- 08 Mar, 2020 23 commits
-
-
David Heidelberg authored
Based on: - 3320A in-kernel driver - https://www.spinics.net/lists/linux-iio/msg25145.html - https://lore.kernel.org/patchwork/patch/684179/ I decided to keep it aside of AL3320A due to different approach and much simpler design of 3010. Tested on Nexus 7 2012 (grouper/tilapia). Tested-by:
David Heidelberg <david@ixit.cz> Tested-by:
Dmitry Osipenko <digetx@gmail.com> Tested-by:
Michał Mirosław <mirq-linux@rere.qmqm.pl> Reviewed-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
David Heidelberg authored
- modified to be in part with al3010 driver - cleanup using bitfield, no functionality change intended Signed-off-by:
-
David Heidelberg authored
The Dyna-Image AL3010 is a 16-bit digital ambient light sensor which provides a multiple gain function with linear response over a dynamic range 1216/4863/19452/77806. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
David Heidelberg authored
This commit add dt-bindings support to al3320a driver and vendor-prefix dynaimage. Partly based on unmerged commit: "iio: Add Dyna-Image AP3223 ambient light and proximity driver" Signed-off-by:
-
Alexandru Tachici authored
Move ad7192 ADC driver out of staging into mainline. Signed-off-by:
Alexandru Tachici <alexandru.tachici@analog.com> Signed-off-by:
-
Alexandru Tachici authored
Updated mainline documentation on ad7192 userspace sysfs. Signed-off-by:
-
Alexandru Tachici authored
This patch removes spi_device_id table and moves the init data (id of the chip) in the .data field of of_device_id table. Signed-off-by:
-
Alexandru Tachici authored
This patch changes the static const struct iio_chan_spec arrays in a way that all the necessary attributes are set at compile time. Now ad7192_channels_config only makes the channels attribute of iio_dev point to the right array depending on the chip. Signed-off-by:
-
Alexandru Tachici authored
This patch makes the ad7192_probe fail in case regulator_get_voltage will return an error or voltage is set to 0. Signed-off-by:
-
Mircea Caprioru authored
This patch adds the posibility do read and write registers from userspace using the kernel debug direct register access option. Signed-off-by:
Mircea Caprioru <mircea.caprioru@analog.com> Signed-off-by:
-
Nuno Sá authored
All of the actions done in `adis16460_initial_setup()` are now done in `__adis_initial_startup()` so, there's no need for code duplication. Signed-off-by:
Nuno Sá <nuno.sa@analog.com> Signed-off-by:
Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by:
-
Nuno Sá authored
All actions done in `adis16480_initial_setup()` are now done in `__adis_initial_startup()` so, there's no need for code duplication. Furthermore, the call to `adis16480_initial_setup()` is done before any device configuration since the device will be reset if not already (via rst pin). This is actually fixing a potential bug since `adis_reset()` was being called after configuring the device which is obviously a problem. Signed-off-by:
-
Alexandru Ardelean authored
Each driver/chip that wants to validate it's product id, can now specify a 'prod_id_reg' and an expected 'prod_id' value. The 'prod_id' value is intentionally left 0 (uninitialized). There aren't (yet) any product IDs with value 0; this enforces that both 'prod_id_reg' and 'prod_id' are specified. At the very least, this routine validates that the SPI connection to the ADIS chip[s] works well. Signed-off-by:
-
Nuno Sá authored
All the ADIS devices perform, at the beginning, a self test to make sure the device is in a sane state. Previously, the logic was that the self-test was performed in adis_initial_startup() and if that failed a reset was done and then a self-test was attempted again. This change unifies the reset mechanism under the adis_initial_startup() call. A HW reset will be done if GPIO is configured, or a SW reset otherwise. This should make sure that the chip is in a sane state for self-test. Once the reset is done, the self-test operation will be performed. If anything goes wrong with self-test, the driver should just bail/error-out (i.e. no second attempt). The chip would likely not be a in a sane state state if the self-test fails after a reset. Signed-off-by:
-
Nuno Sá authored
This patch adds a dedicated self_test_reg variable. This is also a step to let new drivers make use of `adis_initial_startup()`. Some devices use MSG_CTRL reg to request a self_test command while others use the GLOB_CMD register. Signed-off-by:
-
Alexandru Ardelean authored
This change splits the __adis_initial_startup() away from adis_initial_startup(). The unlocked version can be used in certain calls during probe, where races won't happen since the ADIS driver may not be registered yet with IIO. Signed-off-by:
-
Alexandru Ardelean authored
This change overrides commit 380b107b ("iio: adis: Introduce timeouts structure"). It removes the memory allocation and moves the 'adis_data' information to be static on the chip_info struct. This also adds a timeout structure to ADIS16334, since it was initially omitted. This was omitted (by accident) when the change was done. Signed-off-by:
-
Alexandru Ardelean authored
This change overrides commit 380b107b ("iio: adis: Introduce timeouts structure"). It removes the memory allocation and moves the 'adis_data' information to be static on the chip_info struct. This also adds a timeout structure to ADIS16334, since it was initially omitted. This was omitted (by accident) when the change was done. Signed-off-by:
-
Alexandru Ardelean authored
This change overrides commit 380b107b ("iio: adis: Introduce timeouts structure"). It removes the memory allocation and moves the 'adis_data' information to be static on the chip_info struct. Signed-off-by:
-
Lorenzo Bianconi authored
Add missing return value check in st_lsm6dsx_shub_read_oneshot disabling the slave device connected to the st_lsm6dsx i2c controller. The issue is reported by coverity with the following error: Unchecked return value: If the function returns an error value, the error value may be mistaken for a normal value. Addresses-Coverity-ID: 1456767 ("Unchecked return value") Signed-off-by:Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by:
-
Beniamin Bia authored
Add Beniamin Bia and Michael Hennerich as maintainers for HMC425A attenuator. Signed-off-by:
Beniamin Bia <beniamin.bia@analog.com> Signed-off-by:
-
Michael Hennerich authored
Document support for Analog Devices MC425A Step Attenuator. Signed-off-by:
Michael Hennerich <michael.hennerich@analog.com> Signed-off-by:
-
Michael Hennerich authored
This patch adds support for the HMC425A 0.5 dB LSB GaAs MMIC 6-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, 2.2 - 8.0 GHz. Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/hmc425A.pdfSigned-off-by:
-
- 21 Feb, 2020 4 commits
-
-
Beniamin Bia authored
This patch add write_raw_get_fmt function to specify conversion for hardware gain. Signed-off-by:
-
Beniamin Bia authored
This patch handles the db suffix used for writing micro db values. Signed-off-by:
-
Fabrice Gasnier authored
The stm32-timer-cnt driver doesn't use the iio interface. The iio headers aren't relevant and can be removed as reported by William in [1]. With this change, mod_devicetable.h needs to be added to define the 'of_device_id' struct. [1] https://lkml.org/lkml/2020/2/10/1516Reported-by:
William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by:
Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by:
-
Fabrice Gasnier authored
Add suspend/resume PM sleep ops. When going to low power, enforce the counter isn't active. Gracefully restore its state upon resume in case it's been left enabled prior to suspend. Acked-by:
-
- 14 Feb, 2020 13 commits
-
-
Jean-Baptiste Maneyrol authored
Add missing mpu6000 and new icm20609, icm20689, icm20690, and iam20680. Signed-off-by:
Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Signed-off-by:
-
Jean-Baptiste Maneyrol authored
As every chip has some little variant in LPF bandwidth values, use common values that are working for all chips. Simplify the LPF setting function. Signed-off-by:
-
Jean-Baptiste Maneyrol authored
Same generation as ICM20602 but different registers. Signed-off-by:
-
Jean-Baptiste Maneyrol authored
Automotive certified IMU, similar to ICM20608. Signed-off-by:
-
Jean-Baptiste Maneyrol authored
They are similar to ICM20608 chip. Signed-off-by:
-
Jean-Baptiste Maneyrol authored
Use device_get_match_data for using of and acpi tables. In spi support add missing mpu6515 and of match table. Reorganize Kconfig to display chips grouped by generations. Signed-off-by:
-
Tomer Maimon authored
Modify NPCM ADC reset support from direct register access to reset controller support. please make sure to modify NPCM adc device tree parameters as described at nuvoton,npcm-adc.txt document for using this change. Note for anyone noting that this is a breaking change, this is on a BMC and effectively in a close ecosystem so it is fine to rely on DT and kernel being updated together. Signed-off-by:
Tomer Maimon <tmaimon77@gmail.com> Signed-off-by:
-
Tomer Maimon authored
Add NPCM ADC reset binding documentation. Signed-off-by:
-
Guido Günther authored
This is modelled after the vcnl4035 driver. For the vcnl40{0,1,2}0 we don't do anything since they use on demand measurement. Signed-off-by:Guido Günther <agx@sigxcpu.org> Signed-off-by:
-
Guido Günther authored
This will be useful when introducing runtime pm. Signed-off-by:
-
Uwe Kleine-König authored
These two defines are unused since the driver was introduced in commit 02b829f9 ("iio: dac: Add support for ltc2632 DACs"). Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Uwe Kleine-König authored
The only difference between LTC2632 and LTC2636 is that the former has two DAC channels while the latter has eight. Signed-off-by:
-
Uwe Kleine-König authored
The channel data for ltc2632l12 and ltc2632h12 are identical. So there is no gain in using two different (but identical) channel descriptions. The only side effect of this change is some memory savings. Signed-off-by:
-
