This is a follow-up to patch "ieee1394: sbp2: enable auto spin-up for
Maxtor disks".  When I 'ejected' an OXUF922 based HDD from a Mac OS X
box, it was spun down by the Mac and did not spin up by itself when
attached to a Linux box right after that.  The first SCSI command that
required the bridge to access the drive ended in
sda:<6>sd 18:0:0:0: Device not ready: <6>: Current: sense key: Not Ready
    Additional sense: Logical unit not ready, initializing cmd. required

Therefore the flag which instructs scsi_mod to send START STOP UNIT with
START=1 ("make medium ready") after such a condition is now enabled
unconditionally for all FireWire storage devices.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

 - Stefan Richter snatches Jody's place
 - update path to linux1394.org's repo
 - remove now redundant entries of ohci1394 and sbp2
 - promote eth1394 from Orphaned to Odd Fixes
 - Stefan takes patches to pcilynx but doesn't have the hardware
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Some of the suspend and resume litany may fail.
Tell the PCI core about it.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Put firewire host controller in PCI Dx state for system suspend.
(I was not able to measure any power savings, but it sounds like right
thing to do, anyway.)
Signed-off-by: Pavel Machek <pavel@suse.cz>

Update by stefanr:  Shuffle with existing PPC_PMAC code.  Set power
state in the resume hook too.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Rename ohci1394's packet_swab to header_le32_to_cpu to better reflect
what it actually does.  Also, define a constant array as 'const' and
check the array index properly.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

The transaction labels were misprinted int the debug printk "Packet
received from node..." due two byte-swapping once too often.  Affected
were big endian machines, except UniNorth based ones.  Fix tested by
Wolfgang Pfeiffer.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

In the old days, sbp2 used to coerce all MODE SENSE commands into the
10 bytes version.  When all command set conversions were removed from
sbp2 several months ago, sdev->use_10_for_ms = 1 was added.  Meaning,
higher SCSI layers preferred the 10 bytes version but would try the 6
bytes version if the former failed.

Recently, a problem with the 10 bytes version was discovered.  An Initio
INIC-1530 firmware accepted the 10 bytes version but replied with bogus
data, showing the HDD incorrectly as write-protected.  Since RBC
actually mandates MODE SENSE (6), I checked which version was sent by
Windows XP and Mac OS X 10.3 to an SBP-2 target hosted by Linux --- it
was the 6 bytes version.  (Exception: OS X sent the 10 bytes version to
an MMC target.  RBC and SBC got MODE SENSE (6).)

Therefore, drop the use_10_for_ms flag from sbp2.  Now the upper layers
will try MODE SENSE (6) before MODE SENSE (10) on all SBP-2 devices.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

nodemgr_resume_ne was iterating over nodemgr_ud_class.children without
protection by nodemgr_ud_class.subsys.rwsem.

FIXME:
Shouldn't we rather use class->sem there, not class->subsys.rwsem?
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

nodemgr_update_pdrv grabbed an rw semaphore (as reader) which was
already taken by its caller's caller, nodemgr_probe_ne (as reader too).
Reported by Miles Lane, call path pointed out by Arjan van de Ven.

FIXME:
Shouldn't we rather use class->sem there, not class->subsys.rwsem?
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Add some pointers to SCSI to the configuration menu item of sbp2.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Scsi_remove_device() may go into uninterruptible sleep if blocked.
Therefore sbp2_remove() unblocks the Scsi_Host before the device is
requested to be removed.  But there could be another 1394 bus reset
after that which would block the host again.  The 1394 subsystem won't
call sbp2_update() concurrently to sbp2_remove(), which is why there is
no chance for sbp2_remove() to be unblocked by sbp2_update().

The fix is to tell sbp2's bus reset handler when a device is to be shut
down so that it skips scsi_block_requests() on that host.  As before,
any new commands after a reset without reconnect will be failed quickly
by sbp2scsi_queuecommand().

In the long term, means to go without scsi_block_requests() should be
found.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Remove unused includes.  Add missing includes, i.e. explicitly include
all used headers.  Sort includes alphabetically.  Replace one call to
signal_pending(current) to avoid to include headers just for this line.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

If the target signals a transport failure via status block, complete the
request with DID_BUSY to indicate to the SCSI subsystem that the command
may succeed when retried.

Also log diagnostic information if the status block shows a transport
related problem.  It may point to hardware faults.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

While sbp2_update() is doing its duties after a bus reset, another reset
could happen.  Don't accept new requests until the next undisturbed
sbp2_update() or until sbp2_remove().
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

The scsi_host_template's eh_abort_handler and eh_device_reset_handler
are allowed to sleep.  Use this to run sbp2_agent_reset in the more
reliable mode which returns _after_ its write transaction was finished.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Fix for http://bugzilla.kernel.org/show_bug.cgi?id=6948

Because sbp2 writes to the target's fetch agent's registers from within
atomic context, it cannot sleep to guaranteedly get a free transaction
label.  This may repeatedly lead to "sbp2util_node_write_no_wait failed"
and consequently to SCSI command abortion after timeout.  A likely cause
is that many queue_command softirqs may occur before khpsbpkt (the
ieee1394 driver's thread which cleans up after finished transactions) is
woken up to recycle tlabels.

