The current code reports a link as up if all devices (except a few
blacklisted ones) report the link as up. This breaks Aquantia AQCS109
for lower speeds because on this PHY the PCS link status reflects a
10G link only. For Marvell there's a similar issue, therefore PHYXS
device isn't checked.

There may be more PHYs where depending on the mode the link status
of only selected devices is relevant.

For now it seems to be sufficient to check the link status of the
PMAPMD device only. Leave the loop in the code to be prepared in
case we have to add functionality to check more than one device,
depending on the mode.

Successfully tested on a board with an AQCS109.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: switchdev.h inclusion removal

This targets a few drivers that no longer to have net/switchdev.h
included.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This is no longer necessary after eca59f69 ("net: Remove support for bridge bypass ndos from stacked devices")
Suggested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is no longer necessary after a5084bb7 ("nfp: Implement
ndo_get_port_parent_id()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

eth_change_mtu() is not needed any more, the networking subsystem will
call it automatically when this callback is not implemented.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The way to define __ETHTOOL_LINK_MODE_MASK_NBITS seems to be overly
complicated, go with a standard approach instead.
Whilst we're at it, move the comment to the right place.

v2:
- rebased
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andy Roulin says:

====================
net: protodown support for macvlan and vxlan

This patch series adds dev_change_proto_down_generic, a generic
implementation of ndo_change_proto_down, which sets the netdev carrier
state according to the new proto_down value.

This handler adds the ability to set protodown on macvlan and vxlan
interfaces in a generic way for use by control protocols like VRRPD.

Patch (1) introduces the handler in net/code/dev.c. Patch (2) and (3) add
support for change_proto_down in macvlan and vxlan drivers, respectively,
using the new function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add ndo_change_proto_down support through dev_change_proto_down_generic
for use by control protocols like VRRPD.
Signed-off-by: Andy Roulin <aroulin@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add ndo_change_proto_down support through dev_change_proto_down_generic
for use by control protocols like VRRPD.
Signed-off-by: Andy Roulin <aroulin@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce dev_change_proto_down_generic, a generic ndo_change_proto_down
implementation, which sets the netdev carrier state according to proto_down.

This adds the ability to set protodown on vxlan and macvlan devices in a
generic way for use by control protocols like VRRPD.
Signed-off-by: Andy Roulin <aroulin@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vlad Buslov says:

====================
Add tests for unlocked flower classifier implementation

Implement tests for tdc testsuite to verify concurrent rules update with
rtnl-unlocked flower classifier implementation. The goal of these tests
is to verify general flower classifier correctness by updating filters
on same classifier instance in parallel and to verify its atomicity by
concurrently updating filters in same handle range. All three filter
update operations (add, replace, delete) are tested.

Existing script tdc_batch.py is re-used for batch file generation. It is
extended with several optional CLI arguments that are needed for
concurrency tests. Thin wrapper tdc_multibatch.py is implemented on top
of tdc_batch.py to simplify its usage when generating multiple batch
files for several test configurations.

Parallelism in tests is implemented by running multiple instances of tc
in batch mode with xargs tool. Xargs is chosen for its ease of use and
because it is available by default on most modern Linux distributions.
====================
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement test that runs 5 instances of tc replace filter in parallel with
5 instances of tc del filter from same tp instance. Each instance uses its
own filter handle and key range.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement test that runs 5 instances of tc add filter in parallel with 5
instances of tc del filter from same tp instance. Each instance uses its
own filter handle and key range.

Extend tdc_multibatch.py with additional options required to implement the
test: common prefix for all generated batch files, first value of filter
handle range, MAC address prefix modifier. These are necessary to allow
creating batch files with unique keys and handle ranges with multiple
invocation of tdc_multibatch.py helper script.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement test that verifies concurrent deletion of rules by executing 10
tc instances that delete flower filters in same handle range. In this case
only one tc instance succeeds in deleting a filter with particular handle.
To mitigate expected failures of all other instances, run tc with 'force'
option to continue processing batch file in case of errors and expect xargs
to return code '123' that indicates that invocation of command(s) exited
with error in range 1-125.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement test that verifies concurrent replacement of rules by executing
10 tc instances that replace flower filters in same handle range.

Extend tdc_multibatch.py script with new optional CLI argument that is used
to generate all batch files with same filter handle range.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement test that verifies parallel rules replacement by adding 1 million
flower filters and then replacing them with 10 concurrent tc instances.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement test that verifies parallel rules deletion by adding 1 million
flower filters and then deleting them with 10 concurrent tc instances.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement test that verifies parallel rules insertion by adding 1 million
flower filters with 10 concurrent tc instances. Put it to standalone
'concurrency' category.

