- 16 Aug, 2017 38 commits
-
-
Luis R. Rodriguez authored
commit e44565f6 upstream. The firmware cache mechanism serves two purposes, the secondary purpose is not well documented nor understood. This fixes a regression with the secondary purpose of the firmware cache mechanism: batched requests on successful lookups. Without this fix *any* time a batched request is triggered, secondary requests for which the batched request mechanism was designed for will seem to last forver and seem to never return. This issue is present for all kernel builds possible, and a hard reset is required. The firmware cache is used for: 1) Addressing races with file lookups during the suspend/resume cycle by keeping firmware in memory during the suspend/resume cycle 2) Batched requests for the same file rely only on work from the first file lookup, which keeps the firmware in memory until the last release_firmware() is called Batched requests *only* take effect if secondary requests come in prior to the first user calling release_firmware(). The devres name used for the internal firmware cache is used as a hint other pending requests are ongoing, the firmware buffer data is kept in memory until the last user of the buffer calls release_firmware(), therefore serializing requests and delaying the release until all requests are done. Batched requests wait for a wakup or signal so we can rely on the first file fetch to write to the pending secondary requests. Commit 5b029624 ("firmware: do not use fw_lock for fw_state protection") ported the firmware API to use swait, and in doing so failed to convert complete_all() to swake_up_all() -- it used swake_up(), loosing the ability for *some* batched requests to take effect. We *could* fix this by just using swake_up_all() *but* swait is now known to be very special use case, so its best to just move away from it. So we just go back to using completions as before commit 5b029624 ("firmware: do not use fw_lock for fw_state protection") given this was using complete_all(). Without this fix it has been reported plugging in two Intel 6260 Wifi cards on a system will end up enumerating the two devices only 50% of the time [0]. The ported swake_up() should have actually handled the case with two devices, however, *if more than two cards are used* the swake_up() would not have sufficed. This change is only part of the required fixes for batched requests. Another fix is provided in the next patch. This particular change should fix the cases where more than three requests with the same firmware name is used, otherwise batched requests will wait for MAX_SCHEDULE_TIMEOUT and just timeout eventually. Below is a summary of tests triggering batched requests on different kernel builds. Before this patch: ============================================================================ CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n CONFIG_FW_LOADER_USER_HELPER=y Most common Linux distribution setup. API-type no-firmware-found firmware-found ---------------------------------------------------------------------- request_firmware() FAIL FAIL request_firmware_direct() FAIL FAIL request_firmware_nowait(uevent=true) FAIL FAIL request_firmware_nowait(uevent=false) FAIL FAIL ============================================================================ CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n CONFIG_FW_LOADER_USER_HELPER=n Only possible if CONFIG_DELL_RBU=n and CONFIG_LEDS_LP55XX_COMMON=n, rare. API-type no-firmware-found firmware-found ---------------------------------------------------------------------- request_firmware() FAIL FAIL request_firmware_direct() FAIL FAIL request_firmware_nowait(uevent=true) FAIL FAIL request_firmware_nowait(uevent=false) FAIL FAIL ============================================================================ CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y CONFIG_FW_LOADER_USER_HELPER=y Google Android setup. API-type no-firmware-found firmware-found ---------------------------------------------------------------------- request_firmware() FAIL FAIL request_firmware_direct() FAIL FAIL request_firmware_nowait(uevent=true) FAIL FAIL request_firmware_nowait(uevent=false) FAIL FAIL ============================================================================ After this patch: ============================================================================ CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n CONFIG_FW_LOADER_USER_HELPER=y Most common Linux distribution setup. API-type no-firmware-found firmware-found ---------------------------------------------------------------------- request_firmware() FAIL OK request_firmware_direct() FAIL OK request_firmware_nowait(uevent=true) FAIL OK request_firmware_nowait(uevent=false) FAIL OK ============================================================================ CONFIG_FW_LOADER_USER_HELPER_FALLBACK=n CONFIG_FW_LOADER_USER_HELPER=n Only possible if CONFIG_DELL_RBU=n and CONFIG_LEDS_LP55XX_COMMON=n, rare. API-type no-firmware-found firmware-found ---------------------------------------------------------------------- request_firmware() FAIL OK request_firmware_direct() FAIL OK request_firmware_nowait(uevent=true) FAIL OK request_firmware_nowait(uevent=false) FAIL OK ============================================================================ CONFIG_FW_LOADER_USER_HELPER_FALLBACK=y CONFIG_FW_LOADER_USER_HELPER=y Google Android setup. API-type no-firmware-found firmware-found ---------------------------------------------------------------------- request_firmware() OK OK request_firmware_direct() FAIL OK request_firmware_nowait(uevent=true) OK OK request_firmware_nowait(uevent=false) OK OK ============================================================================ [0] https://bugzilla.kernel.org/show_bug.cgi?id=195477 Cc: Ming Lei <ming.lei@redhat.com> Fixes: 5b029624 ("firmware: do not use fw_lock for fw_state protection") Reported-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by:
Luis R. Rodriguez <mcgrof@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alan Swanson authored
commit 89f23d51 upstream. Similar to commit d595259f ("usb-storage: Add ignore-residue quirk for Initio INIC-3619") for INIC-3169 in unusual_devs.h but INIC-3069 already present in unusual_uas.h. Both in same controller IC family. Issue is that MakeMKV fails during key exchange with installed bluray drive with following error: 002004:0000 Error 'Scsi error - ILLEGAL REQUEST:COPY PROTECTION KEY EXCHANGE FAILURE - KEY NOT ESTABLISHED' occurred while issuing SCSI command AD010..080002400 to device 'SG:dev_11:0' Signed-off-by:
Alan Swanson <reiver@improbability.net> Acked-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
-
Ian Abbott authored
commit cef98864 upstream. Comedi's read and write file operation handlers (`comedi_read()` and `comedi_write()`) currently call `copy_to_user()` or `copy_from_user()` whilst in the `TASK_INTERRUPTIBLE` state, which falls foul of the `might_fault()` checks when enabled. Fix it by setting the current task state back to `TASK_RUNNING` a bit earlier before calling these functions. Reported-by:
Piotr Gregor <piotrgregor@rsyncme.org> Signed-off-by:
Ian Abbott <abbotti@mev.co.uk> Signed-off-by:
-
Hans de Goede authored
commit 631b010a upstream. Inheriting the ADC BIAS current settings from the BIOS instead of hardcoding then causes the AXP288 to disable charging (I think it mis-detects an overheated battery) on at least one model tablet. So lets go back to hard coding the values, this reverts commit fa2849e9 ("iio: adc: axp288: Drop bogus AXP288_ADC_TS_PIN_CTRL register modifications"), fixing charging not working on the model tablet in question. The exact cause is not fully understood, hence the revert to a known working state. Reported-by:
Umberto Ixxo <sfumato1977@gmail.com> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Akinobu Mita authored
commit a3507e48 upstream. The TSL2563 driver provides three iio channels, two of which are raw ADC channels (channel 0 and channel 1) in the device and the remaining one is calculated by the two. The ADC channel 0 only supports programmable interrupt with threshold settings and this driver supports the event but the generated event code does not contain the corresponding iio channel type. This is going to change userspace ABI. Hopefully fixing this to be what it should always have been won't break any userspace code. Cc: Jonathan Cameron <jic23@kernel.org> Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by:
-
Lorenzo Bianconi authored
commit add6e6ab upstream. Set multiread variable to false for LPS22HB pressure sensor since it is already enabled in CTRL_REG2. Previous configuration does not cause any issue in I2C communication since SUB Msb has no meaning whereas it breaks register address in SPI communication Fixes: e039e2f5 (iio:st_pressure:initial lps22hb sensor support) Signed-off-by:
Lorenzo Bianconi <lorenzo.bianconi@st.com> Signed-off-by:
-
Hans de Goede authored
commit e59e1898 upstream. After probe we would put the device in normal mode, after a runtime suspend-resume we would put it back in normal mode. But for a regular suspend-resume we would only put it back in normal mode if triggers or events have been requested. This is not consistent and breaks reading raw values after a suspend-resume. This commit changes the regular resume path to also unconditionally put the device back in normal mode, fixing reading of raw values not working after a regular suspend-resume cycle. Signed-off-by:
Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by:
-
Lorenzo Bianconi authored
commit a7b8829d upstream. Add SPI Serial Interface Mode (SIM) register information in st_sensor_settings look up table to support devices (like LSM303AGR accel sensor) that allow just SPI-3wire communication mode. SIM mode has to be configured before any other operation since it is not enabled by default and the driver is not able to read without that configuration Whilst a fairly substantial patch, the actual logic is simple and it is better to have the generic fix than a band aid. Fixes: ddc05fa2 (iio: st-accel: add support for lsm303agr accel) Signed-off-by:
-
Mykola Kostenok authored
commit 737cc2a5 upstream. This patch enables adc engine at initialization time and waits for the initial sequence completion before enabling adc channels. Without this code adc channels are not functional and shows zeros for all connected channels. Tested on mellanox msn platform. v1 -> v2: Pointed by Rick Altherr: - Wait init sequence code enabled by bool from OF match table. Signed-off-by:
Mykola Kostenok <c_mykolak@mellanox.com> Reviewed-by:
Rick Altherr <raltherr@google.com> Signed-off-by:
-
Arnd Bergmann authored
commit 105967ad upstream. gcc-7 points out an older regression: drivers/staging/iio/resolver/ad2s1210.c: In function 'ad2s1210_read_raw': drivers/staging/iio/resolver/ad2s1210.c:515:42: error: '<<' in boolean context, did you mean '<' ? [-Werror=int-in-bool-context] The original code had 'unsigned short' here, but incorrectly got converted to 'bool'. This reverts the regression and uses a normal type instead. Fixes: 29148543 ("staging:iio:resolver:ad2s1210 minimal chan spec conversion.") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Rafael J. Wysocki authored