Sbp2 now schedules a workqueue job whenever sbp2_link_orb_command fails
in sbp2util_node_write_no_wait.  The job will reliably get a transaction
label because it can sleep.

We use the kernel-wide shared workqueue because it is unlikely that the
job itself actually needs to sleep.  In the improbable case that it has
to sleep, it doesn't need to sleep long since the standard transaction
timeout is 100ms.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Remove some code which is unneeded if CONFIG_PM=n.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

A deactivated macro, defined as "#define foo(bar)", will result in
silent corruption if somebody forgets a semicolon after a call to foo.
Replace it by "#define foo(bar) do {} while (0)" which will reveal any
respective syntax errors.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

This patch adds support for the poll file operation to the video1394
driver.
Signed-off-by: David Moore <dcm@acm.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

This patch contains the scheduled removal of the force_inquiry_hack
module parameter.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

This makes debugging with firescope easier.

Signed-off-by: Andi Kleen <ak@suse.de> (original patch)

Update:
 - no need for #ifdef MODULE
 - add comment in ieee1394_core, more verbose comment in ohci1394

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (update)

The waitqueue API is used to replace a custom wait mechanism.  Only one
global waitqueue (instead of per-device waitqueues or completions) is
added because there is usually just one waiter.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

 - Add checks for the (very unlikely) cases that the target writes too
   little or too much status data or writes unsolicited status.
 - Indicate that these and similar conditions are unlikely().
 - Check the 'resp' and 'sbp_status' fields for possible failure status.
 - Slightly optimize access macros for the status block bitfields.
 - Unify a few related log messages.

TODO:  Check if 'src'==1, then withhold the respective ORB from reuse
until status for any subsequent ORB was received.  This is an old bug
whose fix requires more complex command queue handling.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Sbp2's copy of the status fifo was cleared when management ORBs or new
command ORBs were prepared.  The latter had potential for a race
condition if the block layer's soft IRQ and the 1394 LLD's interrupt
handler ran on different CPUs.  It would also yield wrong status if a
command was completed with non-zero completion status before other
commands that had zero completion status, and no new command was
enqueued in the meantime.

Now, the status buffer is cleared right before it is written.  Thus it
ends up in the following simpler and safer access pattern:
 - sbp2_alloc_device: allocates and implicitly clears once,
 - sbp2_handle_status_write: clears, writes, and reads,
 - sbp2_query_logins, sbp2_login_device, sbp2_reconnect_device: read.
The latter three do not race with sbp2_handle_status_write because of
how the protocol works.

As a tiny optimization, the first two quadlets of the status never need
to be cleared.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Only the driver writes ORBs, the device just reads them.  Therefore
PCI_DMA_BIDIRECTIONAL can be replaced by PCI_DMA_TODEVICE which may be
cheaper on some architectures.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Since sbp2 is at the moment unable to do anything with the return value
of sbp2_link_orb_command, just discard it.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

The sbp2 initiator has two ways to tell a target's fetch agent about new
command ORBs:
 - Write the ORB's address to the ORB_POINTER register.  This must not
   be done while the fetch agent is active.
 - Put the ORB's address into the previously submitted ORB's next_ORB
   field and write to the DOORBELL register.  This may be done while the
   fetch agent is active or suspended.  It must not be done while the
   fetch agent is in reset state.
Sbp2 has a last_orb pointer which indicates in what way a new command
should be announced.  That pointer is concurrently accessed at various
occasions.  Furthermore, initiator and target are accessing the next_ORB
field of ORBs concurrently and asynchronously.

This patch does:
 - Protect all initiator accesses to last_orb by sbp2_command_orb_lock.
 - Add pci_dma_sync_single_for_device before a previously submitted
   ORB's next_ORB field is overwritten.
 - Insert a memory barrier between when next_ORB_lo and next_ORB_hi are
   overwritten.  Next_ORB_hi must not be updated before next_ORB_lo.
 - Remove the rather unspecific and now superfluous qualifier "volatile"
   from the next_ORB fields.
 - Add comments on how last_orb is connected with what is known about
   the target's fetch agent's state.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

These includes in ieee1394_core and eth1394 are obsolete.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

This patch reduces the size of struct hpsb_host and also removes
semaphores from ieee1394_transactions.c.  On i386, struct hpsb_host
shrinks from 10656 bytes to 6688 bytes.  This is accomplished by
 - using a single wait_queue for hpsb_get_tlabel instead of many
   instances of semaphores,
 - using a single lock to serialize access to all tlabel pools (the
   protected code regions are small, i.e. lock contention very low),
 - omitting the sysfs attribute tlabels_allocations.

