There was a bug reported on RHEL5 that a 10G dd on a 12G box
had a very, very slow sync after that.

At issue was the loop in write_cache_pages scanning all the way
to the end of the 10G file, even though the subsequent call
to mpage_da_submit_io would only actually write a smallish amt; then
we went back to the write_cache_pages loop ... wasting tons of time
in calling __mpage_da_writepage for thousands of pages we would
just revisit (many times) later.

Upstream it's not such a big issue for sys_sync because we get
to the loop with a much smaller nr_to_write, which limits the loop.

However, talking with Aneesh he realized that fsync upstream still
gets here with a very large nr_to_write and we face the same problem.

This patch makes mpage_add_bh_to_extent stop the loop after we've
accumulated 2048 pages, by setting mpd->io_done = 1; which ultimately
causes the write_cache_pages loop to break.

Repeating the test with a dirty_ratio of 80 (to leave something for
fsync to do), I don't see huge IO performance gains, but the reduction
in cpu usage is striking: 80% usage with stock, and 2% with the
below patch.  Instrumenting the loop in write_cache_pages clearly
shows that we are wasting time here.

Eventually we need to change mpage_da_map_pages() also submit its I/O
to the block layer, subsuming mpage_da_submit_io(), and then change it
call ext4_get_blocks() multiple times.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>

Turn off issuance of discard requests if the device does
not support it - similar to the action we take for barriers.
This will save a little computation time if a non-discardable
device is mounted with -o discard, and also makes it obvious
that it's not doing what was asked at mount time ...
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>

ext4_freeze() used jbd2_journal_lock_updates() which takes
the j_barrier mutex, and then returns to userspace.  The
kernel does not like this:

================================================
[ BUG: lock held when returning to user space! ]
------------------------------------------------
lvcreate/1075 is leaving the kernel with locks still held!
1 lock held by lvcreate/1075:
 #0:  (&journal->j_barrier){+.+...}, at: [<ffffffff811c6214>]
jbd2_journal_lock_updates+0xe1/0xf0

Use vfs_check_frozen() added to ext4_journal_start_sb() and
ext4_force_commit() instead.

Addresses-Red-Hat-Bugzilla: #568503
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>

generic setattr implementation is no longer responsible for
quota transfer so synlinks must be handled via ext4_setattr.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>

If groups_per_flex < 2, sbi->s_flex_groups[] doesn't get filled out,
and every other access to this first tests s_log_groups_per_flex;
same thing needs to happen in resize or we'll wander off into
a null pointer when doing an online resize of the file system.

Thanks to Christoph Biedl, who came up with the trivial testcase:

# truncate --size 128M fsfile
# mkfs.ext3 -F fsfile
# tune2fs -O extents,uninit_bg,dir_index,flex_bg,huge_file,dir_nlink,extra_isize fsfile
# e2fsck -yDf -C0 fsfile
# truncate --size 132M fsfile
# losetup /dev/loop0 fsfile
# mount /dev/loop0 mnt
# resize2fs -p /dev/loop0

	https://bugzilla.kernel.org/show_bug.cgi?id=13549Reported-by: Alessandro Polverini <alex@nibbles.it>
Test-case-by: Christoph Biedl  <bugzilla.kernel.bpeb@manchmal.in-ulm.de>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>

allocated_meta_data is already included in 'used' variable.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>

I have an x86_64 kernel with i386 userspace. e4defrag fails on the
EXT4_IOC_MOVE_EXT ioctl because it is not wired up for the compat
case. It seems that struct move_extent is compat save, only types
with fixed widths are used:
{
        __u32 reserved;         /* should be zero */
        __u32 donor_fd;         /* donor file descriptor */
        __u64 orig_start;       /* logical start offset in block for orig */
        __u64 donor_start;      /* logical start offset in block for donor */
        __u64 len;              /* block length to be moved */
        __u64 moved_len;        /* moved block length */
};

Lets just wire up EXT4_IOC_MOVE_EXT for the compat case.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
CC: Akira Fujita <a-fujita@rs.jp.nec.com> 

This function cleans up after ext4_mb_load_buddy(), so the renaming
makes the code clearer.
Signed-off-by: Jing Zhang <zj.barak@gmail.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>

Signed-off-by: Jing Zhang <zj.barak@gmail.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>

When EIO occurs after bio is submitted, there is no memory free
operation for bio, which results in memory leakage. And there is also
no check against bio_alloc() for bio.
Acked-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Jing Zhang <zj.barak@gmail.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>

