This adds support for the the wakeup threshold and
support for the second wakeup unit to the DT based
setup.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

st,axis-{x,y,z} can be negative to imply inverted
axis.

Apart from that the minimal and maximal threshold
may be negative.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

balloon_wrk.num_pages is __u32 and it comes from host in struct dm_balloon
where it is also __u32. We, however, use 'int' in balloon_up() and in case
we happen to receive num_pages>INT_MAX request we'll end up allocating zero
pages as 'num_pages < alloc_unit' check in alloc_balloon_pages() will pass.
Change num_pages type to unsigned int.

In real life ballooning request come with num_pages in [512, 32768] range so
this is more a future-proof/cleanup.
Reported-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

'Drivers: hv: hv_balloon: refuse to balloon below the floor' fix does not
correctly handle the case when val.freeram < num_pages as val.freeram is
__kernel_ulong_t and the 'val.freeram - num_pages' value will be a huge
positive value instead of being negative.

Usually host doesn't ask us to balloon more than val.freeram but in case
he have a memory hog started after we post the last pressure report we
can get into troubles.
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The function mei_cl_is_transitioning is just opposite
of mei_cl_is_connected. What we actually wanted to
check is if we lost connection so we can discard
the check for transition and check for 'not connected'
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace open coded check for cl->state !=/== MEI_FILE_CONNECTED
with mei_cl_is_connected function.

Note that cl->state != MEI_FILE_CONNECTED is not the same
as cl->state == MEI_FILE_DISCONNECTED
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mei_poll returned with POLLIN w/o checking whether the operation
has really completed.
remove redundant check and locking in amthif specific handler
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Most of the retries can be done within a millisecond successfully, so we
sleep 1ms before the first retry, then gradually increase the retry
interval to 2^n with max value of 2048ms. Doing so, we will have shorter
overall delay time, because most of the cases succeed within 1-2 attempts.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

... and simplify alloc_balloon_pages() interface by removing redundant
alloc_error from it.

If we happen to enter balloon_up() with balloon_wrk.num_pages = 0 we will enter
infinite 'while (!done)' loop as alloc_balloon_pages() will be always returning
0 and not setting alloc_error. We will also be sending a meaningless message to
the host on every iteration.

The 'alloc_unit == 1 && alloc_error -> num_ballooned == 0' change and
alloc_error elimination requires a special comment. We do alloc_balloon_pages()
with 2 different alloc_unit values and there are 4 different
alloc_balloon_pages() results, let's check them all.

alloc_unit = 512:
1) num_ballooned = 0, alloc_error = 0: we do 'alloc_unit=1' and retry pre- and
  post-patch.
2) num_ballooned > 0, alloc_error = 0: we check 'num_ballooned == num_pages'
  and act accordingly,  pre- and post-patch.
3) num_ballooned > 0, alloc_error > 0: we report this chunk and remain within
  the loop, no changes here.
4) num_ballooned = 0, alloc_error > 0: we do 'alloc_unit=1' and retry pre- and
  post-patch.

alloc_unit = 1:
1) num_ballooned = 0, alloc_error = 0: this can happen in two cases: when we
  passed 'num_pages=0' to alloc_balloon_pages() or when there was no space in
  bl_resp to place a single response. The second option is not possible as
  bl_resp is of PAGE_SIZE size and single response 'union dm_mem_page_range' is
  8 bytes, but the first one is (in theory, I think that Hyper-V host never
  places such requests). Pre-patch code loops forever, post-patch code sends
  a reply with more_pages = 0 and finishes.
2) num_ballooned > 0, alloc_error = 0: we ran out of space in bl_resp, we
  report partial success and remain within the loop, no changes pre- and
  post-patch.
3) num_ballooned > 0, alloc_error > 0: pre-patch code finishes, post-patch code
  does one more try and if there is no progress (we finish with
  'num_ballooned = 0') we finish. So we try a bit harder with this patch.
4) num_ballooned = 0, alloc_error > 0: both pre- and post-patch code enter
 'more_pages = 0' branch and finish.