Drawback:  In the rare case that a process needs to sleep because all
transaction labels for the node are temporarily exhausted, it is also
woken up if a tlabel for a different node became free, checks for an
available tlabel, and is put to sleep again.  The check is not costly
and the situation occurs extremely rarely.  (Tlabels are typically
only exhausted if there was no context switch to the khpsbpkt thread
which recycles tlables.)  Therefore the benefit of reduced tpool size
outweighs this drawback.

The sysfs attributes tlabels_free and tlabels_mask are not compiled
anymore unless CONFIG_IEEE1394_VERBOSEDEBUG is set.

The by far biggest member of struct hpsb_host, the struct csr_control
csr (5272 bytes on i386), is now placed at the end of struct hpsb_host.

Note, hpsb_get_tlabel calls the macro wait_event_interruptible with a
condition argument which has a side effect (allocation of a tlabel and
manipulation of the packet).  This side effect happens only if the
condition is true.  The patch relies on wait_event_interruptible not
evaluating the condition again after it became true.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Conflicts: drivers/ieee1394/hosts.c
Patch "lockdep: annotate ieee1394 skb-queue-head locking" was meddling
with patch "ieee1394: fix kerneldoc of hpsb_alloc_host".
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

[PATCH 9/9] s390: qeth driver fixes [6/6]

From: Frank Pavlic <fpavlic@de.ibm.com>
	- Hipersockets has no IPV6 support, thus prevent issueing
	  SETRTG_IPV6 control commands on Hipersockets devices.
	- fixed error handling in qeth_sysfs_(un)register
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

[PATCH 8/9] s390: qeth driver fixes [5/6]

From: Frank Pavlic <fpavlic@de.ibm.com>
	fix kernel panic in qdio queue handling.
	qeth_qdio_clear_card() could be invoked by 2 CPUs
	simultaneously (for example reboot event and recovery).
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

[PATCH 7/9] s390: qeth driver fixes [4/6]

From: Frank Pavlic <fpavlic@de.ibm.com>
	- fix kernel crash due to race,
	  set card->state to SOFTSETUP after
	  card and card->dev are initialized properly.
	- remove CONFIG_QETH_PERF_STATS, use sysfs attribute instead,
	  as we want to have the ability to turn on/off the
	  statistics at runtime.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

[PATCH 6/9] s390: qeth driver fixes [3/6]

From: Frank Pavlic <fpavlic@de.ibm.com>
       	fixed kernel panic caused by qeth driver:
        Using a bonding device qeth driver will realloc
        headroom for every skb coming from the bond device.
        Once this happens qeth frees the original skb and
        set the skb pointer to the new realloced skb.
        Under heavy transmit workload (e.g.UDP streams) through bond
        network device the qdio output queue might get full.
        In this case we return with EBUSY from qeth_send_packet.
        Returning to qeth_hard_start_xmit routine
        the skb address on the stack still points to the old address,
        which has been freed before.
        Returning from qeth_hard_start_xmit with EBUSY results in
        requeuing the skb. In this case it corrupts the qdisc queue
        and results in kernel panic.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

[PATCH 5/9] s390: qeth driver fixes [2/6]

From: Frank Pavlic <fpavlic@de.ibm.com>
	- fixed error handling in create_device_attributes
	- fixed some minor bugs in IPv4
	  and IPv6 address checking
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

[PATCH 4/9] s390: qeth driver fixes [1/6]

From: Frank Pavlic <fpavlic@de.ibm.com>
	- Drop incoming packets with vlan_tag set
          if card->vlangrp is not set.
        - use always vlan_hwaccel_rx to pass
	  vlan frames to the stack.
        - fix recovery problem. Device was recovered
	  properly but still not working.
	  netif_carrier_on call right before
          recovery start fixes it.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

[PATCH 3/9] s390: Makefile cleanup

From: Frank Pavlic <fpavlic@de.ibm.com>
 	remove CONFIG_MPC from Makefile which was
	introduced accidently in the past.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

[PATCH 2/9] s390: netiucv driver fixes

From: Frank Pavlic <fpavlic@de.ibm.com>
	- missing lock initialization added
        - avoid duplicate iucv-interfaces to the same peer
       	- rw-lock added for manipulating the list of
          defined iucv connections
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Hi Jeff,
this is a RESEND of the nine s390 network driver patches.
I finally found  that my kmail corrupted almost every patch
I sent the last time. Please apply these 9 patches and forget
about my first attempt! Sorry for the delay, I had some fights
with sendmail, IMAP and mutt configuration.

Frank

[RESEND PATCH 1/9] s390: minor s390 network driver fixes

From: Frank Pavlic <fpavlic@de.ibm.com>
	- iucv driver:
          use do { } while (0) constructs
	  instead of empty defines to avoid compile bugs.
        - ctc driver:
          missing lock initialization added
        - lcs driver:
          BUG_ON usage was removed accidently
	  with the last lcs patch.
          Put them back in place.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>