commit cd5a6a4f upstream. Make usb_hc_died() clear the HCD_FLAG_RH_RUNNING flag for the shared HCD and set HCD_FLAG_DEAD for it, in analogy with what is done for the primary one. Among other thigs, this prevents check_root_hub_suspended() from returning -EBUSY for dead HCDs which helps to work around system suspend issues in some situations. This actually fixes occasional suspend failures on one of my test machines. Suggested-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by:
-
Bin Liu authored
commit 45d73860 upstream. commit 68fe05e2 ("usb: musb: fix tx fifo flush handling") drops the 1ms delay trying to solve the long disconnect time issue when application queued many tx urbs. However, the 1ms delay is needed for some use cases, for example, without the delay, reconnecting AR9271 WIFI dongle no longer works if the connection is dropped from the AP. So let's add back the 1ms delay in musb_h_tx_flush_fifo(), and solve the long disconnect time problem with a separate patch for usb_hcd_flush_endpoint(). Signed-off-by:
Bin Liu <b-liu@ti.com> Signed-off-by:
-
Greg Kroah-Hartman authored
commit 3b6bcd3d upstream. This adds a new ATEN device id for a new pl2303-based device. Reported-by:
Peter Kuo <PeterKuo@aten.com.tw> Cc: Johan Hovold <johan@kernel.org> Signed-off-by:
-
Stefan Triller authored
commit 9585e340 upstream. The German Telekom offers a ZigBee USB Stick under the brand name Qivicon for their SmartHome Home Base in its 1. Generation. The productId is not known by the according kernel module, this patch adds support for it. Signed-off-by:
Stefan Triller <github@stefantriller.de> Reviewed-by:
Frans Klaver <fransklaver@gmail.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Hector Martin authored
commit fd1b8668 upstream. Add device id for D-Link DWM-222. Signed-off-by:
Hector Martin <marcan@marcan.st> Signed-off-by:
-
Maarten Lankhorst authored
commit 5279fc77 upstream. bdw_load_gamma_lut is writing beyond the array to the maximum value. The intend of the function is to clamp values > 1 to 1, so write the intended color to the max register. This fixes the following KASAN warning: [ 197.020857] [IGT] kms_pipe_color: executing [ 197.063434] [IGT] kms_pipe_color: starting subtest ctm-0-25-pipe0 [ 197.078989] ================================================================== [ 197.079127] BUG: KASAN: slab-out-of-bounds in bdw_load_gamma_lut.isra.2+0x3b9/0x570 [i915] [ 197.079188] Read of size 2 at addr ffff8800d38db150 by task kms_pipe_color/1839 [ 197.079208] CPU: 2 PID: 1839 Comm: kms_pipe_color Tainted: G U 4.13.0-rc1-patser+ #5211 [ 197.079215] Hardware name: NUC5i7RYB, BIOS RYBDWi35.86A.0246.2015.0309.1355 03/09/2015 [ 197.079220] Call Trace: [ 197.079230] dump_stack+0x68/0x9e [ 197.079239] print_address_description+0x6f/0x250 [ 197.079251] kasan_report+0x216/0x370 [ 197.079374] ? bdw_load_gamma_lut.isra.2+0x3b9/0x570 [i915] [ 197.079451] ? gen8_write16+0x4e0/0x4e0 [i915] [ 197.079460] __asan_report_load2_noabort+0x14/0x20 [ 197.079535] bdw_load_gamma_lut.isra.2+0x3b9/0x570 [i915] [ 197.079612] broadwell_load_luts+0x1df/0x550 [i915] [ 197.079690] intel_color_load_luts+0x7b/0x80 [i915] [ 197.079764] intel_begin_crtc_commit+0x138/0x760 [i915] [ 197.079783] drm_atomic_helper_commit_planes_on_crtc+0x1a3/0x820 [drm_kms_helper] [ 197.079859] ? intel_pre_plane_update+0x571/0x580 [i915] [ 197.079937] intel_update_crtc+0x238/0x330 [i915] [ 197.080016] intel_update_crtcs+0x10f/0x210 [i915] [ 197.080092] intel_atomic_commit_tail+0x1552/0x3340 [i915] [ 197.080101] ? _raw_spin_unlock+0x3c/0x40 [ 197.080110] ? __queue_work+0xb40/0xbf0 [ 197.080188] ? skl_update_crtcs+0xc00/0xc00 [i915] [ 197.080195] ? trace_hardirqs_on+0xd/0x10 [ 197.080269] ? intel_atomic_commit_ready+0x128/0x13c [i915] [ 197.080329] ? __i915_sw_fence_complete+0x5b8/0x6d0 [i915] [ 197.080336] ? debug_object_activate+0x39e/0x580 [ 197.080397] ? i915_sw_fence_await+0x30/0x30 [i915] [ 197.080409] ? __might_sleep+0x15b/0x180 [ 197.080483] intel_atomic_commit+0x944/0xa70 [i915] [ 197.080490] ? refcount_dec_and_test+0x11/0x20 [ 197.080567] ? intel_atomic_commit_tail+0x3340/0x3340 [i915] [ 197.080597] ? drm_atomic_crtc_set_property+0x303/0x580 [drm] [ 197.080674] ? intel_atomic_commit_tail+0x3340/0x3340 [i915] [ 197.080704] drm_atomic_commit+0xd7/0xe0 [drm] [ 197.080722] drm_atomic_helper_crtc_set_property+0xec/0x130 [drm_kms_helper] [ 197.080749] drm_mode_crtc_set_obj_prop+0x7d/0xb0 [drm] [ 197.080775] drm_mode_obj_set_property_ioctl+0x50b/0x5d0 [drm] [ 197.080783] ? __might_fault+0x104/0x180 [ 197.080809] ? drm_mode_obj_find_prop_id+0x160/0x160 [drm] [ 197.080838] ? drm_mode_obj_find_prop_id+0x160/0x160 [drm] [ 197.080861] drm_ioctl_kernel+0x154/0x1a0 [drm] [ 197.080885] drm_ioctl+0x624/0x8f0 [drm] [ 197.080910] ? drm_mode_obj_find_prop_id+0x160/0x160 [drm] [ 197.080934] ? drm_getunique+0x210/0x210 [drm] [ 197.080943] ? __handle_mm_fault+0x1bd0/0x1ce0 [ 197.080949] ? lock_downgrade+0x610/0x610 [ 197.080957] ? __lru_cache_add+0x15a/0x180 [ 197.080967] do_vfs_ioctl+0xd92/0xe40 [ 197.080975] ? ioctl_preallocate+0x1b0/0x1b0 [ 197.080982] ? selinux_capable+0x20/0x20 [ 197.080991] ? __do_page_fault+0x7b7/0x9a0 [ 197.080997] ? lock_downgrade+0x5bb/0x610 [ 197.081007] ? security_file_ioctl+0x57/0x90 [ 197.081016] SyS_ioctl+0x4e/0x80 [ 197.081024] entry_SYSCALL_64_fastpath+0x18/0xad [ 197.081030] RIP: 0033:0x7f61f287a987 [ 197.081035] RSP: 002b:00007fff7d44d188 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 [ 197.081043] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f61f287a987 [ 197.081048] RDX: 00007fff7d44d1c0 RSI: 00000000c01864ba RDI: 0000000000000003 [ 197.081053] RBP: 00007f61f2b3eb00 R08: 0000000000000059 R09: 0000000000000000 [ 197.081058] R10: 0000002ea5c4a290 R11: 0000000000000246 R12: 00007f61f2b3eb58 [ 197.081063] R13: 0000000000001010 R14: 00007f61f2b3eb58 R15: 0000000000002702 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101659Signed-off-by:
Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Reported-by:
Martin Peres <martin.peres@linux.intel.com> Cc: Martin Peres <martin.peres@linux.intel.com> Fixes: 82cf435b ("drm/i915: Implement color management on bdw/skl/bxt/kbl") Cc: Shashank Sharma <shashank.sharma@intel.com> Cc: Kiran S Kumar <kiran.s.kumar@intel.com> Cc: Kausal Malladi <kausalmalladi@gmail.com> Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: intel-gfx@lists.freedesktop.org Link: https://patchwork.freedesktop.org/patch/msgid/20170724091431.24251-1-maarten.lankhorst@linux.intel.comReviewed-by:
Lionel Landwerlin <lionel.g.landwerlin@intel.com> (cherry picked from commit 09a92bc8) Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Wladimir J. van der Laan authored
commit d6f756e0 upstream. A relocation pointing to the last four bytes of a buffer can legitimately happen in the case of small vertex buffers. Signed-off-by:
Wladimir J. van der Laan <laanwj@gmail.com> Reviewed-by:
Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by:
Christian Gmeiner <christian.gmeiner@gmail.com> Signed-off-by:
Lucas Stach <l.stach@pengutronix.de> Signed-off-by:
-
Lucas Stach authored
commit d630213f upstream. The output node of the TC358767 is only used if another bridge is chained behind it. Panels attached to the TC358767 can be detected using the usual DP AUX probing. This restores the old behavior of ignoring the output if no endpoint is found. Fixes: ebc94461 (drm: convert drivers to use drm_of_find_panel_or_bridge) Acked-by:
Andrey Gusakov <andrey.gusakov@cogentembedded.com> Signed-off-by:
Archit Taneja <architt@codeaurora.org> Link: https://patchwork.freedesktop.org/patch/msgid/20170710124125.9019-1-l.stach@pengutronix.deSigned-off-by:
-
Weston Andros Adamson authored
commit 1feb2616 upstream. The client was freeing the nfs4_ff_layout_ds, but not the contained nfs4_ff_ds_version array. Signed-off-by:
Weston Andros Adamson <dros@primarydata.com> Signed-off-by:
Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by:
-
Haibo Chen authored
commit 92ddd959 upstream. Change the default err value to -EINVAL, make sure the card only has type EXT_CSD_CARD_TYPE_HS400_1_8V also do the signal voltage setting when select hs400es mode. Fixes: commit 1720d354 ("mmc: core: switch to 1V8 or 1V2 for hs400es mode") Signed-off-by:
Haibo Chen <haibo.chen@nxp.com> Reviewed-by:
Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Miquel Raynal authored
commit f7f8c175 upstream. When using soft ecc, if no ooblayout is given, the core automatically uses one of the nand_ooblayout_{sp,lp}*() functions to determine the layout inside the out of band data. Until kernel version 4.6, struct nand_ecclayout was used for that purpose. During the migration from 4.6 to 4.7, an error shown up in the small page layout, in the case oob section is only 8 bytes long. The layout was using three bytes (0, 1, 2) for ecc, two bytes (3, 4) as free bytes, one byte (5) for bad block marker and finally two bytes (6, 7) as free bytes, as shown there: [linux-4.6] drivers/mtd/nand/nand_base.c:52 static struct nand_ecclayout nand_oob_8 = { .eccbytes = 3, .eccpos = {0, 1, 2}, .oobfree = { {.offset = 3, .length = 2}, {.offset = 6, .length = 2} } }; This fixes the current implementation which is incoherent. It references bit 3 at the same time as an ecc byte and a free byte. Furthermore, it is clear with the previous implementation that there is only one ecc section with 8 bytes oob sections. We shall return -ERANGE in the nand_ooblayout_ecc_sp() function when asked for the second section. Signed-off-by:
Miquel Raynal <miquel.raynal@free-electrons.com> Fixes: 41b207a7 ("mtd: nand: implement the default mtd_ooblayout_ops") Signed-off-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by:
-
Hans de Goede authored
commit 682c6c21 upstream. At least the Acer Iconia Tab8 / aka W1-810 uses 1MiHz instead of 1MHz for one of its busses, fix this up to 1MHz instead of failing the probe of that bus. This fixes the accelerometer on the Acer Iconia Tab8 not working. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Mateusz Jurczyk authored
commit 68227c03 upstream. Before the patch, the flock flag could remain uninitialized for the lifespan of the fuse_file allocation. Unless set to true in fuse_file_flock(), it would remain in an indeterminate state until read in an if statement in fuse_release_common(). This could consequently lead to taking an unexpected branch in the code. The bug was discovered by a runtime instrumentation designed to detect use of uninitialized memory in the kernel. Signed-off-by:
Mateusz Jurczyk <mjurczyk@google.com> Fixes: 37fb3a30 ("fuse: fix flock") Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Signed-off-by:
-
Nicholas Bellinger authored