Implement tdc_multibatch.py helper script that is used to generate multiple
batch files for concurrent tc execution. Extend config with new 'BATCH_DIR'
variable to specify temporary output directory that is used to store batch
files generated by tdc_multibatch.py.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend tdc_batch.py with several optional CLI arguments that are used for
implementation of concurrency tests in following patches in this set:

- Add optional argument to specify range of filter handles used in batch
  file [fitler_handle, filter_handle+number). This is needed for testing
  filter deletion where it is necessary to know exact handles of configured
  filters.

- Add optional argument to specify filter operation type (possible values
  are ['add', 'del', 'replace']) instead of hardcoded "add" value. This
  allows generation of batches for filter addition, deletion and
  replacement.

- Add optional argument to allow user to change mac address prefix that is
  used for all filters in batch. This is necessary to allow generating
  multiple batches with unique flower classifier keys.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qdisc_pkt_len_init expects transport_header to be set for GSO packets.
Patch [1] skips transport_header validation for GSO packets that don't
have network_header set at the moment of calling virtio_net_hdr_to_skb,
and allows them to pass into the stack. After patch [2] no placeholder
value is assigned to transport_header if dissection fails, so this patch
adds a check to the place where the value of transport_header is used.

[1] https://patchwork.ozlabs.org/patch/1044429/
[2] https://patchwork.ozlabs.org/patch/1046122/Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add some phylink documentation to the networking book detailing how
to convert network drivers from phylib to phylink.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

A detail for mac_config() had been missed in the documentation for the
method - it is expected that the method will update the MAC to the
settings, rather than completely reprogram the MAC on each call.
Update the documentation for this method for this detail.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

This pointer is RCU protected, so proper primitives should be used.
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When using genphy_c45_read_abilities() as get_features callback we
also have to set the autoneg capability in phydev->supported.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.

The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.

However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull KVM fixes from Paolo Bonzini:
 "Bug fixes"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: MMU: record maximum physical address width in kvm_mmu_extended_role
  kvm: x86: Return LA57 feature based on hardware capability
  x86/kvm/mmu: fix switch between root and guest MMUs
  s390: vsie: Use effective CRYCBD.31 to check CRYCBD validity

Pull networking fixes from David Miller:
 "Hopefully the last pull request for this release. Fingers crossed:

   1) Only refcount ESP stats on full sockets, from Martin Willi.

   2) Missing barriers in AF_UNIX, from Al Viro.

   3) RCU protection fixes in ipv6 route code, from Paolo Abeni.

   4) Avoid false positives in untrusted GSO validation, from Willem de
      Bruijn.

   5) Forwarded mesh packets in mac80211 need more tailroom allocated,
      from Felix Fietkau.

   6) Use operstate consistently for linkup in team driver, from George
      Wilkie.

   7) ThunderX bug fixes from Vadim Lomovtsev. Mostly races between VF
      and PF code paths.

   8) Purge ipv6 exceptions during netdevice removal, from Paolo Abeni.

   9) nfp eBPF code gen fixes from Jiong Wang.

  10) bnxt_en firmware timeout fix from Michael Chan.

  11) Use after free in udp/udpv6 error handlers, from Paolo Abeni.

  12) Fix a race in x25_bind triggerable by syzbot, from Eric Dumazet"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
  net: phy: realtek: Dummy IRQ calls for RTL8366RB
  tcp: repaired skbs must init their tso_segs
  net/x25: fix a race in x25_bind()
  net: dsa: Remove documentation for port_fdb_prepare
  Revert "bridge: do not add port to router list when receives query with source 0.0.0.0"
  selftests: fib_tests: sleep after changing carrier. again.
  net: set static variable an initial value in atl2_probe()
  net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G
  bpf, doc: add bpf list as secondary entry to maintainers file
  udp: fix possible user after free in error handler
  udpv6: fix possible user after free in error handler
  fou6: fix proto error handler argument type
  udpv6: add the required annotation to mib type
  mdio_bus: Fix use-after-free on device_register fails
  net: Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255
  bnxt_en: Wait longer for the firmware message response to complete.
  bnxt_en: Fix typo in firmware message timeout logic.
  nfp: bpf: fix ALU32 high bits clearance bug
  nfp: bpf: fix code-gen bug on BPF_ALU | BPF_XOR | BPF_K
  Documentation: networking: switchdev: Update port parent ID section
  ...

