- 22 Jan, 2018 5 commits
-
-
Chris Wilson authored
On gen9+, after an idle period the HW will disable the entire power well to conserve power (by preventing current leakage). It takes around a 100 microseconds to bring the power well back online afterwards. With the current hysteresis value of 25us (really 25 * 1280ns), we do not have sufficient time to respond to an interrupt and schedule the next execution before the HW powers itself down. (At present, we prevent this by grabbing the forcewake for prolonged periods of time, but that overkill fixed in the next patch.) The minimum we want to set the power gating hysteresis to is the length of time it takes us to service the GPU, which across a broad spectrum of machines is about 250us. (Note this also brings guc latency into the same ballpark as execlists.) v2: Include some notes on where I plucked the numbers from. Testcase: igt/gem_exec_nop/sequential Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com> Cc: Michel Thierry <michel.thierry@intel.com> Cc: Michal Winiarski <michal.winiarski@intel.com> Reviewed-by:
Sagar Arun Kamble <sagar.a.kamble@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180122135541.32222-1-chris@chris-wilson.co.uk
-
Tvrtko Ursulin authored
We fail engine initialization if the scratch VMA cannot be created so there is no point in error handle it later. If the initialization ordering gets messed up, we can explode during development just as well. Signed-off-by:
Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by:
Michel Thierry <michel.thierry@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180119100005.9072-2-tvrtko.ursulin@linux.intel.com
-
Tvrtko Ursulin authored
Render engine constructor helpers must only be called from the render engine constructors, but there is no need to burden the production binaries with warnings which can only be triggered during development. Signed-off-by:
-
Manasi Navare authored
In case of eDP because the panel has a fixed mode, the link rate and lane count at which it is trained corresponds to the link BW required to support the native resolution of the panel. In case of panles with lower resolutions where fewer lanes are hooked up internally, that number is reflected in the MAX_LANE_COUNT DPCD register of the panel. So it is pointless to fallback to lower link rate/lane count in case of link training failure on eDP connector since the lower link BW will not support the native resolution of the panel and we cannot prune the preferred mode on the eDP connector. In case of Link training failure on the eDP panel, something is wrong in the HW internally and hence driver errors out with a loud and clear DRM_ERROR message. v2: * Fix the DEBUG_ERROR and add {} in else (Ville Syrjala) Cc: Clinton Taylor <clinton.a.taylor@intel.com> Cc: Jim Bride <jim.bride@linux.intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Dave Airlie <airlied@redhat.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:Manasi Navare <manasi.d.navare@intel.com> Reviewed-by:
Ville Syrjala <ville.syrjala@linux.intel.com> Reference: https://bugs.freedesktop.org/show_bug.cgi?id=103369Signed-off-by:
Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/1507835618-23051-1-git-send-email-manasi.d.navare@intel.com
-
Chris Wilson authored
As we attempt to allocate pages for use in a new WC stash, direct reclaim may run underneath us and fill up the WC stash. We have to be careful then not to overflow the pvec. Fixes: 66df1014 ("drm/i915: Keep a small stash of preallocated WC pages") Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103109Signed-off-by:
Matthew Auld <matthew.auld@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180121173143.17090-1-chris@chris-wilson.co.uk
-
- 20 Jan, 2018 1 commit
-
-
Dhinakaran Pandiyan authored
Avoids some typo pitfalls. Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by:
Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Reviewed-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by:
-
- 19 Jan, 2018 22 commits
-
-
Chris Wilson authored
If we fail to allocate a new request, make sure we recover the pages that are in the process of being freed by inserting an RCU barrier. v2: Comment before the shrink and barrier in the error path. Signed-off-by:
-
Michal Wajdeczko authored
It looks that GuC log functionality is not fully functional yet and causes issues when enabled by auto(-1) modparam on debug builds. For example, but not limited to: [ 30.062893] ====================================================== [ 30.062894] WARNING: possible circular locking dependency detected [ 30.062895] 4.15.0-rc8-CI-CI_DRM_3648+ #1 Tainted: G U [ 30.062896] ------------------------------------------------------ [ 30.062897] debugfs_test/1268 is trying to acquire lock: [ 30.062898] (&dev->struct_mutex){+.+.}, at: [<00000000e4213449>] i915_mutex_lock_interruptible+0x47/0x130 [i915] [ 30.062921] but task is already holding lock: [ 30.062921] (&mm->mmap_sem){++++}, at: [<00000000dd7adc93>] __do_page_fault+0x106/0x560 [ 30.062924] which lock already depends on the new lock. References: 0ed87953 ("drm/i915/guc: Redefine guc_log_level modparam values") Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104693 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104694 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104695Signed-off-by:Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Jani Saarinen <jani.saarinen@intel.com> Cc: Tomi Sarvela <tomi.p.sarvela@intel.com> Cc: Marta Lofstedt <marta.lofstedt@intel.com> Cc: Michal Winiarski <michal.winiarski@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180119124926.29844-1-michal.wajdeczko@intel.comReviewed-by:
Michal Winiarski <michal.winiarski@intel.com> Signed-off-by:
-
Tvrtko Ursulin authored
Gen11 removes the Resource Streamer, which frees up a big chunk of the context image. BSpec indicates 12544 DWORDs (13 pages), plus one page for PPHWSP. Please notice that, when looking at the BSpec context image table, the right filter has to be applied as some rows are excluded for specific GENs. Also, some rows apply per-subslice (for the calculation above, we have supposed I915_MAX_SUBSLICES = 8). v2: Rebase. v3: Use the right size as per the BSpec. v4: - Rebased on top of the default context size (Rodrigo) - Clarify in the commit message where the subslice calculation comes from. v5: s/12538/12544/ (Daniele) BSpec: 18907 Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Acked-by: Ben Widawsky <benjamin.widawsky@intel.com> (older version) Reviewed-by:Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Signed-off-by:
Oscar Mateo <oscar.mateo@intel.com> Signed-off-by:
Paulo Zanoni <paulo.r.zanoni@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/1515711307-28979-2-git-send-email-oscar.mateo@intel.com
-
Oscar Mateo authored
Instead of returning whatever size the latest GEN used. This is because context sizes for new GENs can go up or down, but the only safe thing to do for missing cases is to use the largest known one, whatever that is. Suggested-by:
-
Tvrtko Ursulin authored
MMIO addresses and register definition for the new interrupt registers in Gen11. v2: Removed spelt out VCS and VECS bit definitions. (Daniel Vetter) v3: Adjust VCS and VECS. (Daniele Ceraolo Spurio) v4: Bikeshedding (Paulo). Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Reviewed-by:
-
Anusha Srivatsa authored
Add the PCI ID for the ICL PCH - ICP. v2: rebased. v3: rebased. v4: fix ICP name. v5: fix the ID mask (Fei Li). v6 (from Paulo): bikesheds. Cc: Li, Fei <fei.li@intel.com> Reviewed-by:
Anusha Srivatsa <anusha.srivatsa@intel.com> Signed-off-by:
-
Anusha Srivatsa authored
In ICP, there are three TC ports and 3 DDI ports. v2: - Correct Pin mapping. v3: - Update pin mapping into per platform implementation rather than previous approach of port wise mapping. v4: - Update GMBUS_NUM_PINS (Paulo) v5: - rebase. v6: - Update function name, GMBUS_PIN_NUM (Paulo) v7 (from Paulo): - Make it apply. v8 (from Paulo): - Maintain consistent if ladder ordering. Suggested by: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Reviewed-by:
-
Anusha Srivatsa authored
ICP has two backlight controllers - similar to previous platforms like BXT -, but we only use one controller for now, so we can just reuse the CNP code. v2: Remove the usage of ICP_SECOND_PPS_BACKLIGHT register.(Jani) Reuse CNP code since it is very similar.(Ville) v3 (from Paulo): Rebase. v4 (from Paulo): adjust commit message (James) and comment (Rodrigo). Cc: Jani Nikula <jani.nikula@intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Acked-by:
James Ausmus <james.ausmus@intel.com> Reviewed-by:
-
Anusha Srivatsa authored
ICP, like BXT, has has two panel power sequencers. v2: Simplify the code. Remove unwanted register definitions. Make code as close to BXT style as possible. (Ville) Also, remove the use of ICP_SECOND_PPS_BACKLIGHT for now. Moving forward, if we are sure we need to set this register, we can access it. v3: Use INTEL_GEN(dev_priv), make code more readeable. (Ville) v4 (from Paulo): - Coding style fixes. - Add a missing HAS_PCH_CNP -> gen10+ check. - Rebase. v5: Use per platform checks rather than INTEL_GEN(). v4 of this patch breaks on CoffeeLake, since CFL uses CNP and per platform check makes sense in that case. v6 (from Paulo): - v5 was a patch on top of v4, not a new version. Now v6 is correctly a new version of the original patch. Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Reviewed-by: -
Anusha Srivatsa authored
Add register definitions for setting the rawclock. Set the numerator,denominator and divider values. v2: Simplify the commit message. Simplify the math. Add register bits for numerator. (Paulo) v3 (from Paulo): coding style bikesheds. Reviewed-by:
-
Anusha Srivatsa authored
Add the enum additions to ICP PCH. v2 (from Paulo): don't set any platforms to it yet since ICP support is incomplete. v3 (from Rodrigo): Fix ICP name. Reviewed-by:
-
Rodrigo Vivi authored
Icelake is an Intel
® Processor containing an Intel® Graphics Controller. This is just an initial Icelake definition. PCI IDs, Icelake support and new features coming in following patches. v2: Add .ddb_size and .has_guc (Michal Wajdeczko). v3: Add the ICL_FEATURES macro (Kelvin Gardiner). v4 (from Paulo): Add missing __initconst (Paulo) and say "graphics controller" instead of something that looks like an official marketing name but isn't (Chris). Reviewed-by: -
Rodrigo Vivi authored
Some Cannonlake SKUs will come with a full split between port A and port E. This will be called port F although it is not a 6th port, but only a split. Note this patch alone is not sufficient for port F enabling, it's just the first step. v2: Fix size of dvo_ports found by Ander. v3: Adding missing cases from intel_bios.c for Port_F v4: Adding other missing cases and fix the commit message. v5: Rebase on top of display headers rework. v6 (from Paulo): improve commit message, bikeshed bit definitions. Cc: Lucas De Marchi <lucas.demarchi@intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Acked-by:
-
Mika Kahola authored
We may have fused or unused pipes in our system. Let's check that the pipe in question is within limits of accessible pipes. In case, that we are not able to access the pipe, we return early with a warning. v2: Rephrasing of the commit message (Jani) Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103206Reported-by:
Thomas Gleixner <tglx@linutronix.de> Tested-by:
Jaswinder Singh Rajput <jaswinder@perfectintelligent.com> Suggested-by:
Jani Nikula <jani.nikula@intel.com> Reviewed-by:
Mika Kahola <mika.kahola@intel.com> Signed-off-by:
-
Ville Syrjälä authored
SKL+ "sprites" no longer have 16KB max stride limit that earlier platforms had. Bump up the limit to 32KB. Cc: Ben Widawsky <ben@bwidawsk.net> Cc: Jason Ekstrand <jason@jlekstrand.net> Cc: Daniel Stone <daniels@collabora.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch>
-
Ville Syrjälä authored
Allow sprites to scan out compressed framebuffers. Since different platforms have a different set of planes that support CCS let's add a small helper to determine whether a specific plane supports CCS or not. Currently that information is spread around in many places, and not all the pieces of code even agree with each other. In addition to allowing sprites to scan out compressed fbs, the other fix here is that we stop rejecting them on pipe C on CNL. Cc: Ben Widawsky <ben@bwidawsk.net> Cc: Jason Ekstrand <jason@jlekstrand.net> Cc: Daniel Stone <daniels@collabora.com> Signed-off-by:
-
Ville Syrjälä authored
Split the g4x and snb cases into separate functions to match how we deal with all other platforms. Also sort the switch cases to match the format lists we've declared earlier, to ease comparisons. Cc: Ben Widawsky <ben@bwidawsk.net> Cc: Jason Ekstrand <jason@jlekstrand.net> Cc: Daniel Stone <daniels@collabora.com> Signed-off-by:
-
Ville Syrjälä authored
Y/Yf were dropped out from the SKL+ sprite modifier list on account of some watermark issues Daniel Stone was having. My subsequent testing seemed to indicate that things work better now, so add the modifiers back in. v2: Update the commit message with a better explanation Cc: Ben Widawsky <ben@bwidawsk.net> Cc: Jason Ekstrand <jason@jlekstrand.net> Cc: Daniel Stone <daniels@collabora.com> Signed-off-by:
-
Ville Syrjälä authored
The unreachable() is very much unreachable and the compiler knows that, so there's no point in having it. Cc: Ben Widawsky <ben@bwidawsk.net> Cc: Jason Ekstrand <jason@jlekstrand.net> Cc: Daniel Stone <daniels@collabora.com> Signed-off-by:
-
Abdiel Janulgue authored
4K modes testing by using dummy EDID data has never been working properly on boxes with DP++ (dual-mode) adaptors. The reason for this is that those modes got pruned during hdmi mode validation. intel_hdmi_mode_valid returns CLOCK_HIGH because the pixel clock reported by the 4k mode is higher than dual port TMDS clock limit. However 4k injection does work properly on machines that don't have DP++ adapters because the mode is never validated against the DP++ TMDS clock limit. v2: Don't detect the DP++ limits when we're testing using overridden EDIDs. Make sure to check for the override condition after respecting the value of drm_dp_dual_mode_detect (Jani Nikula). Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101649 Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:Abdiel Janulgue <abdiel.janulgue@linux.intel.com> Signed-off-by:
-
Jani Nikula authored
drm_edid_to_eld() sets ELD connector type since commit 1d1c3665 ("drm/edid: set ELD connector type in drm_edid_to_eld()"). Remove the redundant update. (Commit c945b8c1 ("drm/edid: build ELD in drm_add_edid_modes()") and commit d471ed04 ("drm/drivers: drop redundant drm_edid_to_eld() calls") are also related.) v2: Rebase, update commit message with commit references. Reviewed-by:
Alex Deucher <alexander.deucher@amd.com> Acked-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
-
Jani Nikula authored
No more sing-a-ling. Reported-by:
Adam Jackson <ajax@redhat.com> You're-my-ding-a-ling-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by:
David Weinehall <david.weinehall@linux.intel.com> Signed-off-by:
-
- 18 Jan, 2018 8 commits
-
-
Jani Nikula authored
Update VBT defs to reflect revision 216. While at it, default the expected child device struct size to sizeof the size rather than a hardcoded value. v2: Fix bit order (David) Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by:
-
Lucas De Marchi authored
Display WA #1178 is meant to fix Aux channel voltage swing too low with some type C dongles. Although it is for type C, HW engineers reported that it can be applied to all external ports even if they are not going to type C. For CNL we apply the workaround every time Aux B, C and D are powering up since they will lose the configuration when powered down. v2: Use common tag for WA Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Arthur J Runyan <arthur.j.runyan@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by:
-
Michel Thierry authored
Instead of using local string names that we will have to keep maintaining, use the engine->name directly. v2: Better invalid engine_id handling, capture_bo will not be able know the engine_id and end up with -1 (Michal). Suggested-by:
-
Michal Wajdeczko authored
Today we have format mismatch between read/write operations of i915_guc_log_control entry. For read we return (0, 1..4) that represents disable/verbosity levels, but for write we force user to follow internal structure format (0,1,9,11,13). Let's hide internals from the user and accept same values as we support for read and related guc_log_level modparam. Signed-off-by:
-
Michal Wajdeczko authored
