- 18 Dec, 2013 39 commits
-
-
Antti Palosaari authored
PCTV 461e requires that small delay. Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
Mauro Carvalho Chehab <m.chehab@samsung.com>
-
Antti Palosaari authored
New chip version, which is very similar than EM28174. Signed-off-by:
-
Josh Wu authored
In the ISI driver it reads the config register to get original value, then set the correct FRATE_DIV and YCC_SWAP_MODE directly. This will cause some bits overlap. So we need to clear these bits first, then set correct value. This patch fix it. Signed-off-by:
Josh Wu <josh.wu@atmel.com> Acked-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Laurent Pinchart authored
The ISI_CFG2.YCC_SWAP field controls color component ordering. The datasheet lists the following orderings for the memory formats. YCC_SWAP Byte 0 Byte 1 Byte 2 Byte 3 00: Default Cb(i) Y(i) Cr(i) Y(i+1) 01: Mode1 Cr(i) Y(i) Cb(i) Y(i+1) 10: Mode2 Y(i) Cb(i) Y(i+1) Cr(i) 11: Mode3 Y(i) Cr(i) Y(i+1) Cb(i) This is based on a sensor format set to CbYCrY (UYVY). The driver hardcodes the output memory format to YUYV, configure the ordering accordingly. Signed-off-by:
-
Laurent Pinchart authored
ISI_MCK is the sensor master clock. It should be handled by the sensor driver directly, as the ISI has no use for that clock. Make the clock optional here while platforms transition to the correct model. Signed-off-by:
-
Laurent Pinchart authored
The queue setup operation isn't the right place to reset the ISI. Move the reset call to the start streaming operation. Signed-off-by:
-
Laurent Pinchart authored
The PCLK and MCK clocks are prepared and unprepared at probe and remove time. Clock (un)preparation isn't needed before enabling/disabling the clocks, and the enable/disable operation happen in non-atomic context. We can thus defer (un)preparation to enable/disable time. Signed-off-by:
-
Laurent Pinchart authored
This simplifies error and cleanup code paths. Signed-off-by:
-
Josh Wu authored
when a userspace applications calls the VIDIOC_STREAMON ioctl. The V4L2 core calls the soc_camera_streamon function, which is responsible for starting the video stream. It does so by first starting the atmel-isi host by a call to the vb2_streamon function, and then starting the sensor by a call to the video.s_stream sensor subdev operation. That means we wait for a SOF in start_streaming() before call sensor's s_stream(). It is possible no VSYNC interrupt arrive as the sensor hasn't been started yet. To avoid such case, this patch remove the code to wait for the VSYNC interrupt. And such code is not necessary. Reported-by:
-
Hans Verkuil authored
Fix the non-whitespace checkpatch errors/warnings. Replace msleep with usleep_range and the jiffies comparison with time_is_after_jiffies(). Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Acked-by:
Eduardo Valentin <edubezval@gmail.com> Acked-by:
Dinesh Ram <dinesh.ram@cern.ch> Signed-off-by:
-
Hans Verkuil authored
Fix most whitespace-related checkpatch errors/warnings. Signed-off-by:
-
Eduardo Valentin authored
Print the PN value, useful to check what chip the dev board has. Signed-off-by:
-
Hans Verkuil authored
si4713_set_rds_radio_text will overwrite the terminating zero at the end of the rds radio text string in order to send out a carriage return as per the RDS spec. Use a separate char buffer for the CR instead of corrupting the control string. Signed-off-by:
-
Dinesh Ram authored
The supply list is needed by the platform driver, but not by the usb driver. So this information belongs to the platform data and should not be hardcoded in the subdevice driver. Signed-off-by:
-
Dinesh Ram authored
Hans Verkuil <hverkuil@xs4all.nl> will maintain the USB driver for si4713 Signed-off-by:
-
Dinesh Ram authored
This is the USB driver for the Silicon Labs development board. It contains the Si4713 FM transmitter chip. Signed-off-by:
-
Dinesh Ram authored
The Si4713 development board contains a Si4713 FM transmitter chip and is handled by the radio-usb-si4713 driver. The board reports itself as (10c4:8244) Cygnal Integrated Products, Inc. and misidentifies itself as a HID device in its USB interface descriptor. This patch ignores this device as an HID device and hence loads the custom driver. Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Acked-by:
-
Dinesh Ram authored
In the si4713_tx_tune_power() method, the args array element 'power' can take values between SI4713_MIN_POWER and SI4713_MAX_POWER. power = 0 is also valid. All the values (0 > power < SI4713_MIN_POWER) are illegal and hence are all mapped to SI4713_MIN_POWER. Signed-off-by:
-
Dinesh Ram authored
Moved the header <linux/regulator/consumer.h> from si4713.c to si4713.h Signed-off-by:
-
Dinesh Ram authored
Checks have been introduced at several places in the code to test if an interrupt is set or not. For devices which do not use the interrupt, to get a valid response, within a specified timeout, the device is polled instead. Signed-off-by:
-
Dinesh Ram authored
Added a new si4713 directory which will contain all si4713 related files. Also updated Makefile and Kconfig Signed-off-by:
-
Lisa Nguyen authored
Rewrite the return statement in vpfe_video.c. This will prevent the checkpatch.pl script from generating a warning saying to remove () from this particular return statement. Signed-off-by:
Lisa Nguyen <lisa@xenapiadmin.com> Acked-by:
Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by:
-
Lisa Nguyen authored
Remove unnecessary spaces before semicolons to meet kernel coding style. Signed-off-by:
-