commit 6f48655f upstream. This patch fixes a generate_node_acls = 1 + cache_dynamic_acls = 0 regression, that was introduced by commit 01d4d673 Author: Nicholas Bellinger <nab@linux-iscsi.org> Date: Wed Dec 7 12:55:54 2016 -0800 which originally had the proper list_del_init() usage, but was dropped during list review as it was thought unnecessary by HCH. However, list_del_init() usage is required during the special generate_node_acls = 1 + cache_dynamic_acls = 0 case when transport_free_session() does a list_del(&se_nacl->acl_list), followed by target_complete_nacl() doing the same thing. This was manifesting as a general protection fault as reported by Justin: kernel: general protection fault: 0000 [#1] SMP kernel: Modules linked in: kernel: CPU: 0 PID: 11047 Comm: iscsi_ttx Not tainted 4.13.0-rc2.x86_64.1+ #20 kernel: Hardware name: Intel Corporation S5500BC/S5500BC, BIOS S5500.86B.01.00.0064.050520141428 05/05/2014 kernel: task: ffff88026939e800 task.stack: ffffc90007884000 kernel: RIP: 0010:target_put_nacl+0x49/0xb0 kernel: RSP: 0018:ffffc90007887d70 EFLAGS: 00010246 kernel: RAX: dead000000000200 RBX: ffff8802556ca000 RCX: 0000000000000000 kernel: RDX: dead000000000100 RSI: 0000000000000246 RDI: ffff8802556ce028 kernel: RBP: ffffc90007887d88 R08: 0000000000000001 R09: 0000000000000000 kernel: R10: ffffc90007887df8 R11: ffffea0009986900 R12: ffff8802556ce020 kernel: R13: ffff8802556ce028 R14: ffff8802556ce028 R15: ffffffff88d85540 kernel: FS: 0000000000000000(0000) GS:ffff88027fc00000(0000) knlGS:0000000000000000 kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 kernel: CR2: 00007fffe36f5f94 CR3: 0000000009209000 CR4: 00000000003406f0 kernel: DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 kernel: DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 kernel: Call Trace: kernel: transport_free_session+0x67/0x140 kernel: transport_deregister_session+0x7a/0xc0 kernel: iscsit_close_session+0x92/0x210 kernel: iscsit_close_connection+0x5f9/0x840 kernel: iscsit_take_action_for_connection_exit+0xfe/0x110 kernel: iscsi_target_tx_thread+0x140/0x1e0 kernel: ? wait_woken+0x90/0x90 kernel: kthread+0x124/0x160 kernel: ? iscsit_thread_get_cpumask+0x90/0x90 kernel: ? kthread_create_on_node+0x40/0x40 kernel: ret_from_fork+0x22/0x30 kernel: Code: 00 48 89 fb 4c 8b a7 48 01 00 00 74 68 4d 8d 6c 24 08 4c 89 ef e8 e8 28 43 00 48 8b 93 20 04 00 00 48 8b 83 28 04 00 00 4c 89 ef <48> 89 42 08 48 89 10 48 b8 00 01 00 00 00 00 ad de 48 89 83 20 kernel: RIP: target_put_nacl+0x49/0xb0 RSP: ffffc90007887d70 kernel: ---[ end trace f12821adbfd46fed ]--- To address this, go ahead and use proper list_del_list() for all cases of se_nacl->acl_list deletion. Reported-by:
Justin Maggard <jmaggard01@gmail.com> Tested-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Alan Stern authored
commit 8b52291a upstream. Christoph Hellwig says that since version 4.12, the kernel switched to using blk-mq by default. The old code used a softirq for handling request completions, but blk-mq can handle completions in the caller's context. This may cause a problem for usb-storage, because it invokes the ->scsi_done callback while holding the host lock, and the completion routine sometimes tries to acquire the same lock (when running the error handler, for example). The consequence is that the existing code will sometimes deadlock upon error completion of a SCSI command (with a lockdep warning). This is easy enough to fix, since usb-storage doesn't really need to hold the host lock while the callback runs. It was simpler to write it that way, but moving the call outside the locked region is pretty easy and there's no downside. That's what this patch does. Signed-off-by:
Arthur Marsh <arthur.marsh@internode.on.net> CC: Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Nicholas Bellinger authored
commit 978d13d6 upstream. This patch fixes a bug associated with iscsit_reset_np_thread() that can occur during parallel configfs rmdir of a single iscsi_np used across multiple iscsi-target instances, that would result in hung task(s) similar to below where configfs rmdir process context was blocked indefinately waiting for iscsi_np->np_restart_comp to finish: [ 6726.112076] INFO: task dcp_proxy_node_:15550 blocked for more than 120 seconds. [ 6726.119440] Tainted: G W O 4.1.26-3321 #2 [ 6726.125045] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 6726.132927] dcp_proxy_node_ D ffff8803f202bc88 0 15550 1 0x00000000 [ 6726.140058] ffff8803f202bc88 ffff88085c64d960 ffff88083b3b1ad0 ffff88087fffeb08 [ 6726.147593] ffff8803f202c000 7fffffffffffffff ffff88083f459c28 ffff88083b3b1ad0 [ 6726.155132] ffff88035373c100 ffff8803f202bca8 ffffffff8168ced2 ffff8803f202bcb8 [ 6726.162667] Call Trace: [ 6726.165150] [<ffffffff8168ced2>] schedule+0x32/0x80 [ 6726.170156] [<ffffffff8168f5b4>] schedule_timeout+0x214/0x290 [ 6726.176030] [<ffffffff810caef2>] ? __send_signal+0x52/0x4a0 [ 6726.181728] [<ffffffff8168d7d6>] wait_for_completion+0x96/0x100 [ 6726.187774] [<ffffffff810e7c80>] ? wake_up_state+0x10/0x10 [ 6726.193395] [<ffffffffa035d6e2>] iscsit_reset_np_thread+0x62/0xe0 [iscsi_target_mod] [ 6726.201278] [<ffffffffa0355d86>] iscsit_tpg_disable_portal_group+0x96/0x190 [iscsi_target_mod] [ 6726.210033] [<ffffffffa0363f7f>] lio_target_tpg_store_enable+0x4f/0xc0 [iscsi_target_mod] [ 6726.218351] [<ffffffff81260c5a>] configfs_write_file+0xaa/0x110 [ 6726.224392] [<ffffffff811ea364>] vfs_write+0xa4/0x1b0 [ 6726.229576] [<ffffffff811eb111>] SyS_write+0x41/0xb0 [ 6726.234659] [<ffffffff8169042e>] system_call_fastpath+0x12/0x71 It would happen because each iscsit_reset_np_thread() sets state to ISCSI_NP_THREAD_RESET, sends SIGINT, and then blocks waiting for completion on iscsi_np->np_restart_comp. However, if iscsi_np was active processing a login request and more than a single iscsit_reset_np_thread() caller to the same iscsi_np was blocked on iscsi_np->np_restart_comp, iscsi_np kthread process context in __iscsi_target_login_thread() would flush pending signals and only perform a single completion of np->np_restart_comp before going back to sleep within transport specific iscsit_transport->iscsi_accept_np code. To address this bug, add a iscsi_np->np_reset_count and update __iscsi_target_login_thread() to keep completing np->np_restart_comp until ->np_reset_count has reached zero. Reported-by:
Gary Guo <ghg@datera.io> Tested-by:
-
Varun Prakash authored
commit ea8dc5b4 upstream. On receiving text request iscsi-target allocates buffer for payload in iscsit_handle_text_cmd() and assigns buffer pointer to cmd->text_in_ptr, this buffer is currently freed in iscsit_release_cmd(), if iscsi-target sets 'C' bit in text response then it will receive another text request from the initiator with ttt != 0xffffffff in this case iscsi-target will find cmd using itt and call iscsit_setup_text_cmd() which will set cmd->text_in_ptr to NULL without freeing previously allocated buffer. This patch fixes this issue by calling kfree(cmd->text_in_ptr) in iscsit_setup_text_cmd() before assigning NULL to it. For the first text request cmd->text_in_ptr is NULL as cmd is memset to 0 in iscsit_allocate_cmd(). Signed-off-by:
Varun Prakash <varun@chelsio.com> Signed-off-by:
-
Boris Brezillon authored
commit 6d292310 upstream. All timings in nand_sdr_timings are expressed in picoseconds but some of them may not fit in an u32. Signed-off-by:
Alexander Dahl <ada@thorsis.com> Reviewed-by:
-
Boris Brezillon authored
commit a11bf5ed upstream. Some ONFI NANDs do not support the SET/GET FEATURES commands, which, according to the spec, is perfectly valid. On these NANDs we can't set a specific timing mode using the "timing mode" feature, and we should assume the NAND does not require any setup to enter a specific timing mode. Signed-off-by:
-
Boris Brezillon authored
commit 3aa09076 upstream. PMECC caps extraction from old DT bindings is broken, thus leading to erroneous EL registers offset, which in turn make HW ECC unusable on sama5d2 when old bindings are in use. Passing the NAND dev node instead of the NFC node to of_match_node() solves the problem. Signed-off-by:
Romain Izard <romain.izard.pro@gmail.com> Signed-off-by:
-
Gregory CLEMENT authored
commit 6b67c390 upstream. On the south bridge we have pin from to 29, so it gives 30 pins (and not 29). Without this patch the kernel complain with the following traces: cat /sys/kernel/debug/pinctrl/d0018800.pinctrl/pingroups [ 154.530205] armada-37xx-pinctrl d0018800.pinctrl: failed to get pin(29) name [ 154.537567] ------------[ cut here ]------------ [ 154.542348] WARNING: CPU: 1 PID: 1347 at /home/gclement/open/kernel/marvell-mainline-linux/drivers/pinctrl/core.c:1610 pinctrl_groups_show+0x15c/0x1a0 [ 154.555918] Modules linked in: [ 154.558890] CPU: 1 PID: 1347 Comm: cat Tainted: G W 4.13.0-rc1-00001-g19e1b9fa219d #525 [ 154.568316] Hardware name: Marvell Armada 3720 Development Board DB-88F3720-DDR3 (DT) [ 154.576311] task: ffff80001d32d100 task.stack: ffff80001bdc0000 [ 154.583048] PC is at pinctrl_groups_show+0x15c/0x1a0 [ 154.587816] LR is at pinctrl_groups_show+0x148/0x1a0 [ 154.592847] pc : [<ffff0000083e3adc>] lr : [<ffff0000083e3ac8>] pstate: 00000145 [ 154.600840] sp : ffff80001bdc3c80 [ 154.604255] x29: ffff80001bdc3c80 x28: 00000000f7750000 [ 154.609825] x27: ffff80001d05d198 x26: 0000000000000009 [ 154.615224] x25: ffff0000089ead20 x24: 0000000000000002 [ 154.620705] x23: ffff000008c8e1d0 x22: ffff80001be55700 [ 154.626187] x21: ffff80001d05d100 x20: 0000000000000005 [ 154.631667] x19: 0000000000000006 x18: 0000000000000010 [ 154.637238] x17: 0000000000000000 x16: ffff0000081fc4b8 [ 154.642726] x15: 0000000000000006 x14: ffff0000899e537f [ 154.648214] x13: ffff0000099e538d x12: 206f742064656c69 [ 154.653613] x11: 6166203a6c727463 x10: 0000000005f5e0ff [ 154.659094] x9 : ffff80001bdc38c0 x8 : 286e697020746567 [ 154.664576] x7 : ffff000008551870 x6 : 000000000000011b [ 154.670146] x5 : 0000000000000000 x4 : 0000000000000000 [ 154.675544] x3 : 0000000000000000 x2 : 0000000000000000 [ 154.681025] x1 : ffff000008c8e1d0 x0 : ffff80001be55700 [ 154.686507] Call trace: [ 154.688668] Exception stack(0xffff80001bdc3ab0 to 0xffff80001bdc3be0) [ 154.695224] 3aa0: 0000000000000006 0001000000000000 [ 154.703310] 3ac0: ffff80001bdc3c80 ffff0000083e3adc ffff80001bdc3bb0 00000000ffffffd8 [ 154.711304] 3ae0: 4554535953425553 6f6674616c703d4d 4349564544006d72 6674616c702b3d45 [ 154.719478] 3b00: 313030643a6d726f 6e69702e30303838 ffff80006c727463 ffff0000089635d8 [ 154.727562] 3b20: ffff80001d1ca0cb ffff000008af0fa4 ffff80001bdc3b40 ffff000008c8e1dc [ 154.735648] 3b40: ffff80001bdc3bc0 ffff000008223174 ffff80001be55700 ffff000008c8e1d0 [ 154.743731] 3b60: 0000000000000000 0000000000000000 0000000000000000 0000000000000000 [ 154.752354] 3b80: 000000000000011b ffff000008551870 286e697020746567 ffff80001bdc38c0 [ 154.760446] 3ba0: 0000000005f5e0ff 6166203a6c727463 206f742064656c69 ffff0000099e538d [ 154.767910] 3bc0: ffff0000899e537f 0000000000000006 ffff0000081fc4b8 0000000000000000 [ 154.776085] [<ffff0000083e3adc>] pinctrl_groups_show+0x15c/0x1a0 [ 154.782823] [<ffff000008222abc>] seq_read+0x184/0x460 [ 154.787505] [<ffff000008344120>] full_proxy_read+0x60/0xa8 [ 154.793431] [<ffff0000081f9bec>] __vfs_read+0x1c/0x110 [ 154.799001] [<ffff0000081faff4>] vfs_read+0x84/0x140 [ 154.803860] [<ffff0000081fc4fc>] SyS_read+0x44/0xa0 [ 154.808983] [<ffff000008082f30>] el0_svc_naked+0x24/0x28 [ 154.814459] ---[ end trace 4cbb00a92d616b95 ]--- Fixes: 87466ccd ("pinctrl: armada-37xx: Add pin controller support for Armada 37xx") Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Jan Kara authored
commit ea7bd56f upstream. The bio describing discard operation is allocated by __blkdev_issue_discard() which returns us a reference to it. That reference is never released and thus we leak this bio. Drop the bio reference once it completes in xlog_discard_endio(). Fixes: 4560e78fSigned-off-by:
Jan Kara <jack@suse.cz> Reviewed-by:
Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by:
-
Max Filippov authored
commit 7f81e55c upstream. csum_partial and csum_partial_copy_generic are defined unconditionally and are available even when CONFIG_NET is disabled. They are used not only by the network drivers, but also by scsi and media. Don't limit these functions export by CONFIG_NET. Signed-off-by:
Max Filippov <jcmvbkbc@gmail.com> Signed-off-by:
-
Max Filippov authored
commit bc652eb6 upstream. Functions clear_user_highpage, copy_user_highpage, flush_dcache_page, local_flush_cache_range and local_flush_cache_page may be used from modules. Export them. Signed-off-by:
-
Max Filippov authored
commit 6d0f581d upstream. Currently building kernel for xtensa core with aliasing WT cache fails with the following messages: mm/memory.c:2152: undefined reference to `flush_dcache_page' mm/memory.c:2332: undefined reference to `local_flush_cache_page' mm/memory.c:1919: undefined reference to `local_flush_cache_range' mm/memory.c:4179: undefined reference to `copy_to_user_page' mm/memory.c:4183: undefined reference to `copy_from_user_page' This happens because implementation of these functions is only compiled when data cache is WB, which looks wrong: even when data cache doesn't need flushing it still needs invalidation. The functions like __flush_[invalidate_]dcache_* are correctly defined for both WB and WT caches (and even if they weren't that'd still be ok, just slower). Fix this by providing the same implementation of the above functions for both WB and WT cache. Signed-off-by:
-
Mel Gorman authored
commit 48fb6f4d upstream. Commit 65d8fc77 ("futex: Remove requirement for lock_page() in get_futex_key()") removed an unnecessary lock_page() with the side-effect that page->mapping needed to be treated very carefully. Two defensive warnings were added in case any assumption was missed and the first warning assumed a correct application would not alter a mapping backing a futex key. Since merging, it has not triggered for any unexpected case but Mark Rutland reported the following bug triggering due to the first warning. kernel BUG at kernel/futex.c:679! Internal error: Oops - BUG: 0 [#1] PREEMPT SMP Modules linked in: CPU: 0 PID: 3695 Comm: syz-executor1 Not tainted 4.13.0-rc3-00020-g307fec773ba3 #3 Hardware name: linux,dummy-virt (DT) task: ffff80001e271780 task.stack: ffff000010908000 PC is at get_futex_key+0x6a4/0xcf0 kernel/futex.c:679 LR is at get_futex_key+0x6a4/0xcf0 kernel/futex.c:679 pc : [<ffff00000821ac14>] lr : [<ffff00000821ac14>] pstate: 80000145 The fact that it's a bug instead of a warning was due to an unrelated arm64 problem, but the warning itself triggered because the underlying mapping changed. This is an application issue but from a kernel perspective it's a recoverable situation and the warning is unnecessary so this patch removes the warning. The warning may potentially be triggered with the following test program from Mark although it may be necessary to adjust NR_FUTEX_THREADS to be a value smaller than the number of CPUs in the system. #include <linux/futex.h> #include <pthread.h> #include <stdio.h> #include <stdlib.h> #include <sys/mman.h> #include <sys/syscall.h> #include <sys/time.h> #include <unistd.h> #define NR_FUTEX_THREADS 16 pthread_t threads[NR_FUTEX_THREADS]; void *mem; #define MEM_PROT (PROT_READ | PROT_WRITE) #define MEM_SIZE 65536 static int futex_wrapper(int *uaddr, int op, int val, const struct timespec *timeout, int *uaddr2, int val3) { syscall(SYS_futex, uaddr, op, val, timeout, uaddr2, val3); } void *poll_futex(void *unused) { for (;;) { futex_wrapper(mem, FUTEX_CMP_REQUEUE_PI, 1, NULL, mem + 4, 1); } } int main(int argc, char *argv[]) { int i; mem = mmap(NULL, MEM_SIZE, MEM_PROT, MAP_SHARED | MAP_ANONYMOUS, -1, 0); printf("Mapping @ %p\n", mem); printf("Creating futex threads...\n"); for (i = 0; i < NR_FUTEX_THREADS; i++) pthread_create(&threads[i], NULL, poll_futex, NULL); printf("Flipping mapping...\n"); for (;;) { mmap(mem, MEM_SIZE, MEM_PROT, MAP_FIXED | MAP_SHARED | MAP_ANONYMOUS, -1, 0); } return 0; } Reported-and-tested-by:
Mark Rutland <mark.rutland@arm.com> Signed-off-by:
Mel Gorman <mgorman@suse.de> Acked-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Cong Wang authored
commit d041353d upstream. We saw many list corruption warnings on shmem shrinklist: WARNING: CPU: 18 PID: 177 at lib/list_debug.c:59 __list_del_entry+0x9e/0xc0 list_del corruption. prev->next should be ffff9ae5694b82d8, but was ffff9ae5699ba960 Modules linked in: intel_rapl sb_edac edac_core x86_pkg_temp_thermal coretemp iTCO_wdt iTCO_vendor_support crct10dif_pclmul crc32_pclmul ghash_clmulni_intel raid0 dcdbas shpchp wmi hed i2c_i801 ioatdma lpc_ich i2c_smbus acpi_cpufreq tcp_diag inet_diag sch_fq_codel ipmi_si ipmi_devintf ipmi_msghandler igb ptp crc32c_intel pps_core i2c_algo_bit i2c_core dca ipv6 crc_ccitt CPU: 18 PID: 177 Comm: kswapd1 Not tainted 4.9.34-t3.el7.twitter.x86_64 #1 Hardware name: Dell Inc. PowerEdge C6220/0W6W6G, BIOS 2.2.3 11/07/2013 Call Trace: dump_stack+0x4d/0x66 __warn+0xcb/0xf0 warn_slowpath_fmt+0x4f/0x60 __list_del_entry+0x9e/0xc0 shmem_unused_huge_shrink+0xfa/0x2e0 shmem_unused_huge_scan+0x20/0x30 super_cache_scan+0x193/0x1a0 shrink_slab.part.41+0x1e3/0x3f0 shrink_slab+0x29/0x30 shrink_node+0xf9/0x2f0 kswapd+0x2d8/0x6c0 kthread+0xd7/0xf0 ret_from_fork+0x22/0x30 WARNING: CPU: 23 PID: 639 at lib/list_debug.c:33 __list_add+0x89/0xb0 list_add corruption. prev->next should be next (ffff9ae5699ba960), but was