We used value -1 to indicate "disabled" and values 0..3 to indicate "enabled", but most of our other modparams are using -1 for "auto" mode and 0 for "disable". For consistency let's change our log level values to: -1: auto (depends on platform and Kconfig.debug settings) 0: disabled 1: enabled (severity level 0 = min) 2: enabled (severity level 1) 3: enabled (severity level 2) 4: enabled (severity level 3 = max) v2: fix commit message (Sagar) display sanitized modparam value (Sagar) unify sanitize messages (Sagar/Michal) Signed-off-by: -
Chris Wilson authored
Watching a light workload on Baytrail (running glxgears and a 1080p decode), instead of the system remaining at low frequency, the glxgears would regularly trigger waitboosting after which it would have to spend a few seconds throttling back down. In this case, the waitboosting is counter productive as the minimal wait for glxgears doesn't prevent it from functioning correctly and delivering frames on time. In this case, glxgears happens to almost always be waiting on the current request, which we already expect to complete quickly (see i915_spin_request) and so avoiding the waitboost on the active request and spinning instead provides the best latency without overcommitting to upclocking. However, if the system falls behind we still force the waitboost. Similarly, we will also trigger upclocking if we detect the system is not delivering frames on time - again using a mechanism that tries to detect a miss and not preemptively upclock. v2: Also skip boosting for after missed vblank if the desired request is already active. Signed-off-by:
Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180118131609.16574-1-chris@chris-wilson.co.uk
-
Imre Deak authored
The CDCLK bypass frequency can vary on upcoming platforms, so prepare for that now by tracking its value in the CDCLK state. Currently on BDW+ the bypass frequency is always the reference clock and I didn't bother with earlier platforms since it's not all that clear what's the bypass clock on those. I also didn't bother adding support for changing this frequency, since atm I don't see any need for it. Suggested-by:
-
Chris Wilson authored
Since commit 4e773c3a ("drm/i915: Wire up shrinkctl->nr_scanned"), we track the number of objects we scan and do not wish to exceed that as it will overly penalise our own slabs under mempressure. Given that we now know the target number of objects to scan, use that as our guide for deciding to shrink as opposed to the number of objects we manage to shrink (which doesn't correspond to the numbers we report to shrinkctl). Fixes: 4e773c3a ("drm/i915: Wire up shrinkctl->nr_scanned") Signed-off-by:
-
- 17 Jan, 2018 3 commits
-
-
Arnd Bergmann authored
struct timeval is deprecated because it cannot represent times past 2038. In this driver, the only use of this structure is to capture debug information. This is easily changed to ktime_t, which we then format as needed when printing it later. Reviewed-by:
Arnd Bergmann <arnd@arndb.de> Link: https://patchwork.freedesktop.org/patch/msgid/20180117154916.219273-1-arnd@arndb.deSigned-off-by:
-
Chris Wilson authored
When testing that the timeout fired, we need to be sure we have waited just long enough for the timeout to have occurred and for the softirq (on another cpu) to have completed. Sleeping for an arbitrary amount is prone to error, so wait for the timeout instead and complain if it was too late. v2: Use wait_event_timeout to provide an upper bound v3: Fix inverted check for wait_event_timeout timing out v4: Restore the check that the fences aren't signalled too early, by inspecting them before the expected timeout. References: https://bugs.freedesktop.org/show_bug.cgi?id=104670Signed-off-by:
-
Maarten Lankhorst authored
It's perfectly legal to create a fb with stride < 512, and one of the kms_plane_scaling subtests creates a very small fb. Downgrade the WARN_ON to a simple check check, and because this function is potentially called on every atomic update/pageflip, downgrade the other WARN_ON to a WARN_ON_ONCE, and do the right thing here. Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by:
Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180116155331.75175-1-maarten.lankhorst@linux.intel.comReviewed-by:
-
- 16 Jan, 2018 1 commit
-
-
Maarten Lankhorst authored
intel_power_domains_init_hw() calls set_init_power, but when using runtime power management this call is skipped. This prevents hw readout from taking place. Signed-off-by:
-
