- 31 Jan, 2008 40 commits
-
-
Clemens Ladisch authored
The TempoTec HiFier has a somwhat different architecture; remove it from the list of cards that are known to be supported. Signed-off-by:
Clemens Ladisch <clemens@ladisch.de> Signed-off-by:
Jaroslav Kysela <perex@perex.cz>
-
Takashi Iwai authored
The available sample rates on CS5535 depend on AC97 codec chip. Set the additional hw params limit. Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Clemens Ladisch authored
Add one more indirection to the lookup of the snd_pcm_hardware structures so that we can save the space of the duplicate ones. Signed-off-by:
-
Clemens Ladisch authored
Change the oxygen_spdif_input_bits_changed() function so that clock changes on the SPDIF input are correctly detected. This means that sample rates greater than 96 kHz are now supported. Signed-off-by:
-
Clemens Ladisch authored
Fix some wrong values for the definitions of the source masks for DACS 1 and 3. Signed-off-by:
-
Clemens Ladisch authored
Actually use the template that was maybe changed by the control filter instead of the original one. Signed-off-by:
-
Clemens Ladisch authored
Instead of having model-specific fields in the common struct oxygen, put them into a private structure that is allocated together with the card structure. Signed-off-by:
-
Clemens Ladisch authored
According to the datasheets, the SPI clock cycle must be at least 200 ns for the AK4396 and the WM8785, so we cannot use the default 160 ns. Signed-off-by:
-
Clemens Ladisch authored
Allow to record with 32 kHz, 64 kHz, 88.2 kHz and 176.4 kHz with cards that have a WM8785 ADC. Signed-off-by:
-
Clemens Ladisch authored
Add symbol definitions for the various codecs and GPIO pins. Signed-off-by:
-
Clemens Ladisch authored
The MIDI bit in the MISC register is set by default and cannot be used to detect the presence of a MIDI port. Instead, add a parameter to the oxygen_pci_probe() function so that model drivers can specify this. Signed-off-by:
-
Clemens Ladisch authored
Use the DMA_PAUSE register for pausing instead of stopping DMA. Signed-off-by:
-
Clemens Ladisch authored
Replace some magic numbers with register symbols. Signed-off-by:
-
Clemens Ladisch authored
Add documentation entries for snd-oxygen and snd-virtuoso. Signed-off-by:
-
Takashi Iwai authored
Reported by Al Viro: In copy_tlv(), the size of kmalloc is wrongly calculated. Signed-off-by:
-
Takashi Iwai authored
In azx_[rirb_]get_response(), the timeout is checked at the end of the loop. It's better to be checked just after the check of the RIRB index to avoid a bogus error with a too long msleep(). Signed-off-by:
-
Takashi Iwai authored
Clean up ice1712/ice1724 codes. The board-specific data is allocated locally in each code instead of having an ungly union in struct ice1712. Also, fix coding issues in prodigy_hifi.c. Signed-off-by:
-
Andrew Paprocki authored
This patch adds additional output to the /proc codec#X info. The following pieces of information are added to the output: - Balanced, L/R swap, trigger, impedance sense pin capabilities - Vref pin capabilities - Current Vref pin widget control setting - Default configuration association, sequence, and misc bit test - EAPD/BTL bits conveying balanced mode, EAPD, and L/R swap - Power state modified to show state name as well as setting vs actual value - GPIO parameter output on Audio Function Group, including enumeration of IO pins which are indicated present (Any I and O pins are not output at this time) - Stripe and L/R swap widget capabilities - All digital converter bits: enable, validity, validity config, preemphasis, copyright, non-audio, professional, generation level, and content category - Converter stream and channel values for in/out widgets - SDI select value for in widgets - Unsolicited response widget capability tag and enabled bit - Delay widget capability value - Processing widget capability benign bit and number of coefficients - Realtek Define Registers: processing coefficient, coefficient index [Also, fixed space/tab issues and make codes a bit more readable -- Takashi] Signed-off-by:
Andrew Paprocki <andrew@ishiboo.com> Signed-off-by:
-
Clemens Ladisch authored
The default playback routing must be 0xe4, not 0xe1; the front and surround DACs were exchanged. Signed-off-by:
-
Clemens Ladisch authored
Add more symbols for registers and register fields. Signed-off-by:
-
Timur Tabi authored
Enable mmap support in the MPC8610 ASoC driver. The driver can use ALSA's default mmap functionality, it was just not enabled previously. Signed-off-by:
Timur Tabi <timur@freescale.com> Signed-off-by:
-
Jiang zhe authored
For codec conexant 5045, I found that the name of 'Capture Source Items' is different from the name of mixer. The mixer is: HDA_CODEC_VOLUME('Ext Mic Playback Volume', 0x17, 0x2, HDA_INPUT), HDA_CODEC_MUTE('Ext Mic Playback Switch', 0x17, 0x2, HDA_INPUT), But the capture source item is : static struct hda_input_mux cxt5045_capture_source = { .num_items = 2, .items = { { 'IntMic', 0x1 }, { 'LineIn', 0x2 }, } }; I think that it's better to change the name of capture_source to avoid misunderstanding. Signed-off-by:Jiang zhe <zhe.jiang@intel.com> Signed-off-by:
-
Jiang Zhe authored
