Some people wants to log only oops messages via netconsole,
(this is also why netoops was invented)
so add a module option for netconsole. This can be tuned
via /sys/module/netconsole/parameters/oops_only at run time
as well.

Cc: David Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sets the sysfs device_type to 'vlan' for udev. This makes it easier for
applications that query network information via udev to identify vlans
instead of using strrchr().
Signed-off-by: Doug Goldstein <cardoe@cardoe.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The shmobile SH7377 already was removed from source tree.
This remove SH7377 support for sh-irda.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The shmobile SH7367 already was removed from source tree.
This remove SH7367 support for sh-irda.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

6431cbc2(Create a mechanism for upward inetpeer propagation into routes)
introduces these codes, but this mechanism is never enabled since
rt6i_peer_genid always is zero whether it is not assigned or assigned by
rt6_peer_genid(). After 5943634f (ipv4: Maintain redirect and PMTU info
in struct rtable again), the ipv4 related codes of this mechanism has been
removed, I think we maybe able to remove them now.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Included changes:
- minimal fixes to the packet layout to avoid the __packed attribute when not
  needed
- new packet type called UNICAST_4ADDR: in this packet it is possible to find
  both source and destination node (in the classic UNICAST header only the
  destination field exists).
- a new feature: Distributed ARP Table (D.A.T.). It aims to reduce ARP lookups
  latency by means of a simil-DHT approach.

Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch replaces the BCM_CNIC define with a flag which can change at run-time
and which does not use the CONFIG_CNIC kconfig option.
For the PF/hypervisor driver cnic is always supported, however allocation of
cnic resources and configuration of the HW for offload mode is done only when
the cnic module registers bnx2x.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch updates the driver-FW HSI to support changes to the 'update' ramrod
(FW supports this change since 7.8.2). This ramrod is sent when the cnic module
registers bnx2x, to enable changing the nic_mode configuration in HW at
run-time.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The tx data offset of packet mmap tx ring used to be :
(TPACKET2_HDRLEN - sizeof(struct sockaddr_ll))

The problem is that, with SOCK_RAW socket, the payload (14 bytes after
the beginning of the user data) is misaligned.

This patch allows to let the user gives an offset for it's tx data if
he desires.

Set sock option PACKET_TX_HAS_OFF to 1, then specify in each frame of
your tx ring tp_net for SOCK_DGRAM, or tp_mac for SOCK_RAW.
Signed-off-by: Paul Chavent <paul.chavent@onera.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

move below calculate out of spin lock section
	diff = fep->cc.mult;
	diff *= ppb;
	diff = div_u64(diff, 1000000000ULL);

diff is local variable and not neccesary in spin lock
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove PPS.
Limit FEC_PTP option for i.MX chip only.
FEC_PTP default is on at mx6 platform.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert all printk's to netdev_ counterparts and fix up some
printed texts.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

No longer used after gpio phy interrupt support was
removed from at91_ether.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

for usage in at91_ether driver.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is used on one AT91RM9200 board where a bootloader stores
the Ethernet address in the wrong order.

Support this on macb so address setting functions can be shared
with the at91_ether driver.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The macb driver in u-boot uses the first register set while
the at91_ether driver in u-boot uses the second register set.

By checking all register set, like at91_ether does, this code
can be shared between the drivers.

This only changes behavior on macb if no vaild address
is found in the first register set.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's not used anywhere
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

roce interface is suppored only on Skyhawk-R.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The SEMAPHORE register was being accessed from the csr BAR space. This BAR
may not be available in some Skyhawk-R configurations. Instead, access this
register via the PCI config space (it's available there too).
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1) separate NIC and roce bar mapping code
2) parse sli_intf::if_type inside be_map_pci_bars() as if_type must be
   used only to identify bars.
3) Use pci_iomap/unmap() routines
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SKYHAWK_FAMILY will not identify all revisions of the chip.
Use device-id check (skyhawk_chip() macro) instead.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

adapter->generation was being incorrectly set as BE_GEN3 for Skyhawk-R.
Replace generation usage with XXX_chip() macros to identify the chip.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's not needed anymore.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4 currently uses a too high tx coalescing setting, deferring
TX completion interrupts by up to 128 us.

With the recent skb_orphan() removal in commit 8112ec3b,
performance of a single TCP flow is capped to ~4 Gbps, unless
we increase tcp_limit_output_bytes.

I suggest using 16 us instead of 128 us, allowing a finer control.

Performance of a single TCP flow is restored to previous levels,
while keeping TCP small queues fully enabled with default sysctl.

This patch is also a BQL prereq.
Reported-by: Vimalkumar <j.vimal@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The "early client detection mechanism" can be extended to find new clients by
means of unicast_4addr packets.

The unicast_4addr packet contains as well as the broadcast packet (which is
currently used in this mechanism) the address of the originating node and can
therefore be used to install new entries in the Global Translation Table
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>

Added additional counters for D.A.T.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

This patch adds a runtime switch that enables the user to turn the DAT feature
on or off at runtime
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

This patch makes it possible to decide whether to include DAT within the
batman-adv binary or not.
It is extremely useful when the user wants to reduce the size of the resulting
module by cutting off any not needed feature.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

In case of an ARP message going in or out the soft_iface, it is intercepted and
a special action is performed. In particular the DHT helper functions previously
implemented are used to store all the ARP entries belonging to the network in
order to provide a fast and unicast lookup instead of the classic broadcast
flooding mechanism.
Each node stores the entries it is responsible for (following the DHT rules) in
its soft_iface ARP table. This makes it possible to reuse the kernel data
structures and functions for ARP management.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

ARP messages are now parsed to make it possible to trigger special actions
depending on their types (snooping).
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

Since batman-adv cannot inter-operate with the host ARP table, this patch
introduces a batman-adv private storage for ARP entries exchanged within DAT.
This storage will represent the node local cache in the DAT protocol.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

Add all the relevant functions in order to manage a Distributed Hash Table over
the B.A.T.M.A.N.-adv network. It will later be used to store several ARP entries
and implement DAT (Distributed ARP Table)
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

A new log level has been added to concentrate messages regarding DAT: ARP
snooping, requests, response and DHT related messages.
The new log level is named BATADV_DBG_DAT
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

The current unicast packet type does not contain the orig source address. This
patches add a new unicast packet (called UNICAST_4ADDR) which provides two new
fields: the originator source address and the subtype (the type of the data
contained in the packet payload). The former is useful to identify the node
which injected the packet into the network and the latter is useful to avoid
creating new unicast packet types in the future: a macro defining a new subtype
will be enough.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

Headers which are already perfectly aligned and create a 4 byte boundary
non-ethernet header payload can have the __packed attribute removed. The
__packed attribute doesn't change the appeareance of the packet for these
headers because no extra padding is necessary to align the data members. The
compiler will also create slightly faster code for loads of multi-byte members.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>