calls irqchip->irq_set_affinity() completely unprotected. That's wrong in several aspects: - it opens a race window where irq_set_affinity() can be interrupted and the irq chip left in unconsistent state. - it triggers a lockdep splat when we fix the vector race for 4.3+ because vector lock is taken with interrupts enabled. The proper calling convention is irq descriptor lock held and interrupts disabled. Reported-and-tested-by:
Borislav Petkov <bp@alien8.de> Signed-off-by:
-
Greg Kurz authored
commit b4d7f161 upstream. The get and set operations got exchanged by mistake when moving the code from book3s.c to powerpc.c. Fixes: 3840edc8Signed-off-by:
Greg Kurz <gkurz@linux.vnet.ibm.com> Signed-off-by:
Paul Mackerras <paulus@samba.org> Signed-off-by:
-
Thomas Huth authored
commit 760a7364 upstream. In the old DABR register, the BT (Breakpoint Translation) bit is bit number 61. In the new DAWRX register, the WT (Watchpoint Translation) bit is bit number 59. So to move the DABR-BT bit into the position of the DAWRX-WT bit, it has to be shifted by two, not only by one. This fixes hardware watchpoints in gdb of older guests that only use the H_SET_DABR/X interface instead of the new H_SET_MODE interface. Signed-off-by:
Thomas Huth <thuth@redhat.com> Reviewed-by:
Laurent Vivier <lvivier@redhat.com> Reviewed-by:
David Gibson <david@gibson.dropbear.id.au> Signed-off-by:
-
Lars-Peter Clausen authored
commit d590faf9 upstream. The SPI tx and rx buffers are both supposed to be scan_bytes amount of bytes large and a common allocation is used to allocate both buffers. This puts the beginning of the tx buffer scan_bytes bytes after the rx buffer. The initialization of the tx buffer pointer is done adding scan_bytes to the beginning of the rx buffer, but since the rx buffer is of type __be16 this will actually add two times as much and the tx buffer ends up pointing after the allocated buffer. Fix this by using scan_count, which is scan_bytes / 2, instead of scan_bytes when initializing the tx buffer pointer. Fixes: aacff892 ("staging:iio:adis: Preallocate transfer message") Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Joe Jin authored
commit ca88ea12 upstream. Sometimes xennet_create_queues() may failed to created all requested queues, we need to update num_queues to real created to avoid NULL pointer dereference. Signed-off-by:
Joe Jin <joe.jin@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Wei Liu <wei.liu2@citrix.com> Cc: Ian Campbell <ian.campbell@citrix.com> Cc: David S. Miller <davem@davemloft.net> Reviewed-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Wei Liu authored
commit 32a84405 upstream. Originally that parameter was always reset to num_online_cpus during module initialisation, which renders it useless. The fix is to only set max_queues to num_online_cpus when user has not provided a value. Signed-off-by:
Wei Liu <wei.liu2@citrix.com> Cc: David Vrabel <david.vrabel@citrix.com> Reviewed-by:
David Vrabel <david.vrabel@citrix.com> Tested-by:
-
Wei Liu authored
commit 4c82ac3c upstream. Originally that parameter was always reset to num_online_cpus during module initialisation, which renders it useless. The fix is to only set max_queues to num_online_cpus when user has not provided a value. Reported-by:
Johnny Strom <johnny.strom@linuxsolutions.fi> Signed-off-by:
Ian Campbell <ian.campbell@citrix.com> Signed-off-by:
-
Karl Heiss authored
