This patch fixes ERROR:POINTER_LOCATION from checkpatch file check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

No need to cast void pointers.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch allows to switch the netns when packet is encapsulated or
decapsulated.
The vxlan socket is openned into the i/o netns, ie into the netns where
encapsulated packets are received. The socket lookup is done into this netns to
find the corresponding vxlan tunnel. After decapsulation, the packet is
injecting into the corresponding interface which may stand to another netns.

When one of the two netns is removed, the tunnel is destroyed.

Configuration example:
ip netns add netns1
ip netns exec netns1 ip link set lo up
ip link add vxlan10 type vxlan id 10 group 239.0.0.10 dev eth0 dstport 0
ip link set vxlan10 netns netns1
ip netns exec netns1 ip addr add 192.168.0.249/24 broadcast 192.168.0.255 dev vxlan10
ip netns exec netns1 ip link set vxlan10 up
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the ARRAY_SIZE macro to determine the number of entries in
bcm_enet_gstrings_stats.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/ethernet/intel/igb/e1000_mac.c
	net/core/filter.c

Both conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>

Redefine some macros that were conditioned upon SMC_DEBUG level.

By allowing compiler to verify parameters used by these macros
unconditionally, we can flag compilation failures.

Compiler will still optimize out the unused code path depending on
SMC_DEBUG, so this is a net gain.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The aggresive load balancing causes packet re-ordering as active
flows are moved from a slave to another within the group. Sometime
this aggresive lb is not necessary if the preference is for less
re-ordering. This parameter if used with value "0" disables
this dynamic flow shuffling minimizing packet re-ordering. Of course
the side effect is that it has to live with the static load balancing
that the hashing distribution provides. This impact is less severe if
the correct xmit-hashing-policy is used for the tlb setup.

The default value of the parameter is set to "1" mimicing the earlier
behavior.

Ran the netperf test with 200 stream for 1 min between two hosts with
4x1G trunk (xmit-lb mode with xmit-policy L3+4) before and after these
changes. Following was the command used for those 200 instances -

    netperf -t TCP_RR -l 60 -s 5 -H <host> -- -r81920,81920

Transactions per second:
    Before change: 1,367.11
    After  change: 1,470.65

Change-Id: Ie3f75c77282cf602e83a6e833c6eb164e72a0990
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Re-organized the xmit function for the lb mode separating tlb xmit
from the alb mode. This will enable use of the hashing policies
like 802.3ad mode. Also extended use of xmit-hash-policy to tlb mode.

Now the tlb-mode defaults to BOND_XMIT_POLICY_LAYER2 if the xmit policy
module parameter is not set (just like 802.3ad, or Xor mode).

Change-Id: I140257403d272df75f477b380207338d0f04963e
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Separating the actual xmit part from the function in a separate
function that can be used in the tlb_xmit in the next patch. Also
there is no reason do_tx_balance to be an int so changing it to
bool type.

Change-Id: I9c48ff30487810f68587e621a191db616f49bd3b
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Modified the hash function to return just hash separating from the
modulo operation that can be performed by the caller. This is to
make way for the tlb mode to use the same hashing policies that
are used in the 802.3ad and Xor mode.

Change-Id: I276609e87e0ca213c4d1b17b79c5e0b0f3d0dd6f
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Johannes noted this is not needed, all of the fragment
accessors don't need CONFIG_NET_NS. This goes test compiled with
CONFIG_BT_6LOWPAN=y and a disabled CONFIG_NET_NS.

CC: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: linux-zigbee-devel@lists.sourceforge.net
Cc: David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series contains updates to ixgbe, ixgbevf, e1000e, igb and i40e.

Jacob converts the ixgbe low_water into an array which allows the
algorithm to output different values for different TCs and we can
distinguish between them.  Removes vlan_filter_disable() and
vlan_filter_enable() in ixgbe so that we can do the work directly in
set_rx_mode().  Changes the setting of multicast filters only when
the interface is not in promiscuous mode for multicast packets in
ixgbe.  Improves MAC filter handling by adding mac_table API based
on work done for igb, which includes functions to add/delete MAC
filters.

Mark changes register reads in ixgbe to an out-of-line function since
register reads are slow.

Emil provides a ixgbevf patch to update the driver description since
it supports more than just 82599 parts now.

David provides several cleanup patches for e1000e which resolve some
checkpatch issues as well as changing occurrences of returning 0 or 1 in
bool functions to returning true false or true.

Carolyn provides several cleanup patches for igb which fix checkpatch
warnings.

Mitch provides a fix for i40evf where the driver would correctly allow
the virtual function link state to be controlled by 'ip set link', but
would not report it correctly back.  This is fixed by filling out
the appropriate field in the VF info struct.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

exisiting BPF verifier allows uninitialized access to registers,
'ret A' is considered to be a valid filter.
So initialize A and X to zero to prevent leaking kernel memory
In the future BPF verifier will be rejecting such filters
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This was caught when using a spatch (aka. coccinelle) script
written by Joe Perches.

Cc: Joe Perches <joe@perches.com>
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexey Charkov says:

====================
net: via-rhine: add support for on-chip Rhine controllers

This series introduces platform bus (OpenFirmware) binding for
via-rhine, as used in various ARM-based Systems-on-Chip by
VIA/WonderMedia.