Also, extend neigh_state_str to include neigh dummy states
noarp and permanent

Fixes: 9c03b282 ("trace: events: add a few neigh tracepoints")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes a regression introduced by
commit 0d2e778e
"net: phy: replace PHY_HAS_INTERRUPT with a check for
config_intr and ack_interrupt".

This assumes that a PHY cannot trigger interrupt unless
it has .config_intr() or .ack_interrupt() implemented.
A later patch makes the code assume both need to be
implemented for interrupts to be present.

But this PHY (which is inside a DSA) will happily
fire interrupts without either callback.

Implement dummy callbacks for .config_intr() and
.ack_interrupt() in the phy header to fix this.

Tested on the RTL8366RB on D-Link DIR-685.

Fixes: 0d2e778e ("net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot reported a WARN_ON(!tcp_skb_pcount(skb))
in tcp_send_loss_probe() [1]

This was caused by TCP_REPAIR sent skbs that inadvertenly
were missing a call to tcp_init_tso_segs()

[1]
WARNING: CPU: 1 PID: 0 at net/ipv4/tcp_output.c:2534 tcp_send_loss_probe+0x771/0x8a0 net/ipv4/tcp_output.c:2534
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.0.0-rc7+ #77
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 <IRQ>
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x172/0x1f0 lib/dump_stack.c:113
 panic+0x2cb/0x65c kernel/panic.c:214
 __warn.cold+0x20/0x45 kernel/panic.c:571
 report_bug+0x263/0x2b0 lib/bug.c:186
 fixup_bug arch/x86/kernel/traps.c:178 [inline]
 fixup_bug arch/x86/kernel/traps.c:173 [inline]
 do_error_trap+0x11b/0x200 arch/x86/kernel/traps.c:271
 do_invalid_op+0x37/0x50 arch/x86/kernel/traps.c:290
 invalid_op+0x14/0x20 arch/x86/entry/entry_64.S:973
RIP: 0010:tcp_send_loss_probe+0x771/0x8a0 net/ipv4/tcp_output.c:2534
Code: 88 fc ff ff 4c 89 ef e8 ed 75 c8 fb e9 c8 fc ff ff e8 43 76 c8 fb e9 63 fd ff ff e8 d9 75 c8 fb e9 94 f9 ff ff e8 bf 03 91 fb <0f> 0b e9 7d fa ff ff e8 b3 03 91 fb 0f b6 1d 37 43 7a 03 31 ff 89
RSP: 0018:ffff8880ae907c60 EFLAGS: 00010206
RAX: ffff8880a989c340 RBX: 0000000000000000 RCX: ffffffff85dedbdb
RDX: 0000000000000100 RSI: ffffffff85dee0b1 RDI: 0000000000000005
RBP: ffff8880ae907c90 R08: ffff8880a989c340 R09: ffffed10147d1ae1
R10: ffffed10147d1ae0 R11: ffff8880a3e8d703 R12: ffff888091b90040
R13: ffff8880a3e8d540 R14: 0000000000008000 R15: ffff888091b90860
 tcp_write_timer_handler+0x5c0/0x8a0 net/ipv4/tcp_timer.c:583
 tcp_write_timer+0x10e/0x1d0 net/ipv4/tcp_timer.c:607
 call_timer_fn+0x190/0x720 kernel/time/timer.c:1325
 expire_timers kernel/time/timer.c:1362 [inline]
 __run_timers kernel/time/timer.c:1681 [inline]
 __run_timers kernel/time/timer.c:1649 [inline]
 run_timer_softirq+0x652/0x1700 kernel/time/timer.c:1694
 __do_softirq+0x266/0x95a kernel/softirq.c:292
 invoke_softirq kernel/softirq.c:373 [inline]
 irq_exit+0x180/0x1d0 kernel/softirq.c:413
 exiting_irq arch/x86/include/asm/apic.h:536 [inline]
 smp_apic_timer_interrupt+0x14a/0x570 arch/x86/kernel/apic/apic.c:1062
 apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:807
 </IRQ>
RIP: 0010:native_safe_halt+0x2/0x10 arch/x86/include/asm/irqflags.h:58
Code: ff ff ff 48 89 c7 48 89 45 d8 e8 59 0c a1 fa 48 8b 45 d8 e9 ce fe ff ff 48 89 df e8 48 0c a1 fa eb 82 90 90 90 90 90 90 fb f4 <c3> 0f 1f 00 66 2e 0f 1f 84 00 00 00 00 00 f4 c3 90 90 90 90 90 90
RSP: 0018:ffff8880a98afd78 EFLAGS: 00000286 ORIG_RAX: ffffffffffffff13
RAX: 1ffffffff1125061 RBX: ffff8880a989c340 RCX: 0000000000000000
RDX: dffffc0000000000 RSI: 0000000000000001 RDI: ffff8880a989cbbc
RBP: ffff8880a98afda8 R08: ffff8880a989c340 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000001
R13: ffffffff889282f8 R14: 0000000000000001 R15: 0000000000000000
 arch_cpu_idle+0x10/0x20 arch/x86/kernel/process.c:555
 default_idle_call+0x36/0x90 kernel/sched/idle.c:93
 cpuidle_idle_call kernel/sched/idle.c:153 [inline]
 do_idle+0x386/0x570 kernel/sched/idle.c:262
 cpu_startup_entry+0x1b/0x20 kernel/sched/idle.c:353
 start_secondary+0x404/0x5c0 arch/x86/kernel/smpboot.c:271
 secondary_startup_64+0xa4/0xb0 arch/x86/kernel/head_64.S:243
Kernel Offset: disabled
Rebooting in 86400 seconds..

