- 08 Mar, 2016 29 commits
-
-
Florian Fainelli authored
commit 50d89980 upstream. The clear and set masks in the call to phy_set_clr_bits() called from bcm7xxx_config_init() are inverted. We need to fix this by swapping the two arguments, that is, set 0 bits, but clear the shade mode 2 enable bit. Fixes: b560a58c ("net: phy: add Broadcom BCM7xxx internal PHY driver") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Rainer Weikusat authored
commit a5527dda upstream. The unix_dgram_sendmsg routine use the following test if (unlikely(unix_peer(other) != sk && unix_recvq_full(other))) { to determine if sk and other are in an n:1 association (either established via connect or by using sendto to send messages to an unrelated socket identified by address). This isn't correct as the specified address could have been bound to the sending socket itself or because this socket could have been connected to itself by the time of the unix_peer_get but disconnected before the unix_state_lock(other). In both cases, the if-block would be entered despite other == sk which might either block the sender unintentionally or lead to trying to unlock the same spin lock twice for a non-blocking send. Add a other != sk check to guard against this. Fixes: 7d267278 ("unix: avoid use-after-free in ep_remove_wait_queue") Reported-By:
Philipp Hahn <pmhahn@pmhahn.de> Signed-off-by:
Rainer Weikusat <rweikusat@mobileactivedefense.com> Tested-by:
-
Rainer Weikusat authored
commit 1b92ee3d upstream. The present unix_stream_read_generic contains various code sequences of the form err = -EDISASTER; if (<test>) goto out; This has the unfortunate side effect of possibly causing the error code to bleed through to the final out: return copied ? : err; and then to be wrongly returned if no data was copied because the caller didn't supply a data buffer, as demonstrated by the program available at http://pad.lv/1540731 Change it such that err is only set if an error condition was detected. Fixes: 3822b5c2 ("af_unix: Revert 'lock_interruptible' in stream receive code") Reported-by:
Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by:
-
Jay Vosburgh authored
commit 21a75f09 upstream. The current logic in bond_arp_rcv will accept an incoming ARP for validation if (a) the receiving slave is either "active" (which includes the currently active slave, or the current ARP slave) or, (b) there is a currently active slave, and it has received an ARP since it became active. For case (b), the receiving slave isn't the currently active slave, and is receiving the original broadcast ARP request, not an ARP reply from the target. This logic can fail if there is no currently active slave. In this situation, the ARP probe logic cycles through all slaves, assigning each in turn as the "current_arp_slave" for one arp_interval, then setting that one as "active," and sending an ARP probe from that slave. The current logic expects the ARP reply to arrive on the sending current_arp_slave, however, due to switch FDB updating delays, the reply may be directed to another slave. This can arise if the bonding slaves and switch are working, but the ARP target is not responding. When the ARP target recovers, a condition may result wherein the ARP target host replies faster than the switch can update its forwarding table, causing each ARP reply to be sent to the previous current_arp_slave. This will never pass the logic in bond_arp_rcv, as neither of the above conditions (a) or (b) are met. Some experimentation on a LAN shows ARP reply round trips in the 200 usec range, but my available switches never update their FDB in less than 4000 usec. This patch changes the logic in bond_arp_rcv to additionally accept an ARP reply for validation on any slave if there is a current ARP slave and it sent an ARP probe during the previous arp_interval. Fixes: aeea64ac ("bonding: don't trust arp requests unless active slave really works") Cc: Veaceslav Falico <vfalico@gmail.com> Cc: Andy Gospodarek <gospo@cumulusnetworks.com> Signed-off-by:
Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by:
-
Heinrich Schuchardt authored
commit 9d021c9d upstream. Downstream packages like Debian flash-kernel use /proc/device-tree/model to determine which dtb file to install. Hence each dts in the Linux kernel should provide a unique model identifier. Commit 2d0a7add ("ARM: Kirkwood: Add support for many Synology NAS devices") created the new files kirkwood-ds111.dts and kirkwood-ds112.dts using the same model identifier. This patch provides a unique model identifier for the Synology DiskStation DS112. Fixes: 2d0a7add ("ARM: Kirkwood: Add support for many Synology NAS devices") Signed-off-by:
Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
-
Al Viro authored
commit c80567c8 upstream. ... into returning a positive to path_openat(), which would interpret that as "symlink had been encountered" and proceed to corrupt memory, etc. It can only happen due to a bug in some ->open() instance or in some LSM hook, etc., so we report any such event *and* make sure it doesn't trick us into further unpleasantness. Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Mikulas Patocka authored
commit b6853f78 upstream. The delete opration can allocate additional space on the HPFS filesystem due to btree split. The HPFS driver checks in advance if there is available space, so that it won't corrupt the btree if we run out of space during splitting. If there is not enough available space, the HPFS driver attempted to truncate the file, but this results in a deadlock since the commit 7dd29d8d ("HPFS: Introduce a global mutex and lock it on every callback from VFS"). This patch removes the code that tries to truncate the file and -ENOSPC is returned instead. If the user hits -ENOSPC on delete, he should try to delete other files (that are stored in a leaf btree node), so that the delete operation will make some space for deleting the file stored in non-leaf btree node. Reported-by:
Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz> Signed-off-by:
-
Takashi Iwai authored
commit f883982d upstream. HP EliteBook 755 G2 with ALC3228 (ALC280) codec [103c:221c] requires the known fixup (ALC269_FIXUP_HEADSET_MIC) for making the headset mic working. Also, it suffers from the loopback noise problem, so we should disable aamix path as well. Reported-by:
Derick Eddington <derick.eddington@gmail.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
-
Mike Krinkin authored
commit 17e4bce0 upstream. Ubsan reports the following warning due to a typo in update_accessed_dirty_bits template, the patch fixes the typo: [ 168.791851] ================================================================================ [ 168.791862] UBSAN: Undefined behaviour in arch/x86/kvm/paging_tmpl.h:252:15 [ 168.791866] index 4 is out of range for type 'u64 [4]' [ 168.791871] CPU: 0 PID: 2950 Comm: qemu-system-x86 Tainted: G O L 4.5.0-rc5-next-20160222 #7 [ 168.791873] Hardware name: LENOVO 23205NG/23205NG, BIOS G2ET95WW (2.55 ) 07/09/2013 [ 168.791876] 0000000000000000 ffff8801cfcaf208 ffffffff81c9f780 0000000041b58ab3 [ 168.791882] ffffffff82eb2cc1 ffffffff81c9f6b4 ffff8801cfcaf230 ffff8801cfcaf1e0 [ 168.791886] 0000000000000004 0000000000000001 0000000000000000 ffffffffa1981600 [ 168.791891] Call Trace: [ 168.791899] [<ffffffff81c9f780>] dump_stack+0xcc/0x12c [ 168.791904] [<ffffffff81c9f6b4>] ? _atomic_dec_and_lock+0xc4/0xc4 [ 168.791910] [<ffffffff81da9e81>] ubsan_epilogue+0xd/0x8a [ 168.791914] [<ffffffff81daafa2>] __ubsan_handle_out_of_bounds+0x15c/0x1a3 [ 168.791918] [<ffffffff81daae46>] ? __ubsan_handle_shift_out_of_bounds+0x2bd/0x2bd [ 168.791922] [<ffffffff811287ef>] ? get_user_pages_fast+0x2bf/0x360 [ 168.791954] [<ffffffffa1794050>] ? kvm_largepages_enabled+0x30/0x30 [kvm] [ 168.791958] [<ffffffff81128530>] ? __get_user_pages_fast+0x360/0x360 [ 168.791987] [<ffffffffa181b818>] paging64_walk_addr_generic+0x1b28/0x2600 [kvm] [ 168.792014] [<ffffffffa1819cf0>] ? init_kvm_mmu+0x1100/0x1100 [kvm] [ 168.792019] [<ffffffff8129e350>] ? debug_check_no_locks_freed+0x350/0x350 [ 168.792044] [<ffffffffa1819cf0>] ? init_kvm_mmu+0x1100/0x1100 [kvm] [ 168.792076] [<ffffffffa181c36d>] paging64_gva_to_gpa+0x7d/0x110 [kvm] [ 168.792121] [<ffffffffa181c2f0>] ? paging64_walk_addr_generic+0x2600/0x2600 [kvm] [ 168.792130] [<ffffffff812e848b>] ? debug_lockdep_rcu_enabled+0x7b/0x90 [ 168.792178] [<ffffffffa17d9a4a>] emulator_read_write_onepage+0x27a/0x1150 [kvm] [ 168.792208] [<ffffffffa1794d44>] ? __kvm_read_guest_page+0x54/0x70 [kvm] [ 168.792234] [<ffffffffa17d97d0>] ? kvm_task_switch+0x160/0x160 [kvm] [ 168.792238] [<ffffffff812e848b>] ? debug_lockdep_rcu_enabled+0x7b/0x90 [ 168.792263] [<ffffffffa17daa07>] emulator_read_write+0xe7/0x6d0 [kvm] [ 168.792290] [<ffffffffa183b620>] ? em_cr_write+0x230/0x230 [kvm] [ 168.792314] [<ffffffffa17db005>] emulator_write_emulated+0x15/0x20 [kvm] [ 168.792340] [<ffffffffa18465f8>] segmented_write+0xf8/0x130 [kvm] [ 168.792367] [<ffffffffa1846500>] ? em_lgdt+0x20/0x20 [kvm] [ 168.792374] [<ffffffffa14db512>] ? vmx_read_guest_seg_ar+0x42/0x1e0 [kvm_intel] [ 168.792400] [<ffffffffa1846d82>] writeback+0x3f2/0x700 [kvm] [ 168.792424] [<ffffffffa1846990>] ? em_sidt+0xa0/0xa0 [kvm] [ 168.792449] [<ffffffffa185554d>] ? x86_decode_insn+0x1b3d/0x4f70 [kvm] [ 168.792474] [<ffffffffa1859032>] x86_emulate_insn+0x572/0x3010 [kvm] [ 168.792499] [<ffffffffa17e71dd>] x86_emulate_instruction+0x3bd/0x2110 [kvm] [ 168.792524] [<ffffffffa17e6e20>] ? reexecute_instruction.part.110+0x2e0/0x2e0 [kvm] [ 168.792532] [<ffffffffa14e9a81>] handle_ept_misconfig+0x61/0x460 [kvm_intel] [ 168.792539] [<ffffffffa14e9a20>] ? handle_pause+0x450/0x450 [kvm_intel] [ 168.792546] [<ffffffffa15130ea>] vmx_handle_exit+0xd6a/0x1ad0 [kvm_intel] [ 168.792572] [<ffffffffa17f6a6c>] ? kvm_arch_vcpu_ioctl_run+0xbdc/0x6090 [kvm] [ 168.792597] [<ffffffffa17f6bcd>] kvm_arch_vcpu_ioctl_run+0xd3d/0x6090 [kvm] [ 168.792621] [<ffffffffa17f6a6c>] ? kvm_arch_vcpu_ioctl_run+0xbdc/0x6090 [kvm] [ 168.792627] [<ffffffff8293b530>] ? __ww_mutex_lock_interruptible+0x1630/0x1630 [ 168.792651] [<ffffffffa17f5e90>] ? kvm_arch_vcpu_runnable+0x4f0/0x4f0 [kvm] [ 168.792656] [<ffffffff811eeb30>] ? preempt_notifier_unregister+0x190/0x190 [ 168.792681] [<ffffffffa17e0447>] ? kvm_arch_vcpu_load+0x127/0x650 [kvm] [ 168.792704] [<ffffffffa178e9a3>] kvm_vcpu_ioctl+0x553/0xda0 [kvm] [ 168.792727] [<ffffffffa178e450>] ? vcpu_put+0x40/0x40 [kvm] [ 168.792732] [<ffffffff8129e350>] ? debug_check_no_locks_freed+0x350/0x350 [ 168.792735] [<ffffffff82946087>] ? _raw_spin_unlock+0x27/0x40 [ 168.792740] [<ffffffff8163a943>] ? handle_mm_fault+0x1673/0x2e40 [ 168.792744] [<ffffffff8129daa8>] ? trace_hardirqs_on_caller+0x478/0x6c0 [ 168.792747] [<ffffffff8129dcfd>] ? trace_hardirqs_on+0xd/0x10 [ 168.792751] [<ffffffff812e848b>] ? debug_lockdep_rcu_enabled+0x7b/0x90 [ 168.792756] [<ffffffff81725a80>] do_vfs_ioctl+0x1b0/0x12b0 [ 168.792759] [<ffffffff817258d0>] ? ioctl_preallocate+0x210/0x210 [ 168.792763] [<ffffffff8174aef3>] ? __fget+0x273/0x4a0 [ 168.792766] [<ffffffff8174acd0>] ? __fget+0x50/0x4a0 [ 168.792770] [<ffffffff8174b1f6>] ? __fget_light+0x96/0x2b0 [ 168.792773] [<ffffffff81726bf9>] SyS_ioctl+0x79/0x90 [ 168.792777] [<ffffffff82946880>] entry_SYSCALL_64_fastpath+0x23/0xc1 [ 168.792780] ================================================================================ Signed-off-by:
Mike Krinkin <krinkin.m.u@gmail.com> Reviewed-by:
Xiao Guangrong <guangrong.xiao@linux.intel.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
-
Kai-Heng Feng authored
commit 3b43b71f upstream. After login to the desktop on Dell Inspiron 3162, there's a very loud background noise comes from the builtin speaker. The noise does not go away even if the speaker is muted. The noise disappears after using the aamix fixup. Codec: Realtek ALC3234 Address: 0 AFG Function Id: 0x1 (unsol 1) Vendor Id: 0x10ec0255 Subsystem Id: 0x10280725 Revision Id: 0x100002 No Modem Function Group found BugLink: http://bugs.launchpad.net/bugs/1549620Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by:
-
Ilya Dryomov authored
commit e7a88e82 upstream. The contract between try_read() and try_write() is that when called each processes as much data as possible. When instructed by osd_client to skip a message, try_read() is violating this contract by returning after receiving and discarding a single message instead of checking for more. try_write() then gets a chance to write out more requests, generating more replies/skips for try_read() to handle, forcing the messenger into a starvation loop. Reported-by:
Varada Kari <Varada.Kari@sandisk.com> Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Tested-by:
Alex Elder <elder@linaro.org> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit d045437a upstream. The ftrace:function event is only displayed for parsing the function tracer data. It is not used to enable function tracing, and does not include an "enable" file in its event directory. Originally, this event was kept separate from other events because it did not have a ->reg parameter. But perf added a "reg" parameter for its use which caused issues, because it made the event available to functions where it was not compatible for. Commit 9b63776f "tracing: Do not enable function event with enable" added a TRACE_EVENT_FL_IGNORE_ENABLE flag that prevented the function event from being enabled by normal trace events. But this commit missed keeping the function event from being displayed by the "available_events" directory, which is used to show what events can be enabled by set_event. One documented way to enable all events is to: cat available_events > set_event But because the function event is displayed in the available_events, this now causes an INVALID error: cat: write error: Invalid argument Reported-by:
Chunyu Hu <chuhu@redhat.com> Fixes: 9b63776f "tracing: Do not enable function event with enable" Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Christian Borntraeger authored
commit d7444794 upstream. In async_pf we try to allocate with NOWAIT to get an element quickly or fail. This code also handle failures gracefully. Lets silence potential page allocation failures under load. qemu-system-s39: page allocation failure: order:0,mode:0x2200000 [...] Call Trace: ([<00000000001146b8>] show_trace+0xf8/0x148) [<000000000011476a>] show_stack+0x62/0xe8 [<00000000004a36b8>] dump_stack+0x70/0x98 [<0000000000272c3a>] warn_alloc_failed+0xd2/0x148 [<000000000027709e>] __alloc_pages_nodemask+0x94e/0xb38 [<00000000002cd36a>] new_slab+0x382/0x400 [<00000000002cf7ac>] ___slab_alloc.constprop.30+0x2dc/0x378 [<00000000002d03d0>] kmem_cache_alloc+0x160/0x1d0 [<0000000000133db4>] kvm_setup_async_pf+0x6c/0x198 [<000000000013dee8>] kvm_arch_vcpu_ioctl_run+0xd48/0xd58 [<000000000012fcaa>] kvm_vcpu_ioctl+0x372/0x690 [<00000000002f66f6>] do_vfs_ioctl+0x3be/0x510 [<00000000002f68ec>] SyS_ioctl+0xa4/0xb8 [<0000000000781c5e>] system_call+0xd6/0x264 [<000003ffa24fa06a>] 0x3ffa24fa06a Signed-off-by:
Christian Borntraeger <borntraeger@de.ibm.com> Reviewed-by:
Dominik Dingel <dingel@linux.vnet.ibm.com> Signed-off-by:
-
Stefan Hajnoczi authored
commit b7052cd7 upstream. The qword_get() function NUL-terminates its output buffer. If the input string is in hex format \xXXXX... and the same length as the output buffer, there is an off-by-one: int qword_get(char **bpp, char *dest, int bufsize) { ... while (len < bufsize) { ... *dest++ = (h << 4) | l; len++; } ... *dest = '\0'; return len; } This patch ensures the NUL terminator doesn't fall outside the output buffer. Signed-off-by:
Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Alex Deucher authored
commit 39d42750 upstream. set_power_state defaults to no displays, so we need to update the display configuration after setting up the powerstate on the first call. In most cases this is not an issue since ends up getting called multiple times at any given modeset and the proper order is achieved in the display changed handling at the top of the function. Reviewed-by:
Christian König <christian.koenig@amd.com> Acked-by:
Jordan Lazare <Jordan.Lazare@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Gerhard Uttenthaler authored
commit 90cfde46 upstream. This patch fixes the problem that more CAN messages could be sent to the interface as could be send on the CAN bus. This was more likely for slow baud rates. The sleeping _start_xmit was woken up in the _write_bulk_callback. Under heavy TX load this produced another bulk transfer without checking the free_slots variable and hence caused the overflow in the interface. Signed-off-by:
Gerhard Uttenthaler <uttenthaler@ems-wuensche.com> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Lisa Du authored
commit 7a64cd88 upstream. There's one point was missed in the patch commit da49889d ("staging: binder: Support concurrent 32 bit and 64 bit processes."). When configure BINDER_IPC_32BIT, the size of binder_uintptr_t was 32bits, but size of void * is 64bit on 64bit system. Correct it here. Signed-off-by:
Lisa Du <cldu@marvell.com> Signed-off-by:
Nicolas Boichat <drinkcat@chromium.org> Fixes: da49889d ("staging: binder: Support concurrent 32 bit and 64 bit processes.") Acked-by:
Olof Johansson <olof@lixom.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [ luis: backported to 3.16: - binder is still in staging in the 3.16 kernel] Signed-off-by:
-
Peter Rosin authored
commit acc14694 upstream. Make the divisor signed as DIV_ROUND_CLOSEST is undefined for negative dividends when the divisor is unsigned. Signed-off-by:
Peter Rosin <peda@axentia.se> Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Bjørn Mork authored
commit d061c1ca upstream. Thomas reports: T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=05c6 ProdID=6001 Rev=00.00 S: Manufacturer=USB Modem S: Product=USB Modem S: SerialNumber=1234567890ABCDEF C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage Reported-by:
Thomas Schäfer <tschaefer@t-online.de> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Ken Lin authored
commit 6627ae19 upstream. Add USB ID for cp2104/5 devices on GE B650v3 and B850v3 boards. Signed-off-by:
Ken Lin <ken.lin@advantech.com.tw> Signed-off-by:
Akshay Bhat <akshay.bhat@timesys.com> Signed-off-by:
-
Andrey Skvortsov authored