Making sure ee_block is initialized to zero to prevent gcc from
kvetching.  It's harmless (although it's not obvious that it's
harmless) from code inspection:

fs/ext4/move_extent.c:478: warning: 'start_ext.ee_block' may be used
uninitialized in this function

Thanks to Stefan Richter for first bringing this to the attention of
linux-ext4@vger.kernel.org.
Signed-off-by: LiuQi <lingjiujianke@gmail.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] Retry commands with UNIT_ATTENTION sense codes to fix ext3/ext4 I/O error
  [SCSI] Enable retries for SYNCRONIZE_CACHE commands to fix I/O error
  [SCSI] scsi_debug: virtual_gb ignores sector_size
  [SCSI] libiscsi: regression: fix header digest errors
  [SCSI] fix locking around blk_abort_request()
  [SCSI] advansys: fix narrow board error path

commit 672917dc ("cpuidle: menu governor: reduce latency on exit")
added an optimization, where the analysis on the past idle period moved
from the end of idle, to the beginning of the new idle.

Unfortunately, this optimization had a bug where it zeroed one key
variable for new use, that is needed for the analysis.  The fix is
simple, zero the variable after doing the work from the previous idle.

During the audit of the code that found this issue, another issue was
also found; the ->measured_us data structure member is never set, a
local variable is always used instead.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Corrado Zoccolo <czoccolo@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://neil.brown.name/md:
  md: restore ability of spare drives to spin down.
  md/raid6: Fix raid-6 read-error correction in degraded state

* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
  pcmcia: fix compilation after 16bit state locking changes
  pcmcia: order userspace suspend and resume requests
  pcmcia: avoid pccard_validate_cis failure in resume callpath

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  blk-cgroup: Fix an RCU warning in blkiocg_create()
  blk-cgroup: Fix RCU correctness warning in cfq_init_queue()
  drbd: don't expose failed local READ to upper layers

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/ttm: Remove the ttm_bo_block_reservation() function.
  drm/ttm: Remove some leftover debug messages.
  drm/radeon: async event synchronization for drmWaitVblank

Move initialization of the virtio framework before the initialization of
mtd, so that block2mtd can be used on virtio-based block devices.

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=15644Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
  NFS: Fix RCU issues in the NFSv4 delegation code
  NFSv4: Fix the locking in nfs_inode_reclaim_delegation()

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  ACPI: sleep: init_set_sci_en_on_resume for Dell Studio 155x
  ACPI: fix acpi_hest_firmware_first_pci() caused oops
  sbshc: acpi_device_class "smbus_host_controller" too long
  power_meter: acpi_device_class "power_meter_resource" too long
  acpi_pad: "processor_aggregator" name too long
  PNP: don't check for conflicts with bridge windows
  ACPI: DMI init_set_sci_en_on_resume for multiple Lenovo ThinkPads
  PNPACPI: compute Address Space length rather than using _LEN
  ACPI: silence kmemcheck false positive

* 'v4l_for_2.6.34' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  V4L/DVB: pxa_camera: move fifo reset direct before dma start
  V4L/DVB: video: testing unsigned for less than 0
  V4L/DVB: mx1-camera: compile fix
  V4L/DVB: budget: Oops: "BUG: unable to handle kernel NULL pointer 	dereference"
  V4L/DVB: ngene: Workaround for stuck DiSEqC pin
  V4L/DVB: saa7146: fix regression of the av7110/budget-av driver
  V4L/DVB: v4l: fix config dependencies: mxb and saa7191 are V4L2 drivers, not V4L1
  V4L/DVB: feature-removal: announce videotext.h removal
  V4L/DVB: V4L - vpfe capture - fix for kernel crash
  V4L/DVB: gspca: make usb id 0461:0815 get handled by the right driver
  V4L/DVB: gspca - stv06xx: Remove the 046d:08da from the stv06xx driver
  V4L/DVB: gspca - sn9c20x: Correct onstack wait_queue_head declaration
  V4L/DVB: saa7146: fix up bytesperline if it is an impossible value
  V4L/DVB: V4L: vpfe_capture - free ccdc_lock when memory allocation fails
  V4L/DVB: V4L - Makfile:Removed duplicate entry of davinci
  V4L/DVB: omap24xxcam: potential buffer overflow

Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  rcu: create rcu_my_thread_group_empty() wrapper
  memcg: css_id() must be called under rcu_read_lock()
  cgroup: Check task_lock in task_subsys_state()
  sched: Fix an RCU warning in print_task()
  cgroup: Fix an RCU warning in alloc_css_id()
  cgroup: Fix an RCU warning in cgroup_path()
  KEYS: Fix an RCU warning in the reading of user keys
  KEYS: Fix an RCU warning

Some time ago we stopped the clean/active metadata updates
from being written to a 'spare' device in most cases so that
it could spin down and say spun down.  Device failure/removal
etc are still recorded on spares.