Fixes: 79861919 ("tcp: fix TCP_REPAIR xmit queue setup")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Andrey Vagin <avagin@openvz.org>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot was able to trigger another soft lockup [1]

I first thought it was the O(N^2) issue I mentioned in my
prior fix (f657d22ee1f "net/x25: do not hold the cpu
too long in x25_new_lci()"), but I eventually found
that x25_bind() was not checking SOCK_ZAPPED state under
socket lock protection.

This means that multiple threads can end up calling
x25_insert_socket() for the same socket, and corrupt x25_list

[1]
watchdog: BUG: soft lockup - CPU#0 stuck for 123s! [syz-executor.2:10492]
Modules linked in:
irq event stamp: 27515
hardirqs last  enabled at (27514): [<ffffffff81006673>] trace_hardirqs_on_thunk+0x1a/0x1c
hardirqs last disabled at (27515): [<ffffffff8100668f>] trace_hardirqs_off_thunk+0x1a/0x1c
softirqs last  enabled at (32): [<ffffffff8632ee73>] x25_get_neigh+0xa3/0xd0 net/x25/x25_link.c:336
softirqs last disabled at (34): [<ffffffff86324bc3>] x25_find_socket+0x23/0x140 net/x25/af_x25.c:341
CPU: 0 PID: 10492 Comm: syz-executor.2 Not tainted 5.0.0-rc7+ #88
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:__sanitizer_cov_trace_pc+0x4/0x50 kernel/kcov.c:97
Code: f4 ff ff ff e8 11 9f ea ff 48 c7 05 12 fb e5 08 00 00 00 00 e9 c8 e9 ff ff 90 90 90 90 90 90 90 90 90 90 90 90 90 55 48 89 e5 <48> 8b 75 08 65 48 8b 04 25 40 ee 01 00 65 8b 15 38 0c 92 7e 81 e2
RSP: 0018:ffff88806e94fc48 EFLAGS: 00000286 ORIG_RAX: ffffffffffffff13
RAX: 1ffff1100d84dac5 RBX: 0000000000000001 RCX: ffffc90006197000
RDX: 0000000000040000 RSI: ffffffff86324bf3 RDI: ffff88806c26d628
RBP: ffff88806e94fc48 R08: ffff88806c1c6500 R09: fffffbfff1282561
R10: fffffbfff1282560 R11: ffffffff89412b03 R12: ffff88806c26d628
R13: ffff888090455200 R14: dffffc0000000000 R15: 0000000000000000
FS:  00007f3a107e4700(0000) GS:ffff8880ae800000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f3a107e3db8 CR3: 00000000a5544000 CR4: 00000000001406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 __x25_find_socket net/x25/af_x25.c:327 [inline]
 x25_find_socket+0x7d/0x140 net/x25/af_x25.c:342
 x25_new_lci net/x25/af_x25.c:355 [inline]
 x25_connect+0x380/0xde0 net/x25/af_x25.c:784
 __sys_connect+0x266/0x330 net/socket.c:1662
 __do_sys_connect net/socket.c:1673 [inline]
 __se_sys_connect net/socket.c:1670 [inline]
 __x64_sys_connect+0x73/0xb0 net/socket.c:1670
 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x457e29
Code: ad b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f3a107e3c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002a
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000457e29
RDX: 0000000000000012 RSI: 0000000020000200 RDI: 0000000000000005
RBP: 000000000073c040 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f3a107e46d4
R13: 00000000004be362 R14: 00000000004ceb98 R15: 00000000ffffffff
Sending NMI from CPU 0 to CPUs 1:
NMI backtrace for cpu 1
CPU: 1 PID: 10493 Comm: syz-executor.3 Not tainted 5.0.0-rc7+ #88
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:__read_once_size include/linux/compiler.h:193 [inline]
RIP: 0010:queued_write_lock_slowpath+0x143/0x290 kernel/locking/qrwlock.c:86
Code: 4c 8d 2c 01 41 83 c7 03 41 0f b6 45 00 41 38 c7 7c 08 84 c0 0f 85 0c 01 00 00 8b 03 3d 00 01 00 00 74 1a f3 90 41 0f b6 55 00 <41> 38 d7 7c eb 84 d2 74 e7 48 89 df e8 cc aa 4e 00 eb dd be 04 00
RSP: 0018:ffff888085c47bd8 EFLAGS: 00000206
RAX: 0000000000000300 RBX: ffffffff89412b00 RCX: 1ffffffff1282560
RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffffffff89412b00
RBP: ffff888085c47c70 R08: 1ffffffff1282560 R09: fffffbfff1282561
R10: fffffbfff1282560 R11: ffffffff89412b03 R12: 00000000000000ff
R13: fffffbfff1282560 R14: 1ffff11010b88f7d R15: 0000000000000003
FS:  00007fdd04086700(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fdd04064db8 CR3: 0000000090be0000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 queued_write_lock include/asm-generic/qrwlock.h:104 [inline]
 do_raw_write_lock+0x1d6/0x290 kernel/locking/spinlock_debug.c:203
 __raw_write_lock_bh include/linux/rwlock_api_smp.h:204 [inline]
 _raw_write_lock_bh+0x3b/0x50 kernel/locking/spinlock.c:312
 x25_insert_socket+0x21/0xe0 net/x25/af_x25.c:267
 x25_bind+0x273/0x340 net/x25/af_x25.c:703
 __sys_bind+0x23f/0x290 net/socket.c:1481
 __do_sys_bind net/socket.c:1492 [inline]
 __se_sys_bind net/socket.c:1490 [inline]
 __x64_sys_bind+0x73/0xb0 net/socket.c:1490
 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x457e29