This has been tested in OF configuration by myself on a WM8950-based VIA
APC Rock development board and on a WM8850-based netbook, and in PCI
configuration by Roger.

Please note that the initial version of these patches was signed off by
Roger, but some time has passed since then, so I'm not including his
sign-off until explicit notice.

Changes since v1:
 - Fixed indentation of function arguments
 - Switched to 'dev_is_pci' instead of string comparison on bus name
 - Dropped 'rhine,revision' DT attribute, put the revision into OF match
        table instead
 - Included actual device tree nodes where applicable
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This should make the driver usable with VIA/WonderMedia ARM-based
Systems-on-Chip integrated Rhine III adapters. Note that these
are always in MMIO mode, and don't have any known EEPROM.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use more generic data structures instead of struct pci_dev wherever
possible in preparation for OF bus binding
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove legacy PCI DMA wrappers and instead use generic DMA functions
directly in preparation for OF bus binding
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

The goal of this patch is to fix rtnelink notification. The main problem was
about notification for fdb entry with more than one remote. Before the patch,
when a remote was added to an existing fdb entry, the kernel advertised the
first remote instead of the added one. Also when a remote was removed from a fdb
entry with several remotes, the deleted remote was not advertised.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In ksz9021_load_values_from_of() val2 to val4 aren't tested against their
initialization value.
This causes the test to always succeed, and this value to be used as if it
was loaded from the devicetree instead of being ignored, in case of a
missing/invalid property in the ethernet OF device node.
As a result, the value "0" is written to the relevant registers.

Change the conditions to test against the right initialization value.
Signed-off-by: Hubert Chaumette <hchaumette@adeneo-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The recent patch that moved broadcasts to process context added
a couple of bugs on the error path where we may dereference NULL
or leak an skb.  This patch fixes them.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nicolas Dichtel says:

====================
gre: allow to switch netns during encap/decap

The goal of this serie is to add x-netns support for the module ip_gre and
ip6_gre, ie the encapsulation addresses and the network device are not owned by
the same namespace.

Example to configure an ipv4 gre tunnel:

modprobe ip_gre
ip netns add netns1
ip netns exec netns1 ip link set lo up
ip link add gre1 type gre remote 10.16.0.121 local 10.16.0.249 ikey 10 okey 10 csum
ip link set gre1 netns netns1
ip netns exec netns1 ip link set gre1 up
ip netns exec netns1 ip addr add dev gre1 192.168.0.249 remote 192.168.0.121
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch allows to switch the netns when packet is encapsulated or
decapsulated. In other word, the encapsulated packet is received in a netns,
where the lookup is done to find the tunnel. Once the tunnel is found, the
packet is decapsulated and injecting into the corresponding interface which
stands to another netns.

When one of the two netns is removed, the tunnel is destroyed.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch allows to switch the netns when packet is encapsulated or
decapsulated. In other word, the encapsulated packet is received in a netns,
where the lookup is done to find the tunnel. Once the tunnel is found, the
packet is decapsulated and injecting into the corresponding interface which
stands to another netns.

When one of the two netns is removed, the tunnel is destroyed.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The union contains only one member now, so we use the variables in it directly.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Removed recv_pkt_list and lock, and updated related code, so that
the locking overhead is reduced especially when multiple channels
are in use.

The recv_pkt_list isn't actually necessary because the packets are
processed sequentially in each channel. It has been replaced by a
local variable, and the related lock for this list is also removed.
The is_data_pkt field is not used in receive path, so its assignment
is cleaned up.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Although the driver would correctly allow the VF link state to be
controlled by 'ip set link', it would not report it correctly back.

Fix this by filling out the appropriate field in the vf info struct.

Change-ID: I58d8e356438190e1ee9660b424301af6f416cdbe
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes WARNING:LEADING_SPACE, WARNING:SPACING, ERROR:SPACING,
WARNING:SPACE_BEFORE_TAB and ERROR_CODE_INDENT from checkpatch file check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes WARNING:BRACES and ERROR:OPEN_BRACE from
checkpatch file check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes WARNING:PREFER_PR_LEVEL and WARNING:SPLIT_STRING
from checkpatch file check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fixing "WARNING:SPACING: Unnecessary space before function pointer arguments"
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fixing "WARNING:SPACING: networking uses a blank line after declarations"
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Changing occurrences of returning 0 and 1 from bool functions to false and
true, respectively
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes 82599 from the description of the ixgbevf module
since the VF driver is supported on other parts as well.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add mac_table API based on work done for igb, which includes functions
to add and delete mac filters. This simplifies code for various entities
that use MAC filters such as VMDQ, SR-IOV, MACVLAN, and such.
Reported-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In line with changes done by Alex Duyck regarding unicast filters, we
now only set multicast filters when the interface is not in promiscuous
mode for multicast packets. This also has an impact on the RAR usage
such that SR-IOV has some RARs reserved for its own usage.
Reported-by: Alex Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously these functions handled stripping setup as well, but this has
already been removed from these functions. Rather than encapsulating
this into a function, we can just do the work directly in set_rx_mode.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Register reads are slow, so don't inline them.

Size before:
   text	   data	    bss	    dec	    hex	filename
 226337	   8280	    552	 235169	  396a1	ixgbe.ko

Size after:
   text	   data	    bss	    dec	    hex	filename
 194578	   8280	    552	 203410	  31a92	ixgbe.ko

for about a 14% reduction in text size.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>