commit 3158a8d4 upstream. $ lsusb: Bus 001 Device 101: ID 1e0e:9001 Qualcomm / Option $ usb-devices: T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=101 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 2 P: Vendor=1e0e ProdID=9001 Rev= 2.32 S: Manufacturer=SimTech, Incorporated S: Product=SimTech, Incorporated S: SerialNumber=0123456789ABCDEF C:* #Ifs= 7 Cfg#= 1 Atr=80 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) The last interface (6) is used for Android Composite ADB interface. Serial port layout: 0: QCDM/DIAG 1: NMEA 2: AT 3: AT/PPP 4: audio Signed-off-by:
Andrey Skvortsov <andrej.skvortzov@gmail.com> Signed-off-by:
-
Benjamin Coddington authored
commit d9dfd8d7 upstream. In the case where d_add_unique() finds an appropriate alias to use it will have already incremented the reference count. An additional dget() to swap the open context's dentry is unnecessary and will leak a reference. Signed-off-by:
Benjamin Coddington <bcodding@redhat.com> Fixes: 275bb307 ("NFSv4: Move dentry instantiation into the NFSv4-...") Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
-
John Youn authored
commit c4509601 upstream. The assignement of EP transfer resources was not handled properly in the dwc3 driver. Commit aebda618 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE") previously fixed one aspect of this where resources may be exhausted with multiple calls to SET_INTERFACE. However, it introduced an issue where composite devices with multiple interfaces can be assigned the same transfer resources for different endpoints. This patch solves both issues. The assignment of transfer resources cannot perfectly follow the data book due to the fact that the controller driver does not have all knowledge of the configuration in advance. It is given this information piecemeal by the composite gadget framework after every SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook programming model in this scenario can cause errors. For two reasons: 1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple interfaces. 2) The databook does not mention doing more DEPXFERCFG for new endpoint on alt setting (8.1.6). The following simplified method is used instead: All hardware endpoints can be assigned a transfer resource and this setting will stay persistent until either a core reset or hibernation. So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for every hardware endpoint as well. We are guaranteed that there are as many transfer resources as endpoints. This patch triggers off of the calling dwc3_gadget_start_config() for EP0-out, which always happens first, and which should only happen in one of the above conditions. Fixes: aebda618 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE") Reported-by:
Ravi Babu <ravibabu@ti.com> Signed-off-by:
John Youn <johnyoun@synopsys.com> Signed-off-by:
Felipe Balbi <balbi@kernel.org> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
-
Konrad Rzeszutek Wilk authored
commit 4d8c8bd6 upstream. Occasionaly PV guests would crash with: pciback 0000:00:00.1: Xen PCI mapped GSI0 to IRQ16 BUG: unable to handle kernel paging request at 0000000d1a8c0be0 .. snip.. <ffffffff8139ce1b>] find_next_bit+0xb/0x10 [<ffffffff81387f22>] cpumask_next_and+0x22/0x40 [<ffffffff813c1ef8>] pci_device_probe+0xb8/0x120 [<ffffffff81529097>] ? driver_sysfs_add+0x77/0xa0 [<ffffffff815293e4>] driver_probe_device+0x1a4/0x2d0 [<ffffffff813c1ddd>] ? pci_match_device+0xdd/0x110 [<ffffffff81529657>] __device_attach_driver+0xa7/0xb0 [<ffffffff815295b0>] ? __driver_attach+0xa0/0xa0 [<ffffffff81527622>] bus_for_each_drv+0x62/0x90 [<ffffffff8152978d>] __device_attach+0xbd/0x110 [<ffffffff815297fb>] device_attach+0xb/0x10 [<ffffffff813b75ac>] pci_bus_add_device+0x3c/0x70 [<ffffffff813b7618>] pci_bus_add_devices+0x38/0x80 [<ffffffff813dc34e>] pcifront_scan_root+0x13e/0x1a0 [<ffffffff817a0692>] pcifront_backend_changed+0x262/0x60b [<ffffffff814644c6>] ? xenbus_gather+0xd6/0x160 [<ffffffff8120900f>] ? put_object+0x2f/0x50 [<ffffffff81465c1d>] xenbus_otherend_changed+0x9d/0xa0 [<ffffffff814678ee>] backend_changed+0xe/0x10 [<ffffffff81463a28>] xenwatch_thread+0xc8/0x190 [<ffffffff810f22f0>] ? woken_wake_function+0x10/0x10 which was the result of two things: When we call pci_scan_root_bus we would pass in 'sd' (sysdata) pointer which was an 'pcifront_sd' structure. However in the pci_device_add it expects that the 'sd' is 'struct sysdata' and sets the dev->node to what is in sd->node (offset 4): set_dev_node(&dev->dev, pcibus_to_node(bus)); __pcibus_to_node(const struct pci_bus *bus) { const struct pci_sysdata *sd = bus->sysdata; return sd->node; } However our structure was pcifront_sd which had nothing at that offset: struct pcifront_sd { int domain; /* 0 4 */ /* XXX 4 bytes hole, try to pack */ struct pcifront_device * pdev; /* 8 8 */ } That is an hole - filled with garbage as we used kmalloc instead of kzalloc (the second problem). This patch fixes the issue by: 1) Use kzalloc to initialize to a well known state. 2) Put 'struct pci_sysdata' at the start of 'pcifront_sd'. That way access to the 'node' will access the right offset. Signed-off-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Reviewed-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