Fixes: 90c27297 ("X.25 remove bkl in bind")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: andrew hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This callback was removed some time ago, also remove the documentation.

Fixes: 1b6dd556 ("net: dsa: Remove prepare phase for FDB")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 5a2de63f ("bridge: do not add port to router list
when receives query with source 0.0.0.0") and commit 0fe5119e ("net:
bridge: remove ipv6 zero address check in mcast queries")

The reason is RFC 4541 is not a standard but suggestive. Currently we
will elect 0.0.0.0 as Querier if there is no ip address configured on
bridge. If we do not add the port which recives query with source
0.0.0.0 to router list, the IGMP reports will not be about to forward
to Querier, IGMP data will also not be able to forward to dest.

As Nikolay suggested, revert this change first and add a boolopt api
to disable none-zero election in future if needed.
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Reported-by: Sebastian Gottschall <s.gottschall@newmedia-net.de>
Fixes: 5a2de63f ("bridge: do not add port to router list when receives query with source 0.0.0.0")
Fixes: 0fe5119e ("net: bridge: remove ipv6 zero address check in mcast queries")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Just like commit e2ba732a ("selftests: fib_tests: sleep after
changing carrier"), wait one second to allow linkwatch to propagate the
carrier change to the stack.

There are two sets of carrier tests. The first slept after the carrier
was set to off, and when the second set ran, it was likely that the
linkwatch would be able to run again without much delay, reducing the
likelihood of a race. However, if you run 'fib_tests.sh -t carrier' on a
loop, you will quickly notice the failures.

Sleeping on the second set of tests make the failures go away.

Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: aquantia: improve and extend driver

This series improves and extends the Aquantia PHY driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use new function genphy_c45_read_status(). 1000BaseT link partner
advertisement needs to be read from vendor registers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to genphy_read_status() for Clause 22 add a generic read_status
function for Clause 45.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Because 1000BaseT isn't covered by Clause 45, the 1000BaseT flags in
phydev->lp_advertising may have been set based on vendor registers
already. genphy_c45_read_lpa() would clear these flags as of today.
Therefore switch to mii_lpa_mod_linkmode_lpa_t.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make use of the generic c45 code, plus code specific to the Aquantia
phy for 1000BaseT negotiation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

AQCS109 belongs to a family of PHY's where certain members don't
support 5G or 10G. However for all members of the family the chip
reports 10G and 5G capability. Therefore remove the not supported
modes for AQCS109.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>