[ Upstream commit 635682a1 ] A case can occur when sctp_accept() is called by the user during a heartbeat timeout event after the 4-way handshake. Since sctp_assoc_migrate() changes both assoc->base.sk and assoc->ep, the bh_sock_lock in sctp_generate_heartbeat_event() will be taken with the listening socket but released with the new association socket. The result is a deadlock on any future attempts to take the listening socket lock. Note that this race can occur with other SCTP timeouts that take the bh_lock_sock() in the event sctp_accept() is called. BUG: soft lockup - CPU#9 stuck for 67s! [swapper:0] ... RIP: 0010:[<ffffffff8152d48e>] [<ffffffff8152d48e>] _spin_lock+0x1e/0x30 RSP: 0018:ffff880028323b20 EFLAGS: 00000206 RAX: 0000000000000002 RBX: ffff880028323b20 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffff880028323be0 RDI: ffff8804632c4b48 RBP: ffffffff8100bb93 R08: 0000000000000000 R09: 0000000000000000 R10: ffff880610662280 R11: 0000000000000100 R12: ffff880028323aa0 R13: ffff8804383c3880 R14: ffff880028323a90 R15: ffffffff81534225 FS: 0000000000000000(0000) GS:ffff880028320000(0000) knlGS:0000000000000000 CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b CR2: 00000000006df528 CR3: 0000000001a85000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process swapper (pid: 0, threadinfo ffff880616b70000, task ffff880616b6cab0) Stack: ffff880028323c40 ffffffffa01c2582 ffff880614cfb020 0000000000000000 <d> 0100000000000000 00000014383a6c44 ffff8804383c3880 ffff880614e93c00 <d> ffff880614e93c00 0000000000000000 ffff8804632c4b00 ffff8804383c38b8 Call Trace: <IRQ> [<ffffffffa01c2582>] ? sctp_rcv+0x492/0xa10 [sctp] [<ffffffff8148c559>] ? nf_iterate+0x69/0xb0 [<ffffffff814974a0>] ? ip_local_deliver_finish+0x0/0x2d0 [<ffffffff8148c716>] ? nf_hook_slow+0x76/0x120 [<ffffffff814974a0>] ? ip_local_deliver_finish+0x0/0x2d0 [<ffffffff8149757d>] ? ip_local_deliver_finish+0xdd/0x2d0 [<ffffffff81497808>] ? ip_local_deliver+0x98/0xa0 [<ffffffff81496ccd>] ? ip_rcv_finish+0x12d/0x440 [<ffffffff81497255>] ? ip_rcv+0x275/0x350 [<ffffffff8145cfeb>] ? __netif_receive_skb+0x4ab/0x750 ... With lockdep debugging: ===================================== [ BUG: bad unlock balance detected! ] ------------------------------------- CslRx/12087 is trying to release lock (slock-AF_INET) at: [<ffffffffa01bcae0>] sctp_generate_timeout_event+0x40/0xe0 [sctp] but there are no more locks to release! other info that might help us debug this: 2 locks held by CslRx/12087: #0: (&asoc->timers[i]){+.-...}, at: [<ffffffff8108ce1f>] run_timer_softirq+0x16f/0x3e0 #1: (slock-AF_INET){+.-...}, at: [<ffffffffa01bcac3>] sctp_generate_timeout_event+0x23/0xe0 [sctp] Ensure the socket taken is also the same one that is released by saving a copy of the socket before entering the timeout event critical section. Signed-off-by:
Karl Heiss <kheiss@gmail.com> Signed-off-by:
-
Sean O. Stalley authored
commit ad82362b upstream. Add a wrapper function for dma_pool_alloc() to get zeroed memory. Signed-off-by:
Sean O. Stalley <sean.stalley@intel.com> Cc: Vinod Koul <vinod.koul@intel.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Gilles Muller <Gilles.Muller@lip6.fr> Cc: Nicolas Palix <nicolas.palix@imag.fr> Cc: Michal Marek <mmarek@suse.cz> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> [ kamal: 4.2-stable prereq for 27bc944 dmaengine: bcm2835-dma: Convert to use DMA pool ] Signed-off-by:
-
- 01 Feb, 2016 2 commits
-
-
Kamal Mostafa authored
This reverts commit 22140f9f. Not suitable for 4.2-stable (no SWAPPER_BLOCK_SIZE definition). Signed-off-by:
-
Kamal Mostafa authored
Signed-off-by:
-
- 27 Jan, 2016 1 commit
-
-
Eric Dumazet authored
[ Upstream commit 34ae6a1a ] When a tunnel decapsulates the outer header, it has to comply with RFC 6080 and eventually propagate CE mark into inner header. It turns out IP6_ECN_set_ce() does not correctly update skb->csum for CHECKSUM_COMPLETE packets, triggering infamous "hw csum failure" messages and stack traces. Signed-off-by:
Eric Dumazet <edumazet@google.com> Acked-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