However commit 51d5668c broke this 50% of the time,
depending on whether the event count is even or odd.
The change log entry said:

   This means that the alignment between 'odd/even' and
    'clean/dirty' might take a little longer to attain,

how ever the code makes no attempt to create that alignment, so it
could take arbitrarily long.

So when we find that clean/dirty is not aligned with odd/even,
force a second metadata-update immediately.  There are already cases
where a second metadata-update is needed immediately (e.g. when a
device fails during the metadata update).  We just piggy-back on that.
Reported-by: Joe Bryant <tenminjoe@yahoo.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org

Fix: Raid-6 was not trying to correct a read-error when in
singly-degraded state and was instead dropping one more device, going to
doubly-degraded state. This patch fixes this behaviour.
Tested-by: Janos Haar <janos.haar@netcenter.hu>
Signed-off-by: Gabriele A. Trombetti <g.trombetti.lkrnl1213@logicschema.com>
Reported-by: Janos Haar <janos.haar@netcenter.hu>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org

with CONFIG_PROVE_RCU=y, a warning can be triggered:

  # mount -t cgroup -o blkio xxx /mnt
  # mkdir /mnt/subgroup

...
kernel/cgroup.c:4442 invoked rcu_dereference_check() without protection!
...

To fix this, we avoid caling css_depth() here, which is a bit simpler
than the original code.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

Merge branches 'bugzilla-14337', 'bugzilla-14998', 'bugzilla-15407', 'bugzilla-15903' and 'misc-2.6.34' into release

It's unused and buggy in its current form, since it can place a bo
in the reserved state without removing it from lru lists.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Bring radeon up to speed with the async event synchronization for
drmWaitVblank. See c9a9c5e0 for
more information. Without this patch event never get delivered
to userspace client.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Move the fifo reset from pxa_camera_start_capture to pxa_camera_irq direct
before the dma start after an end of frame interrupt to prevent images from
shifting because of old data at the begin of the frame.
Signed-off-by: Stefan Herbrechtsmeier <hbmeier@hni.uni-paderborn.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

soc_mbus_bytes_per_line() returns -EINVAL on error but we store it in an
unsigned int so the test for less than zero doesn't work.  I think it
always returns "small" positive values so we can just cast it to int
here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

This fixes a regression of

	7d58289f (mx1: prefix SOC specific defines with MX1_ and deprecate old names)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Never call dvb_frontend_detach if we failed to attach a frontend. This fixes
the following oops, which will be triggered by a missing stv090x module:

[    8.172997] DVB: registering new adapter (TT-Budget S2-1600 PCI)
[    8.209018] adapter has MAC addr = 00:d0:5c:cc:a7:29
[    8.328665] Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    8.328753] Intel ICH 0000:00:1f.5: setting latency timer to 64
[    8.562047] DVB: Unable to find symbol stv090x_attach()
[    8.562117] BUG: unable to handle kernel NULL pointer dereference at 000000ac
[    8.562239] IP: [<e08b04a3>] dvb_frontend_detach+0x4/0x67 [dvb_core]

Ref http://bugs.debian.org/575207Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Send one DiSEqC byte to make sure that the pin is set to low level.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Reviewed-by: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

An earlier regression fix for the mxb driver (V4L/DVB: saa7146_vv: fix
regression where v4l2_device was registered too late) caused a new
regression in the av7110 driver.

Reverted the old fix and fixed the problem in the mxb driver instead.
Tested on mxb and budget-av cards.

The real problem is that the saa7146 framework has separate probe()
and attach() driver callbacks which should be rolled into one. This
is now done for the mxb driver, but others should do the same. Lack
of hardware makes this hard to do, though. I hope to get hold of some
hexium cards and then I can try to improve the framework to prevent
this from happening again.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

v4l: fix config dependencies: mxb and saa7191 are V4L2 drivers, not V4L1
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

As part of upstream merge, set_params() function was removed from isif.c.
This requires removal of BUG_ON() and check for set_params ptr in
vpfe_capture.c. Without this kernel crash dump is seen while bootup on DM365

Also made following changes:-

 1) converted error messages to debug messages since it is not right to flood
    the console with error messages for user mistakes.
 2) returns -EINVAL if ioctl is not supported
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>