ffff9ae5694b82d8. (prev=ffff9ae5694b82d8). Modules linked in: intel_rapl sb_edac edac_core x86_pkg_temp_thermal coretemp iTCO_wdt iTCO_vendor_support crct10dif_pclmul crc32_pclmul ghash_clmulni_intel raid0 dcdbas shpchp wmi hed i2c_i801 ioatdma lpc_ich i2c_smbus acpi_cpufreq tcp_diag inet_diag sch_fq_codel ipmi_si ipmi_devintf ipmi_msghandler igb ptp crc32c_intel pps_core i2c_algo_bit i2c_core dca ipv6 crc_ccitt CPU: 23 PID: 639 Comm: systemd-udevd Tainted: G W 4.9.34-t3.el7.twitter.x86_64 #1 Hardware name: Dell Inc. PowerEdge C6220/0W6W6G, BIOS 2.2.3 11/07/2013 Call Trace: dump_stack+0x4d/0x66 __warn+0xcb/0xf0 warn_slowpath_fmt+0x4f/0x60 __list_add+0x89/0xb0 shmem_setattr+0x204/0x230 notify_change+0x2ef/0x440 do_truncate+0x5d/0x90 path_openat+0x331/0x1190 do_filp_open+0x7e/0xe0 do_sys_open+0x123/0x200 SyS_open+0x1e/0x20 do_syscall_64+0x61/0x170 entry_SYSCALL64_slow_path+0x25/0x25 The problem is that shmem_unused_huge_shrink() moves entries from the global sbinfo->shrinklist to its local lists and then releases the spinlock. However, a parallel shmem_setattr() could access one of these entries directly and add it back to the global shrinklist if it is removed, with the spinlock held. The logic itself looks solid since an entry could be either in a local list or the global list, otherwise it is removed from one of them by list_del_init(). So probably the race condition is that, one CPU is in the middle of INIT_LIST_HEAD() but the other CPU calls list_empty() which returns true too early then the following list_add_tail() sees a corrupted entry. list_empty_careful() is designed to fix this situation. [akpm@linux-foundation.org: add comments] Link: http://lkml.kernel.org/r/20170803054630.18775-1-xiyou.wangcong@gmail.com Fixes: 779750d2 ("shmem: split huge pages beyond i_size under memory pressure") Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Acked-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Hugh Dickins <hughd@google.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Jonathan Toppins authored
commit 75dddef3 upstream. The RDMA subsystem can generate several thousand of these messages per second eventually leading to a kernel crash. Ratelimit these messages to prevent this crash. Doug said: "I've been carrying a version of this for several kernel versions. I don't remember when they started, but we have one (and only one) class of machines: Dell PE R730xd, that generate these errors. When it happens, without a rate limit, we get rcu timeouts and kernel oopses. With the rate limit, we just get a lot of annoying kernel messages but the machine continues on, recovers, and eventually the memory operations all succeed" And: "> Well... why are all these EBUSY's occurring? It sounds inefficient > (at least) but if it is expected, normal and unavoidable then > perhaps we should just remove that message altogether? I don't have an answer to that question. To be honest, I haven't looked real hard. We never had this at all, then it started out of the blue, but only on our Dell 730xd machines (and it hits all of them), but no other classes or brands of machines. And we have our 730xd machines loaded up with different brands and models of cards (for instance one dedicated to mlx4 hardware, one for qib, one for mlx5, an ocrdma/cxgb4 combo, etc), so the fact that it hit all of the machines meant it wasn't tied to any particular brand/model of RDMA hardware. To me, it always smelled of a hardware oddity specific to maybe the CPUs or mainboard chipsets in these machines, so given that I'm not an mm expert anyway, I never chased it down. A few other relevant details: it showed up somewhere around 4.8/4.9 or thereabouts. It never happened before, but the prinkt has been there since the 3.18 days, so possibly the test to trigger this message was changed, or something else in the allocator changed such that the situation started happening on these machines? And, like I said, it is specific to our 730xd machines (but they are all identical, so that could mean it's something like their specific ram configuration is causing the allocator to hit this on these machine but not on other machines in the cluster, I don't want to say it's necessarily the model of chipset or CPU, there are other bits of identicalness between these machines)" Link: http://lkml.kernel.org/r/499c0f6cc10d6eb829a67f2a4d75b4228a9b356e.1501695897.git.jtoppins@redhat.comSigned-off-by:
Jonathan Toppins <jtoppins@redhat.com> Reviewed-by:
Doug Ledford <dledford@redhat.com> Tested-by:
-
- 13 Aug, 2017 2 commits
-
-
Greg Kroah-Hartman authored
-
Qu Wenruo authored
commit 848c23b7 upstream. Commit 4751832d ("btrfs: fiemap: Cache and merge fiemap extent before submit it to user") introduced a warning to catch unemitted cached fiemap extent. However such warning doesn't take the following case into consideration: 0 4K 8K |<---- fiemap range --->| |<----------- On-disk extent ------------------>| In this case, the whole 0~8K is cached, and since it's larger than fiemap range, it break the fiemap extent emit loop. This leaves the fiemap extent cached but not emitted, and caught by the final fiemap extent sanity check, causing kernel warning. This patch removes the kernel warning and renames the sanity check to emit_last_fiemap_cache() since it's possible and valid to have cached fiemap extent. Reported-by:
David Sterba <dsterba@suse.cz> Reported-by:
Adam Borowski <kilobyte@angband.pl> Fixes: 4751832d ("btrfs: fiemap: Cache and merge fiemap extent ...") Signed-off-by:
Qu Wenruo <quwenruo@cn.fujitsu.com> Signed-off-by:
David Sterba <dsterba@suse.com> Cc: Holger Hoffstätte <holger@applied-asynchrony.com> Signed-off-by:
-