-
Konrad Rzeszutek Wilk authored
commit d159457b upstream. Commit 8135cf8b (xen/pciback: Save xen_pci_op commands before processing it) broke enabling MSI-X because it would never copy the resulting vectors into the response. The number of vectors requested was being overwritten by the return value (typically zero for success). Save the number of vectors before processing the op, so the correct number of vectors are copied afterwards. Signed-off-by:
Jan Beulich <jbeulich@suse.com> Signed-off-by:
-
Konrad Rzeszutek Wilk authored
commit 8d47065f upstream. Commit 408fb0e5 (xen/pciback: Don't allow MSI-X ops if PCI_COMMAND_MEMORY is not set) prevented enabling MSI-X on passed-through virtual functions, because it checked the VF for PCI_COMMAND_MEMORY but this is not a valid bit for VFs. Instead, check the physical function for PCI_COMMAND_MEMORY. Signed-off-by:
-
Christoph Hellwig authored
commit 50ab8ec7 upstream. See http: //www.infradead.org/rpr.html X-Evolution-Source: 1451162204.2173.11@leira.trondhjem.org Content-Transfer-Encoding: 8bit Mime-Version: 1.0 We support OFFSET_MAX just fine, so don't round down below it. Also switch to using min_t to make the helper more readable. Signed-off-by:
Christoph Hellwig <hch@lst.de> Fixes: 433c9237 ("NFS: Clean up nfs_size_to_loff_t()") Signed-off-by:
-
Ben Hutchings authored
Commit a1383cd8 ("crypto: skcipher - Add crypto_skcipher_has_setkey") was incorrectly backported to the 3.2.y and 3.16.y stable branches. We need to set ablkcipher_tfm::has_setkey in the crypto_init_blkcipher_ops_async() and crypto_init_givcipher_ops() functions as well as crypto_init_ablkcipher_ops(). Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Andy Lutomirski authored
commit 3d44d51b upstream. This doesn't seem to fix a regression -- I don't think the CLAC was ever there. I double-checked in a debugger: entries through the int80 gate do not automatically clear AC. Stable maintainers: I can provide a backport to 4.3 and earlier if needed. This needs to be backported all the way to 3.10. Reported-by:
Brian Gerst <brgerst@gmail.com> Signed-off-by:
Andy Lutomirski <luto@kernel.org> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 63bcff2a ("x86, smap: Add STAC and CLAC instructions to control user space access") Link: http://lkml.kernel.org/r/b02b7e71ae54074be01fc171cbd4b72517055c0e.1456345086.git.luto@kernel.orgSigned-off-by:
Ingo Molnar <mingo@kernel.org> [ kamal: backport to 3.10 through 3.19-stable: file rename; context ] Signed-off-by:
Kamal Mostafa <kamal@canonical.com> Signed-off-by:
-
- 04 Mar, 2016 11 commits
-
-
Simon Guinot authored
commit 59ceeaaf upstream. In __request_region, if a conflict with a BUSY and MUXED resource is detected, then the caller goes to sleep and waits for the resource to be released. A pointer on the conflicting resource is kept. At wake-up this pointer is used as a parent to retry to request the region. A first problem is that this pointer might well be invalid (if for example the conflicting resource have already been freed). Another problem is that the next call to __request_region() fails to detect a remaining conflict. The previously conflicting resource is passed as a parameter and __request_region() will look for a conflict among the children of this resource and not at the resource itself. It is likely to succeed anyway, even if there is still a conflict. Instead, the parent of the conflicting resource should be passed to __request_region(). As a fix, this patch doesn't update the parent resource pointer in the case we have to wait for a muxed region right after. Reported-and-tested-by:
Vincent Pelletier <plr.vincent@gmail.com> Signed-off-by:
Simon Guinot <simon.guinot@sequanux.org> Tested-by:
Vincent Donnefort <vdonnefort@gmail.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Jan Kara authored