Laurent Pinchart authored
The v4l2_of_get_remote_port() function acquires a reference to an endpoint node through a phandle and then returns the node's parent, without dropping the reference to the endpoint node. Fix it. Signed-off-by:
Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by:
-
Laurent Pinchart authored
The field isn't set when parsing the endpoint. Remove it. Signed-off-by:
-
Laurent Pinchart authored
When CONFIG_OF is not defined the v4l2_of_parse_endpoint() function is defined as a stub that returns -ENOSYS. Make the real function return an integer as well to be able to differentiate between the two cases. Signed-off-by:
-
Laurent Pinchart authored
A missing break resulted in all done buffers being flagged with V4L2_BUF_FLAG_QUEUED. Fix it. Signed-off-by:
Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by:
-
Laurent Pinchart authored
Replace devm_request_mem_region() and devm_ioremap_nocache() with devm_ioremap_resource(). The behaviour remains the same and the code is simplified. Signed-off-by:
-
Sylwester Nawrocki authored
The clock core code is going to be modified so clk_get() takes reference on the clock provider module. Until the potential circular reference issue is properly addressed, we pass NULL as the first argument to clk_register(), in order to disallow sub-devices taking a reference on the ISP module back trough clk_get(). This should prevent locking the modules in memory. Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Acked-by:
-
Jacek Anaszewski authored
This patch adds proper initialization of the in-driver cached state of JPEG controls with V4L2 core. Signed-off-by:
Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by:
-
Jacek Anaszewski authored
s5p_jpeg_device_run and s5p_jpeg_runtime_resume callbacks should have spin_lock protection as they alter device registers. Signed-off-by:
-
Jacek Anaszewski authored
Standard suspend/resume path is called after runtime resume of the given device, so suspend/resume callbacks must do all clock management done also by runtime pm to allow for proper power domain shutdown. Moreover, JPEG clock is enabled from probe function but is is not necessary. This patch also moves control of jpeg clock to runtime_pm callbacks. Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Seung-Woo Kim <sw0312.kim@samsung.com> Signed-off-by:
-
Jacek Anaszewski authored
Signed-off-by:
-
Jacek Anaszewski authored
Aligning capture queue image dimensions while enqueuing output queue doesn't make a sense as the S_FMT ioctl might have not been called for the capture queue until that moment, whereas it is required to know capture format as the type of alignment heavily depends on it. Signed-off-by:
-
Jacek Anaszewski authored
The aim of the condition is ensuring that the bytesperline value set by the user space application is proper for the given format and adjusting it if isn't. As the depth value of the format description entry is expressed in bits then the bytesperline value needs to be divided, not multiplied, by that value to get the number of bytes required to store single line of image samples. Signed-off-by:
-
Jacek Anaszewski authored
Output samples during decoding phase for the YUV 4:2:0 format are arranged in the manner compatible with 2-planar NV12, not 3-planar YUV420 fourcc. Signed-off-by:
-
Jacek Anaszewski authored
Reorder quantization tables so that their elements are arranged in the manner reflecting compression quality level that is in accordance with V4L2 documentation, i.e. the larger value of the V4L2_CID_JPEG_COMPRESSION_QUALITY control the better image quality, and thus lower compression quality. The modification allows also to get rid of reverse logic in the s_ctrl callback while assigning user space value to the ctx->compr_quality variable. Signed-off-by:
-
Sylwester Nawrocki authored
This patch enables the JPEG codec on S5PV210 and Exynos4210 SoCs. There are some differences in newer versions of the JPEG codec IP on SoCs like Exynos4x12 and Exynos5 series and support for them will be added in subsequent patches. Signed-off-by:
Stephen Warren <swarren@nvidia.com> Signed-off-by:
-
Seung-Woo Kim authored
It is hard to distinguish between decoder and encoder video device because their names are same. So this patch fixes the names. Signed-off-by:
-
- 13 Dec, 2013 1 commit
-
-
Mauro Carvalho Chehab authored
Merge the media fixes merged upstream for v3.13-rc4 * upstream-fixes: (30 commits) [media] videobuf2-dma-sg: fix possible memory leak [media] vb2: regression fix: always set length field. [media] mt9p031: Include linux/of.h header [media] rtl2830: add parent for I2C adapter [media] media: marvell-ccic: use devm to release clk [media] ths7303: Declare as static a private function [media] em28xx-video: Swap release order to avoid lock nesting [media] usbtv: Add support for PAL video source [media] media_tree: Fix spelling errors [media] videobuf2: Add support for file access mode flags for DMABUF exporting [media] radio-shark2: Mark shark_resume_leds() inline to kill compiler warning [media] radio-shark: Mark shark_resume_leds() inline to kill compiler warning [media] af9035: unlock on error in af9035_i2c_master_xfer() [media] af9033: fix broken I2C [media] v4l: omap3isp: Don't check for missing get_fmt op on remote subdev [media] af9035: fix broken I2C and USB I/O [media] wm8775: fix broken audio routing [media] marvell-ccic: drop resource free in driver remove [media] tef6862/radio-tea5764: actually assign clamp result [media] cx231xx: use after free on error path in probe ...
-