So this patch has two real effects:
1) We reply with an empty response to 'num_pages=0' request.
2) We try a bit harder on alloc_unit=1 allocations (and reply with an empty
   tail reply in case we fail).

An empty reply should be supported by host as we were able to send it even with
pre-patch code when we were not able to allocate a single page.
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 79208c57 ("Drivers: hv: hv_balloon: Make adjustments in computing
the floor") was inacurate as it introduced a jump in our piecewiese linear
'floor' function:

At 2048MB we have:
Left limit:
104 + 2048/8 = 360
Right limit:
256 + 2048/16 = 384 (so the right value is 232)

We now have to make an adjustment at 8192 boundary:
232 + 8192/16 = 744
512 + 8192/32 = 768 (so the right value is 488)
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently we add memory in 128Mb blocks but the request from host can be
aligned differently. In such case we add a partially backed block and
when this block goes online we skip onlining pages which are not backed
(hv_online_page() callback serves this purpose). When we receive next
request for the same host add region we online pages which were not backed
before with hv_bring_pgs_online(). However, we don't check if the the block
in question was onlined and online this tail unconditionally. This is bad as
we avoid all online_pages() logic: these pages are not accounted, we don't
send notifications (and hv_balloon is not the only receiver of them),...
And, first of all, nobody asked as to online these pages. Solve the issue by
checking if the last previously backed page was onlined and onlining the tail
only in case it was.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It's not necessary any longer, since we can safely run the blocking
message handlers in vmbus_connection.work_queue now.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since the 2 fucntions can safely run in vmbus_connection.work_queue without
hang, we don't need to schedule new work items into the per-channel workqueue.

Actally we can even remove the per-channel workqueue now -- we'll do it
in the next patch.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A work item in vmbus_connection.work_queue can sleep, waiting for a new
host message (usually it is some kind of "completion" message). Currently
the new message will be handled in the same workqueue, but since work items
in the workqueue is serialized, we actually have no chance to handle
the new message if the current work item is sleeping -- as as result, the
current work item will hang forever.

K. Y. has posted the below fix to resolve the issue:
Drivers: hv: vmbus: Perform device register in the per-channel work element

Actually we can simplify the fix by directly running non-blocking message
handlers in the dispatch tasklet (inspired by K. Y.).

This patch is the fundamental change. The following 2 patches will simplify
the message offering and rescind-offering handling a lot.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Keeping drivers related to HW tracing on ARM, i.e coresight,
under "drivers/coresight" doesn't make sense when other
architectures start rolling out technologies of the same
nature.

As such creating a new "drivers/hwtracing" directory where all
drivers of the same kind can reside, reducing namespace
pollution under "drivers/".
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Knowing the state of various control register is always
useful for degging and tuning.  As such add an entry in
sysfs that expose to userspace the most important registers.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The coresight-default-sink configuration option has been
removed from the framework. As such remove it from DT and bindings.
Signed-off-by: Kaixu Xia <xiakaixu@huawei.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

>From the TMC TRM, the ETF can be configured as buffer mode, so ETF can
be a sink type.
Signed-off-by: Xia Kaixu <kaixu.xia@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Most CoreSight blocks are 64-bit ready.  As such move configuration
entries from "arch/arm/Kconfig.config" to the driver's subdirectory
and source the newly created Kconfig from architecture specific
Kconfig.debug files.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Compiling coresight drivers with a 64-bit compiler highlights a couple
of formatting issues, which are fixed by this patch.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Function "get_logical_index()" is not available on arm64.
Instead of adding the function simply using "of_get_cpu_node()" and
comparing the return value with cpu handles yields the same
result.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The code here is checking for IS_ERR() when request_mem_region() only
returns NULL on error and never an ERR_PTR.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The API allows the application to flush a host-to-FPGA stream by calling
write() with the data count set to zero. Before this patch, copy_from_user()
was called with a non-zero byte count, which possibly made it attempt to read
from unmapped user memory. Such attempts caused the driver to return -EFAULT
instead of 0, even though the desired operation went through fine.

This patch ensures the driver returns 0 on a successful flush.
Signed-off-by: Eli Billauer <eli.billauer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pci core now disables msi on probe automatically,
drop this from device-specific code.

Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Qualcomm PMIC arbiter driver already depends on ARCH_QCOM,
which could be either ARM or ARM64. New version of the PMIC
arbiter controller is available on 64 bit platforms.
Remove ARM dependency to allow driver to be build for 64 bit
platforms.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the normal return values for bool functions
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make the miscdevice accessible through the file's private_data.

Previously, this was done only when an open() file operation had been
registered. If no custom open() file operation was defined,
private_data was set to NULL.

This subtle quirk was confusing, to the point where kernel code
registered *empty* file open operations to have private_data point to
the misc device structure and avoid duplicating that logic.

And it could easily lead to bugs, where the addition or removal of a
custom open() file operation surprisingly changes the initial value of
a file's private_data structure.

To resolve this, we now place the miscdevice in the file's private_data
member unconditionally when open() is called.
Signed-off-by: Tom Van Braeckel <tomvanbraeckel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 4d8beff2.

It causes build warnings, and it's incorrect as we do write to this
structure.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'extcon-next-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-next

Chanwoo writes:

Update extcon for v4.1

This patchset include two new extcon driver and fix minor issue of extcon
driver.

Detailed description for patchset:
1. new extcon-max77843.c and extcon-usb-gpio.c extcon driver
- extcon-max77843.c driver support the MAXIM MAX77843 MUIC (Micor-USB Interface
Controller) device which handles the various external connectors such as TA/USB
/USB-HOST/JIG and so on.
- extcon-usb-gpio.c driver support the USB and USB-HOST cable detection by
using the GPIO pin which is connected to USB ID pin. This GPIO pin updates the
USB cable states.

2. Rename the filename of extcon core driver and add missing locking mechanism
- Rename the previous extcon-class driver.c as extcon.c because '-class'
postfix is not necessary word.
- extcon core driver (extcon.c) used the raw_notifier_chain. It must be
protected by locking mechanism to avoid the list changing while
extcon_update_state() is executed.

3. Fix minor issue of extcon drviers
- Fix cable name by using the capital letter instead of small letter on
extcon-max77693.c driver.
- Clean-up code of extcon-arizona.c to detect headphone cable.
- Fix the wrong return type and variable type on extcon-max77843.c.
- Fix the checkpatch warning of all extcon drivers.

Add a driver for the NAND/External Memory Controller (NEMC) on JZ4780
and later SoCs.

The primary function of this driver is to configure parameters, such
as timings, for external memory devices using data supplied in the
device tree. Devices connected to the NEMC are represented in the DT
as children of the NEMC node, the driver uses optional properties
specified in these child nodes to configure the parameters of each
bank.
Signed-off-by: Alex Smith <alex@alex-smith.me.uk>
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add device tree bindings for the NAND/External Memory Controller (NEMC)
on Ingenic JZ4780
Signed-off-by: Alex Smith <alex@alex-smith.me.uk>
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Qualcomm PMIC Arbiter version-2 changes from version-1 are:

- Some different register offsets.
- New channel register space, one per PMIC peripheral (ppid).
  All tx traffic uses these channels.
- New observer register space. All rx trafic uses this space.
- Different command format for spmi command registers.
Reviewed-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Gilad Avidov <gavidov@codeaurora.org>
Tested-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

According to spmi spec a slave powers up into startup state and then
transitions into active state. Thus, the wakeup command is not required
before calling the slave's probe. The wakeup command is only needed for
slaves that are in sleep state after receiving the sleep command.

Cc: galak@codeaurora.org
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Sagar Dharia <sdharia@codeaurora.org>
Acked-by: Josh Cartwright <joshc@eso.teric.us>
Signed-off-by: Gilad Avidov <gavidov@codeaurora.org>
Tested-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

I take over the maintainship from Voice.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Mark Brown <broonie@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Don't wait after sending request for offers to the host. This wait is
unnecessary and simply adds 5 seconds to the boot time.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The seq_printf return value, because it's frequently misused,
will eventually be converted to void.

See: commit 1f33c41c ("seq_file: Rename seq_overflow() to
     seq_has_overflowed() and make public")
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>