commit 74dae427 upstream. Competing overwrite DIO in dioread_nolock mode will just overwrite pointer to io_end in the inode. This may result in data corruption or extent conversion happening from IO completion interrupt because we don't properly set buffer_defer_completion() when unlocked DIO races with locked DIO to unwritten extent. Since unlocked DIO doesn't need io_end for anything, just avoid allocating it and corrupting pointer from inode for locked DIO. A cleaner fix would be to avoid these games with io_end pointer from the inode but that requires more intrusive changes so we leave that for later. Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Jan Kara authored
commit ed8ad838 upstream. ext4 can update bh->b_state non-atomically in _ext4_get_block() and ext4_da_get_block_prep(). Usually this is fine since bh is just a temporary storage for mapping information on stack but in some cases it can be fully living bh attached to a page. In such case non-atomic update of bh->b_state can race with an atomic update which then gets lost. Usually when we are mapping bh and thus updating bh->b_state non-atomically, nobody else touches the bh and so things work out fine but there is one case to especially worry about: ext4_finish_bio() uses BH_Uptodate_Lock on the first bh in the page to synchronize handling of PageWriteback state. So when blocksize < pagesize, we can be atomically modifying bh->b_state of a buffer that actually isn't under IO and thus can race e.g. with delalloc trying to map that buffer. The result is that we can mistakenly set / clear BH_Uptodate_Lock bit resulting in the corruption of PageWriteback state or missed unlock of BH_Uptodate_Lock. Fix the problem by always updating bh->b_state bits atomically. Reported-by:
Nikolay Borisov <kernel@kyup.com> Signed-off-by:
-
Gerd Hoffmann authored
commit 34855706 upstream. This avoids integer overflows on 32bit machines when calculating reloc_info size, as reported by Alan Cox. Cc: gnomes@lxorguk.ukuu.org.uk Signed-off-by:
Gerd Hoffmann <kraxel@redhat.com> Reviewed-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Rasmus Villemoes authored
commit bc3f5d8c upstream. We need to use post-decrement to get the pci_map_page undone also for i==0, and to avoid some very unpleasant behaviour if pci_map_page failed already at i==0. Reviewed-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by:
-
Takashi Iwai authored
commit 13d5e5d4 upstream. The commit [7f0973e9: ALSA: seq: Fix lockdep warnings due to double mutex locks] split the management of two linked lists (source and destination) into two individual calls for avoiding the AB/BA deadlock. However, this may leave the possible double deletion of one of two lists when the counterpart is being deleted concurrently. It ends up with a list corruption, as revealed by syzkaller fuzzer. This patch fixes it by checking the list emptiness and skipping the deletion and the following process. BugLink: http://lkml.kernel.org/r/CACT4Y+bay9qsrz6dQu31EcGaH9XwfW7o3oBzSQUG9fMszoh=Sg@mail.gmail.com Fixes: 7f0973e9 ('ALSA: seq: Fix lockdep warnings due to 'double mutex locks) Reported-by:
Dmitry Vyukov <dvyukov@google.com> Tested-by:
-
Arnd Bergmann authored
commit b33c8ff4 upstream. In my randconfig tests, I came across a bug that involves several components: * gcc-4.9 through at least 5.3 * CONFIG_GCOV_PROFILE_ALL enabling -fprofile-arcs for all files * CONFIG_PROFILE_ALL_BRANCHES overriding every if() * The optimized implementation of do_div() that tries to replace a library call with an division by multiplication * code in drivers/media/dvb-frontends/zl10353.c doing u32 adc_clock = 450560; /* 45.056 MHz */ if (state->config.adc_clock) adc_clock = state->config.adc_clock; do_div(value, adc_clock); In this case, gcc fails to determine whether the divisor in do_div() is __builtin_constant_p(). In particular, it concludes that __builtin_constant_p(adc_clock) is false, while __builtin_constant_p(!!adc_clock) is true. That in turn throws off the logic in do_div() that also uses __builtin_constant_p(), and instead of picking either the constant- optimized division, and the code in ilog2() that uses __builtin_constant_p() to figure out whether it knows the answer at compile time. The result is a link error from failing to find multiple symbols that should never have been called based on the __builtin_constant_p(): dvb-frontends/zl10353.c:138: undefined reference to `____ilog2_NaN' dvb-frontends/zl10353.c:138: undefined reference to `__aeabi_uldivmod' ERROR: "____ilog2_NaN" [drivers/media/dvb-frontends/zl10353.ko] undefined! ERROR: "__aeabi_uldivmod" [drivers/media/dvb-frontends/zl10353.ko] undefined! This patch avoids the problem by changing __trace_if() to check whether the condition is known at compile-time to be nonzero, rather than checking whether it is actually a constant. I see this one link error in roughly one out of 1600 randconfig builds on ARM, and the patch fixes all known instances. Link: http://lkml.kernel.org/r/1455312410-1058841-1-git-send-email-arnd@arndb.deAcked-by:
Nicolas Pitre <nico@linaro.org> Fixes: ab3c9c68 ("branch tracer, intel-iommu: fix build with CONFIG_BRANCH_TRACER=y") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit f3775549 upstream. The tracepoint infrastructure uses RCU sched protection to enable and disable tracepoints safely. There are some instances where tracepoints are used in infrastructure code (like kfree()) that get called after a CPU is going offline, and perhaps when it is coming back online but hasn't been registered yet. This can probuce the following warning: [ INFO: suspicious RCU usage. ] 4.4.0-00006-g0fe53e8-dirty #34 Tainted: G S ------------------------------- include/trace/events/kmem.h:141 suspicious rcu_dereference_check() usage! other info that might help us debug this: RCU used illegally from offline CPU! rcu_scheduler_active = 1, debug_locks = 1 no locks held by swapper/8/0. stack backtrace: CPU: 8 PID: 0 Comm: swapper/8 Tainted: G S 4.4.0-00006-g0fe53e8-dirty #34 Call Trace: [c0000005b76c78d0] [c0000000008b9540] .dump_stack+0x98/0xd4 (unreliable) [c0000005b76c7950] [c00000000010c898] .lockdep_rcu_suspicious+0x108/0x170 [c0000005b76c79e0] [c00000000029adc0] .kfree+0x390/0x440 [c0000005b76c7a80] [c000000000055f74] .destroy_context+0x44/0x100 [c0000005b76c7b00] [c0000000000934a0] .__mmdrop+0x60/0x150 [c0000005b76c7b90] [c0000000000e3ff0] .idle_task_exit+0x130/0x140 [c0000005b76c7c20] [c000000000075804] .pseries_mach_cpu_die+0x64/0x310 [c0000005b76c7cd0] [c000000000043e7c] .cpu_die+0x3c/0x60 [c0000005b76c7d40] [c0000000000188d8] .arch_cpu_idle_dead+0x28/0x40 [c0000005b76c7db0] [c000000000101e6c] .cpu_startup_entry+0x50c/0x560 [c0000005b76c7ed0] [c000000000043bd8] .start_secondary+0x328/0x360 [c0000005b76c7f90] [c000000000008a6c] start_secondary_prolog+0x10/0x14 This warning is not a false positive either. RCU is not protecting code that is being executed while the CPU is offline. Instead of playing "whack-a-mole(TM)" and adding conditional statements to the tracepoints we find that are used in this instance, simply add a cpu_online() test to the tracepoint code where the tracepoint will be ignored if the CPU is offline. Use of raw_smp_processor_id() is fine, as there should never be a case where the tracepoint code goes from running on a CPU that is online and suddenly gets migrated to a CPU that is offline. Link: http://lkml.kernel.org/r/1455387773-4245-1-git-send-email-kda@linux-powerpc.orgReported-by:
Denis Kirjanov <kda@linux-powerpc.org> Fixes: 97e1c18e ("tracing: Kernel Tracepoints") Signed-off-by:
-
Andy Shevchenko authored
commit ee1cdcda upstream. The commit 2895b2ca ("dmaengine: dw: fix cyclic transfer callbacks") re-enabled BLOCK interrupts with regard to make cyclic transfers work. However, this change becomes a regression for non-cyclic transfers as interrupt counters under stress test had been grown enormously (approximately per 4-5 bytes in the UART loop back test). Taking into consideration above enable BLOCK interrupts if and only if channel is programmed to perform cyclic transfer. Fixes: 2895b2ca ("dmaengine: dw: fix cyclic transfer callbacks") Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
Mans Rullgard <mans@mansr.com> Tested-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Takashi Iwai authored
commit d99a36f4 upstream. When multiple concurrent writes happen on the ALSA sequencer device right after the open, it may try to allocate vmalloc buffer for each write and leak some of them. It's because the presence check and the assignment of the buffer is done outside the spinlock for the pool. The fix is to move the check and the assignment into the spinlock. (The current implementation is suboptimal, as there can be multiple unnecessary vmallocs because the allocation is done before the check in the spinlock. But the pool size is already checked beforehand, so this isn't a big problem; that is, the only possible path is the multiple writes before any pool assignment, and practically seen, the current coverage should be "good enough".) The issue was triggered by syzkaller fuzzer. BugLink: http://lkml.kernel.org/r/CACT4Y+bSzazpXNvtAr=WXaL8hptqjHwqEyFA+VN2AWEx=aurkg@mail.gmail.comReported-by:
-
Takashi Iwai authored
commit 24db8bba upstream. The kernel memory allocators already report the errors when the requested allocation fails, thus we don't need to warn it again in each caller side. Signed-off-by:
-