The benq r55e laptop have 3 jacks on the front panel. One for HP, one for Line In and one for Mic In. This patch implemented a new model to support it. Signed-off-by:
-
Takashi Iwai authored
Added the description of the model fujitsu for Cx5045 codec chip. Signed-off-by:
-
Julian Scheel authored
Signed-off-by:
Julian Scheel <julian@jusst.de> Signed-off-by:
Konstantin Kletschke <konsti@ku-gbr.de> Signed-off-by:
-
Clemens Ladisch authored
Add proper register bit symbols for the I2S format field, and allow card models to configure the I2S format to be used for the DACs and ADCs. Signed-off-by:
-
Jaroslav Kysela authored
See ALSA bug#1846 for more details. Signed-off-by: -
Julian Scheel authored
See ALSA bug#2384 for more details. Signed-off-by:
-
Vasily Khoruzhick authored
Codec with id 11c1:1040 sitting on hda bus isn't si3054-compatible. It should be removed from patch_si3054.c id list. The detailed information http://archives.linmodems.org/26457 From: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by:
-
Takashi Iwai authored
Some machines with STAC codecs seem to have problems (e.g. no audible playback) when the delay in codec-read routine is too short. I still don't figure out which command sequence causes this problem (due to lack of test hardware), but it's known that increasing the delay fixes. So, added a stupid workaround here temporarily... Signed-off-by:
-
Andreas Degert authored
This device has io_type == 1 (Multiface) and firmware_rev > 0xa (fixes regression from changeset 5326) Signed-off-by:
Andreas Degert <ad@papyrus-gmbh.de> Signed-off-by:
-
T. H. Huth authored
This patch provides the snd-powermac sound driver with the ability to handle dead DMA transfers. If a dead DMA transfer is detected, the driver now sets up a new DMA transfer to continue with the sound output at the point where the old transfer died. This dead DMA transfer handling has become necessary with recent kernels on certain G4 PowerMacs. Please refer to the following URLs for more information: https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3126 https://bugs.launchpad.net/ubuntu/+source/linux-source-2.6.20/+bug/87652 http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=436723 The patch is based on the dead DMA transfer handling code from the old dmasound driver which can be found in the file sound/oss/dmasound/dmasound_awacs.c in the Linux source code. Signed-off-by:
T. H. Huth <th.huth@googlemail.com> Signed-off-by:
-
Randy Dunlap authored
Fix section mismatch in caiaq: these __devinit functions can be called at any time so they should not be __devinit. WARNING: vmlinux.o(.text+0x10a8dae): Section mismatch: reference to .init.text:snd_usb_caiaq_audio_init (between 'setup_card' and 'create_card') WARNING: vmlinux.o(.text+0x10a8dd6): Section mismatch: reference to .init.text:snd_usb_caiaq_midi_init (between 'setup_card' and 'create_card') Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
-
Randy Dunlap authored
Fix section mismatch in hdsp: snd_hdsp_proc_init() can be called from an ioctl at any time. WARNING: vmlinux.o(.text+0x1089bc2): Section mismatch: reference to .init.text: (between 'snd_hdsp_create_alsa_devices' and 'snd_hdsp_free') Signed-off-by:
-
Randy Dunlap authored
Fix section mismatch in atiixp by making some functions __devinit. WARNING: vmlinux.o(.text+0xfd9304): Section mismatch: reference to .init.data:atiixp_quirks (between 'ac97_probing_bugs' and 'snd_atiixp_codec_detect') Signed-off-by:
-
Randy Dunlap authored
Fix section mismatch in ad1889 by renaming the pci_driver variable to a whitelisted variable name. WARNING: vmlinux.o(.data+0x2e5ff0): Section mismatch: reference to .init.text:snd_ad1889_probe (between 'ad1889_pci' and 'index') Signed-off-by:
-
Randy Dunlap authored
Fix section mismatches in mts64 by making a static variable __devinitdata. WARNING: vmlinux.o(.data+0x2e33f0): Section mismatch: reference to .init.data:mts64_ctl_smpte_switch (between 'control.19929' and 'snd_mts64_rawmidi_output_ops') WARNING: vmlinux.o(.data+0x2e33f8): Section mismatch: reference to .init.data:mts64_ctl_smpte_time_hours (between 'control.19929' and 'snd_mts64_rawmidi_output_ops') WARNING: vmlinux.o(.data+0x2e3400): Section mismatch: reference to .init.data:mts64_ctl_smpte_time_minutes (between 'control.19929' and 'snd_mts64_rawmidi_output_ops') WARNING: vmlinux.o(.data+0x2e3408): Section mismatch: reference to .init.data:mts64_ctl_smpte_time_seconds (between 'control.19929' and 'snd_mts64_rawmidi_output_ops') WARNING: vmlinux.o(.data+0x2e3410): Section mismatch: reference to .init.data:mts64_ctl_smpte_time_frames (between 'control.19929' and 'snd_mts64_rawmidi_output_ops') WARNING: vmlinux.o(.data+0x2e3418): Section mismatch: reference to .init.data:mts64_ctl_smpte_fps (between 'control.19929' and 'snd_mts64_rawmidi_output_ops') Signed-off-by:
-
Clemens Ladisch authored
Add a callback to the model structure to allow modification of the hardware PCM limits. Signed-off-by:
-
Clemens Ladisch authored
Allow the models to modify mixer controls before they are added to the card. Signed-off-by:
-
Clemens Ladisch authored
Allow the card models to specify whether each of the hardware DMA channels is used. Signed-off-by:
-
